V10 & V20 Single Vane Pump - FluiDyneFP
ENGINEERING DATAV10 & V20 Single Vane Pump Versatile Reliable High Performance Low Costw w w. F l u i D y n e F P. c o mE m a i l : c s @ F l u i D y n e F P. c o m
V10 & V20 Single Vane PumpVersatilePriority ValveHigh flow, pressure and speedcapabilities enable these pumps tomeet the needs of modern vehiclehydraulic circuits. Optional flowcontrol and priority valve coversoffer even more versatility.The priority valve cover maintainsnearly a constant flow to a primarycircuit and diverts the remainingflow to a secondary circuit. Flowgoing to the secondary circuit isdetermined by pump delivery. Theprimary circuit is protected by anintegral relief valve but an externalrelief valve must be provided for thesecondary circuit.Flow ControlThe flow control cover limits flowto the operating system to thedesired maximum. Excess flowis diverted to tank. On doublepumps, shaft-end pump deliveryis proportional to speed.The flow control cover also includesa relief valve to limit maximum systempressure.A typical application of a flow controlis in a power steering unit where itprovides a constant supply of oil overthe engine’s mid to high speed range.As a result, pressure-induced radialloads are balanced . bearings haveto carry the external load only.PerformanceLow vane tip/ring loading allowshigh pressure operation. Highspeeds are possible because theinlet flow paths are designed togive uniform oil acceleration thus better filling - particularlyat low inlet pressures.ReliableLow CostThe superior design of these unitsmakes them last longer . they’veproven they’ll hold up in ruggedapplications such as trenchers,backhoes and tractors.FluiDyne Fluid Power's efficientdesign produces extra horsepowerper dollar of pump investment providing industry with low pumpcost per horsepower capacity.Hydraulic BalanceInternal inlet and outlet pressurechambers are diametrically opposed.Single Pump Operating SpecificationsModelSeriesDelivery USgpm@ 1200 rpm7 bar (100 psi)Displ.cm3/r(in3/r)Max.r/minMax.bar(psi)Typical del.L/min (USgpm)@ max.speed &pressureTypical inputkW (hp)@ max.speed &pressureV10V10(N)FV10P12345673,3 (.20)6,6 (.40)9,8 (.60)13,1 (.80)16,4 (1.00)19,5 (1.19)22,8 (1.39)4800450040003400320030002800172 (2500)172 (2500)172 (2500)172 (2500)172 (2500)152 (2200)138 (2000)13,6 (3.6)27,7 (7.3)35,6 (9.4)41,3 (10.9)48,5 (12.8)55,3 (14.6)60,6 (16)5,2 (7)10,1 (13.6)13,3 (17.8)15,2 (20.4)17 (22.8)18,3 (24.5)17,9 (24)V20V20FV20NFV20P67891011121319,5 (1.19)22,8 (1.39)26,6 (1.62)29,7 (1.81)31,5 (1.93)36,4 (2.22)39,0 (2.38)42,5 (2.59)34003000280028002500250024002400172 (2500)172 (2500)172 (2500)172 (2500)172 (2500)172 (2500)152 (2200)152 (2200)61,0 (16.1)63,3 (16.7)67,1 (17.7)75,0 (19.8)81,0 (21.4)86,8 (22.9)87,2 (23)98,1 (25.9)21,6 (29)22 (29.5)24,2 (32.5)26,5 (35.5)27.3 (36.6)28 (37.5)26,8 (36)29,1 (39)Wt.kg(lb.)4,5 - 6,8(10 - 15)7,3 - 8,2(16 - 18)Note: Applicable equations and start-up procedures at end of document.2Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Model CodesV2012F-1P 13S - 1 A 8H22 - (***) - L357114Vane pump16Std. coverSeries10 or 20Pressure–K3Integral valve options(Omit if not required)F – Flow control & reliefP – Priority valve & reliefNF – Flow control & relief w/internal drainMounting165S–T–1234567– 4 L/min (1 USgpm)– 8 L/min (2 USgpm)– 11 L/min (3 USgpm)– 15 L/min (4 USgpm)– 19 L/min (5 USgpm)– 23 L/min (6 USgpm)– 27 L/min (7 USgpm)678910111213– 23 L/min (6 USgpm)– 27 L/min (7 USgpm)– 30 L/min (8 USgpm)– 34 L/min (9 USgpm)– 39 L/min (10 USgpm)– 42 L/min (11 USgpm)– 45 L/min (12 USgpm)– 49 L/min (13 USgpm)––––3/4-16 St. thd(V10F & V20F )–1/2” NPT thd.(V10F & V20F)––––1-3/16”–12 St. thd.(V20 only)––––3/4-16 St. thd.(V10F)3/4-16 St. thd.(V10NF & V20NF)86SAE rated capacity – USgpm(1200 r/min & 100 psi)PrimarySecondaryoutletoutletTank9 /1 6 -1 8 St. thd. 3 /4 -1 6 St. thd. 9 /1 6 -1 8 St. thd.(V 1 0 P )(V 1 0 P )(V 1 0 P )Tank––1-1/16–12 St. thd. 3/4-16 . St. thd. 1-1/16–12 St. thd.(V20 only)(V20F)(V20F)131112386213Priority valve cover1-1/16”–12 St. thd.(V10 only)T(NF onlyoption)Inlet port connections1 5 16 -12 str. thd. (V20 only)1” NPT thread (V10 only)1 1 4” NPT thread (V20 only)1 5 16 -12 str. thd. (V10 only)1 5 8”-12 str. thd. (V20 only)1 3 16 -12 str. thd. (V10 only)123/4”–16 St. thd.(V10 only)SD–P–1/2” NPT thd.(V10 only)3/4” NPT thd.(V20 only)PR10Flow control cover249Outlet port connections7Code83/4-16 St. ��3/4-16 St. thd . 7/8-14 St. thd . 3/4-16 St. thd.(V20P)(V20P)(V20P)–11DesignSubject to change. Installation dimensions remain the same for designs –20through –29.Shafts– Straight keyed– Splined– Splined (V10 only)– Splined– SAE A Spline (V20 only)12(Omit if not required)V10seriesV20seriesFluiDyne Fluid PowerPosition of outlet or primaryoutlet port(Viewed from cover end of pump)A – Opposite inlet portB – 90 CCW from inletC – In line with inletD – 90 CW from inlet91013Shaft Rotation(Viewed from shaft end of pump)L – Left hand for counterclockwise.R – Right hand or ( Omit )Integral valvesFlow rate2 – 8 L/min (2 USgpm)3 – 11 L/min (3 USgpm)4 – 15 L/min (4 USgpm)5 – 19 L/min (5 USgpm)6 – 23 L/min (6 USgpm)7 – 27 L/min (7 USgpm)8 – 30 L/min (8 USgpm)3Relief valve settingA – 17 bar (250 psi)B – 35 bar (500 psi)C – 52 bar (750 psi)D – 70 bar (1000 psi)H – 140 bar (2000 psi)J – 155 bar (2250 psi)K – 175 bar (2500 psi)L – 190 bar (2750 psi)F – 100 bar (1500 psi)G – 121 bar (1750 psi)Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Installation DimensionsV10 SeriesDimensions in millimeters (inches).Additional shaft options shown on page 7.Delivery @1200 rpm& 100 psiAB1 USgpm2 USgpm3 USgpm4 USgpm5 USgpm6 USgpm7 USgpm115,6 (4.55)115,6 (4.55)115,6 (4.55)121,9 (4.80)121,9 (4.80)127,0 (5.00)127,0 (5.00)91,9 (3.62)91,9 (3.62)91,9 (3.62)98,3 (3.87)98,3 (3.87)103,4 (4.07)103,4 (4.07)12,7 (.50)Dimensions? 