Specification - S & C Electric
S&C Manual PME Pad-Mounted GearOutdoor Distribution (14.4 kV and 25 kV)SpecificationConditions of SaleSTANDARD: The seller’s standard conditions of sale setforth in Price Sheet 150 apply, except as modified under the“Warranty Qualifications” section on page 3.SPECIAL TO THIS PRODUCT:NOTE: S&C Manual PME Pad-Mounted Gear accommodatesseparable insulated connectors and accessories. This gearmust be operated by qualified persons who are thoroughlytrained in, and who understand any hazards that may beinvolved with, the operation of separable insulated connectorsand related accessories.INCLUSIONS: S&C Manual PME Pad-Mounted Gear featureselbow-connected encased components. Manual PME modelsare of freestanding, self-supporting construction—not forbolting directly to transformers—with provisions for cableentrance and exit through the bottom. Enclosures meet therequirements of ANSI C57.12.28 (enclosure integrity).Access to termination compartments is controlled by theS&C Penta-Latch Mechanism, which provides automaticdoor latching and permits padlocking only when the door issecurely latched. The door can be opened only with a pentahead socket wrench or tool.The enclosure roof is undercoated with an insulating “nodrip” compound. A resilient closed-cell gasket on the enclosure bottom flange protects the finish from being scratchedduring installation and isolates it from the alkalinity of aconcrete foundation. Enclosures are protected from corrosionby S&C’s olive green Ultradur Finishing System.Switch terminals are equipped with 600-ampere-ratedbushings, and fuse terminals are equipped with 200-ampererated bushing-wells. Bushing and bushing-well interfaces arein accordance with ANSI/IEEE Standard 386 to accept allstandard separable insulated connectors and inserts. Parkingstands are provided adjacent to each bushing and bushingwell. Grounding provisions suitable for use with separableinsulated connectors and related accessories are locatedin each termination compartment. Full-length steel barriers separate adjoining termination compartments (whereDecember 11, 2017 S&C Electric Company 1990-2017, all rights reservedapplicable). PME models are provided with an instructionmanual holder and storage racks on each fuse terminationcompartment door for spare S&C Fuse Units, Refill Units, orInterrupting Modules.All medium-voltage switch and fuse components are completely encased in an inner grounded steel compartment. Thecomponent compartment floor of 22-gauge galvanized steelsheet excludes foliage and animals. Fiberglass-reinforcedpolyester barriers are provided where required to achievepublished BIL ratings.Roof sections over the cable compartments are hinged toallow easy cable pulling during installation.External handle-operated 600-ampere S&C Mini-Rupter Switches provide three-pole live switching of three-phasesource circuits. A folding switch-operating handle, securedinside the switch-operating-hub pocket, is provided with eachMini-Rupter Switch.These PME models offer a choice of S&C Power Fuses—Types SME-20 and SME-4Z, or S&C Fault Fiter ElectronicPower Fuses. SME-20 Power Fuses use the S&C SMU-20 Fuse Unit, and SME-4Z Power Fuses use the S&C SM-4 Refill Unit. Fault Fiter Electronic Power Fuse Mountings alsoaccommodate a variety of single-barrel current-limiting fuses,as listed in Tables 12 and 13 on pages 13 and 14. Fuses providefault protection of the tap circuits, and loadbreak inserts andseparable insulated connectors supplied by the user permitsingle-pole switching of the taps. These units feature S&CTransFuser Mountings—fuse-handling mechanisms witha mechanical interlock that guards against gaining access tothe fuse before opening the loadbreak separable insulatedconnector at the fuse terminal. The fuse is accessible onlywhen de-energized and isolated—for full-view non-loadbreakdisconnection and removal with a shotgun stick.Individual ground rings are provided for each fusemounting to allow convenient grounding of cable concentricneutrals and elbow accessories. These ground rings are alsoequipped with cable guides to assist in cable training and toprevent cables from interfering with movement of the fuseaccess panel.Specification Bulletin 665-31
