Product Information Materials Testing Machines ZwickiLine .
CTA: 250043 42618Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0Touch Monitor with a zwickiLine materials testing machineApplicationzwickiLine is a powerful, flexible and cost-efficienttesting solution for a wide range of materials andcomponents. This materials testing machine is ideal forresearch and development, as well as routine qualityassurance testing.A wide range of equipment options enable use of thezwickiLine for tests on plastics, elastomers, metals,composites, paper, cardboard, textiles, foams, foodproducts and components for the medical engineeringand pharmaceutical industry.ZwickRoell zwickiLine materials testing machines canbe used in production and testing areas of cleanroomclasses 5 and 6. Cleanroom suitability of the materialstesting machines was validated according to DIN ENISO 14644 1:2016-06, DIN EN ISO 14644-14 and VDI2083-9.1.PI 396 0421Advantages and featuresErgonomic remote control with colordisplayTests can be performed entirely via thedisplay-equipped remote control, inde‐pendent of the PC. All important informationis shown on the color display. Machine oper‐ation is therefore more ergonomic and effec‐tive. Maximum operator safety is guaranteedwith the integrated Emergency stop. Therocker-switch with integrated dial makespositioning fast yet highly accurate.zwickiLine type TS, TN and THIntuitive and workflow-based from thevery startFrom the very start, users can easily andintuitively navigate testXpert III. testXpert IIIcontains a wide range of functionalities tomeet the requirements of different industries.With more than 600 prepared standard testprograms, the requirements of national andinternational test standards are guaranteedto be met. Master test programs, optionsand industry packages also offer the flexi‐bility to meet requirements in testing opera‐tions that go far beyond the standards.Modern, high-quality load-framedesign Scalable testing machine with two testareas guarantees optimal capacity utiliza‐tion, saving both time and money. The generous test area depth allows use oflarger fixtures and enables bigger compo‐nents to be tested, which are optimallysupported by the wide base crosshead. The new zwickiLine profile has six contin‐uous, freely accessible standard-profileslots for individual mounting of specimenmaterials, fixtures, safety devices, acces‐sories, etc. The zwickiLine can be operated in verticalor horizontal position as required, and canbe swiveled 180 in horizontal mode.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0testControl II machine electronicsand testXpert III testing software—apowerful combinationAll ZwickRoell materials testing machines areequipped with the powerful testControl IImeasurement and control electronics,offering the ideal basis for precise, reprodu‐cible test results.testXpert III testing software and testCon‐trol II machine electronics are perfectlymatched, ensuring safe and efficient opera‐tion of the testing system. testXpert IIIprovides the optimal solution for any testingrequirement.Flexibility Through ModularitytestControl II offers six flexible timesynchronized slots. These make it possibleto use multiple sensors at the same time,and can be monitored and protected irre‐spective of use. For example, an extensometer and a trans‐verse strain extensometer can be used inaddition to the load cell. If the testing system is equipped withseveral load cells or additional sensors,these can all remain plugged in. Allplugged-in sensors are automaticallyprotected against overloads.ZwickRoell Engineering—Made inGermanyThe development and manufacture of mate‐rials testing machines, including all mechan‐ical, electronic and software components,together with our comprehensive range ofaccessories, takes place at ZwickRoell'sproduction facility in Germany, enabling usto create a product that is perfectly harmon‐ized. Each materials testing machine ismade of the highest quality standardenabling ZwickRoell to offer the bestpossible support.Machine compliance correctionThe high-quality drive technology plus onlinecorrection of machine compliance enablevery high travel-measurement and posi‐tioning accuracy.Safety for the user and the entiretesting systemMaximum level of safety for user and testingsystem is guaranteed. All EC MachineryDirective safety requirements are fulfilled.The CE-compliant safety device with elec‐trical interlocking and mechanical guardlocking, transparent design and excellentaccessibility, protects the operator. Thehighest level of safety is achieved with thetwo-channel safety circuit.All data at ambient temperature.System monitoringtestControl II system monitoring provides theuser/laboratory manager with detailed infor‐mation on the current status and level ofutilization of the testing equipment. Thisenables further increases in testing equip‐ment availability and greatly simplifies main‐tenance planning and spares/replacementprocurement.Fast, adaptive drive controllerThe high drive control frequency of 1,000 Hzdelivers fast, precise force and strain control.Benefits include enabling components to beloaded very quickly and accurately with apredetermined force.Eco modeThe testControl II machine electronics auto‐matically switch to eco mode when not inuse, saving energy.We reserve the right to make technical changes in the course of ongoingdevelopment.