82,55/82,50? 21,4 (3.250/3.248)(.843).750-16 UNF-2B THD.(SHOWN)OR.500 NPT THD. OUTLET PORT1.3125-12 UNF-2B THD. (SHOWN)OR1.000 NPT THD. OUTLET PORT CLOCKWISEROTATIONAB24,6 (.97)76,2 (3.00)C38,1 (1.50)? 19,05/19,02(.750/.749)? 46(1.81)7,9 (.31)6,35/6,10(.250/.240)44,4(1.75)4,75 (.187) SQ. KEY25,4 (1.00) LONG62,7 (2.47)*SAE“A”FLANGE(REF.)11,9(.47) R.*B1021,13/21,00(.832/.827)D1038,1 (1.50)NO. 1 SHAFT53,2(2.09)A106,3(4.19)? 11,1(.44)2 HOLES? 95,2(3.75)V10F & V10NF SeriesDimensions in millimeters (inches).Additional shaft options shown on page 7.Delivery @1200 rpm& 100 psiAB1 USgpm2 USgpm3 USgpm4 USgpm5 USgpm6 USgpm7 USgpm128,8 (5.07)128,8 (5.07)128,8 (5.07)135,1 (5.32)135,1 (5.32)140,2 (5.52)140,2 (5.52)109,5 (4.31)109,5 (4.31)109,5 (4.31)115,8 (4.56)115,8 (4.56)120,9 (4.76)120,9 (4.76)Dimensions(*V10NF - NO TANK PORT)TANK PORT.750–16 UN–2B THD.OR .500 NPT THREADMAJOR DIA.? 82,55/82,50(3.250/3.248)? 15,2(.60)INLET PORT1.000 NPT THD. OR1.32‘125–12 UN–2B THD.OR 1.1875–12 UN–2B THD.B97,5(3.84)NO. 38 SPLINED SHAFTINVOLUTE SPLINEFLAT ROOT16/32 DIAMETRAL PITCH11 TEETH – 30 PRESS. ANGLE.590 MINOR DIAMETER18,62/18,47(.733/.727)12,7 4,6 (.97)6,35/6,10(.250/.240)? 95,3(3.75)? 21,3? 106,4 (.84)20,6 (4.19)(.81)60,5(2.38)11,9(.47) R.10DA10SAE “A”FLANGE(REF.)OUTLET PORT.750-16 UN-2B THD.4? 11,2 (.44)2 HOLESEmail: cs@FluiDyneFP.com www.FluiDyneFP.com
Installation DimensionsV10P SeriesSECONDARY OUTLET PORT.750-16 UNF-2B THD.SAE O-RING BOSS CONNECTIONDimensions in millimeters (inches).Additional shaft options shown on page 7.Delivery @1200 rpm& 100 psi1 USgpm2 USgpm3 USgpm4 USgpm5 USgpm6 USgpm7 USgpmDimensionsAB130,0 (5.12)130,0 (5.12)130,0 (5.12)136,4 (5.37)136,4 (5.37)141,5 (5.57)141,5 (5.57)50,3(1.98)MAJOR DIA.109,5 (4.31)109,5 (4.31)109,5 (4.31)115,8 (4.56)115,8 (4.56)120,9 (4.76)120,9 .250/.240)60,5(2.38)108,0(4.25).437 D. –THRU2 HOLES31,8(1.25)ACCLOCKWISEROTATION25,4 (1.00) NPTINLET PORT12,7 (.50)COVER POSITION “C”102,9(4.05) 82,55/82,50(3.250/3.248) 15,2(.60)20,6(.81)130,0 (5.12) REF. 21,3(.84) 106,4(4.19)101055,6(2.19)11,9 (.47) R.A30,2 (1.19)16,0 (.63) 95,3(3.75)NO. 38 SPLINED SHAFTINVOLUTE SPLINEFLAT ROOT16/32 DIAMETRAL PITCH11 TEETH – 30 PRESS. ANGLE.590 MINOR DIAMETERTANK PORT FOR PRESSURE RELIEFOF PRIMARY OUTLET PORT.5625-18 UNF-2B THD.SAE O-RING BOSS CONNECTIONPRIMARY OUTLET PORT.5625-18 UNF-2B THD.SAE O-RING CONNECTIONV20 SeriesOUTLET PORT1.062-12 UN-2B STR. THD.SAE O-RINGBOSS CONNECTIONDimensions in millimeters (inches).Additional s haft options shown on page 7.Delivery @1200 rpm& 100 psi6 