TH 202 / TH 202-Ex Field Mounted HART Programmable, Pt

TH 202 / TH 202-ExField mountedtemperature transmitter,HART programmable,Pt 100 (RTD), thermocouples,electrical isolation10/11-8.64 EN Input––––Resistance thermometer (2, 3, 4-wire circuit)ThermocouplesResistance remote signalling unit (0.5000 Ω)Voltages, mV (–125.1200 mV) Output– 2-wire technique– 4.20 mA, HART signal Electrcal isolation (I/O))Digital low-drift processing of measurement valuesCustomer-specific linearizationContinuous sensor and self-monitoring– Parameter saved permanently in EEPROM– Monitoring of data integrety every 10 s– Substitution strategy in case of error (NE43) Approvals for explosion protection– intrinsically safeII 2 G EEx [ia] ib IIC T6, mount in zone 1–II 3 G EEx n A II T6, mount in zone 2– pressure-proofII 2 G EEx d IIC T6, mount in zone 1 Input functionality (absolute, differential, average value) EMC acc. to EN 50082-2 and NE 21 Parameterization– PC software application SMART VISION– Hand held terminals STT 04, HC 275– CoMeter (HART-Configurator/LC-Display) 5 years warranty

TH 202 / TH 202-ExField mounted temperature transmitter, HART programmable10/11-8.64 ENTechnical dataOutputInternal reference junctionOutput signal (temperature linear) 4.20 mAPt 100, via software switchable(no jumper necessary)Residual ripple (peak-to-peak) 0.2 %Power supplyCurrent consumption 3.6 mA(2-wire-methode: power supply wires signal wires))Max. output current23.6 mASupply voltage, poling protectedUs 8.5.30 V DCfor explosion protection application, max. Ui 8.5.29.4 V DCParameterizable current error signalUnderranging3.6 mAOverranging22 mADefault value3.6.22 mADampingt63 0.30 sInfluence of supply voltage 0.05 %/10 Vmax. residual ripple.Power demand of indicatorsInput(Power demand of transmitter and indicator have to be added.)ResistanceDigital indicatorResistance thermometer(IEC 751, JIS, SAMA)min. spanResistancemin. spann·Pt100/Ni100 toPt1000/Ni1000; Cu(n 0.1; 0.2; 0.5; 1; 1.2; 2; 3.10)15 K/50 KCoMeter(HART Configurator/LC-Display) Usd 2,9 V DCMaximale Load0.500 Ω / 0.5000 Ω5 Ω / 50 Ω( Usmax – Usmin )R ( k Ω ) ---------------------------------------------23, 6Max. line resistance (Rw) per core2, 3, 4-wire7.5 Ω, 10 Ω, 50 Ω300 µASensor short-circuit 5 Ω (for RTD)Sensor break 1.5 MΩInput filter50/60 HzThermocouplesTypesB, E, J, K, L, N, R, S, T, UVoltages–125 mV.125 mV–125 mV.1200 mVMin. span2 mV / 50 mVSensor monitoring current70 nAInput filter50/60 HzInput elementSensorThermocouple Type BThermocouple Type EThermocouple Type JThermocouple Type KThermocouple Type RThermocouple Type SThermocouple Type TThermocouple Type NDIN 43710Thermocouple Type LThermocouple Type UIEC 751; JIS; SAMA1)Resistance thermometer Pt 1002, 3 and 4-wireResistance thermometer Pt 1000DIN 437602)Resistance thermometer Ni 1002, 3 and 4-wireResistance thermometer Ni 500ResistanceΩVoltagemVStandardIEC 584-11)2)910Maximum permissible load RMeasuring currentUsd 2 V DC788ΩWith CoMetergennraiotrape(HC)250O08,5 11,4 14,4 17,3Z-20160Measuring range250. 1820 C ( 482. 3308 F)–250. 1000 C (–418. 1832 F)–210. 1200 C (–346. 2192 F)250. 1372 C (–418. 2502 F)– 50. 1768 C (– 58. 3215 F)– 50. 1768 C (– 58. 3215 F)–200. 1350 C (–328. 2462 F)–200. 1350 C (–328. 2462 F)–200. 900 C (–76. 482 F)–200. 600 C (–328. 1112 F)–200. 850 C (–328. 1562 F)–200. 850 C (–328. 1562 F)– 60. 250 C (–76. 482 F)– 60. 250 C (–76. 482 F)0.500 Ω / 0.5000 Ω–125 mV. 125 mV–125 mV. 1200 mVV DCPower supply Us30Min. measuring span235 C(423 F)30 C( 54 F)37 C( 67 F)54 C(98 F)171 C(308 F)193 C(348 F)50 C( 90 F)60 C(108 F)36 C( 65 F)40 C( 72 F)15 C( 28 F)50 C( 90 F)8 C( 15 F)15 C( 28 F)5 Ω / 50 Ω2 mV50 mVIEC 751 a 0.00385; JIS a 0,003916; SAMA a 0,003902Edison Curve No. 7Page 2 of 603.2000

