Installation & Commissioning - Advanced
Installation & CommissioningThe operation and functions described in this manual are available from Software Version Mx4100-023, Mx4200-023 andMx4400-023 onwards.www.advancedco.com
Specifications:ItemSpecification DetailsEnclosureSteel IP30Steel IP30Steel IP30Steel IP30Steel IP30Dimensions Hx W x D mm320 x 345 x 88340 x 368 x 125 (/L)475 x 450 x 125475 x 450 x 190 (/D)475 x 450 x 125475 x 450 x 190 (/D)950 x 450 x 190950 x 450 x 190Weight(excludingbatteries)5Kg / 6Kg (/L)10.5Kg / 12Kg (/D)10.5Kg/ 12Kg (/D)20Kg23KgTemperature-5 C to 40 C-5 C to 40 C-5 C to 40 C-5 C to 40 C-5 C to 40 CHumidity95 % Max95 % Max95 % Max95 % Max95 % MaxCable Entries(20mmknockouts)7x top and 7x top rear14x top / 7x top rear (/L)18x top, 9x top rear and2x bottom36x top, 9x top rear (/D)18x top, 9x top rear and2x bottom36x top, 9x top rear (/D)36x top, 9x top rear and2x bottom36 x top, 9 x top rearand 2 x bottomMains Supply230V 10%, -15%50/60Hz AC0.4A max220-240V, 10%, -15%47 –63 Hz AC1 A max220-240V, 10%, -15%47 –63 Hz AC1 A max220-240V, 10%, -15%47 –63 Hz AC1 A max220-240V, 10%, -15%47 –63 Hz AC2 A maxBatteryCapacity24V 4Ah Internal (min)24V 7Ah Internal (max)(Mx-4100)24V 12Ah Internal (max)(Mx-4100/L).24V 4Ah Internal (min)24V 17Ah Internal (max)(Mx4200)24V 38Ah Internal (max)(Mx4200/D)24V 4Ah Internal (min)24V 17Ah Internal (max)(Mx-4400)24V 38Ah Internal (max)(Mx-4400/D)24V 4Ah Internal (min)24V 48Ah Internal (max)(2x 24Ah in parallel)2x 24V 4Ah Internal(min)2x 24V 38Ah nsated2.4ATemperatureCompensated2 x 2.4ATemperatureCompensatedMax BatteryResistance( /-10%)2.6Ω1.5Ω1.5Ω1.5Ω1.5ΩPower SupplyOn-board 24V DC, 2AHigh Efficiency SwitchedModeSeparate 24V DC, 4AOff-LineSwitched ModeSeparate 24V DC, 5AOff-LineSwitched ModeSeparate 24V DC, 5AOff-LineSwitched Mode2x Separate 24V DC, 5AOff-LineSwitched ModeImax(a) Imax(b)1.4A2.6A2.6A2.6A2.6AOutputVoltage118.0V – 32.0V18.0V – 28.0V18.0V – 28.0V18.0V – 28.0V18.0V – 28.0VRipple (Vpkpk)3.5V1.0V1.0V1.0V1.0VNumber ofFire Zones100 max(250 when networked)200 max, across 2 loops(1000 when networked)200 max, across 4 loops(1000 when Networked)200 max, across 4 loops(1000 when Networked)400 max, across 8 loops(1000 when Networked)Number ofLoops11 to 21 to 41 to 42 to 8Devices perLoopApollo 126 detector/call points per loop (max)Hochiki 127 detector/call points per loop (max)Loop Current 2(max. / Loop)400mA quiescent500mA alarm400mA quiescent500mA alarm400mA quiescent500mA alarm400mA quiescent500mA alarmProtocolsApollo: S90, XP95, Discovery, Explorer & Hochiki ESPSounder 2Outputs2 x 1A Programmable2 x 1A Programmable4 x 1A Programmable4 x 1A Programmable8 x 1A ProgrammableRelay Outputs2 x1A 30VAC/DC (max)10mA 5V (min)Programmable2 x 1A 30V AC/DC(max)10mA. 5V(min) Programmable2 x 1A 30V AC/DC(max) 10mA. 5V (min)Programmable2 x 1A 30V AC/DC(max) 10mA. 5V (min)Programmable4 x 1A 30V AC/DC(max) 10mA. 5V (min)ProgrammableOpenCollectorOutputs2 x Programmable10mA 30V DC (max)2 x Programmable10mA 30V DC (max)2 x Programmable10mA 30V DC (max)2 x Programmable10mA 30V DC (max)4 x Programmable10mA 30V DC (max)Digital Outputs---6 x Programmable6 x Programmable6 x Programmable12 x ProgrammableAuxiliarySupply Output24V DC, 500mA24V DC, 500mA24V DC, 500mA24V DC, 500mA2 x 24V DC, 500mAEvent Log1000 Event & Diagnostic 500 Fire400mA quiescent500mA alarm2As our policy is one of constant product improvement the right is therefore reserved to modify product specifications without prior notice12Minimum/maximum specifications for the AUX, and Sounder outputs. Detector Loop voltage is not dependant on AC or battery voltage.Total output current and panel load should not to exceed Imax(a).www.advancedco.com
