Cisco WAP150 Quick Start Guide
Quick Start GuideCisco WAP150 Wireless-AC/N Dual RadioAccess Point with PoE
WelcomeThank you for choosing the Cisco WAP150 Wireless-AC/N Dual RadioAccess Point with PoE. The Cisco WAP150 is an indoor concurrent dualband radio 802.11ac and 802.11n access point with Power over Ethernet(PoE). -PoE Supplied by UL Listed I.T.E.This guide provides the general layout of the Cisco WAP150, describe howto deploy the Cisco WAP150 in your network, and describe how toconfigure the Cisco WAP150. For additional information, seewww.cisco.com/go/100 wap resources.Package Contents Wireless Access Point Power Adapter This Quick Start Guide Ethernet Cable Technical Support Contact Pointer Card China RoHS EU Directives 1999/5/EC Compliance Information (for EU SKU only)1Before You BeginBefore you begin the installation, make sure that you have the followingequipment and services: A computer with browser support for:–Internet Explorer 7.0 or later–Chrome 5.0 or later–Firefox 3.0 or later–Safari 3.0 or later Tools for installing the hardware FindIt tool for locating the access point One or more Ethernet network switches with PoE Mobile devices (iPhone, Android, etc.) via wireless setup SSID.(Configure via Wi-Fi mobile device with a web browser.)2Cisco WAP150 Quick Start Guide
2Cisco WAP150 FeaturesFront PanelThe front panel of the Cisco WAP150 consists of one system LED. For fulldescriptions of the colors of the lights and their indications, see Verifyingthe Hardware Installation.Back PanelRESET—See Rebooting the Cisco WAP150 or Resetting to FactoryDefaults for information on the RESET button.LAN (PoE)—The RJ-45 Ethernet port is used to power the Cisco WAP150using PoE. It is an auto-sensing, Gigabit Ethernet (802.3) port used toconnect the Cisco WAP150 to network devices, such as computers,routers, or switches. We strongly recommend that you use a Category5e or better cable for Gigabit connectivity.POWER—The POWER button is used to turn the power on and off. It is notapplicable when using PoE.12V DC—The 12V DC jack is used to connect the supplied power adapterto the Cisco WAP150 if you are not using PoE.Kensington Lock Slot—The Kensington lock slot is used to attach a cableand lock to the Cisco WAP150.Default SettingsParameterDefault ValueUsernameciscoPasswordciscoLAN IP AddressDHCP address assigned by serverFallback LAN IP192.168.1.245Subnetwork Mask255.255.255.0If you are using a Cisco RV Series router, the default range for the DHCPassigned address is from 192.168.1.100 to 192.168.1.254. Any deviceconnecting to the same LAN will be assigned an IP address in this range.3Mounting the Cisco WAP150There are two ways to physically install the Cisco WAP150:Cisco WAP150 Quick Start Guide3
Place the Cisco WAP150 horizontally on a flat surface so that it sits onits four rubber feet. Mount the Cisco WAP150 to a wall.Wall MountingThe Cisco WAP150 can be wall-mounted using the wall-mount slots on thebottom cover. The wall-mounting hardware is user-supplied.The dimensions for the wall-mount slots and mount kit screws are asfollows:4Cisco WAP150 Quick Start Guide
WARNING Insecure mounting might damage the device or cause injury.Cisco is not responsible for damages incurred by insecure wallmounting.Placement Tips Ambient Temperature—To prevent the Cisco WAP150 fromoverheating, do not operate it in an area that exceeds an ambienttemperature of 104 F (40 C). Air Flow—Be sure there is adequate air flow around the device. Mechanical Loading—The Cisco WAP150 should be level, stable, andsecure to prevent it from sliding or shifting out of position.4Connecting the Cisco WAP150You can perform the initial configuration using either a wired or wirelessconnection. The default configuration of the Cisco WAP150 has the Wi-Firadio turned on.To connect the Cisco WAP150 to the wired network:STEP 1 Connect the Ethernet cable to the Ethernet port of a switch, a router,or a PC.STEP 2 Connect the other end of the network Ethernet cable to theEthernet port of the Cisco WAP150.STEP 3 If PoE is not provided, plug in the supplied power adapter toprovide power to the Cisco WAP150.This wireless default configuration will not allow traffic between WiFi andEthernet; users will need to go through the setup wizard to resume thetraffic between WiFi and Ethernet.To connect the Cisco WAP150 to the network wirelessly:STEP 1 Use wireless clients to locate the WAP150’s SSID (CiscoSB-Setup).STEP 2 Use the ‘cisco123’ passkey to access the access point.NOTE The system provides a one-time-only access to configure theaccess point using a wireless connection.Cisco WAP150 Quick Start Guide5