TH 202 / TH 202-ExField mounted temperature transmitter, HART programmable10/11-8.64 ENTechnical dataGeneral characteristicsExplosion protectionResponse time 0.5 sVibration resistanceVibration in operationIntrinsically safeZone 12 g acc. to DIN IEC 68 part 2-6Electrical isolation (I/O)1.5 kV ACLong-term stability 0.1 % p.a.Environment conditionsAmbient temperature range–40.85 CII 2 G EEx [ia] ib IIC T6EC certificatePTB99 ATEX 2139 XTemperature class T6/T5/T4 50 C/65 C/85 CSupply circuitOutput [ib]Input [ia]Max. voltageUi 29.4 VUo 5.6 VShort-circuit current Ii 130 mAIo 145 mA3)Transport and storage temperature –40.100 CMax. powerPi 0.8 WPo 20 mWRelative humidity 100 %(100 % humidity with isolated terminals only)Internal inductanceLi 220 µHLo 1 mHcondensationInternal capacitance Ci 15 nFpermittedZone 2Mechanical constructionDimensionscf. dimensional drawingWeight1.25 kg (without accessories)Housing materialAluminium/stainless steelType of protectionIP 67Color (Epoxy)Co 1.55 µF3) Load current for connected primary element [ia] 1.5 mAlight grey (RAL 9002)II 3 G EEx n A II T6Conformity declarationPTB 99 ATEX 2216 XTemperature class T6/T5/T4 50 C/65 C/85 CPressure-proof enclosureII 2 G EEx d IIC T6EC certificatePTB 99 ATEX 1144 XTemperature class T6/T5/T4 50 C/65 C/85 CCanadian Standards Association and Factory Mutual 4)Electrical connection2 M20 x 1.5; 2 1/2“ GK2 1/2“ NPT; 2 3/4“ NPTThreador with cable screw connections2 pcs. M20 1,5 (metal)Ground screw ext./int.6 mm2 M5 / 2.5 mm2 M4Terminals, pluggable2.5 mm2, screw terminalsCharacteristics at rated conditions*)(acc. to IEC 770, related to 25 C)Measuring error incl. characteristic deviationPt 100/resistance measurement 0.2 % or 0.2 K/ 80 mΩwhichever value is greaterThermocouple/mV 0.2 % or 10 µVwhichever value is greaterAdditional influence of theinternal reference junction4) in preparationIntrinsically SafeFM/CSAClass I, Div.1/Div.2, Group A, B, C, D T6Class II, Div.1/Div.2, Group E, F, G T6Class IIIFMClass I, Zone 1, AEx [ia] ib IIC T6CSAClass I, Zone 1, Ex [ia] ib IIC T6NonincendiveFM/CSAClass I, Div.2, Group A, B, C, D, T6Class II, Div.1/Div. 2, Group E, F, G, T6Class T6ExplosionsproofFM/CSAClass I, Div.1/Div.1, Group A, B, C, D, T6Class II, Div.1/Div. 2, Group E, F, G, T6Class III T6InfluencesFlameproofFMClass I, Zone 1, AEx d IIC T6CSAClass I, Zone 1, Ex d IIC T6Influence effect of temperatureElectromagnetic compatibility (EMC)Pt 100/resistance measurement1)ME (Ω) (0.08 % 0.008 %) / 10KMS (Ω)Pt 100: measuring range 0.100 C, span 100 KPt 100 DIN IEC 751 cl. BClassThermocouple/mV2)ME (mV) (0.08 % MS (mV) 0.01 % 0.014 KMS (K) 100 %) / 10 KPercentage related to measuring span MS ME – MAMA lower range value, ME upper range value*) Percentagerelated to set measuring spanPt 100 (0.400 C): Effect of temperature influence (0.08 % 0.013 %)/10 K 0.093 %/10 K2)Type K (0.1000 C): Effect of temperature influence1)03.2000Type of testburst to signal/data linesstatic dischargecontact discharge to:contact plateterminals for supplyterminals for sensorsradiated field80 MHz.1 GHzcoupling150 kHz - 80 MHzDegree2 kVInfluence 0.5 %IEC1000-4-41000-4-28 kV6 kV3.75kV 1.0 % 1.0 % 1.0 %10 V/m 1.0 %10 V 1.0 %1000-4-31000-4-6Acc. to NAMUR NE 21 recommendationPage 3 of 6

