204-04 : Wheels And Tires - DISCO3.CO.UK
204-04 : Wheels and TiresSpecificationsWheelsWheel typeAlloy wheelAlloy wheelAlloy wheelReduced size spare wheel - SteelWheel size7J x 178J x 188J x 195.5J x 19CAUTION: With reduced size spare wheel fitted, do not exceed 80 km/h and replacewith standard size wheel at earliest opportunity.CAUTION: Do not use power tools when operating the spare wheel winch, raise andlower winch manually using hand tools only.Tire Sizes - Standard FitWheel size7J x 17 - Alloy8J x 18 - Alloy8J x 19 - AlloyTire size235/70 R17H - All terrain255/60 R18H or V - All terrain255/55 R19H or V - All terrainTire load index111112111CAUTION: Inner tubes must not be fitted with any of these tires.Tire Sizes - Accessory FitWheel size8J x 19 - Alloy8J x 19 - AlloyTire size255/55 R19 - Mud terrain255/55 R19 - SandTire load index111111CAUTION: Inner tubes must not be fitted with any of these tires.Tire Pressures - Not NAS VehiclesLoading conditionNormal operating conditions - Up to 4 people:Frontbars lbf/in²kPa2.323033
RearVehicle loaded to maximum gross vehicle weight:FrontRearReduced size spare wheel* Standard size spare ON: * The standard size spare wheel tire should be inflated to the maximumgross vehicle weight pressure and the pressure for the front or rear wheel locationsmust be adjusted accordingly if the wheel is to be used under conditions other thanwith the vehicle loaded to maximum gross vehicle weight.Tire Pressures - NAS VehiclesLoading conditionAll conditions - Vehicle loaded up to maximum gross vehicle weight:FrontRearReduced size spare wheel* Standard size spare wheelbars lbf/in² kPa2.32.94.22.933426042230290420290CAUTION: * The standard size spare wheel tire should always be inflated to thehighest loading condition pressure which must be adjusted accordingly if the wheelis to be fitted to the front wheel locations.General SpecificationItemMake LocationTire low pressureSiemens On inside of wheel rimsensorTire pressure sensorinitiator:Attached to the fender splash shield adjacent to the frontFrontSiemensbumperAttached to the fender splash shield adjacent to the rearRearSiemensbumperAttached to the roof panel between the sun roofs, on theModuleSiemensleft hand side of the interior lightRecommended LubricantApplicationLand Rover Part No.
Wheel hub spigotRYL 105020Torque SpecificationsDescription* Road wheel nutsTire low pressure sensorNm lb-ft140 10364Wheels and TiresGENERALA number of alloy wheel and tire size combinations are available. A Tire PressureMonitoring System (TPMS) is also available. This system monitors the pressure in eachtire and informs the driver if the pressure is outside predetermined thresholds.WHEELSItemABCDEPart Number-Description7JX178JX18 - Style 18JX18 - Style 28JX195.5JX19 - Space saverThere are a number of different alloy wheel styles as follows:
7J X 17' - one style 8J X 18' - two styles 8J X 19' - one styleThe spare wheel fitted to all vehicles is a steel space saver wheel. The wheel size is 5.5JX 19 and uses a T175/80R19 tire. The space saver wheel is a standard fitment for allmarkets except Gulf states. A full size spare is offered as an optional fitment.TIRESTires are available in a number of sizes and tread patterns dependent on the vehicleusage. Tire sizes are as follows: 235/70R17 255/60R18 255/55R19.The following tires are available; All Season (AS), All Terrain (AT) and All Terrain Sport (AT-S).NOTE:Tires should be inflated to the recommended pressures (as given in the ownershandbook) only when the tires are cold (ambient temperature). If the tires have beensubjected to use or exposed to direct sunlight, move the vehicle into a shaded positionand allow the tires to cool before checking and/or adjusting the pressures.SpecificationsAir Suspension - General SpecificationItemSpecificationRide height:Off road55 mm above standardAccess - reselectable50 mm below standardwhilst vehicle is movingTrim heightConfigured using T4 plus special toolsHeight sensors:Location4 per vehicle - one sensor for each wheelHeight sensor arm colourcoding:Left hand side, front andWHITErearRight hand side, frontBLACKand rearHeight sensor operating