USgpm7 USgpm8 USgpm9 USgpm10 USgpm11 USgpm12 USgpm13 USgpmDimensionsAB125,2 (4.93)131,6 (5.18)131,6 (5.18)131,6 (5.18)136,6 (5.38)136,6 (5.38)140,2 (5.52)140,2 (5.52)55,6(2.19)NO. 1 SHAFTC102,1 (4.02)108,4 (4.27)108,4 (4.27)108,4 (4.27)113,5 (4.47)113,5 (4.47)117,1 (4.61)117,1 (4.61)12,7 (.50)B31 (1.22)4,1(.16)66,0(2.60)D 19,05/19,02(.750/.749)55,6(2.19)5106.4 (4.19) .00453,1(2.09)10 82,55/82,50(3.250/3.248) 11,1 (.437)2 HOLES47,8 (1.88) R.AFluiDyne Fluid Power.4,76 (1875) X 41,1 (1.62)LONG KEY 67,6(2.66)A55,6(2.19)31,8 (1.25) NPTINLET PORT1011,9(.47) R.Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Installation DimensionsV20F, V20NF, & V20P SeriesDimensions in millimeters (inches).Additional shaft options shown on page 7.Delivery @1200 rpm& 100 psi6 USgpm7 USgpm8 USgpm9 USgpm10 USgpm11 USgpm12 USgpm13 USgpmDimensionsAB149,6 (5.89) 125,7 (4.95)156,0 (6.14) 132,1 (5.20)156,0 (6.14) 132,1 (5.20)156,0 (6.14) 132,1 (5.20)161,0 (6.34) 136,9 (5.39)161,0 (6.34) 136,9 (5.39)164,3 (6.47) 140,5 (5.53)164,3 (6.47) 140,5 (5.53).31,8 (1.25) NPTINLET PORT 18,62/18,47(.733/.727)19,1 (.75)V20PSECONDARY OUTLET PORT.875-14 UNF – 2B STR THDSAE O-RING BOSSCONNECTIONV20F12,7 (.50)TANK PORT12,7 (.50) NPT ( *V20NF - NO TANK .19)31,0(1.22)31,8 (1.25)53,1(2.09) 23,9 (.940)DB62,0(2.44)124,0(4.88)4,1 (.16)A15,7(.62)10 82,55/82,50(3.250/3.248)62,0(2.44)15,7(.62) 11,2(.44)2 HOLESV20PTANK PORT.750-16 UNF – 2B STR THDSAE O-RING BOSSCONNECTION1011,9(.47) RNO. 38 SPLINED SHAFTINVOLUTE SPLINE16/32 DIAMETRAL PITCHFLAT ROOT11 TEETH – 30 PRESS. ANGLE.590 MINOR DIAMETER 47,8 (1.88)V20FOUTLET PORT.750-16 UNF – 2B STR THDSAE O-RING BOSSCONNECTION (* V20NF - ONLY PORT OPTION)V20P PRIMARYOUTLET PORT.750-16 UNF – 2B STR THDSAE O-RING BOSSCONNECTION6Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Optional ShaftsV10 SeriesDimensions in millimeters (inches)Note: No. 1 keyed shaft and No. 38splined shaft shown on page 4.50,0(1.97)41,9(1.65)31,8 (1.25) (#11 SHAFT)41,4 (1.63) (#12 SHAFT)14,7(.58)31,8(1.25)3,3 (.13)#11 SHAFT EXTENSION(SHOWN)INVOLUTE SPLINEFLAT ROOT - MAJOR DIA.FIT 16/32 DIAMETRALPITCH 9 TEETH - .5625 P.D.30 PRESSURE ANGLEMAJOR DIA. - .623/.622MINOR DIA. - .465 MIN.30,2 (1.19) 0 UNF2A THD.#12 SHAFT EXTENSIONINVOLUTE SPLINEFLAT ROOT - MAJOR DIA.FIT 16/32 DIAMETRALPITCH 13 TEETH - .8125 P.D.30 PRESSURE ANGLEMAJOR DIA. - .873/.872MINOR DIA. - .715 MIN3,2 (.125) D.-THRU#6 WOODRUFF KEYNo. 3 shaft extensionNo. 11 & 12 shaft extensionV20 SeriesDimensions in millimeters (inches)Note: No. 1 keyed shaft and No. 38splined shaft shown on pages 5and 6 respectively. No. 62 splinedshaft same as V10 #11 shaftshown above.26,9 (1.06)70,6(2.78)16,8(.66)74,7(2.94)31,8 (1.25)50,8(2.00)#13 WOODRUFF KEY37,3 (1.47)FULLDEPTHOF SPLINE 26,9 (1.06)31,8 (1.25) HEX 23,83/23,81(.9380/.9375) 18,62/18,47(.733/.727)26,08/25,82(1.0267/1.0167) 19,07/19,02(.751/.749).875-18 #2 THD.INVOLUTE SPLINE – 16/32 D.P.FLAT ROOT – 11 TEETH30 PRESSURE ANGLENo. 