After installation, all lights should be active. Refer to Verifying theHardware Installation for details about the different lights on the CiscoWAP150.5Verifying the Hardware InstallationTo verify the hardware installation, complete the following tasks: Check the cable connections. Check the state of the indicator light.LabelPowerActivityOffSolid GreenSolid BlueSolid RedLANFlashing GreenFlashing BlueOffSolid GreenSolid AmberFlashingDescriptionThe WAP150 is out of power.The Cisco WAP150 is normal; no wirelessclient connected.The Cisco WAP150 is normal; at least onewireless client connected.The Cisco WAP150 fails to boot with bothfirmware images.The Cisco WAP150 is booting.Firmware upgrade is in progress.No Ethernet link.Gigabit Ethernet link is active.Fast Ethernet link is active.Transmitting or receiving data.NOTE If you need help resolving a problem, visit the Cisco SupportCommunity at www.cisco.com/go/smallbizsupport.6Getting Started with the ConfigurationTo configure the Cisco WAP150, follow these steps to access theweb-based Configuration Utility and then the Setup Wizard from yourcomputer:STEP 1 Connect the Cisco WAP150 to the same network (IP subnet) as yourcomputer. The factory default IP address configuration of the Cisco6Cisco WAP150 Quick Start Guide
WAP150 is DHCP. Make sure that your DHCP server is running andcan be reached.See Incorrect IP Address for troubleshooting information, or if youdo not have a DHCP server.STEP 2 Locate the IP address of the Cisco WAP150.a.The Cisco WAP150 can be accessed and managed by Cisconetwork tools and services including the Cisco FindIT NetworkDiscovery Utility that enables you to automatically discover allsupported Cisco devices in the same local network segmentas your computer. You can get a snapshot view of each deviceor launch the product configuration utility to view and configurethe settings. For more information, see www.cisco.com/go/findit.b. The Cisco WAP150 is Bonjour-enabled and automaticallybroadcasts its services and listens for services beingadvertised by other Bonjour-enabled devices. If you have aBonjour-enabled browser, such as Microsoft Internet Explorerwith a Bonjour plug-in, or the Apple Mac Safari browser, youcan find the Cisco WAP150 on your local network withoutknowing its IP address.You can download the complete Bonjour for Microsoft InternetExplorer browser from Apple’s website by visiting:http://www.apple.com/bonjour/c.Locate the IP address assigned by your DHCP server byaccessing your router or DHCP server. See your DHCP serverinstructions for more information.STEP 3 Launch a web browser, such as Microsoft Internet Explorer.STEP 4 In the address bar, enter the default DHCP address and press theEnter key.STEP 5 Enter the default user name of cisco and password of cisco in theUsername and Password fields.STEP 6 Click Log In. The Wireless Access Point Setup Wizard appears.STEP 7 Follow the Setup Wizard instructions to finish the WAP deviceinstallation.Cisco WAP150 Quick Start Guide7
We strongly recommend that you use the Setup Wizard for the firstinstallation. For more advanced configurations, see theAdministration Guide. A link to the Administration Guide is found inWhere to Go From Here.Congratulations, you can now start using your Cisco WAP150.Suggested Next Steps7In case of an error while installing, try the troubleshooting proceduresdescribed in this section.TroubleshootingIf you cannot display the configuration utility, you can test the ability of thecomputer to communicate with the Cisco WAP150 by using ping. To useping on a computer running Windows:STEP 1 Verify that the Cisco WAP150 is powered on and the lights indicatethe appropriate links.STEP 2 Locate the Cisco WAP150’s IP address. While there are differentways to locate the IP address, this procedure uses Cisco FindIT.a.If you have previously downloaded Cisco FindIT, open InternetExplorer and launch Cisco FindIT. For more information ondownloading Cisco FindIT, see www.cisco.com/go/findit.b. In the Cisco FindIT display, place your mouse over the CiscoWAP150’s name. The Cisco WAP150’s IP address is displayedalong with other device information.STEP 3 Open a command window by choosing Start Run and entercmd.STEP 4 At the command window prompt, enter ping and the CiscoWAP150’s IP address. In this example, we pinged 192.0.2.10.If successful, you should get a reply similar to the following:Pinging 192.0.2.10 with 32 bytes of data:Reply from 192.0.2.10: bytes 32 time 1ms TTL 128If it fails, you should get a reply similar to the following:Pinging 192.0.2.10 with 32 bytes of data:8Cisco WAP150 Quick Start Guide