S&C Manual PME Pad-Mounted GearEXCLUSIONS: Three-phase units listed in Table 3 on pages4 through 6 do not include the items listed in Table 4 on page7, nor do they include the connector, fuse components, switchblades, or accessories listed in Table 2 on page 3; Tables 5, 6,and 7 on page 8; Table 14 on page 14; and Table 15 on page 15.SPECIFICATION DEVIATIONS: Features or modificationsother than those listed in Table 4 on page 7 cannot beaccommodated. Specifically, the following modifications arenot available: Relocation of components (switches and fuses) Inclusion of bracket- or base-mounted surge arresters orany type of cable-terminating device other than separableinsulated connectors Mechanical cable interlocksAPPLICATION NOTES: For application information as wellas a guide to the selection of appropriate ampere ratings andspeeds for S&C SME Power Fuses, and the types and TCCcurve parameters of control modules for S&C Fault FiterElectronic Power Fuses, contact the nearest S&C Sales Office.Switching with Mini-RupterS&C Manual PME Pad-Mounted Gear features S&C MiniRupter Switches for three-pole live switching of three-phasecircuits.Complete ratings for Mini-Rupter Switches, as applied inS&C Manual PME Pad-Mounted Gear, are shown Table 1. Inaddition to the load-dropping ratings shown, Mini-RupterSwitches are capable of interrupting transformer magnetizingcurrents associated with the applicable loads, as well as linecharging and cable-charging currents typical for distributionsystems of these voltage ratings. For applications on systemsrated higher than 7.2 kV and involving load current with highharmonic content (such as rectifier load currents), referto the nearest S&C Sales Office. The three-time duty-cyclefault-closing ratings shown for Mini-Rupter Switches definethe ability to close the switches three times against a threephase fault with asymmetrical current in at least one phaseequal to the rated value, with the switch remaining operableand able to carry and interrupt rated current.A Note on Single-Pole SwitchingIn using separable insulated connectors (elbows) for singlepole switching of three-phase transformers or transformerbanks (or single-phase transformers connected line-to-line)where the maximum system operating voltage exceeds 22kV, circuit connections or parameters may, in some cases,produce overvoltages that exceed the switching capabilityof the elbow. Therefore, follow the elbow manufacturer’srecommendations and the user’s operating and safetyprocedures for switching such transformers from other thanat the transformer location when they are unloaded or lightlyloaded.Recommended Voltage Ratings ofCurrent-Limiting Fuses for Use in S&CPad-Mounted GearIn general, current-limiting fuses should have a maximumvoltage rating equal to, but not greater than, 140% of thesystem line-to-line voltage because, for most applications,the fuses can be exposed to full system line-to-line voltagein clearing faults. Although there may be economic or spacesaving incentives for using current-limiting fuses with voltageratings “appropriate for system line-to-ground voltage” (i.e.,fuses with a voltage rating lower than line-to-line voltagebut greater than or equal to maximum system line-to-groundvoltage), S&C can recommend such use only in any of thefollowing applications: Protection of single-phase transformers serving singlephase loads Protection of three-phase lateral circuits fed by singleconductor shielded cable (provided each transformeron that lateral is individually fused so that the currentlimiting