Page 1 Of 13 Technical Service Bulletin
Page 1 of 13SB-10039588-6010Technical Service BulletinSUBJECT:ECM REPROGRAMMING FOR DTC P0016 orP0017: CRANKSHAFT/CAMSHAFT POSITIONCIRCULATE TO:[] GENERAL MANAGER[ X ] SERVICE ADVISOR[ X ] SERVICE MANAGER[No:TSB 12 13 002DATE:February, 2012MODEL:] PARTS MANAGER[ X ] WARRANTY PROCESSORSee below[ X ] TECHNICIAN[] SALES MANAGERThis bulletin supercedes TSB 11 13 008REVII, issued November, 2011, to clarify REQUIREDOPERATIONS and change their order. Changes are italicized and indicated by A.PURPOSESome affected vehicles may display an illuminated MIL with DTC P0016 Crankshaft/Camshaft IntakePosition or P0017 Crankshaft/Camshaft Exhaust Position Sensor Phase Problem, recorded in theECM. An incorrect parameter in the judgment criteria may cause mis detection of a fault withoutthere being an abnormal condition.This TSB provides dealers with a procedure to reprogram the ECM with new software to correct thecondition.IMPORTANT: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated and DTCsother than those described above are listed in the ECM memory (before reprogramming), diagnoseand repair those DTCs per the service manual before reprogramming. DO NOT reprogram the ECMuntil the reason(s) for other DTCs being set is corrected.AFFECTED VEHICLES2010 2011 Lancer Evolution built before January 27, 2011.2010 2011 Lancer/Lancer Sportback RAE built before January 27, 2011.2010 2011 Lancer/Lancer Sportback built before January 27, 2011.2010 2011 Outlander w/2.4L engine built before January 27, 2011.2011 Outlander Sport (RVR) built before January 27, 2011.REQUIRED OPERATIONS(3849)The information contained in this bulletin is subject to change. For the latest version of this document, go to the Mitsubishi Dealer Link,MEDIC, or the Mitsubishi Service Information website (www.mitsubishitechinfo.com).""ContinuedCopyright 2011, Mitsubishi Motors North America, Inc."OVERVIEWNOTE: MIL illumination may return if ALL steps of this procedure are not performed.1. Confirm MUT III software contains the latest reprogramming database.2. Reprogram the ECM with new software per the Reprogramming Procedure.3. Reset the Timing Chain Learned Value as described in Group 00 General — Timing ChainMaintenance, of the service manual.4. Perform “Erase and Read All DTCs.”5. Perform a test drive to confirm DTCs do not return.6. Correct any fault found during diagnosis including:a. Remove the MIVEC oil control valve(s) and inspect for foreign material.b. Remove the valve cover and check if the timing chain is out of position on the sprocket.For affected Lancer Evolution, Lancer RAE and Lancer Sportback RAE vehicles only.Pay special attention to visually check timing chain elongation (stretch) using procedures described"NOTE: This revision affects only written procedures in the OVERVIEW that follows. AffectedVehicles that were previously reprogrammed for this condition DO NOT requireadditional reprogramming, but may require additional inspections and repairs if theywere not previously completed.