Table of Contents1INTRODUCTION1.1STANDARDS1.2CAUTIONS AND W ARNINGS1.3DESCRIPTION1.4EN54 FUNCTIONS1.5EN54 OPTIONAL FEATURES WITH REQUIREMENTS1.6INSTALLATION APPROVALS1.6.1 Fire System Installations1.6.2 Wiring Regulations2INSTALLATION2.1IDENTIFICATION OF PARTS2.1.1 Mx-41002.1.2 Mx-4200 & Mx-44002.1.3 Mx-4400/LE2.1.4 Mx-48002.2INSTALLING THE MX-4100 ENCLOSURE2.2.1 Removing and Replacing the Enclosure Cover of the Mx-41002.2.2 Removing the Chassis2.2.3 Mounting the Enclosure2.2.4 Remounting the Chassis2.2.5 Recommended Cable Routing Arrangement2.3INSTALLING THE MX-4200 & 4400 ENCLOSURES2.3.1 Opening the Enclosure Cover2.3.2 Removing the Chassis2.3.3 Mounting the Enclosure2.3.4 Remounting the Chassis2.3.5 Recommended Cable Routing Arrangement2.4INSTALLING THE MX-4400/LE AND MX-4800 ENCLOSURES2.4.1 Opening the Enclosure Cover2.4.2 Removing the Chassis2.4.3 Mounting the Enclosure2.4.4 Remounting the Chassis2.4.5 Recommended Cable Routing Arrangement2.5LOOP DRIVER INSTALLATION2.5.1 Fitting the cards in the Mx4200, Mx-4400 & Mx-48002.5.2 Removing a Loop Driver Card2.6LOCAL PERIPHERAL MODULES2.6.1 Peripheral Bus Interface Adaptor2.6.2 Routing Interface Card2.7WIRING INSTALLATION2.7.1 AC Mains 32.7.42.7.52.7.62.7.72.7.82.7.92.7.102.7.113Cable GlandBattery InstallationMx-4100Mx-4200 & Mx-4400Mx-4400/LE & Mx-4800Battery Temperature MonitoringDetector Loop InstallationSounder CircuitsRelay CircuitsOpen Collector OutputsAuxiliary Supply OutputSwitch InputsRS232 InterfaceIsolated Bus InterfaceRouting 525262626272727PROGRAMMING283.1INTRODUCTION3.1.1 Access Levels2828www.advancedco.com3
3.1.2 Memory Lock3.1.3 Navigating through menus3.1.4 Changing Text Descriptions3.1.5 Numeric data entry3.2RECOMMENDED PROGRAMMING PROCEDURE3.3LEVEL 3 MENU FUNCTIONS3.3.1 Loops3.3.2 Loops – vice TextActionSensitivityO/P GroupAdditional InfoDevice TestingLoops – Auto Learn3.3.33.3.3.13.3.3.23.3.3.33.3.3.4Normal Procedure / Initial learnProcedure if the Panel finds Devices MissingProcedure if the Panel finds Devices AddedProcedure if the Panel finds Devices ChangedLoop – CalibrateLoop – .8.13.3.8.23.3.8.33.3.8.43.3.9Default Output SettingsCauseStyleCopying Output Settings to Multiple ZonesInvestigation Delays3.3.9.13.3.103.3.113.3.123.3.13Overriding Delays at Level 1Time and DateView OptionsPasswordsPanel3.3.13.13.3.143.3.15AC Fail DelayPC 24242434343434444NetworkPanel ZoneService NumberService Due DateTrace Logging ModeDetector BlinkingEarth Fault NotificationRouting InterfaceResound AlarmsProgram IDConfig Data4444444545454646464647SERVICE AND MAINTENANCE484.1M AINTENANCE SCHEDULE4.1.1 Daily Actions4.1.2 Monthly Actions4.1.3 Quarterly Actions4.1.4 Annual Actions4.2REPLACEMENT OF COMPONENTS4.2.1 y BatteriesLithium Battery4950Liquid Crystal Display50APPENDICES5.142828292930303131APPENDIX 1 – FORGOTTEN LEVEL 3 PASSWORD5151www.advancedco.com
5.2APPENDIX 2 – RECOMMENDED FIRE RATED CABLES5.2.1 Detector Loop Lengths5.2.2 Sounder Circuit Lengths5.2.3 Fire / Fault Routing Circuit Lengths5.2.4 Network Cables5.3APPENDIX 3 – BATTERY STANDBY CALCULATION CHART5.3.1 Mx-41005.3.2 Mx-4200 / Mx-4400 / Mx-48005.4APPENDIX 4 – CAUSE AND EFFECT PROGRAMMING EXAMPLE5.4.1 Introduction5.4.2 Output Groups5.4.3 Styles5.4.4 Output Group Programming5.5APPENDIX 5 – APOLLO INFORMATION5.5.1 View Drift5.5.2 Rapid Compensation5.5.3 View EEPROM5.5.4 Loop Isolators5.5.5 Sounder Group Addressing5.6APPENDIX 6 – HOCHIKI ESP INFORMATION5.6.1 Unprocessed Analogue information5.6.2 CHQ-BS / CHQ-WS Sounders5.7APPENDIX 7 – MX4000 SERIES LOOP OUTPUT DRIVE CAPABILITY5.7.1 Hochiki5.7.2 Apollo5.8APPENDIX 8 – OTHER USEFUL DOCUMENTS5.9APPENDIX 9 – MX-4800 / NETWORK DESIGN PRINCIPLES5.9.1 Mandatory Functions5.9.2 Network Wiring5.10APPENDIX 10 – MX SERIES PRODUCT CAPABILITIES / M AX 58585859595960606061616162636363645