fuse serving the lateral will not be required toclear secondary faults) Protection of single-phase lateral circuits fed by singleconductor shielded cable where the load is line-to-groundconnectedTable 1. Ratings for S&C Mini-Rupter SwitchVoltage, kVLive SwitchingNom.MaxBILCont.Current, AmperesThree-Time Duty-Cycle Fault-ClosingShort-CircuitOne-SecondShort TimeWithstand,RMS, Sym.Load-Splitting(Parallel orLoop Switching)LoadDroppingPeakRMS, Sym.PeakWithstand,Peak14.417.59560060060065 00025 00065 00025 000252912560060060032 50012 50032 50012 5002 S&C Specification Bulletin 665-31
S&C Manual PME Pad-Mounted GearAchieving 25-kA Short-Circuit Rating in14.4-kV ModelsAs indicated in Table 3 on pages 4 through 6, specific 14.4-kVmodels have a short-circuit rating of 25,000 amperes, RMS,symmetrical and 620 MVA. They include: PME-4, PME-5, PME-6, PME-9, PME-11, and PME-12,furnished with Fault Fiter mountings, when certain nonS&C-manufactured current-limiting fuses are used, havinga rated maximum interrupting current of at least 25,000amperes, RMS, symmetrical and limiting the instantaneouspeak let-through current to less than 36,000 amperes (Referto Table 13 on page 14.) PME-10In each instance, separable connectors and cablesinstalled in the switch compartments must be rated 25,000amperes, RMS, symmetrical. In addition, the gear cannot be furnished with optional 200-ampere bushing wellsin lieu of 600-ampere bushings at the switch terminals,catalog number suffix “-M4,” or UL listing catalog numbersuffix “-X.”WARRANTY QUALIFICATIONS: The standard warrantycontained in the seller’s standard conditions of sale (as setforth in Price Sheet 150) does not apply to S&C ManualPME Pad-Mounted Gear where fuse units, fuse-unit endfittings, holders, refill units, or switch blades of other thanS&C manufacture are used in conjunction with S&C SMEMountings. Nor does it apply to S&C Manual PME PadMounted Gear where other than Fault Fiter Electronic PowerFuses, S&C Switch Blades, or the current-limiting fuses listedin Table 13 on page 14 are used in conjunction with Fault FiterElectronic Power Fuse Mountings and S&C Holders designedtherefore, or when current-limiting fuses are applied otherthan as set forth under the “Recommended Voltage Ratingsof Current-Limiting Fuses for Use in S&C Pad-Mounted Gear”section on page 2.How to Order1. Pad-Mounted Gear and Options(a) Obtain the catalog number of the desired unit fromTable 3 on pages 4 through 6.(b) Add suffix designations (to the catalog numberabove) to indicate the optional features desired,selected from Table 4 on page 7.(c) Connectors: Obtain the catalog number of theconnectors from Table 2.(d) Obtain the catalog numbers of accessories andtouch-up kit components from Tables 15 and 16 onpage 15.2. Fuse Components and Switch Blades(a) For SME-20 Power Fuses: Obtain the catalognumber of the end fittings and fuse units fromTables 5 and 8 on pages 8 through 10, taking care tomatch the voltage rating of the end fittings to thefuse units.(b) For SME-4Z Power Fuses: Obtain the catalognumber of the holder and refill units from Tables 6and 9 on pages 8 and 11, taking care to match thevoltage rating of the holder to the refill units.(c) For Fault Fiter Electronic Power Fuses: Obtain thecatalog number for the holders, the interruptingmodules, and the control modules from Tables 7, 10,11, and 12 on pages 8, 12, and 13, taking care tomatch the voltage rating of the holders, interruptingmodules, and the control modules.(d) For Switch Blades: Obtain the catalog number forthe switch blades from Table 14 on page 14.3. ExampleThe catalog number of a 14.4-kV manual Model PME-9with SME-20 Mountings with an optional fuse-storagefeature for three spare fuse holders or fuse units with endfittings in Compartment 1 is 65152R1-E1.Table 2. ConnectorBronze body, tin plated,two galvanized steel bolts,two Belleville washersNo. 2 solid (33.6 mm2) through 500 kc mil(335 mm2) stranded copper or aluminum4745S&C Specification Bulletin 665-31 3
