CAD & Drafting Manual For Signalling Drawings
Discipline:Engineering (Signalling)Category:ProcedureCAD & Drafting Manual forSignalling DrawingsESD-25-01ApplicabilityARTC Network Wide9CRIA (NSW CRN)9Primary SourceSCP 06, PP-117.4.3Document StatusVersionDate ReviewedPrepared byReviewed byEndorsedApproved1.213 August 2010StandardsStakeholdersChief OperatingOfficerRisk & SafetyCommittee09/06/2009Amendment RecordVersionDate ReviewedClause1.030 Apr 09First issue. Supersedes NSW Standard SCP 06 v1.3 in part1.107 Oct 09Disclaimer updated as per Risk & Safety Committee 14/09/20091.213 August 2010AllDescription of AmendmentIssued as final. Australian Rail Track Corporation Limited 2009Disclaimer:This document has been prepared by ARTC for internal use and may not be relied on by any other party without ARTC’s prior written consent. Useof this document shall be subject to the terms of the relevant contract with ARTC.ARTC and its employees shall have no liability to unauthorised users of the information for any loss, damage, cost or expense incurred or arising byreason of an unauthorised user using or relying upon the information in this document, whether caused by error, negligence, omission ormisrepresentation in this document.This document is uncontrolled when printed.Authorised users of this document should visit ARTC’s intranet or extranet (www.artc.com.au) to access the latest version of this document.
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsContentsContents1Introduction . 41.1Purpose . 41.2Scope. 41.3Signal Design File Structure. 41.4Setting up the CAD Environment . 41.5Definitions . 51.6Reference Documents . 51.7Documentation & Drawings . 61.8Labelling of Compact Disks . 61.9Code identification . 71.10 Symbols for Plans and Drawings. 81.11 MicroStation Title Block. 82Signalling Circuits – NSW Standards. 102.1General . 102.2Circuit Book Layout . 102.3Signal Circuit Drawing Format. 132.4Drawing Layers. 132.5Linework. 142.6Text . 142.7Master Sheet Blocks . 142.8Signalling Circuit Symbols . 142.9Plotting of Circuit Drawings . 152.10 Extended Sheets. 152.11 Circuit Continuation. 152.12 Filenames . 1634Version 1.2Signalling Plans . 183.1General . 183.2Overlapping . 183.3Drawing Scales . 183.4Centreline . 183.5Format for Signalling Plans . 18Track Insulation Plans . 214.1Scale. 214.2Per-way Plans. 214.3Format for track Insulation Plans. 21Date of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 2 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsContents567Detail Site Surveys. 225.1General . 225.2Detail Site Survey Drawing Format . 225.3Format . 23Drivers Diagrams & Weekly Notice Insertions . 246.1General . 246.2Layers . 246.3Size . 246.4Reduction . 246.5Title Block. 24Other Drawings. 257.1Equipment Housing . 257.2Level Crossings. 257.3Mechanical Drawings . 257.4Structures & drawings . 257.5Clearance Diagrams . 258Appendix 1: Signal Design Microstation Cell Libraries . 269Appendix 2: Signal Design Microstation Level Structure . 3110Appendix 3: Signal Design AutoCAD Circuit Block List – NSW Standards3310.1 Special Blocks for New & Removed Circuit Work . 4310.2 Special Blocks for Extended Sheets. 4311Appendix 4: Symbols for Plans & Drawings – NSW Standards . 4412Appendix 5: Drawing Template – ACAD.DWG. 5413Appendix 6: Symbols for Plans & Drawings – SA Standards. 5514Appendix 7: Signalling Symbols for Grade Predictors . 6314.1 Signalling Plan Symbols for Grade Predictors. 6314.2 Track Insulation Plan Symbols for Grade Predictors . 65Version 1.2Date of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 3 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsIntroduction1Introduction1.1PurposeThe purpose of this document is to describe the procedures and standards that must be adheredto for the production of signalling documentation & drawings for ARTC Network wide signallingprojects.1.2ScopeThis section of the manual is intended to address the production of CAD drawings associatedwith signalling works and to assist in: Standardise the preparation of drawings Simplify the various aspects of the work Provide guidance on detailing Secure consistency in quality and appearanceDrawings covering signals infrastructure in Victoria are to be in accordance with the agreedrequirements of the VicTrack Drawing Management System. Drawings covering infrastructure inSouth Australia and Western Australia will be in accordance with the symbols detailed inAppendix 6. By agreement with