1 Introduction1.1 StandardsAdvanced Electronics Ltd declares that the products identified below conform to the essential requirementsspecified in the Construction Products Directive 89/106/EEC:0086-CPD-549125EN54-2: 1997 A1:2006Control and indicating equipment for fire detection and firealarm systems for buildingsProvided options:Outputs to Fire Alarm DevicesOutput to Fire Routing EquipmentOutput to Fault Routing EquipmentInvestigation Delays to OutputsDependency on more than one alarm signalFault Signals from PointsDisablement of PointsAlarm CounterTest ConditionStandardised Input / OutputEN54-4: 1997 A1:2002 A2:2006Power supply equipment for fire detection and fire alarmsystems for buildingsMx-4100, Mx-4100/L, Mx-4200, Mx-4200/D, Mx-4400, Mx4400/D, Mx-4400/LE and Mx-4800In addition, the products comply with the following:Low Voltage Directive 2006/95/ECEN60950-1: 2006Safety of information technology equipmentElectromagnetic Compatibility Directive 2004/108/EC6EN61000-6-3:2001Emissions, Class BEN50130-4: 1995 A1:1998 A2: 2003Immunity, Product Family Standardwww.advancedco.com
1.2 Cautions and WarningsSTOPBEFORE INSTALLATION – Refer To the Ratings shown on the label insidethe product and to the ‘Specifications Chart’ in this document.Please read this manual carefully. If you are unclear on any point DO NOTproceed. Contact the manufacturer or supplier for clarification and guidance.Only Trained service personnel should undertake the Installation,Programming and Maintenance of this equipment.This product has been designed to comply with the requirements of the LowVoltage Safety and the EMC Directives. Failure to follow the installationinstructions may compromise its adherence to these standards.ATTENTIONOBSERVE PRECAUTIONSFOR HANDLINGELECTROSTATICSENSITIVE DEVICESThis equipment is constructed with static sensitive components. Observe antistatic precautions at all times when handling printed circuit boards. Wear ananti-static earth strap connected to panel enclosure earth point. Before installingor removing any printed circuit boards remove all sources of power (mains andbattery).1.3 DescriptionThis manual covers the installation, programming and commissioning of the Mx-4100, Mx-4200, Mx-4400 andMx-4800 Fire Alarm Control Panels. Refer to the User Manual (Document No. 680-015) for details of how tooperate the panel.The Mx-4100 is a Single Loop, Analogue Addressable Fire Alarm Control Panel.The Mx-4200 is a Multiple Loop, Analogue Addressable Fire Alarm Control Panel with provision for up to twoloops.The Mx-4400 is a Multiple Loop, Analogue Addressable Fire Alarm Control Panel with provision for up to fourloops.The Mx-4800 is a Multiple Loop, Analogue Addressable Fire Alarm Control Panel with provision for up to eightloops.All models are designed for use with the Apollo Discovery, Explorer, XP95 and Series 90 and Hochiki ESP firedetection devices.Install the panel, detection loops, sounder circuits, etc. in accordance with the instructions in Section 2and then program the operation in accordance with the instructions detailed in Section 3.www.advancedco.com7
