HONDA4 - Microsoft
INSTALLATION GUIDEHONDA4Designed by Installers for Installers 2016 Directed, Vista CAThis product is intended for installation by a professional installer only! Attempts to install thisproduct by a person other than a trained professional may result in severe damage to a vehicle’selectrical system and components.2016-12-19Directed DigitalSolutions
ContentsWarning! Safety first. 3Introduction. 4Pre-installation and application warnings. 4Vehicle application guide. 5Wiring connections. 6Main power harness (H1), 12-pin thick gauge connector. 6Auxiliary output harness (H2), 16-pin black connector. 6Analog harness (H3), 18-pin white connector. 7MC501 harness (H4), 8 thick-gauge wires (optional). 7Installation (wiring diagrams & vehicle wiring reference charts). 8Type 1 with T-Harness (THHOC5). 8Type 1. 9Type 2 with T-Harness (THHOC6). 12Type 2. 13Type 3 with T-Harness (THHOC5). 17Type 3. 18Type 4 with T-Harness (THHOC5). 22Type 4. 23Type 5 with T-Harness (THHOC5). 25Type 5. 26Type 6 with T-Harness (THHOC5). 29Type 6. 30Key2GO. 32Connecting the module. 32Important!. 32Manual or automatic transmission selection. 32Optional sensors. 33RF Systems. 33When used in conjunction with SmartStart. 33Module programming. 34LED diagnostics and troubleshooting. 35Soft reset. 37Hard reset. 37Learning the Tach (not needed with Virtual Tach). 38Initializing Virtual Tach (not needed with hardwired or data tach applications). 38Limited lifetime consumer warranty. 39Quick Reference Guide. 40
Warning! Safety first The The following safety warnings must be observed at all times:Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, neveroperate the system in an area that does not have adequate ventilation.following precautions are the sole responsibility of the user; however, authorized Directed dealers should:Never use a test light or logic probe when installing this unit. Always use a multimeter.Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system mustbe disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach fromchildren all remote controls to assure that the system does not unintentionally remote start the vehicle.USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLESTORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, ordeath. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle withthe vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having theneutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this productinstallation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problemimmediately.OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OFOPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGEOR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTESTART MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure theinstallation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engagedparking brake. Do not allow anyone to stand in front of or behind the vehicle.This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in suchvehicles may pose certain risk.3Directed Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
IntroductionThe HONDA4 firmware for Directed Digital Solutions is a complete solution for remote start, security (ifapplicable), bypass interface, and convenience needs compatible with specific ACURA and HONDA vehicles.Warning! This module can only be programmed via the web tool, which can be found onwww.directechs.com or using the Directechs Mobile application for smartphones. Features and functions willbecome accessible when you connect the module using the XKLoader.Pre-installation and application warningsFirmware notes: This section highlights important information for this specific firmware and will assist inpricing accordingly, as well as bringing awareness to any operational or vehicle limitations.T-HarnesscompatibleKeys required forprogrammingTHHOC5 & THHOC61Keys required foroperation0 The optional Plug & Play THHOC5 & THHOC6 T-Harnesses are sold separately. The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed. Key2GO may be required if the interface does not program using the traditional method. Refer to "Module programming"on page 34 for more information. All connectors are displayed from the wire side (unless specified otherwise). Refer to the "Vehicle wiring reference chart" following each installation type.General notes: This section highlights important information for this specific firmware.