the respective signal maintenance engineer, these symbolsmay also be in New South Wales.If, in special cases or for particular clients, it becomes necessary to deviate from thesepractices, then the Signal Standards Engineer must first give approval. Any proposedpermanent change or alternative to these procedures must be circulated to Signal DesignSection staff for their comment and subsequent agreement. Changes shall be incorporated inthis Procedure.This section of the Manual also contains information and advice on the detailing of drawings.The use of this information should lead to the best and most economic solution of draftingproblems, (resulting in savings in time and effort) even when the drafting officer is not fullyfamiliar with the particular work.Corporation-wide standards are to be found in Section 1 of this manual, or in the AustralianStandard AS1100, parts 101 & 501. This section defines the standards to be applied to drawingsspecific to the Signal Design discipline. Generally, all drawings shall comply with AustralianStandards and any project specific special requirements.All references to Australian Standards refer to the latest edition.1.3Signal Design File StructureAll drawings, whether they are AutoCAD (dwg), MicroStation (dgn),XLS, PDF or TIF files mustonly be stored and worked on in the specified areas of the server. Local drives should not beused for working, storage or retrieval of any design files. This applies to both C: & H: drives ortheir equivalent.This reduces the risk of lost work or files due to equipment malfunction and removes thelikelihood of the duplicate drawing files existing outside the storage domain. This process alsotakes advantage of server backup operations.1.4Setting up the CAD EnvironmentTo maintain compatibility and transparency with the Railcorp draughting systems currently inuse throughout the ARTC alliance framework the AutoCAD environment structure & locationshould conform to a specific file structure.A ‘common’ directory is created within the working domain within which all AutoCAD relatedmenus, blocks and templates are to be located. Naming of the sub folders will be as describedVersion 1.2Date of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 4 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsIntroductionto maintain this compatibility without the need to modify menus and search paths within theAutoCAD setup, allowing seamless operation.DriveDirectorySub DirectoryFolderContentsX:/Common/ACADLt Resource/Analysis TemplatesCAD/EXCEL Sheets/BlocksAutoCAD-Blocks/Circuit Books/RegionAutoCAD Files/Drivers Diagrams/RegionAutoCAD Files/Locking Tables etc/RegionAutoCAD Files/Signalling Plans/RegionMicro station Files/Track Insulation/RegionMicro station FilesWithin these folders there will be a folder for that specific area e.g. Signalling Plans\Dubbo orDrivers Diagrams\Dubbo. This system is the same as used for Circuit Books.Then within each folder there is a sub-folder specific to each type of task:Designer - This folder is used for storage of any drawings produced or amended during thedesign process and can contain any number of other folders. It will be electronically secured forthe user, so he/she will be the only one who can alter the drawing and has total control of howthis area is used. Once the design is done, it can be used to store the drawings until theupdates are ready to commence. No work shall be done to this folder without consulting theoriginal owner. The CAD controller will always notify the designer about any changes via e-mail.Maintenance — This folder contains a current copy of the Original drawings & is used to updatethe drawings from the returned Master Testing Copies for maintenance updating. Once completeany updated files are copied back to the originals which shall be replaced by the latest version.This folder is then emptied.Originals — This folder is used to store original files for safekeeping. A backup CD may be alsokept as required.When all files have been updated & issued, new backup may be CDs burnt and drawing mastersreturned for storage.1.5DefinitionsDOCUMENTS AND DRAWINGSDocument and drawings shall be defined in the context of this manual as technical documentsand technical drawings relating to the infrastructure asset and its life cycle (specification,design, manufacture, construction, test and commission, operation, maintenance, modification,disposal) and shall not include documents or