Request timed out.Possible Cause of Installation FailureNo PowerPower up the switch and your computer if they are turned off.Make sure that your PoE switch is powered on and the lights indicate thatyou have a link. See Verifying the Hardware Installation.Verify that the devices on your network are not plugged into a switchableoutlet.Bad Ethernet ConnectionCheck the state of the indicator lights. See Verifying the HardwareInstallation.Check the Ethernet cable to ensure that it is firmly connected to yourdevices. Devices connected by the Ethernet cable can include the WAPdevices, and routers, any switches, and your computer.Verify that the connected switch has auto-negotiation enabled. The CiscoWAP150 and the switch need the same negotiation parameters set.Bad ImageAfter a new firmware installation, if the POWER light is solid red, whichindicates that the device fails to boot with both firmware images, contactsystem support; see Where to Go From Here.Incorrect IP AddressThe most likely cause of connectivity failure is an incorrect IP address. TheWeb browser may be pointing to the wrong IP address, or your computermay be configured with an IP address that is not in the same subnet as theCisco WAP150.Because the factory default IP address configuration is DHCP, make surethat your DHCP server is running and can be reached. You may need todisconnect and reconnect the devices for them to discover their new IPaddresses from the DHCP server. You can then query the DHCP server forthe new IP address. See Step 2 of Getting Started with theConfiguration for more information on how to find the DHCP address.If the Cisco WAP150 does not receive a DHCP response (there is no DHCPserver on your network) after 60 seconds, the Cisco WAP150 will fallbackto the following default static IP address: 192.168.1.245 and a default maskof 255.255.255.0. To reach that IP address, be sure that your computer ison the 192.168.1.xxx network.Cisco WAP150 Quick Start Guide9
8Rebooting the Cisco WAP150 or Resettingto Factory DefaultsTo reboot your Cisco WAP150: If the Cisco WAP150 uses a power adapter, with the power on, use thePOWER button to reboot the device. The POWER button only functionswhen the Cisco WAP150 uses a power adapter. If the power supply is PoE, unplug your Ethernet connection for threeseconds and plug it back in. With the power on, press the RESET button with an opened paper clipfor less than 10 seconds, or until the lights go off.–When all the lights go off, release the RESET button.–Release the RESET button as soon as the lights go off, or you willrestore the Cisco WAP150 to factory default settings and lose yourconfigurations.To reset the Cisco WAP150 to factory default settings: With the power on, press and hold the RESET button with an openedpaper clip for more than 10 seconds.10–All of the lights will go off.–Release the RESET button when the power light turns on.Cisco WAP150 Quick Start Guide
9Where to Go From HereSupportCisco sco Support andResourceswww.cisco.com/go/smallbizhelpPhone Support Contactswww.cisco.com/en/US/support/tsd cisco small businesssupport center contacts.htmlCisco Cisco Open SourceRequestswww.cisco.com/go/smallbiz opensource requestCisco Partner Central(Partner Login Required)www.cisco.com/web/partners/sell/smbSelect a link to download firmware for Ciscoproducts. No login is required.Product DocumentationCisco WAP150Administration Guidewww.cisco.com/go/100 wap resourcesCisco Power Adapterswww.cisco.com/go/wap accessoriesFor EU lot 26 related test result, please check this web page:www.cisco.com/go/eu-lot26-results.Cisco WAP150 Quick Start Guide11
Americas HeadquartersCisco Systems, Inc.www.cisco.comCisco has more than 200 offices worldwide.Addresses, phone numbers, and fax numbersare listed on the Cisco website atwww.cisco.com/go/offices.78-100810-01Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliatesin the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of theirrespective owners. The use of the word partner does not imply a partnership relationshipbetween Cisco and any other company. (1110R) 2015 Cisco Systems, Inc. All rights reserved.
