Guide For Using DIRECTV SWM Technology With Winegard .

3y ago
28 Views
2 Downloads
838.52 KB
16 Pages
Last View : Today
Last Download : 2m ago
Upload by : Ronan Garica
Transcription

Guide for Using DIRECTV SWM Technologywith Winegard Mobile Satellite TV AntennasFor up-to-date information on receiver compatibility & programming,visit www.winegard.com/receivers2452242Rev6 4-14

Receivers Compatible with SWM TechnologyWinegard mobile satellite TV antennas that operate with Multi-switch technology require separate accessories tooperate with DIRECTV Single Wire Multi-switch (SWM) only technology receivers. For an up-to-date list of DIRECTVDVR and non-DVR receiver models that are only compatible with SWM technology, visit www.winegard.com/directv.This website also lists Winegard mobile satellite TV antennas that are compatible with DIRECTV. If unsure of yourreceiver model, check the back of the receiver or the inside front door of the smart card slot.Model numberSWM Kit PartsSWM8For proper SWM operation with Winegard satellite TV antennas that operatewith Multi-switch technology, the SWM8, DIRECTV PI-28 or PI-29 powersupply, and DIRECTV approved splitter (typically 2, 4, or 8 port) must be used.Failure to use this equipment may cause issues with your system. Note thatModel SK-SWM3 SWM TRAV’LER antenna operates with DIRECTV SWMtechnology without separate accessories.The DIRECTV power inserter PI-28 or PI-29 may damage a DIRECTV receiverif improperly connected in the system. The SWM output of the power insertershould never be directly applied to the input of a receiver. During installation,verify all wiring before applying power to the power inserter.PowerInserterSplitterCalculating Tuners for SWM InstallationDIRECTV SWM8 allows the use of up to eight tuners with a Winegard satellite antenna. Count the tuners in yourSWM installation to check that there are less than or equal to eight tuners being used with SWM8. Keep in mind thefollowing when counting the number of tuners: A non-DVR receiver counts as one tuner. A DVR receiver has dual tuners and counts as two tuners (even though only one coaxial cable is needed toconnect to a DVR receiver). The exceptions are the DIRECTV Genie and HR34 DVR receivers, which have fivetuners and count as five tuners when calculating tuners for a SWM installation.Number of non-DVR receivers 2 x Number of DVR receivers Total tuners for SWM8 installationMaximum of 8 non-DVR receiversMaximum of 4 DVR receiversTotal tuners 8 for SWM8 installationExampleTwo non-DVR receivers and three DVR receivers are being used for a SWM8 installation.2 non-DVR receivers 2 x 3 DVR receivers 8 total tuners for SWM installationWarnings 1Never use B-Band converters with SWM8.Do not use a DIRECTV PI-21 power inserter with a SWM8. Use a DIRECTV power inserter PI-28 or PI-29.Never power on all receivers at once. Sequentially power receivers since every receiver must get a SWM assignment.The power inserter must be installed inside the vehicle.

Winegard Mobile Satellite TV Antennas that RequireSeparate Accessories to Operate with SWM TechnologyAntennasSat 99 Sat 101 Sat 103 Sat 110 Sat 119 Wiring diagramSee page 3 for a SWM8installation, pages 7–10 foran SK-3005 combined with adome antenna***, or page 4for a SWM8 installation usingSWM1 & SWM2 outputs.See page 15 forreceiver settings.TRAV’LER SK-3005DIRECTV Slimline****See pages 11–12 for twowiring options for a SWM8installation or page 4 fora SWM8 installation usingSWM1 & SWM2 outputs. Seepage 15 for receiver settings.TRAV’LER SK-3003DIRECTV Triple LNB*See page 5 for a SWM8installation with domeantennas or page 4 for aSWM8 installation usingSWM1 & SWM2 outputs. Seepage 15 for receiver settings.Carryout automatic & G2,RoadTrip Mission &MiniMax , and DuraSAT *Carryout Anser *Carryout MP1 *See page 6 for a SWM8installation or page 4 fora SWM8 installation usingSWM1 & SWM2 outputs. Seepage 15 for receiver settings.See page 13 for a SWM8installation or page 4 fora SWM8 installation usingSWM1 & SWM2 outputs. Seepage 15 for receiver settings.See page 14 for a SWM8installation or page 4 fora SWM8 installation usingSWM1 & SWM2 outputs. Seepage 15 for receiver settings.Crank-ups,Dish & Tripod Kits(TR-6018, PM-2000)*DIRECTV primary 101 programming only. Toggling to alternate satellites is not supported.**Availability of channels on Satellites 110 and 119 is dependent upon the satellite port to which Port C of the TRAV’LER interface is connected.***Each antenna will see satellites as listed in the above table. Note that additional parts (not included) are needed for the combined setup of theTRAV’LER antenna and domed antenna with SWM technology.2

SK-3005 TRAV’LER Antenna with DIRECTV SWM8KEYCoaxial CablePower Cable(attached to power inserter)Less than 40 ft betweenantenna & SWM8For access to 99 /101 and 103 /110 /119 satellite programming, connect all four portsof the SK-3005 TRAV’LER antenna to all fourinputs on the SWM8.*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).3Terminate unusedsplitter outputswith a 75 ohmtermination cap.