drawings relating to correspondence,administration, finance, marketing, human resource management, project management,contract management and the like.1.6Reference DocumentsThis Manual shall be read in conjunction with the Particular Specification, any general conditionsattached thereto and other specifications and documents comprising the Contract.In particular this Manual shall be read in conjunction with ARTC publications:Version 1.2 Signalling Design Principles ESD-05-01 Signalling Control Systems ESD-05-01, Signalling Circuit Design Standards SDS 25, Signalling Operator Interface, and Procedures.Date of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 5 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsIntroduction1.7Documentation & DrawingsAll documentation and drawings including those submitted for review, shall be in accordancewith this procedure, and laid out in a clear and logical fashion and shall be such as to facilitateunderstanding, checking, construction and maintenance.Current digitised Signalling & Track Insulation Plans are produced using Bentley MicroStation V8or later software. Circuit Diagrams, Detailed Site Survey Drawings, Drivers Diagrams, WeeklyNotice Insertions, Equipment Housing Plans are to be produced using AutoCAD software.New and amended plans plus other plans and drawings associated with signalling projects shallbe prepared using either MicroStation V8 or higher. New and amended circuit diagrams shall beprepared using AutoCAD LT2000 or AutoCAD 2000 or later version. All AutoCAD circuits shall besaved in AutoCADLt 2000 format, to be set as the default setting.Final digitised drawings shall be provided on write once Compact Discs.Documentation and drawings shall be prepared for A4 or A3 size paper and roll plans. Roll plansshall be divided into manageable and logical lengths and with height of 450mm wide (max.). A2and A1 size paper may be allowed for detailed mechanical and structural drawings.Geographically oriented drawings shall have the Sydney, or other main referenced localitydirection at the left hand side.Each design drawing including amended drawings shall be distinctively and uniquely identifiedas shall each controlled copy of a drawing.Each drawing shall include the names of the designer, checker and approver. Details shall beprovided for each amendment/issue of the drawing.1.8Labelling of Compact DisksCompact disks shall be labelled to allow easy identification of the contents. Where a number ofCDs are provided for a particular circuit book, each compact disc shall be labelled. The CD labelshall include the following details: Copy Purpose: eg Review Copy, Construction Copy, Test Copy, Commissioning Copy,Maintenance Copy Copy Name/No: eg Master Copy, Master Back Up Copy, Copy No. 1 Copy Holder: Name person issued to — responsible for Drawing Type: eg Signalling Plan, Track Insulation Plan, Circuit Book, etc. Drawing Name: eg Geographic location/area Job Name: as applicable or not Drawing Book/No: eg CB. or xxxxx Sheets No To (as applicable) Version No: Version Date: Disc No of Drawing Software: eg AutoCAD 2009 Lt Saved Drawing Format eg AutoCAD 2000Lt File No: (as applicable) Job No: (as applicable)Where several CDs are required for a circuit book the CDs shall be numbered as part of the set.By way of example, where 10 CDs are required for a circuit book the Compact Disc number shallbe in the following form: COMPACT DISC NO. 1 OF 10 etcAll CDs shall be supported by file lists.Version 1.2Date of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 6 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsIntroductionIn addition to the original copy a Backup copy of each drawing compact disc shall be provided.These backup copy CDs shall have detailed labels as provided on the original copy drawingcompact discs. Additionally, the Backup copy shall carry the name “BACKUP COPY DRAWINGS”.An example of a typical CD label is shown below:1.9Code identificationDrawings shall include the following Code Identification:Circuit Book Sheet:CCircuit Book Nos:Coded Sheet Numbering System000 – 999egA000 – Z000C087A025.dwgSignalling Plan / Track Plan:Four DigitsD1st DigitCircuit Book Nos:000 – 9991,2 Drawing in more thanone part.2nd/3rdDigite.g.D0450010.dgnTrack Insulation Plan:Est1 Digit0 drawing in one part10 1:1000 Scale11 Multi-scaleFour Digits1st Digit0 drawing in one part1,2 Drawing in more thanone part.2nd/3rd Digite.g.E0450010.dgn2nd/3rdDigit10 