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0CTA: 110410 165223Scale 622411Dimensions, TN testing systemCTA: 165223 42630Dimensions, TS testing system5316227511365104901589105531622Dimensions, TH testing systemAll data at ambient temperature.411Swivelable front safety device, with electrical interlockingWe reserve the right to make technical changes in the course of ongoingdevelopment.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0Technical dataGeneral technical data for zwickiLineLoad frameFinishA6-C31, RAL 7021 and RAL 3038Ambient temperature 10 . 35 CRelative humidity (non-condensing)20 . 90%ConformityISO 9000 and CEDrive systemMotorDC servo motorControl, set value preselectionDigitalControllerAdaptiveCycle time1000HzPositioning repeatability (without reversalof direction) 2μmDescriptionValueMachine electronicsNumber of available slots for measurement and control modules:Synchronized module slots2 (expandable to 5)1)Synchronized PCIe slots1Force measurementClass 0.5/1, depending on load cell, compliant toDIN EN ISO 7500-1, ASTM E4Measurement rangeUp to 165% of Fmax2)Calculated resolution (e.g., load cell in tensile/compressiondirection)24bitEffective resolution in tensile/compression direction:DCSC moduleUSC module1)2)19 bits (corresponds to 512,000 points)20 bits (corresponds to 1,000,000 points)Measured value recording rate400kHzMeasurement value transmission rate to PC500 (optional 2000)HzZero-point correctionAutomatic, at start of measurementMeasurement signal run-time correction for all channelsYesInterface to PCEthernetEco modeYes, automatic switch off of power section (time can be set)CE conformityYes, according to Machinery Directive 2006/42/ECA DCSC module is included in the scope of delivery (occupies one module slot). The drive requires an optional module slot.For load cells with Fmax 2.5 kN: up to 130% of FNDescriptionValuePower specificationsPower supply100 . 240V, 1Ph/N/PETolerance range 10%All data at ambient temperature.We reserve the right to make technical changes in the course of ongoingdevelopment.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0DescriptionValuePower consumption (full load), approx.500VAPower frequency50/60HzZ0.5TypeZ0.5 TSZ0.5 TNZ0.5 THItem No.058992058993058996Test load Fmax0.50.50.5kNMoving crosshead mounted with angleup235 . 5651)235 . 10651)235 . 13651)mmMoving crosshead mounted with angledown90 . 42090 . 92090 . 1220mmDepth105105105mmWidthNo limitationNo limitationNo limitationHeight without top Width with machine Depth with machine sshead speed vmin . vmax0.0005 . 20004)(optional 3000)5)0.0005 . 20004)(optional 3000)5)0.0005 . 20004)(optional 3000)5)mm/minDrive travel resolution0.08300.08300.0830μmTest areaHeight, Pmin Pmax (each without mount‐ing stud)Load frameDimensionsWeightWith machine electronics, approx.Average noise level at vmax measured at1 m distance from the front of themachineDrive system1)2)3)4)5)Height of the test area without accessoriesThe dimension increases by 9 mm with the additional crosshead option (top crosshead)With “large base” option: width 583 mm, width with machine electronics 585 mm, depth 565 mm, depth with machine electronics 707 mm.Values apply to machines with closed safety door and closed safety guard in automatic mode and to machines without safety device and/orwithout safety guard. For machines with the safety door and/or safety guard open, the speed is reduced to 600 mm/min.The speed can be increased to 3000 mm/min (optional).Z1.0TypeZ1.0 TSZ1.0 TNZ1.0 THItem No.058997058998058999Test load Fmax111kNTest areaAll data at ambient temperature.We reserve the right to make technical changes in the course of ongoingdevelopment.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0TypeZ1.0 TSZ1.0 TNZ1.0 THItem No.058997058998058999Moving crosshead mounted with angleup235 . 5651)235 . 10651)235 . 13651)mmMoving crosshead mounted with angledown90 . 42090 . 92090 . 1220mmDepth105105105mmWidthNo limitationNo limitationNo limitationHeight without top Width with machine Depth with machine sshead speed vmin . vmax0.0005 . 20004)0.0005 . 20004)0.0005 . 20004)mm/minDrive travel resolution0.05540.05540.0554μmHeight, Pmin Pmax (each without mount‐ing stud)Load frameDimensionsWeightWith machine electronics, approx.Average noise level at vmax measured at1 m distance from the front of themachineDrive system1)2)3)4)Height of the test area without accessoriesThe dimension increases by 9 mm with the additional crosshead option (top crosshead)With “large base” option: width 583 mm, width with machine electronics 585 mm, depth 565 mm, depth with machine electronics 707 mm.Values apply to machines with closed safety door and closed safety guard in automatic mode and to machines without safety device and/orwithout safety guard. For machines with the safety door and/or safety guard open, the speed is reduced to 600 mm/min.Z2.5TypeZ2.5 TSZ2.5 TNZ2.5 THItem No.059001059003059004Test load Fmax2.52.52.5kNMoving crosshead mounted with angleup235 . 5651)235 . 10651)235 . 13651)mmMoving crosshead mounted with angledown90 . 42090 . 