1 Power Commander FC 1 USB Cable Installation Instructions .
Parts List2006-2014 Yamaha Stratoliner/Roadliner2008-2013 Yamaha RaiderInstallation Instructions1112211Power Commander FCUSB CableInstallation GuideDynojet DecalsVelcroAlcohol swabO2 OptimizerTHE IGNITION MUST BE TURNEDOFF BEFORE INSTALLATION!YOU CAN ALSO DOWNLOAD THE PCFCCONTROL CENTER SOFTWARE ANDLATEST MAPS FROM OUR WEB SITE AT:www.powercommander.comPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 r.com2006-2014 Yamaha Stratoliner/Roadliner/2008-2013 Yamaha Raider - 1
SELECTING THE MAP POSITIONThe Dynojet Power Commander Fuel Controller (PCFC) comes loaded with up to tenmaps. Using a #1 Phillips screwdriver, turn the map select dial to toggle between theloaded maps. Refer to the map position table for the maps included in your PCFC.USING THE RPM RANGE DIALSThe Low, Mid, and High RPM Dials refer to the RPM range, in thirds, of your vehicle.Each dial allows /- 10% fuel adjustment on top of what fuel changes are done in themap. With the dial facing straight up, there is no additional fuel change.STATUS LightFor example, if your vehicle revs to 6000 RPM: The low RPM dial will adjust 0-2000 RPM The mid RPM dial will adjust 2001-4000 RPM The high RPM dial will adjust 4001-6000 RPMMAP SelectLOW RPM DialMID RPM DialHIGH RPM DialPositionPosition 1Position 2Position 3USB PortUSING PCFC CONTROL CENTERTake your tuning to the next level with the PCFC Control Center software.1Using your web browser, navigate to www.powercommander.com.2Click Enter Race Ready.3Click Downloads.Note4Click Access Downloads for Power Commander FC.2006-2008 Yamaha Roadliner/StratolinerStock exhaustStock or aftermarket air filterStock O2 sensor disconnected2009-2014 Yamaha Roadliner/StratolinerStock exhaustStock or aftermarket air filter2008-2013 Yamaha RaiderStock exhaustStock or aftermarket air filter5Click the PCFC software Download button.6Open the zip folder.7Double-click the install file and follow the on-screen instructions to install the PCFCControl Center software. The PCFC Control Center software and maps will bestored in C:\Program Files\PCFC Control Center.8Return to the Downloads or Home page where you can enter the make, model, andyear of your bike to check for and download additional maps.LOADING ADDITIONAL MAPS1Connect the USB cable from the computer to the PCFC. Verify the cable is fullyseated in the PCFC.2Run the Control Center software by double-clicking the program icon installed onyour desktop or on your start menu.3Click Open Map File and select a map file.4Click Send Map. You can send the map to any of the ten map positions.ALTERING MAPS USING SOFTWAREThe values in the map represent a percentage of fuel change over stock. A value of 10 inthe map indicates at that throttle position and RPM range the vehicle will be 10% richerthan stock. If the value is -10, then it would be 10% leaner than stock. You have theability to fine tune your fuel curve by altering these values. The Control Center softwareallows a value of 250 to -100 in each cell.IFC22012.01www.powercommander.com2006-2014 Yamaha Stratoliner/Roadliner/2008-2013 Yamaha Raider - 2
FIG.A1Remove the main seat.2Remove the right hand cosmetic engine cover as shown in Figure A. There is abolt at the front and rear of this cover.3Lay the PCFC in the area of the ECU.4Route the PCFC harness underneath the seat latch plate and under the righthand side of the frame as shown in Figure B.5Route the PCFC harness above the cylinder head following the frame.6Route the PCFC harness behind the engine mount bracket as shown inFigure 2014 Yamaha Stratoliner/Roadliner/2008-2013 Yamaha Raider - 3
FIG.D7Unplug the white 3-pin connector and the clear 6-pin connector as shown inFigure D.These connectors are located behind the ignition coils and lead to the throttlebody.FIG.E8Attach the PCFC connectors to the throttle bodies and stock wiring harnessas shown in Figure E.9Remove the strap from the ECU and move the ECU out of the way to accessthe wires underneath.10Locate the white 2-pin connector that has a brown and black wire.11Remove the blank end of this connection as shown in Figure F.FIG.FIFC22012.01www.powercommander.com2006-2014 Yamaha Stratoliner/Roadliner/2008-2013 Yamaha Raider - 4
