INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.REMOVAL/INSTALL OF WINDOW REGULATOR (741-644)Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon,Chevrolet Silverado, GMC Sierra 2000–05General Tech Tips: Use painter’s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar. The replacement regulator should have a liberal amount of grease on slide area. If there is not much greasepresent, white lithium grease works well to lubricate the slide area. Aftermarket window tinting can cause the window to travel slower and put additional strain on the windowregulator assembly. Window run channels should be cleaned and lubricated before installation of a new window regulatorassembly. Silicone spray works well.PLEASE WEAR SAFETYGLASSES!Tools required for removal andinstallation of window regulator andmotor assembly: Phillips screwdriver Pry bar with flat end 7mm socket 10mm socket Socket wrench Wooden wedge or wide tape Cable cutter (if motor is immovable) Silicone spray lubricantDisclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.1
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.Removal InstructionsSTEP 1: Gain access to the window regulator assembly by removing the interior trimpanel.STEP 1a: Gently pry around plastic mirror trim piece and remove.STEP 1b: Gently pry around handle bezel and remove bezel.STEP 1c: Gently pry around switch and remove switch.STEP 1d: Disconnect electrical connections to switch.STEP 1e: Gently pry around door lock bezel and unsnap it from door panel. Unclip fromdoor lock rod and remove.STEP 1f: Using a 7mm socket, remove the 3highlighted screws.STEP 1g: Lift trim panel up and remove from door.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.2
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.STEP 2: With interior panel removed, peel back the plastic water barrier enough to beable to remove the regulator. Do not damage or discard plastic barrier, it will need to bereinstalled.STEP 3: Reconnect the window switch electrical connector.STEP 3a: If the window motor operates, move the window into a position where youcan access the 10mm bolts that hold the window guide clamps and go to step 5. If thewindow motor does not operate, go to step 4.STEP 4: Cut the window regulator cablewith a cable cutter so that you can manuallymove the window where you can access thewindow guide bolts.STEP 5: Loosen the 10mm window guidebolts enough so that the window can beseparated easily from the clamps. Do notremove the bolts or loosen all the way. Thewindow glass needs to be supported by theclamps until the glass is secured.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.3
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.STEP 6: Operate the switch or manuallypush the window into the full up position.Secure the window in place using a woodenor rubber wedge between the door frameand the window or simply tape the windowto the door frame. Be careful to use tapethat does not damage the paint on the doorframe.STEP 7: Disconnect the electrical plug fromthe window lift motor.STEP 8: Remove the six 10mm windowregulator mounting bolts that secure thewindow regulator to the door frame.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.4
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.STEP 9: Remove the right side track.STEP 10: Remove the left side track.STEP 11: The door is now ready for installation of the replacement part.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.5
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.Installation InstructionsSTEP 1: Loosen window guide clamp boltson replacement window regulator enoughfor clamps to easily slide over window glass.STEP 2: Install the left side track into thedoor.STEP 3: Install the right side track into thedoor.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.6
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.STEP 4: Move the window regulator into theproper position and line up the bolt holes.Install the 10mm bolts that were removedbut do not completely tighten. The boltsshould remain loose so that the regulatorcan be moved around for proper finalalignment.STEP 5: Reconnect the window lift motorelectrical plug.STEP 6: Remove tape or wedge from thewindow and door frame and lower windowinto the window guide clamps making surethat the window is correctly seated in theguides.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.7
