Operations Guide ESP-MC, ESP-SAT, ESP-SITE-Satellite And .
Operations GuideESP-MC, ESP-SAT, ESP-SITE-Satellite and Maxicom2 Interface Board (MIB) KitP/N 634593 REV F
Safety InformationWarning!Important safety information and warning messages appear throughout this manual. To ensure correct operationand to avoid additional expense, read this manual thoroughly before you begin installation.“WARNING: A CIRCUIT BREAKER OR CUTOFFSWITCH IS TO BE PROVIDED IN THE FIXED WIRINGTO ISOLATE THE CONTROLLER”“ATTENTION: UN DISJONCTEUR OU UNIMTERRUPTEUR DOIT ETRE INSTALLE SUR LEPRIMAIRE POUR ISOLER LE PROGRAMMATEUR”“MEMORY IS RETAINED BY A BATTERY WHICH ISTO BE DISPOSED OF IN ACCORDANCE WITHLOCAL REGULATIONS”“LA MEMOIRE EST MAINTENUE GRACE A UNEBATTERIE RECHARGEABLE A DISPOSER SELON LAREGLEMENTATION LOCALE”Caution iconsiiThe lightening flash with arrowheadsymbol, within an equilateral triangle, isintended to alert the user to thepresence of uninsulated “dangerousvoltage” within the product’s enclosurethat may be of sufficient magnitude toconstitute a risk of electric shock topersons.L’éclair avec is symbole de la flèche,placé dans les limites d’un triangleéquilatéral est prévu pour avertirl’utilisateur de la présence de “tensiondangereuse” non isolée dans l’enceintedu produit qui pourrait ëtre d’uneimportance suffisante pour présenter unrisque d’électrocution aux personnes.The exclamation point within anequilateral triangle is intended to alertthe user to the presence of importantoperating and maintenance (servicing)instructions in the literatureaccompanying the product.Le point d’exclamation dans un triangleéquilatéral est prévu pour avertirl’utilisateur de la présence d’instructionsimportantes pour les opérations etl’entretien (service) dans les manuelsfournis avec l’appareil.
ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Welcome to Rain Bird . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1The ESP-MC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1The ESP-SAT Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1The Maxicom 2 Interface Board (MIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1The ESP-SITE-Satellite Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2*For installation instructions see poster included in controller boxLooking at the Controller’s Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Rain Bird RASTER TM (Rapid Station Test Routine) . . . . . . . . . . . . . . . . . . . . . . .7Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7RASTERTM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Beginning the RASTER TM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Station Valve Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Troubleshooting Open and Shorted Valve Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Open Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Short Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Troubleshooting Opens and Shorts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Programming the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Preparing to Program the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Setting the Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Setting up a Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Step 1: Selecting a Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Step 2: Selecting the Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Step 3: Setting the Length of a Station’s Watering Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Step 4: Setting Watering Start Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Step 5: Setting Programs to Stack or Overlap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Step 6: Setting the MV/PUMP Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Setting Rain Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Setting Cycle SoakTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Setting the Water Budget . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Setting Event Day Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21iii
Contents, continuedSetting a Delay between Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Clearing All Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Operating the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Operating Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Operating Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Operating a Program or Programs Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Operating a Station or Stations Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Using the Test Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Using the Sensor Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Fuse Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Using the Diagnostic Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Maxicom2-specific Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Appendix A: Scheduling Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31ESP-MC and ESP-SAT Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Appendix B: Maxicom 2 Central Control System Overview . . . . . . . . . . . . . . .34ESP-SITE-Satellite Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Appendix C: Setting the Channel Number . . . . . . . . . . . . . . . . . . . . . . . . . . . .38Appendix D: ESP-MC Controller Spare Parts List . . . . . . . . . . . . . . . . . . . . . .39Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .inside back coveriv