DIRECTV SWM8 Using Both SWM1 & SWM2 OutputsThe wiring diagram below applies to all Winegard satellite TV antennas that require separate accessories to operatewith SWM technology. This wiring setup does not work with whole-home DVR setup. Model SK-3005 TRAV’LERantenna is shown below.KEYCoaxial CablePower Cable(attached to power inserter)Less than 40 ft betweenantenna & SWM8*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*Note: The splitter is not required in thisdiagram. The splitter would only berequired if using more than one receiveron either the SWM1 or SWM2 output.DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).Terminate unusedsplitter outputswith a 75 ohmtermination cap.4

Dome Antenna with DIRECTV SWM8The wiring diagram below applies to dome antennas, including the Carryout GM-1518 & GM-1599, Carryout G2,RoadTrip Mission & MiniMax, and DuraSAT antennas. The diagram applies to both stationary and tracking models.Model GM-1518 Carryout automatic antenna is shown below.If using an HD receiver with a dome antenna, change the preferences setting in the Display menu to “Hide all HDChannels.” Otherwise, the antenna will appear to not be working since the receiver guide will only show HD channels.Less than 40 ft betweenantenna & SWM8Terminate unusedSWM outputs with a 75ohm termination cap.For access to 101 satellite programming,connect the primary and secondaryports of the antenna to both SWM inputscorresponding to Satellite 99 /101 .KEYCoaxial CablePower Cable(attached to power inserter)*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).5Terminate unusedsplitter outputswith a 75 ohmtermination cap.

Carryout Anser Antenna with DIRECTV SWM8If using an HD receiver with the Anser antenna, change the preferences setting in the Display menu to “Hide all HDChannels.” Otherwise, the antenna will appear to not be working since the receiver guide will only show HD channels.Less than 40 ft betweenantenna & SWM8Terminate unusedSWM outputs with a 75ohm termination cap.For access to 101 satellite programming,connect the primary and secondaryports of the antenna to both SWM inputscorresponding to Satellite 99 /101 .KEYCoaxial CablePower Cable(attached to power inserter)*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).Terminate unusedsplitter outputswith a 75 ohmtermination cap.6

SK-3005 TRAV’LER Antenna with Dome AntennaWiring Version 1Set the Dish Type to 04: Slimline-5, and set the Switch Type to 01: SWM. For more information on receiver setupand complete step-by-step instructions, refer to your product manual, or go online to hen the receiver settings above are used with the SK-3005 TRAV’LER antenna, all HD and SD programming will beavailable. The same receiver settings will also work for the dome antenna but will display the “Searching for Signal”message on HD channels. To remove the “Searching for Signal” message, change the preferences setting in theDisplay menu to “Hide all HD Channels” when in dome operation. However, the receiver would need to be changedback to “Display All Channels” or “Hide All SD Duplicates” when changing back to TRAV’LER SK-3005 mode.NOTEIt may take several minutes for the DIRECTV receiver to load HD channels or to purge HD channels from thechannel guide.Terminate unusedSWM outputs with a 75ohm termination cap.A/B Switch (75 ohm) SpecificationsFrequency Range (DC): 2250 MHz.Current Capacity: 2AIsolation: 25 dBInsertion Loss: .25 dBReturn Loss: 11 dB or VSWR 2:1Only one A/B switch (not included) isrequired for operation. The A/B switchmust meet the specifications above.A/B SwitchSWITCH SETTINGS7ATRAV’LER AntennaBDome Antenna

KEYCoaxial CablePower Cable(attached to power inserter)*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*Terminate unusedsplitter outputswith a 75 ohmtermination cap.DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cableto the Satellite 2 input. With SWM, only connect to the Satellite1 port (labeled FTM or SWM).DCPowerPass8

