Swimming Pool Heat Pump INSTALLATION AND USER MANUAL
Swimming Pool Heat PumpINSTALLATION AND USER MANUALPHCP50PHCP65PHCP80PHCP1101Rev 3 Dec 16
ContentI. Application . 4II. Features . 4III. Technical Parameters . 5IV. Dimension . 6V. Installation Guide . 7VI. Operation Instruction . 9VII.Testing. 11VIII. Precautions. 12IX. Maintenance . 14X. Troubleshooting . 14XI. Service . 15XII. Warranty . 15XIII. Exploded Views and Parts Listings . 162
WarningA. DO NOT use this unit for any other purpose than to regulate swimming pool watertemperature. Utilization for any other application will void warranty.B. The inlet & outlet connection joint cannot support any other piping system’s weight.C. Make sure outlet air do not hurt any person, animal & plant.D. Please make sure to switch off the power before any examination and repair.PrecautionsA. The unit must be installed & maintained by professional technician, the Powerlayout must comply with local concerned regulation. Please read the manualcarefully.B. Set proper temperature in order to get desired water temperature.C. Please do not stack substances that can block air flow near inlet or outlet area.D. The unit will automatically start up upon power available although power stopduring operation.E. If the machine is stopped for a long time or in winter season, please cut off thepower supply and drain water clear of the machine by opening the tap of inlet pipe.F. Do not put your hand or pole into air outlet of evaporator, forbid to disassemble theworking fan.G. If any abnormal status occurs such as abnormal noise, smell, smoke, electricityleakage, please switch off power immediately and contact your local dealer, pleasedo not check the unit by yourself.H. Do not store combustible or flammable material near unit.3
I. Application1- Set swimming pool water temp efficiently and economically to provide you comfortand pleasure2- User may choose the model technical parameter according to professional guide, thisseries of swimming pool heater has been optimized in factory (refer to technicalparameter table).II. Features1- High efficient titanium heat exchanger2- Sensitive and accurate temp control and water temp display3- Environment friendly R410A refrigerant4- High pressure, low pressure & water flow protection system5- Exceeding low temp auto stop protection6- Temp control compulsory defrosting7- International brand compressor8- Easy installation and operation4
III. Technical -230V/60HzFrequency/phase60Hz/1PhHeating current (air80 F,water80 F)10.8A11.8A15.6 A21.3 AHeating power (air80 F,water80 F)2.3KW2.6KW3.4 KW4.4 KWHeating current (air80 F,water95 F)13.2 A13.3A19 A24.5 AHeating power (air80 F,water95 F)2.7 KW2.9KW3.9 KW5.7 KW11.6A/60.2A12.9A/66.9A21.2A/123A30.2A/139A0.5 A1.1A1.2 A1.2 ADesign pressure (High) 609 PSIG 609 PSIG 609 PSIG 609 PSIGDesign pressure (Low) 261 PSIG 261 PSIG 261 PSIG 261 PSIG56.4oz74.1oz95.2oz116.4oz6878112135Compressor RLA/LRAFan motor ratingRefrigerant (R410A)Net weight (KG)Water circulation flowNoiseWaterproof class83-116 L/min 108-142L/min 108-142 L/min133-167 L/min 50 dB(A) 58 dB(A) 50 dB(A) 58dB(A)IPX4IPX4IPX4IPX4Remarks:1. This product can work well during air temp 32 109 (0ºC to 43 C). Efficiency will not beguaranteed out of this range and parameters are different under various conditions.2. Related parameters are subject to adjustment periodically for technical improvement withoutfurther notice. For details please refer to nameplate.5
IV. 28084658PHCP6539559038742096138077758ModelNote: The picture above is the specification diagram of the pool heater, for technician’s installation and layout referenceonly. The product is subject to adjustment periodically for improvement without further notice.6