11 shaft extensionNo. 3 shaft extensionNOTE:No. 3 shaft recommended nuttorque 170 Nm (125 lb. ft.)FluiDyne Fluid Power7Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Typical PerformanceV10 Single PumpsPerformance Constants:Oil temp. 49 C (120 F), viscosity32 cSt (150 SSU) @ 38 C (100 F),inlet pressure zero1 & 3 GPM RINGS13,4 (18)34 (9)11,9 (16)30 (8)10,4 (14)3 GPM RING172 BAR (2500 PSI)69 BAR(1000 PSI)7 BAR (100 PSI)8,9 (12)7,4 (10)1 GPM RING172 BAR (2500 PSI)69 BAR(1000 PSI)7 BAR (100 PSI)6,0 (8)4,5 (6)3,0 (4)1,5 (2)01 & 3 GPM RINGS38 (10)DELIVERY – l/min (USgpm)INPUT HORSEPOWER – kW (hp)14,9 ( 20)3 GPM RING172 BAR (2500 PSI)69 BAR(1000 PSI)7 BAR (100 PSI)27 (7)23 (6)1 GPM RING172 BAR (2500 PSI)69 BAR(1000 PSI)7 BAR (100 PSI)19 (5)15 (4)11 (3)8 (2)4 (1)0800160024003200SPEED – r/min4000048000800160024003200SPEED – r/min400048002, 4 & 6 GPM RINGS61 (16)57 (15)2, 4 & 6 GPM RINGS19,4 (26)16,4 (22)13,4 (18)11,9 (16)6 GPM RING69 BAR(1000 PSI)10,4 (14)8,9 (12)7,4 (10)2 GPM RING172 BAR (2500 PSI)4 GPM RING69 BAR (1000 PSI)6,0 (8)3,0 (4)0800160024003200SPEED – r/min40004 GPM RING7 BAR (100 PSI)69 BAR (1000 PSI)172 BAR (2500 PSI)34 (9)30 (8)27 (7)23 (6)19 (5)2 GPM RING7 BAR (100 PSI)69 BAR (1000 PSI)172 BAR (2500 PSI)11 (3)7 (2)6 GPM RING – 7 BAR (100 PSI)4 GPM RING – 7 BAR (100 PSI)2 GPM RING – 7 BAR (100 PSI)1,5 (2)42 (11)38 (10)15 (4)2 GPM RING69 BAR (1000 PSI)4,5 (6)045 (12)4 GPM RING172 BAR (2500 PSI)14,9 (20)6 GPM RING7 BAR(100 PSI)69 BAR(1000 PSI)152 BAR(2200 PSI)49 (13)DELIVERY – l/min (USgpm)17,9 (24)INPUT HORSEPOWER – kW (hp)53 (14)6 GPM RING152 BAR (2200 PSI)4 (1)004800800160024003200SPEED – r/min400048005 & 7 GPM RINGS64 (17)61 (16)DELIVERY – l/min (USgpm)14,9 (20)13,4 (18)11,9 (16)7 GPM RING138 BAR(2000 PSI)10,4 (14)8,9 (12)7 GPM RING69 BAR – (1000 PSI)5 GPM RING69 BAR – (1000 PSI)7,4 (10)6,0 (8)49 (13)45 (12)42 (11)38 (10)34 (9)30 (8)23 (6)19 (5)3,0 (4)15 (4)7 GPM RING – 7 BAR (100 PSI)5 GPM RING – 7 BAR (100 PSI)0080016002400SPEED – r/min5 GPM RING7 BAR (100 PSI)69 BAR (1000 PSI)172 BAR (2500 PSI)27 (7)4,5 (6)1,5 (2)7 GPM RING7 BAR(100 PSI)69 BAR(1000 PSI)138 BAR(2000 PSI)53 (14)5 GPM RING172 BAR(2500 PSI)16,4 (22)INPUT HORSEPOWER – kW (hp)57 (15)5 & 7 GPM RINGS17,9 (24)11 (3)8 (2)32008080016002400SPEED – r/min3200Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Typical PerformanceV20 Single PumpsPerformance Constants:Oil temp. 49 C (120 F), viscosity32 cSt (150 SSU) @ 38 C (100 F),inlet pressure zerobar (PSI) CODE7 & 13 GPM RINGS106 (28)7 (100)70 (1000)150 (2200)1391 (24)83 (22)83 (22)76 (20)76 (20)68 (18)7 (100)70 (1000)175 (2500)61 (16)117 (100)70 (1000)9175 (2500)61 (16)45 (12)38 (10)53 (14)45 (12)38 (10)30 (8)30 (8)23 (6)23 (6)15 (4)15 (4)8 (2)8 (2)080012001600200024002800bar (PSI)29,8 (40)22,4 (30)14,9 (20)70 (1000)11,2 (15)70 (1000)7,5 (10)7 (100)7 (100)3,7 (5)80012001600200024002800SPEED – r/minFluiDyne Fluid Power12001600200024009 & 11 GPM RINGS175 (2500)18,6 (25)800CODE150 (2200)26,1 (35)0400400INPUT HORSEPOWER – kW (HP)4007 & 13 GPM RINGSINPUT HORSEPOWER – kW (HP)7 (100)70 (1000)175 (2500)68 (18)753 (14)0bar (PSI) CODE9 & 11 GPM RINGS91 (24)DELIVERY – l/min (USgpm)DELIVERY – l/min (USgpm)98 (26)2800bar (PSI)29,8 (40)CODE175 (2500)175 (2500)26,1 (35)22,4 (30)18,6 (25)14,9 (20)70 (1000)70 (1000)11,2 (15)7,5 (10)3,7 (5)0400800120016002000240028007 (100)7 (100)SPEED – r/min9Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Typical PerformancePerformance Constants:Oil temp. 49 C (120 F), viscosity32 cSt (150 SSU) @ 38 C (100 F),inlet pressure zerobar (PSI) CODE98 (26)7 (100)70 (1000)91 (24)12150 (2200)83 (22)76 (20)7 (100)70 (1000)DELIVERY – l/min (USgpm)68 (18)175 (2500)7 (100)70 (1000)175 (2500)61 (16)8653 (14)45 (12)38 (10)30 (8)23 (6)15 (4)8 (2)0INPUT HORSEPOWER – kW (HP)bar (PSI) CODE29,8 (40)150 (2200)26,1 (35)175 (2500)22,4 (30)175 (2500)18,6 (25)14,9 (20)70 (1000)70 (1000)70 (1000)11,2 (15)7,5 (10)7 (100)7 (100)7 (100)3,7 (5)010Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Priority Valve ModelsV10P Single Pumps34 (9)7 BAR (100 PSI)140 BAR (2000 PSI)CONTROLLED FLOW TO PRIORITY CIRCUIT – l/min (USgpm)30 (8)NO. 6 ORIFICE27 (7)23 (6)7 BAR (100 PSI)140 BAR (2000 PSI)19 (5)NO. 3 ORIFICE15 (4)11 (3)8 (2)7 BAR (100 PSI)140 BAR (2000 PSI)NO. 1 ORIFICE7 BAR (100 PSI)140 BAR (2000 PSI)NO. 4 ORIFICE4 (1)027 (7)23 (6)19 (5)15 (4)7 BAR (100 PSI)140 BAR (2000 PSI)11 (3)NO. 2 ORIFICE8 (2)4 (1)08(2)11(3)15(4)V20P Single Pumps19(5)23(6)42 (11)30(8)34(9)38(10)42(11)45(12)49(13)TOTAL PUMP DELIVERY – l/min (USgpm)53(14)NOTE: 12 & 13 RINGSARE RATED AT150 BAR (2200 PSI)PRIMARY– 7 BAR (100 PSI)SECONDARY– 175 BAR (2500 PSI)PRIMARY– 175 BAR (2500 PSI)SECONDARY– 7 BAR (100 PSI)38 (10)CONTROLLED FLOW TO PRIORITY CIRCUIT – l/min (USgpm)27(7)34 (9)57(15)61(16)64(17)NO. 8 ORIFICE30 (8)27 (7)NO. 6 ORIFICE23 (6)19 (5)15 (4)NO. 4 ORIFICE11 (3)8 (2)NO. 2 ORIFICE4 (1)04(2)FluiDyne Fluid TOTAL PUMP DELIVERY – l/min (USgpm)1176(20)83(22)91(24)98(26)106(28)Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Typical PerformanceFlow Control ModelsV10(N)F & V20(N)F Single PumpsCONTROLLED FLOW – l/min (USgpm)34 (9)NO. 8 ORIFICE30 (8)27 (7)23 (6)NO. 4 ORIFICE19 (5)NO. 6 ORIFICE15 (4)11 (3)8 (2)NO. 2 ORIFICE4 (19)80(21)87(23)95(25)102(27)TOTAL PUMP DELIVERY – l/min (USgpm)Speed Correction CurvesV10 &V20 Single PumpsMaximum operating speeds shown onperformance curves are for pumpsoperating at 0 psi inlet condition. Tocompute maximum