SK-3005 TRAV’LER Antenna with Dome AntennaWiring Version 2Set the Dish Type to 04: Slimline-5, and set the Switch Type to 01: SWM. For more information on receiver setupand complete step-by-step instructions, refer to your product manual, or go online to hen the receiver settings above are used with the SK-3005 TRAV’LER antenna, all HD and SD programming will beavailable. The same receiver settings will also work for the dome antenna but will display the “Searching for Signal”message on HD channels. To remove the “Searching for Signal” message, change the preferences setting in theDisplay menu to “Hide all HD Channels” when in dome operation. However, the receiver would need to be changedback to “Display All Channels” or “Hide All SD Duplicates” when changing back to TRAV’LER SK-3005 mode.NOTEIt may take several minutes for the DIRECTV receiver to load HD channels or to purge HD channels from thechannel guide.KEYCoaxial CablePower Cable(attached to power inserter)9

A/B Switch (75 ohm) SpecificationsFrequency Range (DC): 2250 MHzCurrent Capacity: 2AIsolation: 25 dBInsertion Loss: .25 dBReturn Loss: 11 dB or VSWR 2:1Two A/B switches (not included) are requiredfor operation. The A/B switches must meet thespecifications above.A/B Switch #1SWITCH SETTINGSATRAV’LER AntennaBDome Antenna*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*A/B Switch #2Terminate unusedsplitter outputswith a 75 ohmtermination cap.DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cableto the Satellite 2 input. With SWM, only connect to the Satellite1 port (labeled FTM or SWM).DCPowerPass10

SK-3003 TRAV’LER Antenna with DIRECTV SWM8Wiring Version 1All three ports of the SK-3003 TRAV’LER antenna must be connected as shown tothree inputs on the SWM8 for access to 101 odd and even transponders, 119 oddtransponder only programming.Even (18V) transponders will not be available in Wiring Version 1.This will be verified in the receiver installation status screen shown to the right.KEYCoaxial CablePower Cable(attached to power inserter)Less than 40 ft betweenantenna & SWM8Terminate unusedSWM outputs with a 75ohm termination cap.*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).11Terminate unusedsplitter outputswith a 75 ohmtermination cap.

SK-3003 TRAV’LER Antenna with DIRECTV SWM8Wiring Version 2All three ports of the SK-3003 TRAV’LER antenna must be connected as shown tothree inputs on the SWM8 for access to 101 odd and even transponders, 110 and119 even transponder programming.Odd (13V) transponders will not be available in Wiring Version 2.This will be verified in the receiver installation status screen shown to the right.KEYCoaxial CablePower Cable(attached to power inserter)Less than 40 ft betweenantenna & SWM8Terminate unusedSWM outputs with a 75ohm termination cap.*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).Terminate unusedsplitter outputswith a 75 ohmtermination cap.12

Carryout MP1 Antenna with DIRECTV SWM8Less than 40 ft betweenantenna & SWM8Terminate unusedSWM outputs with a 75ohm termination cap.KEYFor access to 101 satellite programming,connect the primary and secondaryports of the antenna (located behindthe reflector) to both SWM inputscorresponding to Satellite 99 /101 .Coaxial CablePower Cable(attached to power inserter)*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).13Terminate unusedsplitter outputswith a 75 ohmtermination cap.

Crank-ups, Dish & Tripod Kits with DIRECTV SWM8The wiring diagram below applies to most portable dishes and tripod kits not already covered. The coaxial connectionports can be found at the base of the LNB for crank-up antennas, dish and tripod kits. For additional tips on connectingcoaxial cables to a crank-up antenna, see the back page. Toggling to alternate satellites is not supported.Less than 40 ft betweenantenna & SWM8Note: On a crank-up antenna, thecoaxial connection ports are locatedon the base of the LNB. To connecta coaxial cable to each port, it maybe necessary to remove the roller infront of the coaxial connection ports.For access to 101 satellite programming,connect the primary and secondaryports of the antenna to both SWM inputscorresponding to Satellite 99 /101 .Terminate unusedSWM outputs with a 75ohm termination cap.KEYCoaxial CablePower Cable(attached to power inserter)*Receivers in diagram can benon-DVR or DVR receivers.Non-DVR Receiver*DVR Receiver*If connecting to a DVR receiver, do not connect a coaxial cable to the Satellite 2input. With SWM, only connect to the Satellite 1 port (labeled FTM or SWM).Terminate unusedsplitter outputswith a 75 ohmtermination cap.14