[1][2][3][4]The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.The siren is only compatible with hybrid systems.Connect this wire only if the Trunk Release feature is not supported in data. See the Vehicle application guide for moreinformation on supported features.The Green wire is only required for starter disable and antigrind connections.Additional parts required (maximum required):876A0 xDiode1A Diodes8687a8530Resistor 100Ω0 x ResistorFuse 7.5A0 x Fuse0 x Relay4Directed Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
Vehicle application guideSS-Entry Monitoring Trunk/Hatch PinST-Brake Status (foot brake)ST-E-Brake Status DL-Sliding Door Control Passenger DL-Sliding Door Control DriverSS-Entry Monitoring Hood Pin5 53 3 3 3 31 1 1 1 11 1 1 1 116 15 14 13 12 11 10 09 08 07 06 05 04 03 02 011 1 1 1 11 1 12 2 2 2 2 23 3 3 3 32 2 2 2 23 3 32 2 2 2 23 3 3 3 32 2 2 2 2 23 3 3 3 3 3 3 3 32 2 2 2 2 24 421 1 1 1 1 16 6 6 61 1 1 1 1 1 1 1 1SS-Entry Monitoring Driver Door Pin25SS-Entry Monitoring ALL Door Pins25RS-Tach / RPM Output254RS-3x LOCK START (Start control using OEM Remote)254FOB-Control of aftermarket alarm with OEM remote25424253DL-Driver Priority Unlock23DL-Door Unlock23DL-Door Lock Control23DL-Disarm Factory Security23DL-Arm Factory Security2PK-Immobilizer Bypass-Data No Key daAccordAccord HybridCivicCivicCivic HybridCivic Ridgeline20152016VehiclesDL-Trunk / Hatch ReleaseThe following table lists the vehicles and features which are compatible with this product. The number assigned to each yearallows you to determine which installation type should be used for your vehicle. Legend:AV: Horn & Light ControlsCC: Comfort & Convenience ControlsDL: OE Door Lock & Alarm ControlsFOB: Sync CAN Interface w/ FOB RemotePK: Transponder & Immobilizer OverrideRS: Remote Start & Engine ControlsSS: Integrated Security & MonitoringST: Function/Feature Status5Directed Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
Wiring connectionsThe wiring connections listed below are specific to this firmware.Main power harness (H1), 12-pin thick gauge connectorConn./PinColorDescriptionH1/1WhiteRelay 3 COM – ( ) Parking Light Output 1H1/2White/BrownRelay 3 N.O. – ( ) Parking Light Input 1H1/3Brown/RedRelay 2 N.O. – No ConnectionH1/4Yellow/RedRelay 2 COM – OEM Security Light Interrupt (vehicle side)H1/5Orange/RedRelay 2 N.C. – OEM Security Light Interrupt (connector side)H1/6YellowRelay 1 COM – OEM Security Ignition Interrupt (vehicle side) Input 1H1/7WhiteRelay 3 COM – ( ) Parking Light Output 1H1/8White/BrownRelay 3 N.O. – ( ) Parking Light Input 1H1/9Black(-) GroundH1/10Red( ) 12 Volt (Battery)H1/11Orange/YellowRelay 1 N.C. – OEM Security Ignition Interrupt (connector side) InputH1/12BrownRelay 1 N.O. – ( ) Power 12 Volt 1Auxiliary output harness (H2), 16-pin black No ConnectionH2/2Yellow/BlackDoor Lock DataH2/3Orange/BlackImmobilizer DataH2/4TanHS CAN LowH2/5Tan/BlackHS CAN HighH2/6Light GreenSingle Wire CANH2/7Orange/GreenNo ConnectionH2/8Orange/BrownNo ConnectionH2/9Violet/GreenNo ConnectionH2/10Green/Black(-) Lock OutputH2/11White/VioletNo ConnectionH2/12White/RedNo ConnectionH2/13Lt. Blue/Black(-) Unlock OutputH2/14Green/RedNo ConnectionH2/15N/ANo ConnectionH2/16Violet/YellowNo Connection1.2.62If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relaymay be necessary.Directed Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