operating speeds atother inlet conditions, use appropriatespeed rating correction factor.Example:Max. speed @ 0 psi inletCorrection factor @ 5 in. HgMax. speed @ 5 in. Hg inlet2700 r/minx .932511 r/minbar0,170,140,100,070,071.061.04in. Hg54320,210,280,34bar5psiSPEED RCHARGE PRESSURE0.960.94Pump inlet suction should not exceed 5in. Hg vacuum. Positive pressure on inletshould not exceed 0,7 bar (10 psi).12Email: cs@FluiDyneFP.com www.FluiDyneFP.com
Oil RecommendationsThe oil in a hydraulic system serves asthe power transmission medium. It isalso the system’s lubricant and coolant.Selection of the proper oil is arequirement for satisfactory systemperformance and life.The following recommendations willassist in the selection of suitable oils foruse with FluiDyne products. FluiDynedoes not publish a recommendedoil list by brand name or supplier dueto the extremely wide variety of oiltypes on the market.In most cases, use of theserecommendations will lead to selectionof a suitable oil. However, due to thecomplex nature of oil formulation, thevariety of oils available and peculiaritiesof individual hydraulic applications, therewill be rare instances where oil selectedon the basis of these recommendationswill yield unsatisfactory results. FluiDynecannot be responsible for suchexceptions. In this respect, the customeris encouraged to consult his FluiDynerepresentative when selecting an oil.Important Factors In SelectingAn OilAdditives –Hydraulic fluids contain a number ofadditive agents which materially improvevarious characteristics of oil for hydraulicsystems. These additives are selectedto reduce wear, increase chemicalstability, inhibit corrosion and depressthe pour point.Pump performance and reliability aredirectly affected by the antiwear additiveformulation contained in the oil. Oilsproviding a high level of antiwearprotection are recommended foroptimum performance and long life.Viscosity –Viscosity is the measure of fluidity. Theoil selected must have proper viscosityto maintain an adequate lubricating filmat system operating temperature.In addition to dynamic lubricatingproperties, oil must have sufficient bodyto provide an adequate sealing effectbetween working parts of pumps,valves, cylinders and motors, but notenough to cause pump cavitation orsluggish valve action.FluiDyne Fluid PowerOptimum operating viscosity of the oilshould be between 16 cSt (80 SUS) and40 cSt (180 SUS).“Viscosity index” reflects the wayviscosity changes with temperature; thesmaller the viscosity change, the higherthe viscosity index. The viscosity indexof hydraulic system oil should not beless than 90. Multiple viscosity oils, suchas SAE 10W30, incorporate additives toimprove viscosity index (polymerthickened). Oils of this type generallyexhibit both a temporary and permanentdecrease in viscosity due to oil shearen