1.4 EN54 FunctionsThis Fire Alarm Control Panel is compliant with the requirements of EN54 parts 2and 4 (1997).In addition to the basic requirements, the following optional functions are providedand these comply with the requirements of EN54.C.I.E Optional FunctionsIndicationOutputsControlsOutputs to Fire Alarm DevicesOutputs to Fire Routing EquipmentInvestigation Delays to OutputsCo-incidence DetectionAlarm CounterFault Signals from PointsOutput to Fault Routing EquipmentDisablement of PointsTest ConditionStandardised I/OP.S.E FunctionsOperation from a main power supplyOperation from a standby batteryMonitor and Charge the Standby BatteryRecognise and Notify Supply FaultsEN54-2 Clause7.87.97.117.127.138.38.99.51011EN54-4 Clause5.15.25.35.4This Fire Alarm Control Panel also supports additional functions that are not coveredby EN54. These are as follows:Additional FunctionAuxiliary Power Supply OutputAuxiliary Relay OutputsProgrammable Cause / Effect on Outputs (Phased Evacuation)Printer Option8Refer toParagraphs2.7.72.7.55.4User Manualwww.advancedco.com
1.5 EN54 Optional Features with RequirementsIn addition to the mandatory requirements of EN54 Part 2, the Control and Indicating Equipment (C.I.E)supports the following optional features with requirements: Outputs to Fire Alarm Devices.Section 7.8The C.I.E has provision for connection to Fire Alarm Devices. It is possible to Silenceand Resound the alarms at Level 2. Refer to the User Manual for further information.Refer to Sections 3.3.8 and 3.3.9 for information on output programming.Outputs to Fire Routing Equipment.Section 7.9The C.I.E has provision to signal the fire condition to a remote receiving station suchas the fire brigade office. Requires installation of a routing interface card. Refer toSections 2.6.2, 2.7.11, 3.3.8, 3.3.9 and 3.3.15.8 for further informationDelays to Outputs.Section 7.11The C.I.E has provision for Output and Investigation Delays. Refer to Sections 3.3.8& 3.3.9 for further informationCoincidence Detection.Section 7.12The C.I.E has provision for Coincidence Detection. Refer to Section 3.3.8 for furtherinformation. Types B and C are supported.Alarm Counter.Section 7.13The C.I.E has provision record the number of times that the fire alarm condition isentered. Refer to the User Manual for further information.Fault Signals from Points.Section 8.3The C.I.E is able to receive and process fault signals from points. These are indicatedon a per zone basis. Refer to the User Manual for further information.Outputs to Fault Routing Equipment.Section 8.9The C.I.E has provision to signal the fault condition to a remote receiving station suchas the service centre office. Requires installation of a routing interface card. Refer toSections 2.6.2, 2.7.11, 3.3.8, 3.3.9 and 3.3.15.8 for further informationDisablement of Points.Section 9.5The C.I.E has provision for enabling and disabling signals from points. Refer to theUser Manual for further information.www.advancedco.com9
Test Condition.Section 10The C.I.E has provision for testing the installation on a per zone basis. Refer to theUser Manual for further information.Standardised Input/Output interface.Section 11Standardised I/O interfaces are supported over the Ad-Net Network.1.6 Installation Approvals1.6.1 Fire System InstallationsThe panel must be installed and configured for operation in accordance with these instructions and theapplicable code of practice or national standard regulations for fire systems installation (for example BS5839-1:2002) appropriate to the country and location of the installation.1.6.2 Wiring RegulationsThe panel and system must be installed in accordance with these instructions and the applicable wiring codesand regulations (for example BS7671) appropriate to the country and location of the installation.10www.advancedco.com
2 Installation2.1 Identification of PartsThe following diagrams show the major parts of the panels.2.1.1 Mx-4100ChassisAssemblyEarth Lead toCoverRearEnclosureAC MainsInputBatteryLeads2.1.2 Mx-4200 & Mx-4400AC www.advancedco.com11
