Connecting Rod Bolt - Enterprise Engine Performance
Connecting Rod BoltConnecting Rod Cap BoltsStep 126 ft. lbs.Step 251 ft. lbs.Step 373 ft. lbs.Crankshaft Main BearingREMOVAL1.2.3.4.Remove engine from vehicle and place on a stand.Remove oil pan and suction tube.Remove the crankshaft rear seal retainer.Remove the front gear housing.
ZoomSized for PrintFig. 1785.The main bearing caps should be numbered. If they are not, be sure to mark them,beginning with number one at the front and ending with number seven at the rear(Fig. 178). CAUTION: DO NOT pry on the main caps to free them from the cylinderblock.
ZoomSized for PrintFig. 1796.Use two of the main bearing cap bolts to wiggle the main cap loose (Fig. 179), beingcareful not to damage the bolt threads. Remove all caps in the same manner.WARNING: USE A HOIST TO AVOID INJURY.
ZoomFig. 183Sized for Print
13. Tighten the bolts in the sequence shown in (Fig. 183) using the following steps: STEP 1-Torque all bolts in sequence to 60 Nm (44 ft. lbs.) torque.STEP 2-Torque all bolts in sequence to 119 Nm (88 ft. lbs.) torque.STEP 3-Torque all bolts in sequence to 176 Nm (129 ft. lbs.) torque.14. Turn the crankshaft to determine that it will rotate freely all 360 . Check the mainbearing cap installations and/or the bearing sizes if the shaft does not turn easily.
ZoomFig. 184Sized for Print
ZoomSized for PrintFig. 18515. Verify crankshaft end play: Push the crankshaft towards one end of its thrust and place16.17.18.19.a dial indicator as shown in (Fig. 184). Zero the indicator needle and push thecrankshaft towards the other end of its thrust and record the crankshaft end clearance(Fig. 185).Install the front gear housing.Install the crankshaft rear oil seal retainer.Install the oil pan and suction tube.Install engine into vehicle.Cylinder Head
ZoomSized for PrintUsing the sequence shown, tighten bolts in the following steps:1.2.3.4.5.Torque bolts to 90 Nm (66 ft. lbs.) (All Capscrews)Recheck to 90 Nm (66 ft. lbs.) (All Capscrews)Torque bolts to 120 Nm (90 ft. lbs.) (Long Capscrews Only)Re-check all bolts to 120 Nm (120 ft. lbs.) (Long Capscrews Only)Tighten all bolts an additional 1/4 turn (90 ) (All Capscrews)
STEP 1-Torque all bolts in sequence to 60 Nm (44 ft. lbs.) torque. STEP 2-Torque all bolts in sequence to 119 Nm (88 ft. lbs.) torque. STEP 3-Torque all bolts in sequence to 176 Nm (129 ft. lbs.) torque. 14. Turn the crankshaft to determine that it will rotate freely all 360 . Check the main
its original connecting rod before another connecting rod bearing cap is removed. 5. Remove the connecting rod bearing cap with the connecting rod bearing. 6. Inspect the connecting rod bearing for damage. If the connecting rod bearing is damaged, replace all main and connecting rod bearings. a. Acceptable bearing wear (1). b.
5mm bolt, nut 4.5-6 6mm bolt, nut 8-12 8mm bolt, nut 18-25 10mm bolt, nut 29-34 12mm bolt, nut 49-59 4mm screw 1.5-2.6 5mm screw 3.5-5 6mm screw 7-11 5mm flange bolt 3.6-6.9 6mm screw 7-11 5mm flange bolt 3.6-6.9 6mm flange bolt 10-14 8mm flange bolt 20-26 Bolt and nut 10mm flange bolt
Jan 10, 2012 · Private Pilot Handbook Machado www.rodmachado.com Rod Machado 5. Rod Machado Rod Rod Machado 6. lift weight thrust drag 1-1 Rod Machado 7 B A C D. Rod Machado 8. 65 1-2 Rod Machado 9 A B. 1-3 . Private Pilot Handbook 2002 Library and Help 30% 100 Cessna 172 Rod Machado 35. Cessna 172 74 3-4 85 74 74 75 75 13 3-5 5 5 10 15 20 13 Rod Machado 36 .
The objective of the present work is to design and analyses of connecting rod made of Forged steel. Steel materials are used to design the connecting rod. In this project the material (carbon steel) of connecting rod replaced with Forged steel .Connecting rod was created in CATIAV5 R19. Model is imported in ANSYS 13.0 for analysis.
FEA and the load analysis results, recommend the best alternative design for the connecting rod. Keywords: Connecting Rod, Finite Element Analysis, Modeling, Static I. Introduction The intermediate component between crank and piston is known as connecting rod. Connecting rod is also known as conrod and is used to connect the piston to crankshaft.
1.Engine Oil SABA 13 1.Engine Oil 8000 14 1.Engine Oil 6000 15 1.Engine Oil 3000 16 1.Engine Oil Alvand 17 1.Engine Oil Motor Cycle Engine Oil M-150 18 1.Engine Oil M-100 19 1.Engine Oil Gas Engine Oil CNG-BUS 20 1.Engine Oil G.I.C.X.LA 21 1.Engine Oil G.I.C.X. 22 1.Engine Oil Diesel Engine Oil Power 23 1.Engine Oil Top Engine 24
CONTINUED - WOODWORKS: BEGINNER PROJECT FISHING POLE RACK –2– TOOLS REQUIRED SHOPPING LIST WOOD FINISHING PRODUCTS CUTTING LIST Hand Tools – Crosscut handsaw or miter saw – Rip handsaw – Bar clamps Power Tools – Electric drill with 2" hole saw, 3/8" drill bit and countersink drill bit – Table saw Miscellaneous – Tape measure .File Size: 219KBPage Count: 7Explore furtherWoodworking Plans for a Fishing Rod Rack Home Guides .homeguides.sfgate.com14 Fishing Rod Rack Plans ideas fishing rod rack, rod .www.pinterest.comHow to build a fishing rod rack HowToSpecialist - How to .howtospecialist.comFishing Rod Rack Plans, Fishing Rod Holder Plansfreeww.comFishing Rod Racks and misc Woodworking Plans .woodworkersworkshop.comRecommended to you b
hand, bring the bolt carrier with bolt to the rear as far as possible, and moving the bolt carrier forward a distance of 1 to 2 mm. Lift the rear portion of the bolt carrier and remove it together with the bolt from the receiver. 8. Remove the bolt from the bolt carrier. Take the bolt
