Chevy Silverado 1999-2005, Chevy Suburban 2000-2005, Chevy .

3y ago
83 Views
2 Downloads
1.36 MB
16 Pages
Last View : 15d ago
Last Download : 2m ago
Upload by : Camden Erdman
Transcription

Signal Mirror Installation InstructionsChevy Silverado 1999-2005, Chevy Suburban 2000-2005, Chevy Tahoe 2000-2005, Cadillac Escalade2002-2005, Cadillac Escalade EXT 2002-2005, GMC Sierra 1999-2005, GMC Yukon XL 2000-2005,GMC Yukon Denali 2001-2005, Chevy Avalanche 2002-2005For 2003 plus model year, please go to page 5THE safety accessory of the 21st Century. P/N 210-0015-0Rev. K4 (9-15-04), GG 2003 Muth Mirror Systems, LLC.

Note: Professional Installation RecommendedWarranty does not cover damage to the vehicle or mirror housing due to improper installation. Thefollowing installation instructions are to be considered as a guide only. Door removal procedures,indicator wire color and location may have changed since publication of these instructions. The installeris responsible for any damage that may occur during installation.INCLUDED ITEMS:1 left and 1 right Signal mirror1 left and 1 right wire harness2 wire taps2 ring connectors1 instruction manualPlease read instructions prior to installation.PROBLEMS OR QUESTIONS?REQUIRED TOOLS:Ratchet with extension or ratcheting screwdriver10mm socket7mm socket8mm socketSmall slotted screwdriverMedium Philips screwdriverNeedle nose pliersSmall pry bar, Heater GunGopher wireElectrical tapeWire crimper and stripperMultimeterSturdy glovesSafety glasses or gogglesTechnical Assistance is available by callingMuth Mirror Systems Technicians at:1-800-844-6616Monday through FridayBetween 8:00 a.m. and 5:00 p.m. CSTOr through the Muth web site: www.muthco.comOr via E-mail: techsupport@muthco.com

Mirror Housing Removal23761451. Open driver side door. Lower window.2. Remove door lock cover.3. Unsnap and remove the triangular molding that covers themirror mounting screws.4. Unsnap and remove the molding that covers the door handle.Remove the screw behind the door handle.5. Unsnap the control console and unplug the wires. Remove thescrew located behind the arm rest.6. Dislodge the door panel by pulling it up and away from the doorslightly. Disconnect light and tweeter connections and removedoor panel.7. Secure mirror with one hand. Proceed cautiously to avoiddropping articles into the door panel. Remove the 3 mirrormounting nuts using a 10mm socket.8. Remove mirror from door.

Mirror Replacement9Caution: Safety glasses and sturdy gloves are recommendedfor the following steps.9. Place the mirror housing on a clean level surface. Push on theouter edge of the mirror to manually pivot it fully outward so aflat head screwdriver can be inserted under its inner edgebetween the backplate and motor actuator. Gently twist andpull on the screwdriver until backplate dislodges from motoractuator. Repeat the process by moving the screwdriveraround until backplate unsnaps from motor actuator. NOTE: Ifyou have heated mirrors, disconnect the heater wires fromthe heater terminals. The polarity on the heater terminals isreversible so it is not necessary to label the terminals.Remove OE mirror from mirror housing.1010. Remove the rubber insulation on the mirror mountingframe to expose the wire routing passage. Locate the correctSignal mirror harness (short for driver side and long forpassenger side). Slide the end with no connector through therouting passage (from the inside of the mirror housing) andthrough the hole in the rubber insulation. Attach the rubberinsulation to the mirror mounting frame. Pull the harnessthrough leaving about 6 inches of slack in the harness near themotor pack.-2-

Mirror Replacement Continues11121311. For both driver and passenger side mirrors, remove therubber boot around the motor actuator PRIOR to installing the Signal mirror into the mirror housing. NOTE: Permanent removal of rubberboot, by pulling it over the motor, is required for this applicationand will not negatively affect operation or durability, per the mirrormotor manufacturer.12. Connect the Signal mirror to the wiring harness plug. Ifheated, reconnect the heater wires to the heater terminals on theSignal mirror.13. Align the motor mount with the motor actuator. Place the palm ofyour hand on the center of the glass and press firmly until youhear the snaps engage onto the motor puck. Press on the top,bottom and both sides of the mirror to ensure completeattachment to the motor puck. (Mirror should be pivoted throughits full range of travel during this step.)

