3500/65 16-Channel Temperature Monitor

3y ago
42 Views
2 Downloads
310.91 KB
6 Pages
Last View : 1m ago
Last Download : 2m ago
Upload by : Sabrina Baez
Transcription

3500/65 16-Channel Temperature MonitorBently Nevada* Asset Condition MonitoringDescriptionThe 3500/65 monitor provides 16 channels of temperature monitoring andaccepts both resistance temperature detector (RTD) and isolated tipthermocouple (TC) temperature inputs. The monitor conditions these inputs andcompares them against user-programmable alarm setpoints.The monitor is programmed using the 3500 Rack Configuration Software. Youcan configure the 16-Channel Temperature Monitor to accept isolated tipthermocouples, 3-wire RTD, 4-wire RTD, or a combination of TC and RTD inputs.In Triple Modular Redundant (TMR) configurations, you must install temperaturemonitors in groups of 3 adjacent monitors. In this configuration the monitor uses2 types of voting to ensure accurate operation and to avoid single-point failuresCUSSpecifications and Ordering InformationPart Number 172930-01Rev. D (12/11)Page 1 of 6

Specifications120 Ω 3-wire and 4wire nickel RTD:Inputs-80 C to 260 CSignal(-112 F to 500 F).Accepts from 1 to 16 RTD orisolated tip TC transducer signals.10 Ω 3-wire and 4wire copper RTD:InputImpedance-100 C to 260 C,Greater than 1 MΩ for each leadinput.PowerConsumption(-148 F to 500 F).Note:Platinum RTDs with α 0.00385 are the worldwideindustrial standard and are the recommended RTDs for allapplications.Outputs3 watts nominal.TransducersFront PanelLEDsOK LEDTCsIndicates when the temperaturemonitor is operating properly.Type E-100 C to 1000 C,(-148 F to 1832 F).TX/RX LEDIndicates when the temperaturemonitor is communicating withother modules in the 3500 rack.Type J0 C to 760 C(32 F to 1400 F).Bypass LEDIndicates when the temperaturemonitor is in Bypass Mode.Type K0 C to 1370 C(32 F to 2498 F).RTD CurrentSource Value913 7 µA @ 25 C pertransducer (1 supply for the 4wire RTD and 2 supplies for the 3wire).Type T-160 C to 400 C,(-256 F to 752 F).Signal ConditioningRTDsSpecified at 25 C ( 77 F). Fullscale range for each channel isset in the field via 3500Configuration Software. Nocalibration is required.100 Ω 3-wire and 4wire platinum RTD(α 0.00385):-200 C to 850 C(-328 F to 1562 F).100 Ω 3-wire and 4wire platinum RTD(α 0.00392):RTDs and TCsResolution1 C or 1 F.-200 C to 700 C(-328 F to 1292 F).Specifications and Ordering InformationPart Number 172930-01Rev. D (12/11)Page 2 of 6

AccuracyDanger DelayFrom 1 to 60 seconds in0.5-second increments or set tothe minimum alarm delay of 225mS.InternalTerminationBulkhead Rack: 3 C at 25 C( 5.4 F at 77 F).Standard Rack: 3 C at 25 C( 5.4 F at 77 F).ExternalTerminationBulkhead Rack: 3 C at 25 C( 5.4 F at 77 F).Standard Rack: 3 C at 25 C( 5.4 F at 77 F).Cold Junction CompensationSensor (used for TCmeasurements) 2 C at 25 C( 3.6 F at 77 F).Proportional ValuesProportional values are temperature measurementsused to monitor the machine. The 16-channeltemperature monitor returns temperatureproportional values.Environmental LimitsOperatingTemperature-30 C to 65 C (-22 F to 150 F).StorageTemperature-40 C to 85 C (-40 F to 185 F).AlarmsAlarmSetpoints:You can use softwareconfiguration to set Alert andDanger setpoints for the valuemeasured by the monitor. Alarmsare adjustable from 0 to 100% offull-scale for each measuredvalue. The exception is when thefull-scale range exceeds therange of the sensor. In this case,software will limit the setpoint tothe range of the sensor. Accuracyof alarms are to within 0.13% ofthe desired value. The 3500/6516-channel temperature monitorhas both under- and over-alarmsetpoints.Alarm TimeDelaysCompliance and CertificationsEMCStandards:EN 61000-6-2 Immunity for Industrial EnvironmentsEN 55011/CISPR 11 ISM EquipmentEN 61000-6-4 Emissions for Industrial EnvironmentsEuropean Community Directives:EMC Directive 2004/108/ECElectrical SafetyStandards:EN 61010-1European Community Directives:2006/95/EC Low VoltageHazardous Area ApprovalsYou can use software to programalarm delays as follows:Alert DelayNorth AmericanApproval Option (01)Class 1, Div 2From 1 to 60 seconds in 1-secondincrements.Groups A, B, C, DT4 @ Ta -20 C to 65 ºC(-4 ºF to 150 ºF)Specifications and Ordering InformationPart Number 172930-01Rev. D (12/11)Page 3 of 6