S&C Manual PME Pad-Mounted GearTable 3. Three-Phase Units (Including mountings, less fuse components①)Model②andConnectionDiagram③PME-4 RatingsCurrent, Amperes, RMSkVFuseTypeShort-CircuitMVA3-PhaseCurrent, Amperes,Sym. atRMS, Sym.④RatedPadLoadMiniMainCont.Mounted VoltageDropping .(kgs.)Nom.MaxBILFuse,Max14.417.095200E ———14 00014 00035065102R1650(295)2527125200E ———12 50012 50054065103R1750(340)14.417.095200E———14 00012 50031065302R1650(295)2527125200E———12 50012 500 540 65303R1750(340)14.417.095200———14 00014 000 350 65502R1650(295)2529125200———12 50012 50054065503R1750(340)14.417.095200E 60060025 00014 00014 00035065112R1950(431)2527125200E 60060012 50012 50012 50054065113R11250(567)14.417.095200E60060025 00014 00012 50031065312R1950(431)2527125200E60060012 50012 50012 500 540 65313R11250(567)14.417.09520060060025 00014 00014 000 350 65512R1950(431)252912520060060012 50012 50012 50054065513R11250(567)14.417.095200E 60060025 00025 00014 00035065122R11700(771)2527125200E 60060012 50012 50012 50054065123R12125(964)14.417.095200E60060025 00025 00012 50031065322R11700(771)2527125200E60060012 50012 50012 500 540 65323R12125(964)14.417.09520060060025 00025 00014 000 350 65522R11700(771)252912520060060012 50012 50012 -5SME-20SME-4ZFaultFiter⑥SME-20PME-6 SME-4ZFaultFiter⑥① Fuse components must be ordered separately.② Vertical-type portable feed-thru inserts cannot be accommodated infuse-termination compartments of models furnished with SME-20 PowerFuses or Fault Fiter Electronic Power Fuses. Also, “piggybacked” Blackburn 600-ampere T-bodies cannot be accommodated in switch-terminationcompartments.③ Compartment numbers appear in corners of each connection diagram.④ Asymmetrical current rating is 1.6 times symmetrical current rating.⑤ Short-circuit rating of a complete pad-mounted gear unit may be limitedby the ratings of bushing inserts, elbows, T-bodies, fuses, and cables used.Fault-closing and/or short-circuit ratings of switches and bus, and its interrupting ratings of fuses, meet or exceed short-circuit rating of the gear. Forcomplete switch ratings, refer to the “Application Notes” section on page 2.⑥ Fault Fiter Mountings accommodate certain non-S&C-manufactured cur-rent-limiting fuses. Refer to Table 13 on page 14. The maximum voltage andcurrent ratings indicated in that table apply. Consult the fuse manufacturerfor complete fuse ratings.PageReferencefor DimensionalInformation161718 Available only when the end user is an electric utility. Optional key interlocks, catalog number suffix “-C3” or “-C4,” must befurnished if end user is not an electric utility. SMU-20 Fuse Units are available in ratings through 200K amperes aswell as 200E amperes. Applicable to solidly grounded-neutral systems only, with fuses connected by a single-conductor, concentric-neutral-type cable to a transformer(s). Rating is 9,400 amperes, RMS, symmetrical (405 MVA) for allother applications. 25,000 amperes, RMS, symmetrical and 620 MVA when certain nonS&C-manufactured current-limiting fuses are used, having a rated maximuminterrupting current of at least 25,000 amperes, RMS, symmetrical and limiting the instantaneous peak let-through current to less than 36,000 amperes.Refer to Table 13 on page 14. Separable connectors and cables installed inswitch compartments must be rated 25,000 amperes, RMS, symmetrical;gear cannot be furnished with optional 200-ampere bushing wells in lieu of600-ampere bushings at switch terminals, catalog number suffix “-M4,” oroptional UL Listing, catalog number suffix “-X.”TABLE CONTINUED 4 S&C Specification Bulletin 665-31