Page 2 of 13TSB 12 13 002in Group 11A Engine — Timing Chain Elongation visual check. If the timing chain is stretched,replace it and the oil pump chain using procedures described in Group 11A Engine, of the servicemanual.The following equipment is needed to reprogram the ECM.D MEDIC laptop computer with A/C power adaptor 520924, or MIT547708.D VCI (Vehicle Communication Interface) MB991824.D MUT III main harness ’A’ (blue DLC connector) MB991910.D USB 2.0 cable MB991827.D “Engine Compartment/Control Module” label p/n MSSF024G00.D Reprogramming Database N11101 or higherD MEDIC 3 update at 085 or higher.D Standalone MUT III laptop with Reprogramming CD 2/11 installed.ECM REPROGRAMMING CHARTMODELMODEL YEAR 2010(TC* Turbocharged)CURRENTPART NO.DATA NO.10 Lancer Evolution4B11 TC* 5M/T1860B30610 Lancer Evolution4B11 TC* TC/SSTDISPLAY ON MUT III AFTERREPROGRAMMINGNew Part No.New S/W Part 3071860B3070210 Lancer/Lancer SportbackCALF 4B11 D4 VVT TC* TC SST1860B3081862B4441860B3081860B3080210 LancerCALF 4B11 D4 VVT MT1860B2951862B4211860B2951860B2950210 LancerCALF 4B11 D4 VVT CVT1860B2961862B4251860B2961860B2960210 LancerFED 4B11 D4 VVT MT1860B2971862B4241860B2971860B2970210 LancerFED 4B11 D4 VVT CVT1860B2981862B4261860B2981860B2980210 Lancer/Lancer SportbackCALF 4B12 D4 VVT MT1860B2991862B4271860B2991860B2990210 Lancer/Lancer SportbackFED 4B12 D4 VVT MT1860B3011862B4281860B3011860B3010210 Lancer/Lancer SportbackCALF 4B12 D4 VVT CVT1860B3001862B4291860B3001860B3000210 Lancer/Lancer SportbackFED 4B12 D4 VVT CVT1860B3021862B4301860B3021860B3020210 OutlanderCALIF (2WD) 4B12 D4 CVT1860B2471862B4221860B2471860B2470210 OutlanderCALIF (4WD) 4B12 D4 CVT1860B3031862B4231860B3031860B30301
Page 3 of 13TSB 12 13 002MODELMODEL YEAR 2011(TC* Turbocharged)CURRENTPART NO.DATA NO.11 NAS Lancer Evolution4B11 TC* 5M/T1860B47411 NAS Lancer Evolution4B11 TC* TC/SSTDISPLAY ON MUT III AFTERREPROGRAMMINGNew Part No.New S/W Part 4751860B4750311 Lancer/Lancer SportbackCALF 4B11 D4 VVT MT1860B3621862B4191860B3621860B3620411 Lancer/Lancer SportbackCALF 4B11 D4 VVT CVT1860B3631862B4201860B3631860B3630411 Lancer/Lancer SportbackFED 4B11 D4 VVT MT1860B3641862B4341860B3641860B3640311 Lancer/Lancer SportbackFED 4B11 D4 VVT CVT1860B3651862B4351860B3651860B3650411 Lancer/Lancer Sportback4B11 D4 VVT TC* TC SST1860B4851862B4461860B4851860B4850311 Lancer/Lancer SportbackCALF 4B12 D4 VVT MT1860B4561862B4361860B4561860B4560211 Lancer/Lancer SportbackFED 4B12 D4 VVT MT1860B4581862B4371860B4581860B4580211 Lancer/Lancer SportbackCALIF 4B12 D4 VVT CVT1860B4571862B4381860B4571860B4570211 Lancer/Lancer SportbackFED 4B12 D4 VVT CVT1860B4591862B4391860B4591860B4590211 Outlander Sport (RVR)CALF 4B11 D4 CVT1860B6371862B4181860B6371860B6370311 Outlander Sport (RVR)FED 4B11 D4 MT1860B6651862B4311860B6651860B6650211 Outlander Sport (RVR)FED 4B11 D4 CVT1860B6381862B4321860B6381860B6380311 OutlanderCALIF (4WD) 4B12 D4 CVT1860B4611862B4331860B4611860B46102
Page 4 of 13TSB 12 13 002REPAIR PROCEDURENOTE: Reprogramming the ECM with the latest database (i.e.11101) includes all past and currentreprogramming for TSBs of affected vehicles. You do not need to reprogram the ECM for eachTSB.1. Check the underside of the hood to verify there is no “Authorized Modification” label (see page 13 forexample) previously installed to indicate this reprogramming has already been completed. If a labelis present and the “ROM ID #” on the label matches the “New S/W Part No.” in the table above, theECM is at the latest level and reprogramming is not necessary. Conduct normal diagnosis for thesubject DTCs.For MEDIC 3 users only: (MUT III users go to step 5)2. Verify the MEDIC 3 is at version 3.1 and at update 085or higher.If your MEDIC 3 update is at least 085, continue withthe Reprogramming Procedure on page 6.If your MEDIC 3 update is below 085, update yourMEDIC 3 as follows.Version &Updatenumbers3. Select the MEDIC 3 Admin tab and click on “Updates.”AdminClick onUpdates
Page 5 of 13TSB 12 13 0024. If the MEDIC update screen advises updates areavailable, click the “Begin” button. After all updates arecomplete, GO TO THE REPROGRAMMINGPROCEDURE ON PAGE 6.Click “Begin”N11101NXXXXXX5. Standalone MUT III Scan Tool Viewer (STV) ONLY:(MEDIC 3 USERS go to the ProgrammingProcedure on page 6). Verify that your MUT III hasthe most current version of the reprogrammingdatabase:a. From the MUT III Main Page:DSelect “Special Function”DSelect “ECU Reprogramming”DSelect “Database File Display CAN”DConfirm the database number displayed at thetop right of the chart is N11101.(1) If the database number displayed on yourMUT III is N11101 or greater, continue to theReprogramming Procedure on page 6.(2) If the database number displayed on yourMUT III is lower than N11101, locate theYellow MUT III Reflash CD 02/11 and followthe instructions on the CD label to update yourMUT III.