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.STEP 7: Operate the window lift motor usingthe switch and send the window to thetop position making sure that it is alignedproperly in the window guide clamps andis parked properly at the top of its travel.Tighten the 10mm window clamp guidebolts evenly and torque to 9 N-m (80 lb in).STEP 8: Tighten the six 10mm regulatormounting bolts in the following order: BoltA, D, C, F, B, E. Tighten the bolts to 9 N-m (80lb in).STEP 9: Lubricate the window run channels.Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.8
741-644INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATORATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not havea service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay specialattention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.STEP 10: Operate the window up and down using the switch making sure that the glassmoves smoothly and is seated properly in the run channel.STEP 11: Disconnect the window switch.STEP 12: Reinstall the plastic water barrier making sure the wires are poking through thecorrect holes.STEP 13: Reinstall the interior trim panel.STEP 13a: Starting at the top of the door frame, hang the panel on the top lip and moveinto place making sure that the electrical wires are pushing through the proper holes inthe door panel. Make sure door handle is properly aligned with the hole in the door paneland that the door lock rod protrudes through correct hole in door panel.STEP 13b: Reinstall the three 7mm bolts that hold the panel to the door frame.STEP 13c: Reconnect window switch electrical plugs and snap switch into place on thedoor panel.STEP 13d: Maneuver handle bezel around door handle and snap into place.STEP 13e: Snap plastic mirror cover back into place.STEP 14: Perform a final operational check of window regulator assembly by operatingthe window up and down to ensure proper performance.We appreciate your opinions regarding this product!Please call our technical assistant with any challenges or suggestionsregarding the installation or operation of this product.1-800-523-2492Disclaimer:Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technicianbefore attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damageor personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic SafetyAdministration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. 2011 Dorman Products, Inc.No reproductions in whole or in part without prior written approval.9
INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR 741-644 Disclaimer: Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations.
SHIFT-F5. Change the window to a 3D Window SHIFT-F6. Change the window to an IPO Window SHIFT-F7. Change the window to a Buttons Window SHIFT-F8. Change the window to a Sequence Window SHIFT-F9. Change the window to an Outliner Window SHIFT-F10. Change the window to an Image Window SHIFT-F11. Change the window to a Text Window SHIFT-F12.
Saturable Current Transformers / Power Potential Transformers (SCT/PPT) regulator Brushless exciter regulator Direct current (dc) rotating exciter regulator In the SCT/PPT regulator and dc rotating exciter regulator applications, the EX2100e Regulator system can de-sensitize
Step 6 – Alternator Regulator Removal Note: These instructions are for the Isuzu/Lucas alternator fitted to my boat – yours may be different! This is a difficult part to remove as the bolts are a small size and inset into the top of the regulator. The bolts heads are 7/32” in size. The regulator is located in the bottom of this
6 Sekce katalogu – Elektronické regulátory O bjednací kódy Regulátor FX05 Regulátor Objednací kódy Regulátor FX05, 3 AI A99, 1 AI NTC, 5 DI, 6 DO relé, 1 AO, bez kom. karty, bez kabelu LP-FX05P11-002C Regulátor FX05, 3 AI A99, 1 A
AMD Rome CPU based yx5x servers Hot insertion Orderly removal Surprise removal Hot insertion Orderly removal Surprise removal Orderly removal Surprise removal Note: Linux upstream kernel v
WINDOW BROCHURE. 3 TABLE OF CONTENTS Step-by-Step Window Guide 3 Window Anatomy 4 Window Types 6 Window Performance 14 Passive House 17 PermafinishTM Colours 18 Grilles 20 . window design. AVAILABLE IN THE FOLLOWING FAMILIES: Supreme Select SELECT EXTERIOR SELECT INTERIOR WINDOW TYPES. 9
Seat Alhambra 96-06 V.W. Seat Leon 2009-On V.W. Sharon 1 Pc. Clips Window Regulator 13540PK 61mm Width 34.40mm Height 27.80mm Thick Right Front Door Window Regulator Clips Seat Alhambra 96-06 V.W. Seat Leon 2009-On V.W. Sharon 1 Pc. 13543PK 46.40mm Width 37mm Height 19mm Thick Window Regulator Clip, Front-Right (A-B), 2 Pcs Need. Audi A4 & B5 .
Analog-rich MCUs for mixed-signal applications Large portfolio available from NOW! 32.512KB Flash memory 32.128-pin packages Performance 170MHz Cortex-M4 coupled with 3x accelerators Rich and Advanced Integrated Analog ADC, DAC, Op-Amp, Comp. Safety and security focus