S&C Manual PME Pad-Mounted GearTable 3. Three-Phase Units (Including mountings, less fuse components①)—ContinuedRatingsCurrent, Amperes, RMSVoltage, kVModel②ConnectionDiagram③PME-9 FuseTypeShort-CircuitMVACurrent, Amperes,3-Phase CatalogRMS, Sym.④Sym. at ing 7.095200E 60060025 00025 00014 00035065152R11800(816)2527125200E 60060012 50012 50012 50054065153R12225(1009)14.417.095200E60060025 00025 00012 50031065352R11800(816)2527125200E60060012 50012 50012 500 540 65353R12225(1009)14.417.09520060060025 00025 00014 000 350 65552R11800(816)252912520060060012 50012 50012 50054065553R12225(1009)14.417.595—60060025 00025 00025 000 620 ageReferencefor 9125—600① Fuse components must be ordered separately.60012 50012 50012 50054065243R12450(1111)② Vertical-type portable feed-thru inserts cannot be accommodated in SMU-20 Fuse Units are available in ratings through 200K amperes aswell as 200E amperes.fuse-termination compartments of models furnished with SME-20 PowerFuses or Fault Fiter Electronic Power Fuses. Also, “piggybacked” Blackburn 600-ampere T-bodies cannot be accommodated in switch-terminationcompartments. Applicable to solidly grounded-neutral systems only, with fusesconnected by a single-conductor, concentric-neutral-type cable to atransformer(s). Rating is 9,400 amperes, RMS, symmetrical (405 MVA) forall other applications.③ Compartment numbers appear in the corners of each connectiondiagram.④ Asymmetrical current rating is 1.6 times symmetrical current rating.⑤ Short-circuit rating of complete pad-mounted gear unit may be limited byratings of bushing inserts, elbows, T-bodies, fuses, and cables used. Faultclosing and/or short-circuit ratings of switches and bus, and interrupting ratings of fuses meet or exceed short-circuit rating of the gear. For completeswitch ratings, refer to the “Application Notes” section on page 2.⑥ Fault Fiter Mountings accommodate certain non-S&C-manufactured cur-rent-limiting fuses. Refer to Table 13 on page 14. The maximum voltage andcurrent ratings indicated in that table apply. Consult the fuse manufacturerfor complete fuse ratings. Optional key interlocks, catalog number suffix “-C3” or “-C4,” must befurnished if end user is not an electric utility. 25,000 amperes, RMS, symmetrical and 620 MVA when certain nonS&C-manufactured current-limiting fuses are used, having a rated maximuminterrupting current of at least 25,000 amperes, RMS, symmetrical and limiting the instantaneous peak let-through current to less than 36,000 amperes.Refer to Table 13 on page 14. Separable connectors and cables installed inswitch compartments must be rated 25,000 amperes, RMS, symmetrical;gear cannot be furnished with optional 200-ampere bushing wells in lieu of600-ampere bushings at switch terminals, catalog number suffix “-M4,” oroptional UL Listing, catalog number suffix “-X.” To achieve this rating, separable connectors and cables installed inswitch compartments must be rated 25,000 amperes, RMS, symmetrical;gear cannot be furnished with optional 200-ampere bushing wells in lieu of600-ampere bushings at switch terminals, catalog number suffix “-M4.” Otherwise, gear is rated 14,000 amperes, RMS, symmetrical, and 350 MVA.TABLE CONTINUED S&C Specification Bulletin 665-31 5
S&C Manual PME Pad-Mounted GearTable 3. Three-Phase Units (Including mountings, less fuse components①)—ContinuedRatingsCurrent, Amperes, RMSVoltage, kVModel②ConnectionDiagram③PME-11 FuseTypeShort-CircuitMVACurrent, Amperes,Mini-Rupter3-Phase CatalogRMS, Sym.④Sym. at ing RupterBusGear⑤Nom.MaxBILFuse,Max14.417.095200E 60060025 00025 00014 00035065162R11900(862)2527125200E 60060012 50012 50012 50054065163R12375(1077)14.417.095200E60060025 00025 00012 50031065362R11900(862)2527125200E60060012 50012 50012 500 540 65363R12375(1077)14.417.09520060060025 00025 00014 000 350 65562R11900(862)252912520060060012 50012 50012 50054065563R12375(1077)14.417.095200E 60060025 00014 00014 00035065172R11725(782)2527125200E 60060012 50012 50012 50054065173R12150(975)14.417.095200E60060025 00014 00012 50031065372R11725(782)2527125200E60060012 50012 50012 500 540 65373R12150(975)14.417.09520060060025 00014 00014 000 350 65572R11725(782)252912520060060012 50012 50012 -12 SME-20SME-4ZFaultFiter⑥NetWt.,Lbs.