1:1000 Scale11 Multi-scaleIndicator Diagram:FVersion 1.2Circuit Book Nos:Fixed000 – 999010Date of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 7 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsIntroductionCircuit Book Sheet:e.g.F0610010.dgnDrivers Diagram:GArea Name in Characters:e.g.GHornsby.dwg/dgnMechanical Drawing:M1.10Five DigitsAcording to “numberingDrawings” codeforMechanicalSymbols for Plans and DrawingsSymbols for plans and drawings shall be in accordance with Appendix 4.1.11MicroStation Title BlockAll large format drawings shall include a title block. The title block shall be horizontal (as shownbelow) or vertical, where the two halves are placed side-by-side. Internally, the title blockinformation is filled in indirectly via a dialog box, opened from the bar menu. The information inthe right margin is automatically filled in at the time of plot/printout.Drawings shall include a template incorporating the following details:Version 1.2 ARTC name: Drawing Type: (e.g. Signalling Plan, Track Insulation Plan, Circuit Diagram, SignallingArrangements) Title of Drawing: (e.g. Project Name,Name, Process Name, Purpose Description) Purpose of Drawing: (Proposal, Construction, As-built) Drawing Number: Sheet/Part Number (where applicable): Version Date: Scale (where ate of last revision: 13 August 2010This document is uncontrolled when printed. See ARTC Intranet for latest version.Page 8 of 65
Engineering (Signalling) ProcedureESD-25-01 CAD & Drafting Manual for Signalling DrawingsIntroduction Legend (where applicable): Name of Organisation responsible for Drawing content For each amendment to the drawing the following details shall be included; Brief description of amendment: Version Number (Amendment): Version Date (Amendment): Na
Engineering (Signalling) Procedure ESD-25-01 CAD & Drafting Manual for Signalling Drawings Contents Version 1.2 Date of last revision: 13 August 2010 Page 3 of 65 This document is uncontr
Bruksanvisning för bilstereo . Bruksanvisning for bilstereo . Instrukcja obsługi samochodowego odtwarzacza stereo . Operating Instructions for Car Stereo . 610-104 . SV . Bruksanvisning i original
PART 1: Working With the CAD Standards Section 1. Purpose and scope of the CAD standards 1.1 Why WA DOC has data standards . 1.2 Scope of the CAD standards . 1. Who must use the standards? Section 2. CAD Environment 2. Basic CAD Software 1. CAD Application Software Section 3. Requesting CAD Data from WA DOC 2. How to request data Section 4.
Department of Civil Engineering AUST CE 102: Computer Aided Drafting Page 1 Chapter 1 Computer Aided Drafting (CAD) The use of computer technology for the process of design documentation (i.e. drafting). CAD may be used to draft in 2D or 3D space. 2D User Interface (AutoCAD 2007) Figure 1.1: 2D User Interface Drop Down Menu
10 tips och tricks för att lyckas med ert sap-projekt 20 SAPSANYTT 2/2015 De flesta projektledare känner säkert till Cobb’s paradox. Martin Cobb verkade som CIO för sekretariatet för Treasury Board of Canada 1995 då han ställde frågan
service i Norge och Finland drivs inom ramen för ett enskilt företag (NRK. 1 och Yleisradio), fin ns det i Sverige tre: Ett för tv (Sveriges Television , SVT ), ett för radio (Sveriges Radio , SR ) och ett för utbildnings program (Sveriges Utbildningsradio, UR, vilket till följd av sin begränsade storlek inte återfinns bland de 25 största
Hotell För hotell anges de tre klasserna A/B, C och D. Det betyder att den "normala" standarden C är acceptabel men att motiven för en högre standard är starka. Ljudklass C motsvarar de tidigare normkraven för hotell, ljudklass A/B motsvarar kraven för moderna hotell med hög standard och ljudklass D kan användas vid
LÄS NOGGRANT FÖLJANDE VILLKOR FÖR APPLE DEVELOPER PROGRAM LICENCE . Apple Developer Program License Agreement Syfte Du vill använda Apple-mjukvara (enligt definitionen nedan) för att utveckla en eller flera Applikationer (enligt definitionen nedan) för Apple-märkta produkter. . Applikationer som utvecklas för iOS-produkter, Apple .
Am I my Brother’s Keeper? Acts 15:19-35 Introduction: Since the beginning of time when the first man and woman rebelled against God, mankind has been separated from God. Every person since that time has been born into that rebellion and sin. Because of sin, people are separated from God and are unable to have a right relationship with Him or each other. Ill. of evil and suffering Inside of .