Analog harness (H3), 18-pin white connectorConn./PinColorDescriptionH3/1Lt. Blue/Red(-) Door Lock Activation InputH3/2Black/White(-) Parking Brake Input (Manual Transmission)H3/3Gray(-) Hood InputH3/4N/ANo ConnectionH3/5Gray/Black( ) Glow Plug InputH3/6Violet/White(AC) Tach InputH3/7Dark Blue(-) Unlock Output 1H3/8Brown/Black(-) HornH3/9Red/White(-) Trunk Release Output 1H3/10White/Green(-) Door InputH3/11Yellow/Green( ) Door Input2222122H3/12Blue/RedNo ConnectionH3/13Light Blue(-) Trunk Trigger InputH3/14Pink/YellowNo Connection 1H3/15Dark Green(-) Lock OutputH3/16Brown/White( ) Brake InputH3/17Brown( ) Siren Output 1H3/18Blue/White(-) Ground When Running (Status) Output221MC501 harness (H4), 8 thick-gauge wires (optional)Conn./PinColorDescriptionH4/1Pink/White( ) Ignition 2/Flex Relay Output 3H4/2Red/White( ) Fused (30A) Ignition 2/Flex Relay InputH4/3Pink( ) Ignition Output (Also Input to Yellow in Ribbon Cable)H4/4Red( ) 12 Volt (Battery) InputH4/5Orange( ) Accessory OutputH4/6Red( ) 12 Volt (Battery) InputH4/7GreenStarter Input (From Key Switch) 4H4/8Violet( ) Starter Output (To Starter)1.2.3.4.7If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relaymay be necessary.These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle wiring reference chart" on page 14for a list of compatible features.If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.The Green wire is only required for starter kill and anti-grind applications.Directed Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
Installation (wiring diagrams & vehicle wiring reference charts)Type 1 with T-Harness (THHOC5)Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 10 for important information on this installation.45 44 43Parking Lights:Red/Black, pin 1942 41 40 3938 3736 353433 32 31 30 29 282227 26 25 24 23212019 18 17 16 1514 1312 11 10 96 5874 3 2 113 4Fuse/Relay Box25 6Ignition Switch(White or Brown conn.and ignition cylinder)(Green conn.under drivers side dash)1234567Immobilizer Connector(Green conn.at ignition cylinder)1234567ORFor 2005-2010Odyssey ONLYParking Lights: Red/Black, pin 1921 20 19 18 17 16 15 14 13 12 11 109 8 7 65 4 3 2 1Single Wire CAN: pin 4Fuse/Relay BoxSingle Wire CAN: Lt. Green16-pin BlackConnectorRemote Start SafetyOverride SwitchTHHOC5(optionalT-Harness)(Green conn.under drivers side dash)The Remote StartSafety OverrideSwitch MUST be inthe ON position.(-) Hood Input: Gray: 3Hood PinRefer to the Vehiclewiring referencecharts for moreinformation on wireand connector details.8(-) Trunk Release/Power LiftgateOutput: Red/White: 912-pinWhiteConnectorWhite: ( ) Parking Light Output( ) Siren Output: Brown: 17SirenDirected Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
Type 1Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 10 for important information on this installation.ORFor 2005-2010Odyssey ONLY45 44 4342 41 40 3938 3736 353433 32 31 30 29 282227 26 25 24 2321Parking Lights:Red/Black, pin 192019 18 17 16 1514 1312 11 10 96 5Fuse/Relay Box(Green conn.under driversside dash)8721 20 19 18 17 16 15 14 13 12 11 109 8 7 65 4 3 2 1Immobilizer Data: Orange/Black: 3Single Wire CAN: pin 4Immobilizer conn.(green connectorat ignition cylinder)1234567Remote Start SafetyOverride Switch( ) Starter Output (car side): Violet: 8( ) Accessory Output: Orange: 5( ) 12V Input: Red: 4MC501The Remote StartSafety OverrideSwitch MUST be inthe ON position.7 White( ) Fused (30A) Ignition 2/Flex Relay Input: Red/White: 24 White( ) 12V Input: Red: 6( ) Ignition Input/Output: Pink: 3( ) Ignition:pin 6Security Light:pin 5Single Wire CAN: Lt. Green: 68 thick-gauge wires( ) 12V: pin 2123 4 5 6CutImmobilizerData: pin 2Starter Input (key side): Green: 7( ) Accessory:pin 4(conn.under drivers side dash)Parking Lights: Red/Black, pin 19Ignition Switch(White or Brown conn.and ignition cylinder)( ) Starter:pin 1Fuse/Relay Box4 3 2 1( ) Ignition 2/Flex RelayOutput: Pink/White: 110: Red: ( ) 12V9: Black: (-) GroundHood Pin(-) Hood Input: Gray: 3Refer to the Vehiclewiring referencecharts for moreinformation on wireand connector details.9(-) Trunk Release/Power LiftgateOutput: Red/White: 9( ) Siren Output: Brown: 17Siren5: Orange/Red: OEM Security Light Interrupt (conn side)4: Yellow/Red: OEM Security Light Interrupt (vehicle side)2 & 8: White/Brown: ( ) Parking Light Input1 & 7: White: ( ) Parking Light OutputDirected Digital Solutions HONDA4 2016-12-19 Directed. All rights reserved.