(kgs.)① Fuse components must be ordered separately.② Vertical-type portable feed-thru inserts cannot be accommodated infuse-termination compartments of models furnished with SME-20 PowerFuses or Fault Fiter Electronic Power Fuses. Also, “piggybacked” Blackburn 600-ampere T-bodies cannot be accommodated in switch-terminationcompartments.③ Compartment numbers appear in the corners of each connectiondiagram.④ Asymmetrical current rating is 1.6 times symmetrical current rating.⑤ Short-circuit rating of complete pad-mounted gear unit may be limited byratings of bushing inserts, elbows, T-bodies, fuses, and cables used. Faultclosing and/or short-circuit ratings of switches and bus, and interrupting ratings of fuses meet or exceed short-circuit rating of the gear. For completeswitch ratings, refer to the “Application Notes” section on page 2.⑥ Fault Fiter Mountings accommodate certain non-S&C-manufactured cur-rent-limiting fuses. Refer to Table 13 on page 14. The maximum voltage andcurrent ratings indicated in that table apply. Consult the fuse manufacturerfor complete fuse ratings.6 S&C Specification Bulletin 665-31PageReferencefor DimensionalInformation2122 Optional key interlocks, catalog number suffix “-C3” or “-C4,” must befurnished if end user is not an electric utility. SMU-20 Fuse Units are available in ratings through 200K amperes aswell as 200E amperes. Applicable to solidly grounded-neutral systems only, with fusesconnected by a single-conductor, concentric-neutral-type cable to atransformer(s). Rating is 9,400 amperes, RMS, symmetrical (405 MVA) forall other applications. 25,000 amperes, RMS, symmetrical and 620 MVA when certain nonS&C-manufactured current-limiting fuses are used, having a rated maximuminterrupting current of at least 25,000 amperes, RMS, symmetrical and limiting the instantaneous peak let-through current to less than 36,000 amperes.Refer to Table 13 on page 14. Separable connectors and cables installed inswitch compartments must be rated 25,000 amperes, RMS, symmetrical;gear cannot be furnished with optional 200-ampere bushing wells in lieu of600-ampere bushings at switch terminals, catalog number suffix “-M4,” oroptional UL Listing, catalog number suffix “-X.”
S&C Manual PME Pad-Mounted GearTable 4. Optional FeaturesSuffix tobe Addedto PadMountedGearCatalog No.ItemLight gray outdoor Ultradur Finish instead of olive greenApplicable to Models-A2All modelsEquipment green outdoor Ultradur Finish (Toronto standard) instead of olive green-A3All modelsSeafoam green outdoor Ultradur Finish instead of olive green-A4All modelsSpecial color outdoor Ultradur Finish instead of olive green-A5All modelsWith olive green outdoor Ultradur Finish-A10All modelsWith light gray outdoor Ultradur Finish-A12All modelsWith special color Outdoor Ultradur Finish-A15All models-B1 All models-B2 All models except PME-4Stainless-Steel Enclosure①Hexhead actuator for use in lieu of pentahead actuator For use except when option suffix “-F2” is specifiedon all Penta-Latch MechanismsFor use when option suffix “-F2” is also specifiedKey Interlocks to prevent paralleling of switches in Compartments 1 and 2②-C1PME-6, -9, -10, -11Key interlocks to prevent opening fuse termination-compartment doors unless all switches are locked open②-C3PME-5, -6, -9, -11, -12Key Interlocks. Combines functions of options “-C1” and “-C3” above②-C4PME-6, -9, -11Located in Compartment 1-E1PME-4, -5, -6, -9, -11Located in Compartment 2-E2PME-6, -9, -11, -12Located in Compartments 1 and 2-E3PME-6, -9, -11-F1PME-5, -6, -9, -10, -11, -12-F2 PME-5, -6, -9, -10, -11, -12Fuse-storage feature for three spare fuse assembliesper compartment③Mounting provisions for a fault indicator in each switch Without viewing window in doorcompartmentNote: Accommodates