voltages:Supply voltageOutput voltageSpring/damper modules:TypePressures:Normal - FrontNormal - RearBurst pressureMaximum springpressure - Full bump atgross vehicle weightAir compressor:Controlled byMaximum pressureAir reservoir:VolumeWorking pressureMaximum operatingpressureReservoir valve block5 volts - supplied by air suspension ECULeft hand front and right hand rear - Decreases to 0.5 volts withbump travel. Right hand front and left hand rear - Decreases to4.5 volts with bump travelGuided air spring surrounding twin tube damper800 to 1000 kPa (8.0 to 10.0 bar) (116.0 to 145.0 lbf/in²)500 to 800 kPa (5.0 to 8.0 bar) (72.5 to 116.0 lbf/in²)3500 kPa (35 bar) (507.5 lbf/in²)Approximately 2700 kPa (27 bar) (391.5 lbf/in²)Supplied with air drier, electrically switched, pilot operatedexhaust valve and double temperature sensorsECU1680 kPa (16.8 bar) (243.6 lbf/in²)9 litres (0.31 cu.ft)1750 kPa (17.5 bar) (253.75 lbf/in²)2300 kPa (23 bar) (333.5 lbf/in²)Incorporates pressure sensor to monitor spring and air reservoirpressuresValve blocks:FrontRear2 corner valves, 1 cross link valve - all mounted on frontbumper armature2 corner valves, 1 cross link valve - all mounted on left handrear spring towerVehicle Dynamic SuspensionOn-Road ModeThis is the normal ride height for the vehicle.Off-Road ModeOff-road mode will only be activated if the vehicle speed is less than 40 km/h. Thevehicle will be raised 55 mm higher than the on-road mode to provide additional bodyclearance and improved approach, departure and breakover angles. If the vehicle speedexceeds 50 km/h, the air suspension control module will automatically lower the vehicleto the on-road mode height. At 40 to 45 km/h a message is displayed in the message
center to warn the driver to slow down or the vehicle will lower.NOTE:The suspension can be automatically set to off-road mode when some TerrainResponse programs and low range are selected.Access ModeAccess mode lowers the vehicle body height by 50 mm and provides easier entry, exitand loading of the vehicle. Access mode can be pre-selected when the vehicle is moving.The vehicle will partly lower as the vehicle speed decreases, lowering to the full accessmode height when the vehicle reaches 8 km/h. If the required road speed is not reachedwithin a predetermined time, the air suspension will return the vehicle to the previouslyselected height.Access mode can be selected at any vehicle speed. When access mode is selected, theresponse of the air suspension system will depend on the vehicle speed: If the vehicle speed is more than 20 km/h, the air suspension control module willwait for up to one minute for the vehicle speed to be reduced. The access modelamp and the lowering lamp will flash while the air suspension control modulewaits for the vehicle speed to be reduced, the on-road mode lamp will remainilluminated. If the vehicle speed is not reduced sufficiently, the access moderequest will be cancelled after 1 minute. If the vehicle speed is less than 20 km/h, the air suspension control module willlower the suspension to a part lowered height and will remain at this height for upto one minute. The on-road mode lamp will extinguish as the air suspensioncontrol module lowers the suspension to the part lowered height. The access modelamp and the lowering lamp will illuminate. When part lowered is reached, the'lower' lower lamp will flash. If the vehicle speed is not reduced to less than 8km/h in the one minute period, the access mode request will be cancelled. If the vehicle speed is less than 8 km/h, the suspension will be lowered to accessmode immediately. The access mode lamp and the lowering lamp will illuminate.When the access mode height is reached, the lowering lamp will be extinguished.Access height may be selected up to 40 seconds after the ignition is turned off,providedthat the driver's door has not been opened within this time.The suspension will automatically rise from access mode when the vehicle speed exceeds10 km/h. If access mode was selected directly from off-road mode then the system willreturn to off-road mode when the vehicle speed exceeds 10 km/h. Otherwise the systemwill lift the suspension to On-road height.Selecting Access Mode Directly from Off-Road Mode