Page 6 of 13TSB 12 13 002REPROGRAMMING PROCEDURECONNECT A BATTERY CHARGER TO THE VEHICLE’S BATTERY DURING THEREPROGRAMMING PROCEDURE. DO NOT ALLOW THE BATTERY CHARGER TO TIME OUT.BATTERY VOLTAGE (AS MEASURED AT THE BATTERY POSTS WITHOUT ELECTRICAL LOAD)MUST BE KEPT AT 12.4V OR HIGHER IN ORDER TO REPROGRAM THE ECM. MEASURE THEBATTERY VOLTAGE AND CHARGE AS NECESSARY.NOTE:VCI Stand alone reprogramming is not available for this procedure. The laptop andthe VCI must remain connected for the entire procedure.Connect the equipment as follows:USB CABLEVCI LAPTOPMEDIC II / MUT IIIMAIN HARNESSBLUE ENDVCIMEDIC 3 / MUT III LAPTOPDTurn the laptop computer on. If you’re running on battery power and the charge indicator in thelower right hand corner of the screen does not show a full charge, it is recommended that eitherthe laptop battery be charged prior to beginning, or that reprogramming be completed with the A/Cpower adaptor connected to the laptop.DConnect the USB cable to the VCI.DWhen the laptop displays the MUT III main screen, connect the USB cable to the laptop.DConnect the MUT III main harness with the blue DLC connection to the VCI.DConnect the blue connector of the MUT III main harness to the vehicle’s data link connector.DTurn the VCI power switch ON. Verify that the indicator lamp in the upper right corner of thescreen is green.CAUTIONDO NOT DISTURB THE HARNESS CABLES OR CONNECTIONS.INTERRUPTION DURING THE REPROGRAMMING PROCESS COULD CAUSETHE CONTROL UNIT TO LOSE DATA OR PREVENT FUTUREREPROGRAMMING. IF THE USB CABLE IS DISCONNECTED DURING THISPROCEDURE, A WARNING MESSAGE WILL DISPLAY.
Page 7 of 13TSB 12 13 002ECM Reprogramming1. Conduct the following steps to reprogram the ECM.a. Turn the ignition switch to the ON position. If the vehicle is equipped with the F.A.S.T. System,the transmitter must remain in the vehicle for the entire procedure.b. If using MEDIC 3, from the main page, click theMUT III STV icon at the top center of the screen.c. Select “Special Function.”d. Select “ECU reprogramming.”e. Select “Automatic Reprogramming (CAN).”
Page 8 of 13TSB 12 13 002f. Click on the car icon at the bottom of the page.g. If the VIN or vehicle description displayed does notmatch the vehicle you are working on, click on theeraser icon at the bottom of the page.Select VIN by clicking on the VIN button.h. Click on the icon in the lower RH corner of thescreen to have MUT III automatically read the VIN.If a message appears saying that the VIN cannot beinput automatically, manually type the 17 digit VINinto the VIN field at the top of the page.Make sure the VIN is correct and click on the checkmark.
Page 9 of 13TSB 12 13 002i. Confirm that all data matches the vehicle and clickthe check mark at the bottom of the page.j. MFI should be highlighted as the default. If not, clickon it to highlight it.Click on the check mark at the bottom of the page.k. A message will advise you that the system will“Automatic search the data.”Click on the check mark to continue.