92090 . 1220mmDepth105105105mmWidthNo limitationNo limitationNo limitationTest areaHeight, Pmin Pmax (each without mount‐ing stud)Load frameAll data at ambient temperature.We reserve the right to make technical changes in the course of ongoingdevelopment.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0TypeZ2.5 TSZ2.5 TNZ2.5 THItem No.059001059003059004Height without top Width with machine Depth with machine sshead speed vmin . vmax0.0005 . 10004)0.0005 . 10004)0.0005 . 10004)mm/minDrive travel h machine electronics, approx.Average noise level at vmax measured at1 m distance from the front of themachineDrive system1)2)3)4)Height of the test area without accessoriesThe dimension increases by 9 mm with the additional crosshead option (top crosshead)With “large base” option: width 583 mm, width with machine electronics 585 mm, depth 565 mm, depth with machine electronics 707 mm.Values apply to machines with closed safety door and closed safety guard in automatic mode and to machines without safety device and/orwithout safety guard. For machines with the safety door and/or safety guard open, the speed is reduced to 600 mm/min.Z5.0TypeZ5.0 TSZ5.0 TNZ5.0 THItem No.059005059006059007Test load Fmax555kNMoving crosshead mounted with angleup365 . 5401)365 . 10401)365 . 13401)mmMoving crosshead mounted with angledown125 . 300125 . 800125 . 1100mmDepth105105105mmWidthNo limitationNo limitationNo limitationHeight without top Width with machine Depth with machine electronics6223)6223)6223)mm707883kgTest areaHeight, Pmin Pmax (each without mount‐ing stud)Load frameDimensionsWeightWith machine electronics, approx.All data at ambient temperature.We reserve the right to make technical changes in the course of ongoingdevelopment.
Product InformationMaterials Testing Machines zwickiLine Z0.5 to Z5.0TypeZ5.0 TSZ5.0 TNZ5.0 THItem No.059005059006059007Average noise level at vmax measured at1 m distance from the front of themachine555555dB(A)Crosshead speed vmin . vmax0.0005 . 6000.0005 . 6000.0005 . 600mm/minDrive travel resolution0.01680.01680.0168μmDrive system1)2)3)Height of the test area without accessoriesThe dimension increases by 9 mm with the additional crosshead option (top crosshead)With “large base” option: width 583 mm, width with machine electronics 585 mm, depth 565 mm, depth with machine electronics 707 mm.All data at ambient temperature.We reserve the right to make technical changes in the course of ongoingdevelopment.
ISO 14644 1:2016-06, DIN EN ISO 14644-14 and VDI 2083-9.1. Advantages and features Ergonomic remote control with color display . 751 104 90 105 531 411 622 Dimensions, TS testing system 1289 1065 751 104 90 105 531 411 622 Dimensions, TN testin
7.1 Testing machines for quasi-static applications 24 7.2 Dynamic testing machines 26 7.3 System for testing at temperature and high temperatures 28 7.4 Testing machines for multi-axial stress states 29 7.5 Special testing systems and instruments 30 7.6. testXpert III testing software 32 7.7 Measurement and control electronics 34
Materials Testing Machine Introduction 2 012-13762D Materials Testing Machine (ME-8236). *See the PASCO catalog or web site at WWW.PASCO.COM Materials Testing System (ME-8230) The Materials Testing System includes the items in the Materials Testing Machine PLUS an interface, software, and sixty tensile samples as shown in Table 1.
fatigue testing machines, digital torque testing machines, multi-functional testing machines, grinding efficiency testers, run-out testers, digital measuring projectors, environmental testing chamber, grinding and polishing machines, infrared tachometers, vibrations testers and decibel
Product Catalogue GF Piping Systems. Contents Electrofusion units and accessories MSA machines Accessories Construction site machines Butt fusion machines Accessories Services Track & Trace Work shop machines Work shop machines Accessories Tools for installation of plastic pipes
Compression/Tension Testing Machines Perth: 0408 034 668 Melbourne: 0428 315 502 Sydney: 0418 381 709 Brisbane: 0419 477 715 www.pcte.com.au Manual Cement Compression and Flexure Testing Machines UTCM-6310/UTCM-6410 The UTCM-6310 and UTCM-6410 single and double testing chamber Manual compression and flexure testing
Tools and machines Worksheet 6.1 Simple machines 1. Complete the sentences. tools one two Simple machines have one or two parts. Simple machines are called tools. 2. Write the names of these simple machines. 3. Match. pulley wheel and axle lever wedge screw inclined plane screw lever pulley inclined plane wedge wheel and axle .
answer questions 2.1 - 2.13 Note: You are studying only simple machines in this course. The other category of machines is compound machines, which are made up of two or more simple machines working together. Cars and dishwashers are examples of compound machines. Note: Ask your instructor for a copy of the worksheet, Classes of Levers, to .
distance needed to do work. Simple machines do not change the amount of work done 2) Identify examples of simple machines in everyday objects. 3) Identify simple machines within complex machines. 4) Choose appropriate simple machines to solve a mechanical problem. 5) a) Define engineering design as the process of creating