IntroductionWelcome to Rain BirdThank you for purchasing your new, state-of-the-art Rain Bird controller. For more than six decades, Rain Bird hasled the irrigation industry in meeting all of your water management needs by providing the highest qualityproducts and services available. Your new Rain Bird controller is designed to give you a lifetime of on-site wateringcontrol.The ESP-MC ControllerThe ESP-MC series controller is a stand-alone controller appropriate for residential or commercial use. Thin easy-touse built-in computers offer four programs for up to 40 watering stations. It can also be upgraded to function as asatellite controller that is part of the Maxicom2 irrigation system. For more information about using your2controller with the Maxicom system, see Appendix B, on page 34.The ESP-SAT ControllerThe ESP-SAT series controller is ready to be used in conjunction with the Maxicom2 irrigation system or as astand-alone unit. It is appropriate for residential or commercial use and its easy-to-use, built-in computer offersfour programs for up to 40 watering stations.The Maxicom2 Interface Board (MIB)The Maxicom2 Interface Board (MIB) kit for the ESP-MC controller converts the stand-alone ESP-MC to an ESP-SATcontroller that can be linked to the Maxicom2 system.The ESP-SITE-Satellite ControllerThe ESP-SITE-Satellite controller is ready to be used in conjunction with the Maxicom2 irrigation system. It isappropriate for residential or commercial use and its easy-to-use, built-in computer offers four programs for up to40 watering stations. For information specific to the ESP-SITE-Satellite controller, see Appendix B, page 36 and theESP-SITE-Satellite Installation Guide that came with your controller.The ESP-SITE-Satellite Upgrade Kit for ESP-MC or ESP-SAT controllers converts these controllers to ESP-SITE-Satellitecontrollers.1
Introduction, continuedSpecial FeaturesThe ESP-MC, ESP-SAT and ESP-SITE-Satellite controllers are available as metal wall-mount (WM)or stainless steel pedestal-mount (SS) models, with 8-, 12-, 16-, 24-, 28, 32, 36- or 40-station capability.All configurations have the following special features: Anti-rust, corrosion-resistant design Four independent programsTM Cycle Soak feature for water conservation and erosion control Programs and time are retained, even during power outages Diagnostic circuit breaker that identifies a station with a short circuit Convenient Test Program Rain Delay from 1 to 99 days 365-day calendar with various scheduling options for watering cycles Option to set any day of the month as a non-watering day Cycle and fault indicator lights Easy-to-read liquid crystal display Optional sensors that suspend watering when the soil is wet Universal remote-ready connections True independent day cycles by program Programmable program overlap Station timing from one minute to 12 hoursNote: For installation instructions see poster included in controller box.2
Looking at the Controller’s FaceplateBefore beginning to program or operate your controller, take a moment to become familiar with the controller’sfaceplate. The following pages contain a short description of each of the keys and indicators. Specific instructions forall of the operations you can perform begin on page 7.3
Looking at the Controller’s Faceplate, continuedWATERING SUSPENDED BY SENSORThis light is on when watering has been suspended by a sensor or the sensor jumper wire has been removed andthe sensor switch is in the ACTIVE position.SENSOR OFF/ACTIVEIf you want to activate the sensor, set the switch to ACTIVE. If you wish to override the sensor or there is no sensorconnected to the controller, set the switch to OFF. When no sensor is connected, be certain that the jumper cableconnecting the SENSOR terminals on the controller’s circuit board is installed. If you set the SENSOR switch toACTIVE without a sensor or jumper cable connected, the controller cannot operate the valves and no wateringwill occur. /ONPress to turn a setting on or to advance the setting in the display. /OFFPress to turn a setting off or to decrease the setting in the display.PGMPress to change the program displayed on the screen. When the PGM key is pressed, the indicator on the left sideof the screen cycles through programs A, B, C and D.MAN START/ADV.Press to advance to the next setting in the display or to manually start an operation.FAULT RESETPress to clear the fault reading from the display. Press this key after you have fixed the short circuit indicated bythe diagnostic fault indicator in the display.PUMP/MV STATUSThis light is on when the Master Valve 1 (MV1) circuit is enabled for the active station.STATION STATUSThis light is on when a valve is active.LINKED TO Maxicom2 (ESP-SAT and ESP-SITE-Satellite versions only)This light is on when the STAND ALONE/MAXICOM switch is in the MAXICOM position and the controller isphysically linked to the Maxicom2 system.EVEN DAY CYCLEThis light is on when the controller’s active program is set to water on even days of the month.4