three-phase indicator withWith viewing window in doorsingle-phase sensorsBase adapter, to permit a PME model to be installedon a mounting pad having anchor bolts located to suitthe comparable PMH model. This adapter increasesthe height of the unit 6 inches-KAll models-K10All modelsCarbon steel-K7All modelsStainless steel-K17All modelsCarbon steel-K8All modelsStainless steel-K18All models-L71All models600-ampere bushings without studs, at switch terminals-M1PME-5, -6, -9, -10, -11, -12200-ampere bushings wells in lieu of 600-ampere bushings, at switch terminals⑤-M4PME-5, -6, -9, -10, -11, -12UL listing. Includes “UL Listed” symbol on ratings label and nameplate⑥-X All 14.4-kV modelsBase spacer 6-inch (152 mm)Base Spacer 12-inch (305 mm)Carbon steelStainless steelInternational Crating④① When this optional feature is specified, the entire exterior of the enclo-⑤ When catalog number suffix “-M4” is specified, the continuoussure will be fabricated from 11-gauge Type 304 stainless steel. When ordering optional hexhead actuators, provisions for fault indicators with viewingwindows in doors, or a base adapter, specify the correct suffix for use with astainless steel enclosure.current and short-circuit ratings are limited to the ratings of the bushingwells, bushing inserts, and elbows used. In addition, the pad-mounted gearwill not be capable of carrying a 25,000 amperes, RMS, symmetrical shortcircuit rating and a 620 MVA rating.② When ordering, please furnish the name of ultimate user, station, and⑥ When catalog number suffix “-X” is specified, the pad-mounted gear willlocation of gear.③ Fuse assemblies (fuse holders or fuse units with end fittings) are notnot be capable of carrying a 25,000 amperes, RMS, symmetrical short-circuit rating and a 620 MVA rating.included. For units equipped with Fault Fiter Electronic Power Fuse Mountings, only two spare Fault Fiter Electronic Power Fuse Holders or two sparecurrent-limiting fuse holders can be accommodated in each compartment. When ordering catalog number suffix “-B1,” “-B2,” or “-F2” for use witha stainless steel enclosure, specify catalog number suffix “-B11” instead of“-B1,” “-B12” instead of “-B2,” or “-F12” instead of “-F2.”④ Choosing this option signifies that wood products to be used in the pack-aging of any items on international orders must either be hard wood or certified by the wood supplier as having “been heat treated (kiln dried) to a coretemperature of 56 Celsius for a minimum of 30 minutes.” Not available if UL listing (catalog number suffix “-X”) is specified. Not available if hexhead actuator for use in lieu of pentahead actuatoron all Penta-Latch Mechanisms (catalog number suffix “-B1,” “-B2,” “-B11,”or “-B12”) is specified.S&C Specification Bulletin 665-31 7
S&C Manual PME Pad-Mounted GearTable 5. SME-20 Power Fuse ComponentsFuse-Unit End FittingsItemCatalog NumberEnd fittings (including silencer), for use with SMU-20 Fuse Units3093SMU-20 Fuse Units①14.4 kV Nominal, 17.0 kV Max25 kV Nominal, 27 kV MaxFor a complete listing of available ampere ratings, speeds, and catalog numbers, refer to Table 8 pages 9 and 10.① These fuse units are usable in SM-20, SMD-20, SML-20, and SME-20Mountings.Table 6. SME-4Z Power Fuse ComponentsHoldersRatingItemkVHolder (including silencer), for use with SM-4 Refill UnitsCatalog 0363SM-4 Refill Units①14.4 kV Nominal, 17.0 kV Max25 kV Nominal, 27 kV MaxFor a complete listing of available ampere ratings, speeds, and catalog numbers, refer to Table 9 page 11.① These refill units are usable in SM-4, SM-4Z, SML-4Z, and SME-4ZHolders.Table 7. Fault Fiter Electronic Power Fuse ComponentsHoldersRatingItemkVHolder, for use with Fault Fiter Electronic Power 92003133Interrupting Modules①RatingItemInterrupting module, for use with Fault Fiter Electronic Power FuseskVMaxAmperes,Cont.Catalog l Modules ①For a complete listing of available types, TCC curve parameters, and catalog numbers, refer to Tables 10, 11, and 12 pages 12 and 13.① Interrupting modules and control modules rated 600 amperes con-tinuous are also applicable for use in mountings rated 200 amperescontinuous.8 S&C Specification Bulletin 665-31