TH 202 / TH 202-ExField mounted temperature transmitter, HART programmable10/11-8.64 ENDisplays (Option)Digital indicatorDigital display– LC display3½ digits ( 1999), digit height 10 mm, 7 segments– Standard scaling 0.100 %Linear scaling for measuring ranges and units possibleDescription of the physical unit (labels)CoMeter(HART Configurator)CoMeter (HART-Configurator/LC-Display)– 4 function keys for request and programming(Code protection)– LC display:5 digits ( 1999), digit height 7,6 mm, 7 segments– Sign and floating point– 10 segment bargraph (heading of measuring range)– 7 digits alphanumeric characters 6 mm, 14 segmentsRequest functionProcess variable, analog and display value, description of measuring point, serial number, error behaviour, lower/upper measuringrange limitChange functionDisplay mode (linear, average), physical unit, measuring range limits, damping, pass word, mains frequency filterDisplayResponse timeMeasuring errorOvervoltageDigitalConfigurator0,5 s1,3 s 0,1 % 0,15 %150 % of input215 mArangeEN 50082-2-20. 70 C0.100 %, condensation permittedEMCTemperatureHumidityMind limits of application.Special functionZero point adjustment, simulation of output signal, adjustment ofoutput signal, wet ToolParameterSMART VISIONSensor type, error signalling, measuring range,general characteristics (i. e. TAG number),damping, signal simulation of outputHand held terminal HHTSTT 04; HC 275ENEPASOUHERE(optional)PL OS IVEKECUEPGNDorHC 275, STT04Page 4 of 6orIsolatorsControllerRecorders (250 Ω min.)*Line resistanceEXIGHT WHE N CIRT E NS ION E N AT MOSPERUSCProcessinterfaceSO- VRRIABB 123.4 CFSKModem*if necessaryZ-20162L IVITSASoftware interface AMS, Cornerstone03.2000

TH 202 / TH 202-ExField mounted temperature transmitter, HART programmable10/11-8.64 ENOrdering informationCatalog NoTH 202 / TH 202-ExV11523(without expolsion protection)1TH 202With explosion protection:Type of protection: intrinsically safePTB / ATEXII 2 G EEx [ia] ib IIC T6(Zone 1) 5TH 202-Ex7FM / CSAClass I, Div. 1 / Div 2., Group A,B,C,DTH 202-ExClass II, Div. 1 / Div. 2, Group E,F,GClass IIIClass I, Zone 1, AEx [ia] ib IIC T6Class I, Zone 1, Ex [ia] ib IIC T6II 3 G EEx n A II T6(Zone 2) NTH 202-Ex N PTB / ATEXFM / CSAClass I, Div. 2, Group A,B,C,D, T6 nonincendiveClass II, Div. 2, Group E,F,G, T6Class III T6Type of protection: pressure-proof enclosure / explosion-proofII 2 G EEx d IIC T6DTH 202-Ex d PTB / ATEXEClass I, Div. 1 / Div. 2, Group A,B,C,D, T6TH 202-Ex d FM / CSAClass II, Div. 1/ Div. 2, Group E,F,G, T6Class III T6Type of protection: flameproofFClass 1, Zone 1, AEx d IIC T6TH 202-Ex d FMCSAClass 1, Zone 1, Ex d IIC T6Display / constructionAGLF housing without displayAGLFH housing (raised cover - 2 transmitters)AGLFD housing with digital indicatorAGLFD housing with CometerAluminiumMaterialStainless steelConnectionswith cable-screw-connection2 pieces: M 20 x 1.512 pieces: pressure-proof1Thread (without screw connection)M 20 x 1.51/2" NPT3/4" NPT1/2" GKMounting field housingwithoutWall mounting (STT 37)Wall mounting (stainlees steel)Pipe mounting (STT 37)Pipe mounting (stainless steel)ProgrammingFactory standard parameter:Pt 100, 4-wire circuit, damping off, direct action characteristicoverranging at sensor or device error (22 mA)Customer-specified parameter definitionwithoutCertificatesTwo-point calibration certificate9-point calibration certificate1metal-screw-connection EEx e bzw. EEx d (cable-diameter 3.5 8.7mm)DMLZ/deliv.3W748,00 *798,00 *798,00 *798,00 *798,00 *798,00 *798,00 *NHDC35,00 *299,00 *349,00 *AEa.A. / o. r. *MD123460,00 *75,00 *1234530,0055,0060,0095,00****SK40,00 *012140,00 *200,00 *AccessoriesCatalog NoDMH&B FSKMmdem [EEx ib] IIC (parameter setting in the installation)0343705618,00 *SMART-VISION5 Softwareon CD-ROM (German/English)7957777480,00 *on 3 1/2" diskettes (German/English) 7957778530,00 *SMART-VISION manualGerman795777950,00 *English50,00 *7957780TH 02 / -102 / -202 driver for AMS software 1.3.1 (Rosemount)7957771200,00 *5see Data Sheet 63-1.20Minimum hardware reuqirements: Intel 80486; 66 MHz, 8MB RAM; free hard-disk capacity; Windows 3.x (95, 98, NT)Notice: For a lokal programming on the desk can used as Hardware the universal TS02-Programming-Set (without Parasoft).(see Data Sheet 11-8.17 ordering information accessoriers )03.2000Page 5 of 6