Looking at the Controller’s Faceplate, continuedODD DAY CYCLEThis light is on when the controller’s active program is set to water on odd days of the month.CYCLICAL DAY CYCLEThis light is on when the controller’s active program is set to water in a cycle with a specified number of days.CUSTOM DAY CYCLEThis light is on when the controller’s active program is set to water on specific days of the week.AUTOSet the dial here to have the controller automatically run the programs you set.STATION WATERING TIMESet the dial here to set the length of an individual station’s watering time.WATERING START TIMESet the dial here to set a program’s watering start times. Eight start times are available for each program.MV PUMP STARTSet the dial here to enable or disable Master Valve 1 (MV1) for a particular station.PROGRAM OVERLAPSet the dial here to set programs to either stack or overlap. The default for all programs is stack.TIME/CALENDARSet the dial here to set the time and date.EVENT DAY OFFSet the dial here to set optional day(s) off within the month.RAIN DELAYSet the dial here to delay watering for a specified number of days.MON — SUNSet the dial to the day of the week to turn that day off or on when setting a custom program cycle.CUSTOMSet the dial here to set a program cycle to water on specific days of the week.CYCLICALSet the dial here to set a program cycle to water at specific intervals, such as every day, every second day, everythird day, etc.5
Looking at the Controller’s Faceplate, continuedODD DAYSSet the dial here to set a program cycle that waters on odd days of the month.EVEN DAYSSet the dial here to set a program cycle that waters on even days of the month.WATER BUDGETSet the dial here to set the water budget percentage for a program. The default is 100%.CYCLE SOAK TMSet the dial here to break a station’s watering time into intervals to conserve water and prevent erosion.TEST PROGRAM/STATION DELAYSet the dial here to set and start a test program cycle for all stations. Also, access the Station Delay feature byplacing the dial in this position and holding down the /ON and /OFF keys simultaneously.MANUAL WATERINGSet the dial here to water a station manually.OFF/PROGRAM RESETSet the dial here to shut the controller and its valves down, such as during the winter months. Also reset allprograms by placing the dial in this position and holding down the /ON and MAN START/ADV keys for 10seconds.STAND ALONE/MAXICOM (located on the back of the front panel)If you want your controller to function as a stand-alone unit, set this switch to STAND ALONE. If you want it to functionas a satellite connected to the Maxicom2 system, set this switch to MAXICOM (ESP-SAT and ESP-SITE-Satellite versionsonly). If the controller is not connected to Maxicom2, the position of this switch will have no effect on watering.6
Rain Bird RASTER (Rapid Station Test Routine)TMIntroductionTMRain Bird’s new RApid Station TEst Routine (RASTER ) lets you diagnose field wiring and solenoid problemsquickly and easily.TMThe RASTER sends an electronic signal to each valve on the controller and then displays the valve’s currentoperating condition in the easy-to-read digital display.TMThe RASTER tests and displays two different valve operating conditions: Open — Indicates an open circuit between the controller and the valve. Short — Indicates a short circuit between the controller and the valve.TMThe RASTER is a fast and easy way to make sure the controller’s master valves and all station valves are operatingproperly.TMThe new RASTER feature is available on the Rain Bird ESP-MC, ESP-SAT, ESP-SITE-SAT and ESP-LX controllers.7
Rain Bird RASTER (Rapid Station Test Routine), continuedTMRASTERTM Operation4. Press the “MAN START/ADV”RASTER .to begin theTMUse the following procedure to perform theRASTER on the master valves and all othercontroller station valves.TMBeginning the RASTERTM1. Turn the Programming Dial to “OFF.”2. Press and release the /ONat the same time.and /OFF3. The display will look like the illustration below.85. The display shows “TEST IO” and the indicatorlights on the front panel flash once as theRASTER confirms the proper operation of thecontroller’s front panel lights.TMNOTE: If the front panel is not connected to theoutput board or the controller is disconnectedfrom the main power the display will show themessage “NO OUT.”TMThe RASTER then automatically begins the teston the controller’s master valves and each stationvalve, beginning with the master valve 1.