Page 10 of 13TSB 12 13 002ECM TO LATEST VERSIONIf an “Complete Reprogramming” message does notappear, continue with step l.If this message is displayed, the ECM software isalready at the most current level. Do not continue withthis reprogramming procedure. This TSB does notapply.Click the check mark to clear the window, then click onthe Home icon at the lower left corner of the screen toreturn to the System Select main page.Turn off the ignition switch and disconnect the MUT III.Turn off and disconnect the battery charger. Conductnormal diagnosis.N11101l. The Automatic Reprogramming(CAN) databasescreen will display.NXXXXXXConfirm the database number at the top right of thetable is N11101 or higher.Data No.If more than one row is displayed in the table, referto the ECM Reprogramming Chart beginning onpage 2 to select the proper Data No. for thisprocedure and select the appropriate row.Click on the correct row to highlight it.Click on the check mark to continue.NXXXXXXm. A message will ask you to “Check reprogrammingdata.”n. Click on the check mark to begin reprogramming.It will take up to 5 minutes for reprogramming tocomplete.CAUTIONThe Daytime Running Lights and both the engine and condenser fans willautomatically be turned on during reprogramming. Care should be taken toinsure nothing gets caught in the moving blades. The radio will be turnedoff and you will also hear a chime in the interior for a short period of time.These are normal conditions.
Page 11 of 13TSB 12 13 0021860B3631860B036304o. This message will display when ECMreprogramming is successfully completed. Confirmthe “New S/W P/N” displayed matches the table atthe beginning of this TSB.p. You will be prompted to turn the ignition switch tothe OFF position, wait at least 8 seconds, then turnit back on.q. Click the check mark and you will be returned to the“ECU Reprogramming” page.2. Click the Home icon at the lower left corner of the pageto return to the MUT III main page.3. Using the MUT III, check and erase ALL DTCs from allsystems as follows.a. Select “Special Function.”b. Select “All DTCS,” then select “ERASE ANDREAD ALL DTCS.”
Page 12 of 13TSB 12 13 002c.The list on the left side of the screen will have allselections checked.Do not change theseselections. DTCs may be set if the vehicle isequipped with options that are unchecked.NOTE: The list on the RH side of the screenappears for Outlander Sport (RVR) andLancer based vehicles. For those models,the check mark at the bottom of the pageis not highlighted (inactive) at this time.d. If the check mark at the bottom of the screen ishighlighted, click it to proceed. If not proceed tostep e.e. In the left column, scroll to and clickFAST/IMMOB/KEYLESS/TPMS.In the rightcolumn, check the correct option code (VF#) fromthe Loading Options Setup list. This will activatethe check mark at the bottom of the page.f.DVehicles with regular keyless entry (buttons ona multi function key), select VF2.DVehicles with F.A.S.T. key, select VF3.In the left column, scroll to and select METER. Awindow will display. Check the correct display typefor the vehicle.Click the check mark to continue.4. A window will pop up asking you to confirm DTCerasing. Click the check mark for DTC erasing andreading to begin.5. When DTC erasing is completed, a window will pop up.a. If DTCs return after reprogramming, click thecheck mark to clear the window. Diagnose andrepair per the Service Manual.b. If DTCs do not return, click the check mark to clearthe window and then click the Home icon in thelower left of the screen to return to the main menu.6. Turn off the ignition switch and disconnect the MUT III.Turn off and disconnect the battery charger.
Page 13 of 13TSB 12 13 002"7. Using a ball point pen, enter the appropriate Engine Control Module (ECM) part number, SoftwarePart Number (ROM ID#), this Technical Service Bulletin number (TSB 12 13 002), your dealercode, and the current date on the Engine Compartment / Control Module Label (p/n MSSF024G00).The Vendor Code is not applicable. The label is available from your facing PDC."1860A306N/A1860B30602TSB 12 13 0029933212/15/12The Control Module Label is NOT used for this reflash. It should be discarded.8. Carefully remove all dirt and oil from a vacant area near the VECI label on the underside of the hood,and affix the Engine Compartment Label (LH side, above) to that area.9. Test drive the vehicle to confirm proper operation and that the MIL does not illuminate. Diagnose andcorrect any DTCs that return.PARTS INFORMATIONUse only the Genuine Mitsubishi Parts listed below.DescriptionModelPart NumberLabel, Engine CompartmentAllMSSF024G00WARRANTY INFORMATIONThis bulletin is supplied as technical information only and is not an authorization to repair. If anaffected vehicle is reported with the described condition, diagnose the condition, repair as describedin this bulletin and submit a normal warranty claim using the following information.ECM Reprogramming for DTC P0016 or P0017Nature Code: 91ZCause Code: 605Labor Operation No.: 138501 95Time Allowance: 0.3 hr.Warranty Coverage: Emissions Coverage Refer to the Superscreen for individual vehiclewarranty coverage terms.Special Warranty Information: Normal warranty procedures apply.
