SPULEN MK7/A3/S3 Throttle Pipe

2y ago
28 Views
2 Downloads
748.05 KB
10 Pages
Last View : 1m ago
Last Download : 3m ago
Upload by : Maleah Dent
Transcription

SPULEN MK7/A3/S3 Throttle Pipe7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com

Spulen MK7/A3/S3Throttle pipeInstall instructions7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com01

Spulen MK7/A3/S3Throttle pipeInstall instructions1. Loosen the 7mm hose clamp at thethrottle body.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com02

Spulen MK7/A3/S3Throttle pipeInstall instructions2. Remove the 8x T-25 screws securing thelower splash guard.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com03

Spulen MK7/A3/S3Throttle pipeInstall instructions3. Release the radiator hose from the factorythrottle pipe (red arrow). Loosen the T-30 torxsecuring the pipe to the block (blue arrow).7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com04

Spulen MK7/A3/S3Throttle pipeInstall instructions4. Remove the T-30 torx securing thefactory pipe to the block (red arrow).Disconnect the MAP sensor (blue arrow).Loosen the 7mm hose clamp (green arrow).Remove the factory throttle pipe.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com05

Spulen MK7/A3/S3Throttle pipeInstall instructions5. Remove the 2x T-25 screws securing theMAP sensor.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com06

Spulen MK7/A3/S3Throttle pipeInstall instructions6. Install the MAP sensor into the newthrottle pipe and secure with the included5mm allen head bolts. Install the siliconecoupler and loosely install the hose clampson the pipe.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com07

Spulen MK7/A3/S3Throttle pipeInstall instructions7. Install the new throttle pipe onto the car.Insure proper clearance between radiatorfans and tighten 8mm clamps at the throttlebody.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com08

Spulen MK7/A3/S3Throttle pipeInstall instructions8. Reconnect the MAP sensor. Reconnectthe intercooler hose that wasdisconnected in step 4.9. Reinstall the splash guard removed instep 2.7716 Wiles Rd.Coral Springs, FL 33067www.uspmotorsports.com09

Spulen MK7/A3/S3 Throttle pipe Install instructions 7716 Wiles Rd.Coral Springs, FL 33067 www.uspmotorsports.com 08 7. Install the new throttle pipe onto the car. Insure proper clearance between radiator fans and tighten 8mm clamps at the throt

Related Documents:

Volkswagen MK7 & Audi 8V A3/S3 Kohlefaser Luft-Technik Intake System Installation Guide - Click HERE to Shop. VW MK7, AUDI A3/S3 KOHLEFASER LUFT5TECHNIK INTAKE SYSTEM INSTALLATION . connect the new ECS hose in its place. 3. Now it's time to swap the hoses at the

set to type 3. For 3-wire throttle pots or EZ Go with ITS converter box, set to Type 2. The default is Type 2. Throttle: This allows the Throttle range to be calibrated. Cycle the program options to “Throttle” on the Dash Display, select Street Mode, press the Accelerator Pedal to the floor (Max Throttle).

1-8@1.722 A A Manual Valve Cutback Plunger Kickdown Compensator Throttle Boost Throttle Body Throttle Valve T Throttle body No Vent here Check Valve P R N D2 D1 L D2 Starts in 2nd. Shifts to 3rd Kickdown to 2nd but not to 1st D1 Starts in 1st and shifts 1-2 & 2-3 Kickdown to 2nd or 1st, speed controlled L Starts in Low [1st] and does not shift.

wall respectively. The reduction is both dependent on pressure ratio and throttle plate angle. The effective area has showed to follow the same behaviour as the mass flow rate for the larger simulated throttle plate angle 31 , i.e. an increase as the pressure drop over the throttle plate becomes larger. At the smaller throttle plate angle 21 .

Suitable for Golf MK7 2.0lt GTI (CHHB) Audi A3 A6811/A6812 . Suitable for Golf/Jetta MK4/5 Polo2 Audi A3/4 A12112/A12113 BUMPER SLIDE LH/RH Suitable for Jetta 2015 A5568/A5569 BEARING CARRIER LH/RH Suitable for Polo2 A11003 TIMING CHAIN KIT . GLS 2005-2013 A8366A OIL FILTER Suitable for MK7 VW-UP Audi A3 1.2/1.4 TFSI (CMBA/CPTA/ CJZA/CJZB .

Audi 8V A3/S3 - VW MK7 Golf/GTI/R Dogbone Mount and Bushing Insert INTRODUCTION subframe bushing that supports the rear of the dogbone mount has one of the toughest unwanted noise and vibration out of the chassis. Our new

Motronic engine control module (ECM), ignition system, throttle valve control module ws white sw black ro red br brown gn green bl blue gr grey ge yellow li violet No. 72/4 EuroVan F60 - Closed Throttle Position (CTP) Switch G69 - Throttle Position (TP) Sensor G88 - Throttle Position (TP) S

Soldier’s level of functioning as of the last developmental counseling session IAW AR 380-5, paragraph 5-5; and AR 25-2, paragraph 4-5. 2. First line leaders should: a. Conduct counseling sessions addressing the domains identified on the USA SLRRT with all Soldiers for whom they are responsible IAW paragraph F: Policies and