I/O ModulesNorth AmericanApproval Option (02)Ex nC[L] IICDimensions(Height x Widthx Depth)241.3 mm x 24.4 mm x 99.1 mmClass 1, Zone 2Class 1, Div 2, Groups A, B, C, DT4 @ Ta -20 C to 65 ºC(-4 ºF to 150 ºF)ATEX:(9.50 in x 0.96 in x 3.90 in).Weight0.45 kg (1.0 lb.).Rack Space RequirementsMonitor Module:Approval Option (02)1 full-height front slot.For Selected Ordering Optionswith ATEX/North Americanagency approvals:II 3/(3) GI/O Modules:1 full-height rear slot.Ordering ConsiderationsEx nC[L] IICGeneralT4 @ Ta -20 C to 65 ºCIf you add the 3500/65 to an existing 3500 Systemyour system will require the following or laterfirmware and software versions:(-4 ºF to 150 ºF)South Africa3500/22 ModuleFirmwareApproval Option(02)For Selected Ordering Optionswith ATEX/North Americanagency approvals:Revision 1.503500/01SoftwareVersion 3.85Ex nCAL [ia] IIC T4Ex nCAL [L] IIC T4T4 @ Ta -20 C to 65 C(-4 F to 150 F)For further certification and approvals information please visit thefollowing website:www.ge-mcs.com/bently3500/02SoftwareNot supported*3500/03SoftwareNot supported*3500/93 ModuleFirmwareMonitor ModuleRevision 2.02Dimensions(Height x Widthx Depth)System 1*Software241.3 mm x 24.4 mm x 241.8 mm(9.50 in x 0.96 in x 9.52 in).WeightRevision 5.2 with Service Pack 2*Attempting to use the 3500/65 with 3500/02 or 3500/03software may prevent proper operation of the software.0.91 kg (2.0 lb.).Specifications and Ordering InformationPart Number 172930-01Rev. D (12/11)Page 4 of 6

You cannot use external termination blocks withinternal termination I/O modules.When ordering I/O Modules for use with 4-WireRTDs, order with Modification 179952-01. For furtherinformation, see the 3500/65 Manual.000500070010002500500100B: Assembly Instructions0102Ordering InformationSparesWhen ordering I/O Modules with externalterminations, you must order the externaltermination blocks and cables separately.3500/65-AXX-BXXA: I/O Module Type5 feet (1.5 metres)7 feet (2.1 metres)10 feet (3 metres)25 feet (7.5 metres)50 feet (15 metres)100 feet (30.5 metres)Not AssembledAssembled172931-013500/65 Manual.0102RTD/Isolated Tip TC withInternal TerminationsRTD/Isolated Tip TC withExternal TerminationsB: Agency Approval Option00None01CSA/NRTL/C02CSA/ATEX145988-023500/65 Monitor.172103-013500/65 RTD/Isolated Tip TC I/OModule, Internal Terminations173005Connector Header, InternalTermination, 20-position, BlackNote: Agency Approval Option B 02 is onlyavailable with Ordering Option A 01.External Termination Block172109-013500/65 RTD/ Isolated Tip TC I/OModule, External Terminations172115-01RTD/Isolated Tip TC ExternalTermination Block (Euro Styleconnectors).Cables172115-01RTD/Isolated Tip TC ExternalTermination Block (Euro StyleConnectors)3500/65 Transducer (XDCR) Signal to ExternalTermination (ET) Block Cable134544-AXXXX-BXXA: Cable LengthSpecifications and Ordering InformationPart Number 172930-01Rev. D (12/11)Page 5 of 6