V. Installation Guide1. Drawing for water pipes connectionWATER TO SWIMMING POOLwork togetherTHREE WAYVALVESTOP VALVESTOP VALVEPumpOutletSWIMMINGPOOL WATERTREATMENTSYSTEMSTOP VALVEInletTHREE WAYVALVEPOOL WATER INNotice：The drawing is just for demonstration, and layout of the pipes is only for reference.2.Electric Wiring DiagramUsers'Electric BoxTerminal BoardBreaker/fuse(Customer prepare)Power Supply230V/ 60HzL1L2EarthingBondingBreaker/fuse(Customer prepare)Heat PumpcontactorPower Supply230V/ 60HzL1L2BondingEarthingPumpNote：The swimming pool heater must be electrically bonded.7
Options for protecting devices and cable 423030303020253542（ AWG ）3 123 103 103 8Signal cable ( AWG ）3 203 203 203 20Rated currentBreakerARated Residual ActionCurrent mAFuse APower cordNote: The above data is adapted to power cord 10 m .If power cord is 10 m, wire diameter mustbe increased. The signal cable can be extended to 50 M at most.Pump protecting device, cable specification is subject to user’s option.1. Installation instruction and requirementThe swimming pool heater must be installed by a professional team. The users are notqualified to install by themselves, otherwise damage may happen to the heater orthreat the body safety of the user.A．Installation1-The swimming pool heater should be installed in a place with good ventilation;2-The frame must be fixed by bolts (M10) to concrete foundation or brackets. Theconcrete foundation must be solid and fastened; the bracket must be strong enoughantirust treated.3-Please don’t stack substances that will block air flow near inlet or outlet area, andthere is no barrier within 50cm behind the main machine, or the efficiency of theheater will be reduced or even stopped.4-The machine needs an appended pump (Supplied by the user). The recommendedpump specification-flux: refer to Technical Parameter, Max. lift 10m;5-When the machine is running, there will be condensation water discharged from the8
bottom, please pay attention to it. Please hold the drainage nozzle (accessory) into thehole and clip it well, and then connect a pipe to drain the condensation water out.B．Wiring1-Connect to appropriate power supply, the voltage should comply with the ratedvoltage of the products. Bond the machine well to earth.2-Wiring must be handled by a professional technician according to the circuitdiagram.3-Set GFCI (Ground fault circuit interrupter) protector according to the local code forwiring (leakage operating current 30mA).4-The layout of power cable and signal cable should be orderly and not affecting eachother.C．Switch on after finishing all wiring construction and re-checking.VI. Operation InstructionPicture for keys9
Power on/offCLOCKTIME OFFLight ATIME ONLight BCOOLHEATMODE KeyMODESet local time.Set the time required machine auto-stop.Shows the auto-stop time being set.Set the time required machine auto-work.Shows the auto-work time being set.Shows the cool modeShows the heat modeHeat or cool mode selectionDown-ALLOW Set required temperature and timeUP-ALLOW Set required temperature and timeLED screenDisplay time, temperature and machine1. Operation Displaya.The display shows Time when the machine is offb.The display shows Temperature of the swimming pool water when the machine ison.2.Water temperature settinga. Press MODE key can switch HEAT-COOL circulating mode.b. Available no matter the machine is on or off. Press HEAT or COOL light up.c.Press the keyorto set water temperature. The controller indicates twinklingtemp.Pressorto adjust to your desired water temp.d. 5 seconds later, the controller display will back to the normal mode.3. Time settingA. Available no matter the machine is on or off.B. Presskey to set time，when the clock on the screen is twinkling, pressagain to set hour. Useto set minute. Useorto adjust hour. Before the twinkling stops, pressorto adjust. After adjusting，press10and water