2.1.3 Mx-4400/LEBus-bars for cable earthconnectionsChassis AssemblyLoops 1 - 4Viewing Windowfor Loops 1-4Battery ShelfLoops 1 - 4AdditionalBattery ShelfRear EnclosureDoorEarth Lead toCover2.1.4 Mx-4800Bus-bars for cable earthconnectionsChassis AssemblyLoops 1-4Chassis AssemblyViewing Windowfor Loops 1-4Loops 5-8Viewing Windowfor Loops 5-8Battery ShelfLoops 1-4Battery ShelfLoops 5-8Rear EnclosureDoorEarth Lead toCover12www.advancedco.com
2.2 Installing the Mx-4100 EnclosureThe panel can weigh in excess of 15kg when the batteries are installed. Use the appropriatefixing hardware to secure the panel to the wall. Observe recommended lifting practices toguard against spinal injury.2.2.1 Removing and Replacing the Enclosure Cover of the Mx-4100The enclosure cover is fixed in place with two tamper resistant hexagon key screws. These require the use of a2.5mm Allen Key. The enclosure cover must be connected to earth. When replacing the cover, always ensurethat the earth lead spade terminal is securely seated onto the blade terminal in the back box.2.2.2 Removing the ChassisIt is recommended that the chassis be removed before fitting the panel to the wall. To remove the chassis:Disconnect the earth cable connecting the chassis to the spade terminal on the rear enclosure.Remove the two screws holding the chassis to the back box. Keep these items in a safe place for later re-use.Unplug the 3-way connector feeding the power supply to the Base Card. Carefully remove the chassis from therear enclosure and place in a safe place to prevent accidental damage.Do not lift the chassis by holding onto any of the printed circuit cards. Hold the chassis by themetal plate only.2.2.3 Mounting the EnclosureFirstly, remove the required knockouts for the installation wiring. There are sufficient knockouts on the top of theenclosure for all installation wiring. In addition, there are knockouts at the top of the back wall, if required, forrear entry cabling.The enclosure is provided with four fixing points.Ensure that there is sufficient space to allow thecover to be removed / replaced when the panel ismounted.17EarthStuds x2315Drill the required holes in the supporting wall usinga drill bit diameter 7.0 mm and plug with a suitable40mm long expansion plug. Affix the panel to thewall with M5 screws (length 40mm) or No.10screws (length 1½”).270274The diagram opposite shows the positions of thefour holes. Use all four positions to ensure thepanel is held securely to the wall.34035Cable TieAnchor Points x6Finally, use a brush to remove any dust or swarffrom inside the enclosure.Enclosure Size and Fixing Point Dimensions2.2.4 Remounting the ChassisCarefully replace the chassis and fix into place using the two screws.Reconnect the chassis earth cable to the spade terminal in the rear of the enclosure and then reconnect thesupply lead from the transformer to the Base Card.www.advancedco.com13
2.2.5 Recommended Cable Routing ArrangementIt is recommended that the routingarrangement shown in the diagramopposite be employed.AC PositionsSegregate the low voltage wiring (LoopCircuit, Sounder Circuits and AUX Supply)from the AC Mains Wiring.Segregate any wiring connected to therelay contacts.Eyelets are provided in the rear of the backbox to enable the cables to be securelyfastened using tie-wraps.FS2BATRefer to Appendix 2 – Recommended FireRated Cables for further information oncable types to be used.Refer to specific sections on how to installAC Mains input and loop, sounder, relayand AUX outputs circuits.FS1SupplyInternal arrangement showing recommended routing ofcables.2.3 Installing