Graphs and Figures1.Status LEDs2.3500/65 Main Module Front View3.RTD/ Isolated Tip TC I/O Module (Internal Terminations)4.RTD/ Isolated Tip TC I/O Module(External Terminations)Figure 1: Front and rear views of the 3500/65 16 Channel Temperature Monitor* Denotes a trademark of Bently Nevada, Inc., a wholly owned subsidiary of General Electric Company. 2006 – 2011 Bently Nevada, Inc. All rights reserved.Printed in USA. Uncontrolled when transmitted electronically.1631 Bently Parkway South, Minden, Nevada USA 89423Phone: 775.782.3611Fax: 775.215.2873www.ge-mcs.com/bentlySpecifications and Ordering InformationPart Number 172930-01Rev. D (12/11)Page 6 of 6

3500/65 16-Channel Temperature Monitor . Bently Nevada* Asset Condition Monitoring . Description . The 3500/65 monitor provides 16 channels of temperature monitoring and accepts both resistance temperature detector (RTD) and isolated tip thermocouple (TC) temperature inputs. The monitor conditions these inputs and

Related Documents:

3500/61E & 3500/67E Temperature Monitor . Bently Nevada* Asset Condition Monitoring . 3300/35 6. with the I/O modules used for the 3300/36 2. Description . The 3500/61E and 3500/67E modules provide six channels and two channel of temperature monitoring. Both monitors can be ordered to accept Resis tance

Maserati- 3500 GT Coupe Touring- Engine 9 Maserati- 3500 GT Coupe Touring- Exhaust 11 Maserati- 3500 GT Coupe Touring- Fuel System 12 Maserati- 3500 GT Coupe Touring- Glass and Seals 13 Maserati- 3500 GT Coupe Touring- Interior 18 Maserati- 3500 GT Coupe Touring- Lights 20 Maserati- 3500 GT Coupe Touring- Luggage Compartment 22

125 crf125f/fb je03e 3500 3500 3500 3500 3500 trx250tm/te te21e, te48e 3250 3250 3250 3250 150 CRF150F KE02E 4250 4250 4250 4250 400 TRX400X TE23E 3500 CRF150R*/ RB* KE03E 6250 6250 6250 6250 6250 420 TRX420FA/FPA TE37E 3250

Bently Nevada* Asset Condition Monitoring 3500/05 System Rack . Description . The 3500 System rack design holds all 3500 monitor modules and rack power supplies. It allows the various 3500 modules to communicate with one another and the power supplies to distribute power to each mod ule as required. 3500 Racks are available in two sizes: 1.

Catalyst 3500 XL Cisco Cisco Catalyst 3500 XL 2900 XL Catalyst 1900 & &' IP 380 &' Gigabit Ethernet&' &' Catalyst 3500 XL&' Cisco IOS( Cisco Visual Switch Manager (CVSM) &' Web Cata-lyst 3500 XL&' * &' * 802.1Q ISL VLAN TACACS Uplink Fast Catalyst 3500 XL 3 Cisco GigaStack( Gigbit Interface Converter (GBIC)

AS/NZS 3500 Plumbing and drainage AS/NZS 3500.0 - Glossary of terms AS/NZS 3500.1 - Water services AS/NZS 3500.2 - Sanitary plumbing and drainage AS/NZS 3500.3 - Stormwater AS/NZS 3500.4 - Hot water supply systems AS 4032 Water Supply - Valves for the control of

A biotech project involves a pioneer venture stage to first prove the new technology in order to establish its viability for future commercial development of spin-off products. The pioneer venture involves high initial costs and insufficient projected cash inflows. If the technology . Depr 3500 3500 3500 3500 3500 3500 EBT -100 47 221 376 510 690

Anatomy and physiology for microblading techniques Unit reference number: L/615/6166 Level: 4 Guided Learning (GL) hours: 20 Overview The aim of this unit is to provide learners with the necessary underpinning knowledge of relevant human anatomy and physiology to enable them to perform effective and safe microblading services for eyebrow treatments. Learners will develop an understanding of .