FIG.G12Attach the red wire from the PCFC to the stock wiring harness as shown inFigure G.13Reinstall the ECU back into its stock position.14Locate the stock ground. Follow the negative battery cable to the frame.15Remove the allen bolt securing the ground cable to the frame.16Reinstall the allen bolt through the stock ground cable then through the groundwire from the PCFC into the frame as shown in Figure H.17Using the supplied velcro, secure the PCFC on top of the ECU as shown inFigure I.FIG.HFIG.IMake sure to clean both surfaces with the alcohol swab before 14 Yamaha Stratoliner/Roadliner/2008-2013 Yamaha Raider - 5
FIG.J18Follow the wire harness from the O2 sensor to the connection behind theframe and disconnect it as shown in Figure J.19Connect the Dynojet O2 optimizer to the stock wiring harness.The O2 sensor does not need to be connected to anything at this time.20IFC22012.01www.powercommander.comReinstall the cover and the seat.2006-2014 Yamaha Stratoliner/Roadliner/2008-2013 Yamaha Raider - 6
2006-2008 Yamaha Roadliner/Stratoliner Stock exhaust Stock or aftermarket air filter Stock O2 sensor disconnected Position 2 2009-2014 Yamaha Roadliner/Stratoliner Stock exhaust Stock or aftermarket air filter Position 3 2008-2013 Yamaha
23.03.2009 3 Update to V6.4 of the ABRITES VAG Commander 2.8 21.04.2009 3 Update to V6.5 of the ABRITES VAG Commander. Procedures for Q7/A6/Allroad described 2.9 19.05.2009 2, 3, 7 Update to V6.6 of the ABRITES Commander for VAG 2.10 25.05.2 3 Added descriptions 2.11 17.06.2009 All Update to V7.0 of the ABRITES Commander for VAG 2.12
a commander's decision making process that it directly affects the successful execution of operations. "13 These critical information requirements are determined by the commander to reduce this mass of information to those elements that are critical to the commander's ability to make decisions. By
Multi Commander Documentation. Multi Commander Documentation. Tab. installed) Button Panel. Multi Commander Documentation. files. Commander. .
configuration of the Storage Commander facility module. To learn more about using the Storage Commander Configuration Manager module, please refer to the Storage Commander Configurations Manager manual. Site Map The Site Map is a feature rich and extremely powerful feature of the Storage Commander V5 program. Read
Navy Region Japan (8/13) Ord'd as: Special Assistant to Commander, Naval Air Forces 125 Dixon R. Smith Commander, Navy Installations Command (10/14) 72 James G. Foggo III Commander, 6th Fleet (12/14) 73 Troy M. Shoemaker Commander, Naval Air Forces/ Commander, Naval Air Force, U.S. Pacific Fleet (1/15) 74 Margaret D. Klein Senior Advisor to the
Wing safety officer Support group commander Mission support squadron commander Communications squadron commander Civil engineer squadron commander Security police squadron commander A.Functional Requirements 1. Education Areas a. Seminar Room(s) - For student class work, case studies, and class exercises. b. Auditorium - Supports instructional
Rifle Platoon Billet Descriptions Platoon Commander The Rifle Platoon Commander carries out the orders of the Rifle Company Commander. He is proficient with all T/O weapons within his platoon. He ensures that the platoon is trained in accordance with Marine Corps standards and the company commander’s guidance. He is responsible for
Jun 14, 2019 · Force Recon from 1977-79 and commissioned through the MECEP program in 1982 as an Infantry Officer. He held the position of 81mm Mortar Platoon Commander (2/8), Rifle Company Commander (B 1/7), Infantry Bn Commander (3/2) and Infantry Regiment Commander (4th Marines).