v10 3 9,8 (.60) 40 00 172 (250 0) 35,6 (9.4) 13,3 (1 7.8) 4,5 - 6,8 v10(n)f 4 13,1 (.80) 3400 172 (250 0) 41,3 (10 .9) 15,2 (20 .4) (1 0 - 15) v10p 5
Series V10, V20, V2010, and V2020 fixed displacement pumps are of Vickers “balanced vane type” construction. V10 and V20 single pumps have rated flow capacities of 1 to 7 USgpm and 6 to 13 USgpm, respectively. Double pumps provide a single power source capable of serv-ing two
MODEL V10, V20 V10 1 - 7 GPM SHAFT 1 - KEYED 11 - SPLINE IFP offers a complete line of economical high performance fixed displacement vane pumps providing flows up to 26 US GPM for mobile and industrial applications. Balanced vane design provides quiet operation, high effici
For Mac OS X v10.7 and v10.8, click Print & Scan. For Mac OS X v10.6, click Print & Fax. 2 Click the Fiery Server in the list of printers, and then click Options & Supplies. 3 To change the installable options, do one of the following: For Mac OS X v10.9, click the Options tab. For Mac OS X v10.6, v10.7, and v10.8, click the .
3042f012 dpa pump 3042f022 dpa pump 3042f050 dpa pump 3042f052 dpa pump 3042f062 dpa pump 3042f080 dpa pump 3042f101 dpa pump 3042f102 dpa pump 12 volt 3042f110 dpa pump 3042f150 dpa pump 3042f152 dpa pump 3042f152-r dpa pump 3042f170 dpa pump 3042f171 dpa pump 3042f172 dpa pump 3042f210 dpa pump 3042f212 dpa pump 3042f213 dpa pump 3042f213-r .
6 EATON Vickers Vane Pumps Single and Double Vane Pumps 698 November 2011 Basic Performance Data - Single and Double Pumps Typical operating characteristics at 1200 r/min with petroleum oil Ring size Data based on performance at oil temperature of 49 C (120 F), viscosity 32 cSt at 38 C (150 SUS at 100 F)
OS: Windows 8.1, Windows 10 Mac OS X v10.10 (Yosemite) OS X v10.11 (El Capitan) macOS v10.12 (Sierra) macOS v10.13 (High Sierra) macOS v10.14 (Mojave) macOS v10.15 (Catalina) AG00021F03I. 1. Load the installation software CD supplied with the product. Display the contents of the CD and dou-
5 Fisher Scientifi c Vacuum Pumps Two Stage Rotary Vane Vacuum Pumps Type Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Rotary Vane Vacuum Pump 100-120 V/200-240 V 50/60 Hz FB654591 FB654601 FB654611 FB654641 Rotary Vane Vacuum Pump 230 V 50/60 Hz FB65458² Rotary Vane Vacuum Pump 115 V 50/60 Hz FB65458A² Maintenance kit 302012-1 302075 302076 302077 302079 .
Department of Aliens LAVRIO (Danoukara 3, 195 00 Lavrio) Tel: 22920 25265 Fax: 22920 60419 tmallod.lavriou@astynomia.gr (Monday to Friday, 07:30-14:30) Municipalities of Lavrio Amavissos Kalivia Keratea Koropi Lavrio Markopoulo . 5 Disclaimer Please note that this information is provided as a guide only. Every care has been taken to ensure the accuracy of this information which is not .