Rain Bird RASTER (Rapid Station Test Routine), continuedTM6. The display shows “TEST M1” and “TEST M2” asthe RASTER begins to check the operation of themaster valves (an automatic valve installed on themainline pipe upstream from the station valves).TM7. If the display shows “SHORT M1” or “OPEN M1”or “SHORT M2” or “OPEN M2” there may be afaulty circuit between the controller and themaster valve. (On irrigation systems not equippedwith a master valve, the “OPEN M1” or “OPENM2” indicator is normal and requires no service.)See “Troubleshooting Open and Shorted ValveCircuits” on page 11 for more information.9
Rain Bird RASTER (Rapid Station Test Routine), continuedTMStation Valve TestingTMAfter testing the master valves, the RASTERautomatically tests each valve station, in numericalorder, from lowest to highest.1. The display shows the valve’s operating condition(OPEN or SHORT), followed by the stationnumber (up to 40 stations, depending oncontroller model). This sample display indicatesthere is a short on valve station number 4.TM2. The RASTER displays the condition of each valvebeing tested for 10 seconds, and then moves tothe next valve. You can press “MAN/START/ADV”(or any other magenta button) at any time toadvance to the next station to be tested.NOTE: Any controller station that does not have avalve connected to it will display an OPEN signal.For example, if you have a 12-station controller andonly have stations 1 through 10 conn
The ESP-MC, ESP-SAT and ESP-SITE-Satellite controllers are available as metal wall-mount (WM) or stainless steel pedestal-mount (SS) models, with 8-, 12-, 16-, 24-, 28, 32, 36- or 40-station capability. All configurations have the following special features: Anti-rus
Kodak AiO Ink Technology Deep Dive ESP 1.2 / 3.2ESP 1.2 / 3.2 Hero 9.1Hero 9.1 Hero 7.1Hero 7.1 Office Hero 6.1Office Hero 6.1 Hero 5.1Hero 5.1 Hero 3.1Hero 3.1 2011‐ 2013 ESP C110, C310, C315 ESP Office 2150/2170 ESP Office 6150 ESP 7250 ESP 9250 2010‐ ESP 3250 ESP 5250 ESP3 ESP5 ESP7 ESP9 2011 2008‐ 2009 Easyshare 5100 Easyshare 5300 .
ESP 88 and ESP 00 can support a total of 4 cards per ESP for a total of 16 mic/ line inputs and 16 line outputs. The ESP-88 comes pre-loaded with two 4x4 mic/line cards, allowing two additional 4x4 cards to be added. The ESP-00 does not include these cards, so 8 audio input or output cards can be added. PC 0
1 subl 12 , %esp 1 function : 2 movl 3 , 8(%esp ) 2 pushl %ebp 3 movl 2 , 4(%esp ) 3 movl %esp , %ebp 4 movl 1 , (%esp ) 4 subl 16 , %esp 5 c a l l function. Pushes the base pointer (EBP) in the stack, now it’s a saved frame pointer (SFP). Moves the stack pointer (ESP) in EBP, subst
Datasheet Includes: ESP-WROOM-02D ESP-WROOM-02U. About This Guide This document provides introduction to the specifications of ESP-WROOM-02D and ESP- . Core ESP8266 ESP8266 Antenna Onboard antenna IPEX antenna Dimensions (unit: mm) (18.00 0.10) x (20.00 0.10) x (3.20 0.10)
(Postgres) OSISoft Historian A-MQ. ESP Replacement Business Optimization - BPMN. ESP Demo Walkthrough ESP Vibration Simulation ESP Remote Metrics ESP Remote Control. Global visibility to Production KPIs Demo ESP Machine Health Scenario . SSL/TLS – ensure the wire is encrypted
All ESP course designers should know that the job of an effective ESP course design includes: (a) planning and designing an appropriate course suitable for the target ESP groups, (b) deciding on the practical type of syllabus that well meets the basic requirements of the ESP course participants. 1. Theoretical Background to ESP Course Design
ESP-PSRAM64 and ESP-PSRAM64H are 64 Mbit serial pseudo SRAM devices that are organized in 8Mx8 bits. They are fabricated using the high-performance and high-reliability CMOS technology. ESP-PSRAM64 operates at 1.8V and can offer high data bandwidth at 144 MHz clock rate, while ESP-PSRAM64H o
The Zipwhip Messaging API supports both single -user and multi-user authentication. If you use single-user authentication, then all users are Administrators (Admin). There is a single tier of users. If you use multi-user authentication, then at least one user is the Administrator and all other users are Operators. There are two tiers of users .