Mobile devices (iPhone, Android, etc.) via wireless setup SSID. (Configure via Wi-Fi mobile device with a web browser.) 1. Cisco WAP150 Quick Start Guide 3 Cisco WAP150 Features . ping on a computer running Windows: STEP 1 Verify that the Ci
Cisco ASA 5505 Cisco ASA 5505SP Cisco ASA 5510 Cisco ASA 5510SP Cisco ASA 5520 Cisco ASA 5520 VPN Cisco ASA 5540 Cisco ASA 5540 VPN Premium Cisco ASA 5540 VPN Cisco ASA 5550 Cisco ASA 5580-20 Cisco ASA 5580-40 Cisco ASA 5585-X Cisco ASA w/ AIP-SSM Cisco ASA w/ CSC-SSM Cisco C7600 Ser
WorkGroup Bridge 111 Quality of Service 114 Chapter 6: System Security 117 RADIUS Server 117 802.1X/802.1X Supplicant 119 Configure 802.1X Supplicant for Cisco WAP150 119 Configure 802.1X for Cisco WAP361 121 Password Complexity 124 WPA-PSK Complexity 125 Chapter 7: Quality of Service 127 Global Settings 127 Configuring QoS Settings for Cisco .
Sep 11, 2017 · Note: Refer to the Getting Started with Cisco Commerce User Guide for detailed information on how to use common utilities for a record in Cisco Commerce. See Cisco Commerce Estimates and Configurations User Guide for more information.File Size: 664KBPage Count: 5Explore furtherSolved: Cisco Serial Number Lookups - Cisco Communitycommunity.cisco.comHow to view and/or update your CCO profilewww.cisco.comSolved: How do I associate a contract to my Cisco.com .community.cisco.comHow do I find my Cisco Contract Number? - Ciscowww.cisco.comPower calculator tool - Cisco Communitycommunity.cisco.comRecommended to you b
Apr 05, 2017 · Cisco 4G LTE and Cisco 4G LTE-Advanced Network Interface Module Installation Guide Table 1 Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Description Mode Operating Region Band NIM-4G-LTE-LA Cisco 4G LTE NIM module (LTE 2.5) for LATAM/APAC carriers. This SKU is File Size: 2MBPage Count: 18Explore furtherCisco 4G LTE Software Configuration Guide - GfK Etilizecontent.etilize.comSolved: 4G LTE Configuration - Cisco Communitycommunity.cisco.comCisco 4G LTE Software Configuration Guide - Ciscowww.cisco.comCisco 4G LTE-Advanced Configurationwww.cisco.com4G LTE Configuration - Cisco Communitycommunity.cisco.comRecommended to you b
Supported Devices - Cisco SiSi NetFlow supported Cisco devices Cisco Catalyst 3560 Cisco 800 Cisco 7200 Cisco Catalyst 3750 Cisco 1800 Cisco 7600 Cisco Catalyst 4500 Cisco 1900 Cisco 12000 Cisco Catalyst 6500 Cisco 2800 Cisco ASR se
Cisco Nexus 1000V Cisco Nexus 1010 Cisco Nexus 4000 Cisco MDS 9100 Series Cisco Nexus 5000 Cisco Nexus 2000 Cisco Nexus 6000 Cisco MDS 9250i Multiservice Switch Cisco MDS 9700 Series Cisco Nexus 7000/7700 Cisco Nexus 3500 and 3000 CISCO NX-OS: From Hypervisor to Core CISCO DCNM: Single
Cisco Nexus 7706 Cisco ASR1001 . Cisco ISR 4431 Cisco Firepower 1010 Cisco Firepower 1140 Cisco Firepower 2110 Cisco Firepower 2130 Cisco FMC 1600 Cisco MDS 91485 Cisco Catalyst 3750X Cisco Catalyst 3850 Cisco Catalyst 4507 Cisco 5500 Wireless Controllers Cisco Aironet Access Points .
AWJM, the abrasive particles are allowed to entrain in water jet to form abrasive water jet with significant velocity of 800 m/s. Such high velocity abrasive jet can machine almost any material. Fig. 1 shows the photographic view of a commercial CNC water jet machining system along with close-up view of the cutting head.