Vehicle wiring reference chartThis section provides vehicle wiring information to guide you through the various stages of your installation. Refer towww.directechs.com for additional information.Wire InformationFunctionColorConnector InformationPinPolarityLocationColorPinsRef.Acura TL 2004-2006Immobilizer DataRed/Blue2DataImmobilizer connector.Green7ASecurity LightBlue/Orange5DataImmobilizer connector.Green7A12VWhite2( )Ignition switch.Brown7BAccessoryBlack/Red4( )Ignition switch.Brown7BIgnitionBlack/Yellow6( )Ignition switch.Brown7BStarterBlack/White or Black1( )Ignition switch.Brown7BSW CANBrown/Black4DataDrivers fuse/relay box.Green21CParking LightsRed/Black31( )Drivers fuse/relay box.White45DTrunk ReleaseYellow/Green2( )Trunk release switch.Blue5N/AImmobilizer DataYellow2DataImmobilizer connector.Green7ASecurity LightOrange5DataImmobilizer connector.Green7AAcura TL 2007-200812VBrown/Black2( )Ignition switch.Brown7BAccessoryBlack/Red4( )Ignition switch.Brown7BIgnitionBlack/Yellow6( )Ignition switch.Brown7BStarterBlack/White or Black1( )Ignition switch.Brown7BSW CANBrown/BlackParking LightsRed/BlackTrunk Release4DataDrivers fuse/relay box.Green21C31( )Drivers fuse/relay box.White45DYellow/Green2( )Trunk re
2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release FOB-Control of aftermarke
o Microsoft Outlook 2000 o Microsoft Outlook 2002 o Microsoft Outlook 2003 o Microsoft Outlook 2007 o Microsoft Outlook 2010 o Microsoft Outlook 2013 o Microsoft Outlook 98 o Microsoft PowerPoint 2000 o Microsoft PowerPoint 2002 – Normal User o Microsoft PowerPoint 2002 – Power User o Microsoft PowerPoint 2002 – Whole Test
Business Ready Enhancement Plan for Microsoft Dynamics Customer FAQ Updated January 2011 The Business Ready Enhancement Plan for Microsoft Dynamics is a maintenance plan available to customers of Microsoft Dynamics AX, Microsoft C5, Microsoft Dynamics CRM, Microsoft Dynamics GP, Microsoft Dynamics NAV, Microsoft Dynamics SL, Microsoft Dynamics POS, and Microsoft Dynamics RMS, and
Microsoft, Microsoft Dynamics, logo systemu Microsoft Dynamics, Microsoft BizTalk Server, program Microsoft Excel, Microsoft.NET Framework, program Microsoft Outlook, Microsoft SharePoint Foundation 2010, Microsoft SharePoint Ser
Microsoft Dynamics 365 for Operations on-premises, Microsoft Dynamics NAV, Microsoft Dynamics GP, Microsoft Dynamics SL, Microsoft Dynamics AX 2012 or prior versions, or Microsoft Dynamics CRM 2016 or prior versions. This guide is not intended to influence the choice of Microsoft Dynamics products and services or provide technical specification.
References to Microsoft Word, Microsoft Excel, and Microsoft PowerPoint are to the latest version of Microsoft Office as of May 1, 2005. The information on Microsoft Word, Microsoft Excel, and Microsoft PowerPoint contained herein has been derived from the applicat
2007 Microsoft Office System Microsoft Office Project 2007 Microsoft Office Visio 2007 Visual Studio 2005 Microsoft Dynamics CRM 3.0 Product Licensing — Systems . The Microsoft Licensing Reseller Handbook is a one-stop partner resource to help you understand Microsoft licensing options and complete more Microsoft solution sales. .
Upon submission of a request to register a .Microsoft domain name, or by asking Microsoft to renew a .Microsoft domain name registration, Registrant represents and warrants that Registrant's .Microsoft domain name registration does and will at all times comply with the .Microsoft Registration Policy and the .Microsoft Registry T&Cs.
Elliot Aronson Timothy D. Wilson Samuel R. Sommers A01_ARON1287_10_SE_FM.indd 1 12/2/17 12:08 AM. Portfolio Manager: Kelli Strieby Content Producer: Cecilia Turner/Lisa Mafrici Content Developer: Thomas Finn Portfolio Manager Assistant: Louis Fierro Executive Product Marketing Manager: Christopher Brown Senior Field Marketing Manager: Debi Doyle Content Producer Manager: Amber Mackey Content .