and repair those DTCs per the service manual before reprogramming. DO NOT reprogram the ECM until the reason(s) for other DTCs being set is corrected. AFFECTED VEHICLES 2010 2011 Lancer Evolution built before January 27, 2011. 2010 2011 Lancer/Lancer Sportback RAE built before January 27, 2011.
ef-fec1we issued by sandy valley water district ,-eb ri 7 '. ovh :- vi) hjj\j (name by -@- index page 1. page 2. page 3. page 4. page 5. page 6. page 7. page 8. page 9. page 10. page 1 1. page 12. page 13. page 14. page 15. page 16. page 17. page 18. page 19. page 20. .
The Lenape / English Dictionary Table of Contents A page 2 B page 10 C page 10 D page 11 E page 11 F no Lenape words that begin with F G page 14 H page 19 I page 20 J page 20 K page 21 L page 24 M page 28 N page 36 O page 43 P page 43 Q page 51 R no Lenape words that begin with R S page 51 T
Cahier pédagogique À deux roues, la vie! DynamO Théâtre 2 page 3 page 3 page 3 page 4 page 4 page 5 page 5 page 5 page 6 page 7 page 8 page 9 page 10 page 11 page 12 page 12
ÌSprue Bushing MSB-A3530 Page 18 Page 18 Page 18 Page 19 Page 19 Page 19 Page 20 Page 20 Page 20 Page 21 Page 21 Page 21 Page 22 Page 22 Page 22 Page 23 MSB-B3030 MSB-C2520 MSB-D3030 MSB-E2520 MSB-F1530 MSB-G3520 MSB-H3530 . HOT CHAMBER S L GP GB GPO EP C SB SP CL ML MAIN PRODUCTS ITEM
Trouble Shooting Safety Information INS-FM-30 . Remoter Control Operation Page 2 4 Page 5 6 Page 7 Page 8 Page 9 Page 10 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 18 Page 17 1 Warranty Service History Dealer Contact Information Page 20 .
Page 2 Econo-Form Overview Page 3 General Assembly Page 4 Panels Page 5 Channels & Fillers Page 6 Tube & Fittings Page 8 Corners Page 9 Push-Pull Props Page 10 Flex-Forms Page 11 Ties - Ferrule Type Page 12 Ties - Form Type Page 13 Ties - Dywidag Type Page 14 Ties - Water-Bar Type Page 15 Ties - Coil Type Page 17 Extractors Page 18 Climbing
Page 9 TM 886 TM 817 Page 9 TM 877 Page 9 TM 995 Page 9 TM 916 TM 937 TM 972 Page 12 TM 1300 — 1-3/4" Page 8 TM 1305 — 1-3/8" Rb3 Page 16 Rb4 CORneR b OCkS Page 19 wIndOw STOOl Page 7 R 6 Page 16 InTeRIOR JaMbS exTeRIOR JaMbS Page 18 TM 400 Page 8, 12 RadIuS CORneRS Page 19 PyRaMId CORneR blOCkS Page 19 TM 413 Page 12 TM
Set Manual Control Output and Brake Light Switches Initial Setup Test Drive & Adjustment Bench Test Troubleshooting Guide page 2 page 2 page 3 page 3 page 4 page 5 page 6 page 7 page 7 page 8 page 11 page 11 page 12 page 12 page 14 1. Drill 2. Drill bit, 5/16" 3. Phillips screwdriver 4. Pry tool TABLE OF CONTENTS CONTROLS & COMPONENTS TOOLS .