temperature will be displayed. 30 seconds later，the controller display will be back tothe normal mode.4. Timer on and offA. Presspressset timer on. When the indicator light is on and the time is twinkling,again to set hour. Usepressto set minute.B. Useororto adjust. Before the twinkling stops,to adjust. After adjusting, pressand water temperaturewill been seen.30 seconds later, the controller display will be back to the normal mode.C. Pressto set timer off. When the indicator light is on and the time istwinkling, pressagain to set hour. Usestop, pressto set minute. Useororto adjust before twinklingto adjust. After adjusting, pressand water temperature will been seen. 30 seconds later, the controller displaywill be back to the normal mode.5. Cancel timer on and offPresspressorto cancel timer on and off. When the number is twinkling,when timer indicator light is off and LED shows water temperature, thetimer on and off is canceled. 30 seconds later, the controller display will be back to thenormal mode.VII.Testing1．Inspection before useA．Check installation of the whole machine and the pipe connections according to thepipe connecting drawing;11
B．Check the electric wiring according to the electric wiring diagram; and bondingconnection.Ｃ．Make sure that the main machine power switch is offＤ．Check the temperature setting.E． Check the air inlet and outlet.2．TrialＡ．The user must “Start the Pump before the Machine, And Turn off the Machinebefore the Pump”, or the machine will be damaged.；Ｂ．The user should start the pump, check for any leakage of water; and then setsuitable temperature in the thermostat, and then switch on power supply.Ｃ．In order to protect the swimming pool heater, the machine is equipped with a timelag starting function, when starting the machine, the blower will run 3 minutesearlier than the compressor.D．After the swimming pool heater starts up, check for any abnormal noise from themachine.VIII. Precautions1 AttentionA．Set proper temperature in order to get comfortable water temperature; to avoidoverheating or overcooling.B．Please don’t stack substances that can block air flow near inlet or outlet area, or theefficiency of the heater will be reduced or even stopped.12
C．Please don’t put hands into outlet of the swimming pool heater, and don’t removethe screen of the fan at any time.D．If there are abnormal conditions such as noise, smell, smoke and electrical leakage,please switch off the machine immediately and contact the local dealer. Don’t tryto repair it yourself.E．Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoidfire.F．In order to optimize the heating effect, please install heat preservation insulation onpipes between swimming pool and the heater. During running period of theswimming pool heater, please use a recommended cover on the swimming pool.G．Connecting pipes of the swimming pool and the heater should be 10m, or theheating effect of the heater cannot be ensured.2 . SafetyA．Please keep the main power supply switch far away from the children.B．When a power cut happens during running, and later the power is restored, theheater will start up automatically. So please switch off the power supply when thereis a power cut, and reset temp when power is restored.C．Please switch off the main power supply in lightning and storm weather to preventfrom machine damage that caused by lightning.D．If the machine is stopped for a long time, please cut off the power supply and drainwater clear of the machine by opening the tap of inlet pipe.13
IX. MaintenanceA．“Cut off” power supply of the heater before any examination and repair.B．In winter seasons, please drain water clear of the machine, “cut off” power supplyto prevent any machine damage, and cover the machine body with plastic foil toavoid dust.C．Please clean this machine with household detergents or clean water, NEVERgasoline, thinners or any similar fuel.D. Check bolts, cables and connections regularly.X. Trouble shooting for common faultsFaultyReasonSolutionsMain power is offWait for power to be reinstatedSwitch offSwitch onBurnt out fuseReplace itCircuit breaker drops outSwitch Circuit Breaker back onThere is airBlocked air inletClean out the stemoutlet but theBlocked air outletClean out the stemheating is not3 minutes time lag protectionPlease waitTemperature set too lowIncrease temperature setting accordinglyNot startingsatisfactoryIf the above mentioned faults cannot be solved, please contact the professional and inform modeland detailed faulty condition.Atten: Please don’t disassemble and repair the swimming pool heater by yourself, please leave itto the professionals.14
