DVS Ember-Fyre Burner (Version 2.1 Log) Installation .
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Compatibility DVS GSR NB InsertPacking List DVS Ember-Fyre Burner AssemblyNG and LP Air DeflectorsLeft and Right Ember Trays8-Piece Log SetBag of Rock WoolBag of Log EmbersPreparing the Burner1.Remove the 3 screws on the back of the burner.2. Attach the correct air deflector to the burner with the screws removed earlier. Note how the LP airdeflector has a notch along the bottom.NG Air DeflectorPage 1 of 817601874 — 1/15/16LP Air Deflector Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Burner InstallationInstall the burner as shown below (make sure the burner is fully seated over the orifices and pushed allthe way to the right). Install the side ember trays.Page 2 of 817601874 — 1/15/16 Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Log Set Installation!The logs are fragile, especially after being exposed to heat. Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service. Failure to position the parts in accordance with these diagrams or failure to use only partsspecifically approved with this appliance may result in property damage or personal injury. If using propane (LP), convert the appliance before installing the burner and logs. The burner must be correctly positioned before installing the logs. Make sure the burner is fullyseated and the pilot is properly aligned.Rear Log PlacementThe rear log has two holes on the bottom. Place the log so the pins on the burner insert into theholes on the log (see photos below).NOTE: On LP inserts, pushthe log to the back. On NGinserts, pull the log forward.Page 3 of 817601874 — 1/15/16 Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Left Front Log PlacementThe left front log has two holes on the bottom. Place the log so the pin on the burner and the metalbracket insert into the holes on the log (see photos below).NOTE: On LP inserts, pushthe log to the back. On NGinserts, pull the log forward.Right Twig PlacementPlace the right twig on the burner as shown below. Make sure it does not cover any burner holes.Page 4 of 817601874 — 1/15/16 Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Right Front Log PlacementThe right log has two holes on the bottom. Place the log so both burner pins insert into the holeson the log (see photos below). Make sure the log is pushed back so it sits flat.NOTE: On LP inserts, pushthe log to the back. On NGinserts, pull the log forward.Left Cross Log PlacementPlace left cross log as shown below. Note- how the log rests on the flat spots of the back and leftlogs.Page 5 of 817601874 — 1/15/16 Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Right Cross Log PlacementPlace the log as shown below. The right cross log rests on the flat spots of the rear and the right frontlogs.Left Twig PlacementPlace the left twig on the burner as shown below. Make sure it does not cover any burner holes.Page 6 of 817601874 — 1/15/16 Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Center Twig PlacementPlace the center twig on the burner as shown below. Make sure it does not cover any burner holes.The completed installation is shown below.Page 7 of 817601874 — 1/15/16 Travis Industries, Inc.
DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Ember PlacementPlace a layer of embers along any screw heads and visible edges of the burner.Rockwool InstallationThe included rock wool is placed on top of the burner to enhance the glow from the burner. The rockwool works best when it is applied in a very thin, porous layer. The best method for applying therock wool is to brush it on to the burner. Compress a clump of rockwool between your thumb andforefinger. Use a stiff brush to apply a thin layer of rockwool fibers onto the burner. Do not use theentire bag of rockwool. Use only a small amount and save the remainder. Over-use of rockwool willdiminish the glow and may cause sooting or other adverse conditions.Page 8 of 817601874 — 1/15/16 Travis Industries, Inc.
Ember Placement Place a layer of embers along any screw heads and visible edges of the burner. Rockwool Installation The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock wool wo
high-definition detailed logs, Ember-Fyre is the most realistic wood-like gas fire available. The Ember-Fyre Burner is featured on our Bed & Breakfast model. Our 564 and 864 gas fireplaces feature the Ember-Fyre II Burner. Ember-Fyre II represents the next generation of high definition,
Ember 600 Ember 700 Ember 600 Ember 700 Engine The Ember engine comes with; remote control (batteries inserted), operation and installation guides, granule packs, rockwool, crushed glass, vermiculite, and flexible gas connection. 4-sided
a. Fluffed up pieces of ember material one layer thick will produce the best ember glow. Do not place more than one layer of ember material onto the burner. Excess ember material will decrease the ember glow effect. b. Save any remaining
Ebara Submersible Semi-Vortex Pumps Performance Chart Model DVS Model code 50 DVS 5 .4 S (T or blank three phase) Motor output (kW) Frequency (5 50 Hz) Model DVSA Automatic version DVS Manual version DVSJ Parallel alternating version Discharge size (mm) 50Hz Phase (S single phase) 0.03 0.05 0.1 2 3 30 20 15 10 9 8 7 6 5 4
Ember Burner (EB) & H-Burner (HB) For model number and PFS seal refer to attached nameplate. Hargrove gas logs are made with refractory materials. Each log is hand-finished to assure the most realistic, detailed log available. The gas log burner system is designed to bur
rich in fat, oil or alcohol (e.g. rum, cognac, wine). - Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a . 3 Semirapid burner 4 Power burner 5 Auxiliary burner 6 Power burner control knob 7 Semirapid burner control knob 8 Semirapid burner control knob 9 Auxiliary burner control knob.
Machining Technics 5723 1800 h DVS* 1 Numerical Control Machine Tool Operation 5724 885 h AVS* 3 SECT OR 13: COMMUNICATIONS & DOCUMENT ATION Computer Graphics Techniques 5844 1800 h DVS* 1 Printing 5813 1350 h DVS* 1 SECT OR 16: METALLURGI CAL TECHNOLOGY Welding & Fitting 5695 1800 h DVS* 1 SECT OR 19: HEALTH SERVICES
in Prep Course Lesson Book A of ALFRED'S BASIC PIANO LIBRARY. It gives the teacher considerable flexibility and is intended in no way to restrict the lesson procedures. FORM OF GUIDE The Guide is presented basically in outline form. The relative importance of each activity is reflected in the words used to introduce each portion of the outline, such as EMPHASIZE, SUGGESTION, IMPORTANT .