DIRECTV Receiver SettingsReceiver settings are listed below for Winegard antennas using SWM technology. For more information onreceiver setup and complete step-by-step instructions, refer to your satellite TV antenna manual, or go online .SK-3005 TRAV’LER Antenna SettingsSet the Dish Type for 04: Slimline-5.Set the Switch Type for 01: SWM.Note that B-Band Converters should not be used with SWM Technology.SK-3003 TRAV’LER Antenna SettingsSet the Dish Type for 02: 3-LNB (18”x20”).Set the Switch Type for 01: SWM.Note that B-Band Converters should not be used with SWM Technology.Dome Antenna, Carryout Anser & MP1 Antenna,Crank-up Antenna, Dish & Tripod Kit SettingsSet the Dish Type for 01: Round (18”).Set the Switch Type for 01: SWM.Note that B-Band Converters should not be used with SWM Technology.www.winegard.com/mobileFor help, email help@winegard.com or call 1-800-788-4417Winegard Company 3000 Kirkwood St. Burlington, IA 52601-2000 800/788-4417 FAX 319/754-0787www.winegard.com Printed in U.S.A. 2012 Winegard Company Rev6 4/14 2452242Winegard, TRAV’LER, Carryout, Anser, RoadTrip, Mission, and DuraSAT are registered trademarks of Winegard Company, and MiniMax and MP1 aretrademarks of Winegard Company. DIRECTV is a registered trademark and Genie is a trademark of DIRECTV, LLC.Disclaimer: although every effort has been made to ensure that the information in this manual is correct and complete, no company shall be heldliable for any errors or omissions in this manual. Changes and technological advances are continuously being made in the satellite antenna market.Information provided in this manual was accurate at time of printing.15

The exceptions are the DIRECTV Genie and HR34 DVR receivers, which have five tuners and count as five tuners when calculating tuners for a SWM installation. Number of non-DVR receivers 2 x Number of DVR receivers Total tuners for SWM8 installation Example Two non-DVR receivers and three DVR receivers are being used for a SWM8 installation. 2 non-DVR receivers 2 x 3 DVR receivers 8 .

Related Documents:

FUTUREPROOF DIRECTV MULTISWITCHES SWM-30 DIGITAL SINGLE WIRE MULTISWITCH The SWM-30, also known as the DSWM30, is the current generation DIRECTV multiswitch, replacing the SWM-8, SWM-16, and SWM-32. With the correct receivers, it supports up to 30 tuners in two banks of 15 each. While this is fewer than the SWM-32, it actually supports

with Multi-switch technology, the SWM8, DIRECTV PI-28 or PI-29 power supply, and DIRECTV approved splitter (typically 2, 4, or 8 port) must be used. Failure to use this equipment may cause issues with your system. Note that Model SK-SWM3 SWM TRAV'LER antenna operates with DIRECTV SWM technology without separate accessories.

(e.g. H25 or HR34). If you have a SWM-only technology receiver, Winegard Model SWM-840 SWM kit is available. This SWM kit will allow for proper SWM technology operation with Winegard mobile satellite TV antennas. Supports up to two receivers Includes 25 ft power cable and 25

CONTROLLING YOUR DIRECTV RECEIVER The DIRECTV Universal Remote Control comes programmed to work with most DIRECTV Receivers. Should the remote control not work with your DIRECTV Receiver, you will need to set up the remote control by performing the following steps. Setting Up Your DIRECTV Remote 1. Locate the DIRECTV Receiver's brand and model

CONTROLLING YOUR DIRECTV RECEIVER The DIRECTV Universal Remote Control comes programmed to work with most DIRECTV Receivers. Should the remote control not work with your DIRECTV Receiver, you will need to set up the remote control by performing the following steps. Setting Up Your DIRECTV Remote 1. Locate the DIRECTV Receiver's brand and model

DIRECTV DSWM-30 MULTISWITCH DIRECTV’s last external multiswitch, the SWM-16, debuted in 2010. That’s a lifetime ago. Since then, DIRECTV and AT&T engineers have concentrated on developing multiswitch technology built right into the dish. New LNBs like the “3D2” and Reverse Band 3 provide up to 21 tuner capacity depending on the installation, and with that kind of power running through .

The DIRECTV Universal Remote Control is designed to give you access to features and functions found on your original remote control. To use it with your brand of DIRECTV Receiver, you will need to program the remote control by per-forming the following steps. Programming DIRECTV Remote 1. Locate the DIRECTV Receiver's brand and model num-

Client (RVU) Any RVU certified and DIRECTV approved device that can be connected to the DIRECTV Genie Server (e.g. TV’s, Blu-ray Players, etc.) DIRECTV RVU clients C31, C41, C41W, C51, C61K, C61W client non-DIRECTV RVU clients Samsung RVU TV, Sony RVU TV, PS3 etc. DECA (CCK) DIRECTV Et