Failure codeEE 1High pressure protectionEE 2Low pressure protectionEE 3Low water pressure protectionEE 4Over current (3 phase machine)PP 1Pool water temp sensor failurePP 2Exhaust temp sensor failurePP 3Heating coil pipe temp sensor failurePP 4Gas return temp sensor failurePP 5Air temp sensor failurePP 6Compressor exhaust overload protectionPP 7When the temperature 32 , auto stop protection（not Failure）EE8/888/Abnormal Communication failureXI. ServiceFor service and warranty, contact:Phone Number: 1-888-238-7665XII. WarrantyRegister warranty online at www.nautyl.ca15
XIII. Exploded Diagram – PHCP5016
XIII. Exploded Diagram – PHCP6517
Exploded Diagram – PHCP8018
Exploded Diagram – PHCP11019
Thermopompe pour piscineMANUEL D’INSTALLATION ETD’UTILISATIONPHCP50PHCP65PHCP80PHCP1101Rev 3 Dec 16
Table des matièresI. Utilisation . 4II. Caractéristiques. 4III. Paramètres techniques . 5IV. Dimensions . 6V. Guide d’installation . 7VI. Instruction pour le fonctionnement . 10VII. Vérifications . 12VIII. Précautions. 13IX. Entretien . 15X. Dépannage en cas de problèmes communs . 16XI. Service . 17XII. Garantie . 17XIII. Schémas éclatés et listes de pièces . 182
Avertissement1. N’UTILISEZ PAS cet appareil pour toute autre utilisation que celle de réguler latempérature de l’eau d’une piscine. Toute autre utilisation annulera la garantie.2. Les joints de raccordement de l’entrée et de la sortie ne peuvent supporter le poids detoute autre partie du système de la tuyauterie.3. Assurez-vous que la sortie d’air ne blesse pas quelqu’un, un animal ou une plante.4. Avant d’inspecter ou de réparer l’appareil, assurez-vous d’avoir coupé le courant.Précautions1. L’appareil doit être installé et entretenu par un technicien spécialisé. Le circuitélectrique doit être conforme aux règlements locaux qui s’appliquent. Veuillez lireattentivement le manuel.2. Réglez adéquatement la température afin d’obtenir la température de l’eau souhaitée.3. Assurez-vous que la circulation de l’air près de l’entrée et de la sortie n’est pasobstruée.4. Dès que l’appareil est sous tension, il démarre automatiquement, même s’il avait étéarrêté alors qu’il fonctionnait.5. Si l’appareil ne fonctionne pas pour une longue période de temps ou durant l’hiver,coupez l’alimentation électrique et drainez l’eau de l’appareil en ouvrant le robinetau tuyau d’entrée.6. Ne placez pas votre main ou tout objet dans la sortie d’air de l’évaporateur. Il estinterdit de démonter un ventilateur qui fonctionne.7. Si vous remarquez tout état anormal, comme une odeur ou un bruit anormal, de lafumée ou un courant de fuite, veuillez immédiatement couper le courant et3
communiquez avec votre détaillant local. Ne vérifiez pas l’appareil vous-même.8. N’entreposez pas du matériel combustible ou inflammable près de l’appareil.I. Utilisation1. Réglez la température de l’eau de façon efficace et économique afin d’êtreconfortable et d’en profiter.2. L’utilisateur peut choisir les paramètres techniques du modèle selon le guideprofessionnel. Cette gamme de chauffe-piscines a été optimisée en usine (consultezle tableau des paramètres techniques).II. Caractéristiques1. Échangeur thermique haute efficacité en titane2. Contrôle de la température sensible et précis et afficheur de température de l’eau3. Réfrigérant respectueux de l’environnement R410A4. Systèmes de protection contre la basse et la haute pression et le débit d’eau5. Protection et arrêt automatique en cas de trop basse température6. Contrôle de température pour le dégivrage obligatoire7. Compresseur de marque internationale8. Installation et utilisation facile4