the Mx-4200 & 4400 EnclosuresThe panel can weigh in excess of 20kg when the batteries are installed. Use theappropriate fixing hardware necessary to secure the panel to the wall. Observerecommended lifting practices to guard against spinal injury.2.3.1 Opening the Enclosure CoverThe Mx-4200 & Mx-4400 are provided with a key-lock assembly for securing the hinged door to the back box.Insert and turn the key to open the enclosure.2.3.2 Removing the ChassisIt is recommended that the chassis beremoved before fitting the panel to thewall. To remove the chassis:Refer to the diagram opposite.Disconnect the earth cable connectingthe chassis to the spade terminal on therear enclosure.FixingScrews.Remove the bottom two screws holdingthe chassis to the back box. Keep theseitems in a safe place for later re-use.Loosen the top two screws holding thechassis to the back box via the keyholeslots. The chassis assembly can now beremove
2 x 1A Programmable 2 x 1A Programmable 4 x 1A Programmable 4 x 1A Programmable 8 x 1A Programmable Relay Outputs 2 x1A 30VAC/DC (max) . 1.6.1 Fire System Installations 10 1.6.2 Wiring Regulations 10 2 INSTALLATION 11 . 3.3.2.10 Devic
Defining Commissioning for GSA Buildings Commissioning ensures the delivery of efficient, durable, and comfortable facilities. ASHRAE Guideline 0‐2019 The Commissioning Process defines commissioning as follows: “Commissioning Process (Cx): a quality‐focused process for enhancing the delivery of a project. The
Commissioning Your Way To High Performance Buildings THE COMMISSIONING PROCESS Core Phases Of The Commissioning Process PRE-DESIGN STAGE The owner selects the design team, which includes the commissioning authority (CxA). Commissioning authority consists of the initial Cx team and team leader, and they are involved from project initiation
SNC Commissioning Guide (LIT-12013295) NIEx9 Commissioning Guide (LIT-12011922) Commissioning a network engine for secure communication LCS85 Installation and Upgrade Instructions (LIT-12011623) Commissioning a secure NAE55 (NAE-S) with embedded encryption technology (available to Johnson Controls employees only) NAE-S Commissioning Guide .
ABOUT THIS GUIDE Intended Audience 4 MAXPRO VMS R300 Viewer Edition Commissioning and Installation GuideINTENDED AUDIENCE This guide is intended for the field and commissioning engineers of MAXPRO VMS. INSTALLATION AND COMMISSIONING GUIDESTRUCTURE The following table describes the contents of each chapter in this guide.
Commissioning the Building Building Commissioning Building commissioning: Is a systematic and designed process coordi nated by a commissioning authority or team. Includes documentation, verification pro cedures, functional performance tests, valida tion, and training. Is performed specifically to ensure building
“Commissioning” (Cx) Process Applied to New Buildings “Re-Commissioning” (RCx) Process Repeated for Buildings That Have Been Commissioned “Existing Building Commissioning” (EBCx) Process Applied to Existing Buildings Not Previously Commissioned (replaces the older term “Retro-commissioning”). 5
This guideline describes the total building commissioning process and the responsibilities of the Commissioning Authority and the Owner. Selecting and developing a Commissioning Plan following this guideline assures Caltech of whole-building commissioning meeting the OPR, and a sustaina
Commissioning Commissioning is the phase in a project when design process fluids are introduced to the process. Note that for hydrocarbon systems the commissioning activities commence with inerting operations. Commissioning activities normally consist of activities associ