Mirror Housing Attachment16IIIIIIA14. Feed wires into door and set mirror in place.15. Attach mirror with the (3) original nuts. Do not over tighten.16. Pass Signal mirror harness thru door frame as shown. CAUTION: Whenrouting harness through door frame, be sure to avoid the latch hole (A) andgoing inside window track. Caution not heeded, could cause damage to wiringharness.17. Remove sill plate and kick panel. Continue routing Signal mirror harness thrurubber boot and into vehicle. Make sure to reconnect all wiring connectionson door panel and control consol. Insert key in the ignition and test allbuttons on the control consol to make sure everything is in working order.Replace door panel.***Repeat all steps for passenger side Signal mirror***1718. Wiring locations are located just to the left and below the steering column. Youmay need to remove the dash board and the knee panel for better access towiring locations. The following steps will guide you in the removal of the dashboard and knee panel. (I) – Unsnap all around dash panel. (II) – Insert key inthe ignition and turn it to the “ON” position. While stepping on the brake pedal,shift the steering wheel and the shift lever all the way down to their lowestposition. Lift up and pull out the dash panel. Move the shift lever and thesteering wheel back to their “original” position. (III) – Remove the (2) screwsholding the knee plate in place using the 7 mm socket. Remove the knee platefrom under the steering column.-3-

Wiring1. Find the bundle of wires just to the left and below the steering column. You may need to remove a plastic wire sheath. Locate theLight Blue wire. Turn the ignition key so that electrical power is on and activate the driver side turn indicator. Probe the LightBlue wire to verify that flashing turn indicator power is present. Deactivate the turn indicator and depress the brake to make sureyou have not located the rear turn wire. Label that wire as front, DRIVER SIDE TURN.2. Locate the Dark Blue wire and activate the passenger side turn indicator. Probe the Dark Blue wire to verify that flashing turnindicator power is present. Deactivate the turn indicator and depress the brake to make sure you have not located the rear turnwire. Label that wire as front, PASSENGER SIDE TURN.3. Make sure the harnesses are routed securely under the dash and enough slack is left for splicing. Strip and twist together theends of the black wires from each harness. Crimp them together in the supplied ring connector and ground to a suitable nearbylocation on the metal framework of the vehicle.*** SKIP TO THE LAST PAGE ***

This page is intentionally left blank-4-

Door Panel Removal – 2003 plus model year1231. Remove lock cover by prying with small screwdriverfrom the outside of cover.2. Using 7mm socket, remove the (3) bolts – firstone behind lock cover, second one under doorhandle, and last one on the bottom of doorpanel.3. Pry off cover that goes around door lever.

Mirror Housing Removal1231. Remove small triangular cover from top of doorpanel.2. Lift door panel up and away from door. Disconnect all wiring connections.3. Using 10mm socket, remove (3) bolts holding themirror housing to the door. Remove mirror housingfrom door.- 5-

Mirror Replacement12Caution: Safety glasses and sturdy gloves are highly recommended for the following steps.1. Place the mirror housing on a clean level surface. Push on the outer edge of the mirror to manually pivot it fullyoutward so a small pry bar can be inserted under its inner edge. Apply gentle pressure with the pry bar until themirror backing plate begins to unsnap from the motor. Move the pry bar around the mirror and pry again untilthe mirror backing plate further unsnaps from the motor. Pull the mirror off of the motor. Some force may berequired to free any remaining snaps but it should not be excessive. If you can not remove the mirror withoutexcessive force, apply the pry bar further around its edge to loosen more snaps. Then try again.2. If you have heated mirrors, disconnect the wires when you remove the mirror. The polarity forthe heaters is reversible so it is not necessary to label the wires.

Mirror Replacement Continues3453. Pull back the rubber insulation on the mirror mounting frame to expose the wire routing passage. Locate thecorrect Signal mirror harness (short for driver side and long for passenger side) and slide the end with noconnector through the routing passage (from the inside of the mirror housing) and through the hole in the rubberinsulation. Leave about 6 inches of slack in the harness near the motor pack.4. For both driver and passenger side mirrors, remove the rubber boot around the motor actuator PRIOR to installingthe Signal mirror into the mirror housing. NOTE: Permanent removal of rubber boot, by pulling it over themotor, is required for this application and will not negatively affect operation or durability, per the mirrormotor manufacturer.5. Connect the Signal mirror leads to the harness. (If you have heated mirrors, connect the wires to the heaterterminals at this time.) Place the Signal mirror over the motor puck. Place the palm of your hand on the centerof the glass and press firmly until you hear the snaps engage onto the motor puck. Press on the top, bottom andboth sides of the mirror to ensure complete attachment to the motor puck. (Mirror should be pivoted through its fullrange of travel during this step.)-6-

Mirror Housing Attachment121. Route Signal mirror wire harness through hole along OE wire harness.2. Using 10mm socket, reconnect the (3) bolts holding the mirrorhousing to the door.***Wiring location is located within each of the door panel area***3. DRIVER SIDE: Probe the Light Blue wire to verify that flashing turn indicatorpower is present. Deactivate the turn indicator and depress the brake to makesure you have not located the rear turn wire. Label that wire as front, DRIVERSIDE TURN. PASSENGER SIDE: Probe the Dark Blue wire to verify thatflashing turn indicator power is present. Deactivate the turn indicator anddepress the brake to make sure you have not located the rear turn wire. Labelthat wire as front, PASSENGER SIDE TURN.NOTE: Triple check to ensure you have the correct indicator wire, as thereare several of them to choose from.3