S&C Manual PME Pad-Mounted GearTable 8. SMU-20 Fuse Units (For use in SM-20, SME-20, or SML-20 Mountings)①14.4 kV Nominal, 17.0 kV Max“K” RatingsRatings,AmperesSpeed“E” RatingsCatalog NumberS&C “K”TCC 165-2Rating,AmperesSpeed1SpeedCatalog NumberS&C Std.TCC 115-2702001S&C Std.TCC 201010E61201012K70201213E612013S&C SlowTCC 020S&C Very SlowTCC 0602200① These fuse units are equally suitable for use in SMD-20 outdoordistribution mountings.S&C Specification Bulletin 665-31 9
S&C Manual PME Pad-Mounted GearTable 8. SMU-20 Fuse Units (For use in SM-20, SME-20, or SML-20 Mountings)① —Continued25 kV Nominal, 27 kV Max②“K” RatingsRatings,AmperesSpeed“E” RatingsRating,AmperesCatalog NumberS&C “K”TCC 5E150E175E200ECatalog NumberS&C Std.TCC 115-2703001S&C Std.TCC 153-2S&C SlowTCC 119-2S&C Very SlowTCC 080603100603125603150603175603200① These fuse units are equally suitable for use in SMD-20 outdoor② Also suitable for protection of single-phase-to-neutral circuits (linesdistribution mountings.or transformers) on 20
S&C Specification Bulletin 665-31 3 S&C anual ME a-Mounte ear Achieving 25-kA Short-Circuit Rating in 14.4-kV Models As indicated in Table 3 on pages 4 through 6, specific 14.4-kV models have a short-circuit rating of 25,000 amperes, RMS, symmetrical and 620 MVA. They i
duppattas - six electric bell - two electric fans - three electric hand dryer-two electric iron - one electric lamps / wall-six electric organ-one electric shavers-two electric table lamp-two electric toaster-one empty receptacle
However, electric furnaces can accommodate central cooling easier than zonal electric heating, because the air conditioner can share the furnace’s ducts. Electric resistance heat can be provided by electric baseboard heaters, electric wall heaters, electric radiant heat, electric space heaters, electric f
HPKB Design Specification Document Data Mining Design Specification Document Non-Traditional Data Design Specification Document HMI Design Specification Document System Integration Design Specification Document 1.4. Software Design Specification Document Development Gui
Universal Serial Bus Revision 3.2 Specification Universal Serial Bus Revision 3.2 Specification. xxxx and xxxx xxxx and xxxx. Uni-versal Serial Bus Specification Universal Serial Bus Revision 3.2 Specification I2C-Bus Specification I2C-Bus Specification Sys-tem Management Bus Specification
Digital speed controller installation direction (left)*2 DR Digital speed controller installation direction (right)*2 G5 Designated grease specification NM Non-motor end specification PN PNP specification*1 TMD2 Split motor and controller power supply specification WA Battery-less absolute encoder specification WL Wireless communication specification WL2 Wireless axis operation specification
Independent Personal Pronouns Personal Pronouns in Hebrew Person, Gender, Number Singular Person, Gender, Number Plural 3ms (he, it) א ִוה 3mp (they) Sֵה ,הַָּ֫ ֵה 3fs (she, it) א O ה 3fp (they) Uֵה , הַָּ֫ ֵה 2ms (you) הָּ תַא2mp (you all) Sֶּ תַא 2fs (you) ְ תַא 2fp (you
This specification is to be applied in conjunction with the supporting data sheet, quality requirements specification (QRS) and information requirements specification (IRS) as follows. IOGP S-740: Specification for Batteries (IEC) This specification
Multi-Winch Shootout te Players h (in alphabetical order) Bulldog Alpha 9300 (9,300-lb electric) Engo E9000 (9,000-lb electric) Harbor Freight Badland 9000 (9,000-lb electric) Kodiak Bruin (9,500-lb electric) Summit Racing SUM-930002 (9,000-lb electric) Superwinch EP9.0 (9,500-lb electric) T-Max EWI9500 (9,500-lb electric) Warn 9.5xp (9,500-lb .