III. Paramètres 08 – 230 V/60HzFréquence/phaseCourant de chauffage60Hz/1 Ph10,8 A11,8A15,6 A21,3 A2,3 KW2,6KW3,4 KW4,4 KW13,2 A13,3A19 A24,5 A2,7 KW2,9KW3,9 KW5,7 KW11,6 A/60,2 A12,9A/66,9A21,2 A/123 A30,2 A/139 A0,5 A1,1A1,2 A1,2 APression de calcul (haute) 609 PSIG 609 PSIG 609 PSIG 609 PSIGPression de calcul (basse) 261 PSIG 261 PSIG 261 PSIG 261 PSIG56,4 oz74.1oz95,2 oz116,4 oz687811213583-116 L/min108-142L/min108-142 L/min133-167 L/min 50 dB (A) 58 dB(A) 50 dB (A) 58 dB (A)IPX4IPX4IPX4IPX4(air 80 F [ 27 C], eau 80 F [ 27 C])Puissance de chauffage(air 80 F [ 27 C], eau 80 F [ 27 C])Courant de chauffage(air 80 F [ 27 C], eau 95 F [35 C])Puissance de chauffage(air 80 F [ 27 C], eau 95 F [35 C])Compresseur RLA/LRACaractéristique nominale dumoteur du ventilateurRéfrigérant (R410A)Poids net (kg)Débit de circulation de l’eauBruitÉtanche, classe de protectionRemarques :1. Ce produit fonctionne bien dans des conditions où la température de l’air se situe entre 32 et109 F (0 et 43 C). L’efficacité de cet appareil ne peut être garantie si la température se situe àl’extérieur de cet intervalle. De plus, les paramètres varient selon les co
1- Set swimming pool water temp efficiently and economic ally to provide you comfort and pleasure . 2- User may choose the model technical parameter according to professional guide, this series of swimming pool heater has been optimized in factory (refer to technical parameter table). II. Features . 1- High efficient titanium heat exchanger
The term "swimming pool" means any artificial basin of water constructed, installed, modified or improved for the purpose of swimming, wading, diving, recreation or instruction. Depending upon the location of the swimming pool the swimming pools can be named as roof top swimming pool, on ground swimming pool and underground swimming pool.
I2 NWI Sox Fossey I4 Team PA Larcinese J2 NKY Bandits Premier J4 Team Ohio Gray K2 Indy Dreams Gold Lewis K4 Steel City Cyclones Cox L2 Motor City Madness Collins L4 WV Firestix Haynes 9:30 POOL 14UP POOL GAME 1 POOL 14UP POOL GAME 1 POOL 14UP POOL GAME 1 POOL 14UP POOL GAME 1 POOL 14UP POOL GAME 1 POOL 14UP POOL GAME 1 POOL 14UP POOL GAME 1 .
3042f012 dpa pump 3042f022 dpa pump 3042f050 dpa pump 3042f052 dpa pump 3042f062 dpa pump 3042f080 dpa pump 3042f101 dpa pump 3042f102 dpa pump 12 volt 3042f110 dpa pump 3042f150 dpa pump 3042f152 dpa pump 3042f152-r dpa pump 3042f170 dpa pump 3042f171 dpa pump 3042f172 dpa pump 3042f210 dpa pump 3042f212 dpa pump 3042f213 dpa pump 3042f213-r .
Swimming Pool Slab Thickness 150 mm Swimming Pool Vertical Wall Thickness 250 mm 3.2.1 Building Models in the Study Figure 3 shows the plan view of the model without swimming pool. The plan area of the swimming pool is 80 sq. meter height of the pool is 3.3 meter. Fig 3 Plan View of Building Models
A. The swimming pool heat pump must be installed by a qualified electrician. B. To maximize your swimming comfort, set proper heating temperature. C. Don’t put obstacles near the air inlet and outlet of the heat pump. D. This heat pump has power-off memory function. E. When the ambient temperature is below 0 degree, make sure to
improperly managed swimming pool can quickly become a public health hazard. For this reason, the public swimming pool operator must know how to properly operate a pool. This manual is designed as a general source of information about swimming pools. It does not cover every aspect of swimming pool operations, but provides the basic information
offer a stronger swimming pool By constructing all layers after the gelcoat colour with Vinyl Ester Resin, Leisure Pools is able to offer a Lifetime Structural Osmosis Warranty A swimming pool is something that should last a long time. Customers spend tens of thousands on a swimming pool project and as a result the swimming pool shell must .
Pool deck equipment Pool main drain piping Pool filter system Pool surge tank Pool water treatment equipment Pool area HVAC system This Report provides a summary of concerns noted and improvement considerations. Photographs may be found in Appendix A for reference. Photos 1 and 2 provide an overall view of the pool room.