Wiring121. Make sure the harnesses are routed securely and enough slack is left for splicing. Split and cut the Signal mirror harness to length.2. Strip the black wire and crimp on yellow grounding ring. Using a 10mm socket wrench, remove the bolt by the speaker. Attach thegrounding ring to the bolt and tighten the bolt in place.- 7-

Wiring Continues1234USE THE INCLUDED WIRE TAPS AND FOLLOW THE FOUR STEPS ABOVE TO SPLICE INTO THE TURN INDICATOR WIRES1.2.3.4.Splice the RED wire from the driver side harness into the Light Blue wire previously labeled ‘driver side turn’.Splice the RED wire from the passenger side harness into the Dark Blue wire previously labeled ‘passenger side turn’.Activate each turn indicator to verify that the Signal mirrors are working.Replace any door accessories, door panels, plastic moldings, and trim pieces.

This page is intentionally left blank- 8-

Chevy Silverado 1999-2005, Chevy Suburban 2000-2005, Chevy Tahoe 2000-2005, Cadillac Escalade 2002-2005, Cadillac Escalade EXT 2002-2005, GMC Sierra 1999-2005, GMC Yukon XL 2000-2005, GMC Yukon Denali 2001-2005, Chevy Avalanche 2002-2005 THE safety accessory of the 21st Century.

Related Documents:

pickup pickup pickup pickup pickup s10 s10 s10 s10 s10 s10 s10 s10 s10 s10 s10 s10 silverado silverado silverado silverado silverado silverado silverado silverado silverado silverado venture . 85 ford . 86 ford . 87 ford . 88 ford . 89 ford . 90 ford . 91 ford . 92 ford . 93 ford . 94 ford . 95 gmc 96 gmc 97 gmc 98 gmc 99 gmc 100 gmc

Jada Toys Dub City - Chevy Silverado (2002, 1:18, Candy Purple) 63112MB5 Item# 63112MB5 Jada Toys Dub City - Chevy Silverado (2002, 1:18, Red) 63112MR5 Item# 63112MR5 Jada Toys Dub City - Chevy Silverado (2002, 1:24, Asstd.) 53809 Item# 53809 Jada Toys Dub City - Chevy Silverado

SILVERADO I STRONG bACkup fOR yOu. Silverado 1500 Crew Cab LTZ 4x4 shown in Silver Ice Metallic with available features and dealer-installed Chevy Accessories. Substantial and strong, Silverado is there from sunup to sundown. Whether taking on mud-rutted back roads or steep mountain grades, towing a boat or hauling stacks of drywall, this is one

SILVERADO IS STRONG bACkup fOR yOu. Silverado 1500 Crew Cab LTZ 4x4 shown in Silver Ice Metallic with available features and dealer-installed Chevy Accessories. Substantial and strong, Silverado is there from sunup to sundown. Whether taking on mud-rutted back roads or steep mountain grades, towing a boat or hauling stacks of drywall, this is one

Chevy Chase Library 3301 East Chevy Chase Drive CCEA'S 80th ANNUAL MEETING The 80th Annual Meeting of the Chevy Chase Estates Association will be held on Wednesday, March 8, 2017, at the Chevy Chase Library, 3301 East Chevy Chase Drive. The evening will start with a half-hour social at 7:00 p.m. At 7:30 p.m., we will conduct the business .

brand. So owning a Chevy isn't just a source of transportation. It's a source of pride. CHEVY.COM 1 Based on EPA estimates for 2010 Aveo Sedan, Aveo5, Cobalt, Cobalt XFE, Equinox FWD, HHR, HHR Panel and Malibu. 2 Whichever comes first. See dealer for details. 3 Models include Malibu, Traverse, Silverado 1500 and others.

Silverado/Sierra 1500 Ext Cab 6.0L V-8 10,000 (a,u,z)/ 4WD Standard Bed 7,900 (a,s)/ 9,900 (a,u) Silverado/Sierra 1500 Ext Cab 4.8L V-8 6,500 (a,q or s,z)/ 4WD Longbed 6,900 (a,q or s) Silverado/Sierra 1500 Ext Cab 4.8L V-8 7,500 (a,u,z)/ 4WD Longbed 7,900 (a,u) Silverado/Sierra 1500 Ext Cab 5.3L V-8 7,500 (a,q or s,z)/ 4WD Longbed 7,900 (a,q or s)

Designed by Cardiff Archaeological Illustration and Design Software: Adobe Creative Suite 6 Design Premium EXCAVATIONS AT CAERAU HILLFORT, CARDIFF, SOUTH WALES, 2014 National Primary Reference Number (NPRN) 94517 Cadw Scheduled Ancient Monument No. GM018. Contents 1. Introduction 1 2. Background 3 3. Previous Archaeological Work 7 4. Project Aims & Objectives 9 5. Excavation Methodology 13 6 .