When the suspension is in off-road mode height, pressing the air suspension switch onceand then a second time before the lowering lamp is extinguished, the control module willlower the suspension to access mode height. The control module will remember to returnthe suspension to off-road height automatically if the vehicle speed increases above 10km/h.Crawl (Locked at Access) ModeCrawl mode allows the vehicle to driven at access height. The vehicle is locked in accessheight and can be selected at a speed of less than 35 km/h and can be driven at lowspeeds to improve clearance in areas with restricted headroom, i.e. car parks. If thevehicle exceeds 40 km/h, crawl mode will be cancelled and the vehicle will return to onroad height.Crawl mode allows the vehicle to be driven at low speeds with the suspension locked atthe access mode height. This allows the vehicle to be driven in low car parks etc. withincreased roof clearance.Crawl mode can be selected up to 35 km/h with a long press of the switch in the downdirection. The access mode lamp and the crawl mode lamp will be illuminated. When thecontrol module is in crawl mode, on-road mode height will be selected automatically ifthe vehicle speed exceeds 40 km/h. At 30 to 35 km/h a message is displayed in themessage center to warn the driver to slow down or the vehicle will raise. Crawl mode canalso be manually cancelled by moving the switch in the up direction for 1 second. Theaccess mode lamp and the crawl mode lamp will be extinguished.Automatic Height Change WarningsWhen the suspension is in off-road mode, access mode or crawl mode height, the airsuspension control module will change the suspension height automatically when thevehicle speed exceeds a predetermined threshold.When the suspension is at off-road mode or crawl mode height, the control module issuesa warning to advise the driver that the vehicle is approaching the speed threshold. Theinstrument cluster sounder will emit a chime, a message will be displayed in the messagecenter and the on-road mode lamp and either the raising or lowering lamp will flash.The off-road mode or crawl mode height speed warning is removed when the vehiclespeed is reduced.
SPECIAL MODESDoor Open FunctionalityIf one or more of the vehicle doors are opened during a height change when the vehicle isstationary, the air suspension control module will restrict further height change. The dooropen signal is transmitted by the CJB on the high speed CAN bus and received by the airsuspension control module. This keeps the vehicle level to the set height when a dooropens to allow for changes in loading conditions.A hardwired door status signal is also transmitted from the CJB to the air suspensioncontrol module. This signal provides door status information when the high speed CANbus is off, i.e.; during periodic re-levelling.The lamp on the air suspension switch for the target mode height will remain illuminatedand the raising or lowering lamp will flash.If all of the doors are closed within 90 seconds, the height change will resume. If the 90second period is exceeded and all of the doors are not closed, the height change will becancelled. The mode lamps showing the previously selected height and the target heightwill be illuminated. The mode height change can be reselected by operating the switch,however, if the vehicle is driven at speed of more than 5 mph (8 km/h) the controlmodule will continue to raise or lower the vehicle to the target mode height.Extended ModeIf the vehicle becomes grounded and the traction control becomes operational, the airsuspension control module automatically increases the mass of air in the air springs toraise the vehicle clear of the obstruction. Extended mode is activated automatically andcannot be selected manually.When the air suspension control module has activated the extended mode, the off-roadmode lamp will flash if the suspension is above off-road mode height. The off-road modeand on-road mode lamps will flash if the suspension is between off-road mode and onroad mode heights. The on-road mode and access mode lamps will flash if the suspensionis between on-road mode and access mode. A message will also be displayed in themessage center.To exit the extended mode, press the air suspension switch briefly in the up or downposition or drive the vehicle at a speed of more than 20 km/t.Suspension Prevented From MovingIf the air suspension control module is attempting to change the suspension height and itdetects that the suspension is prevented from moving, the control module will stop allsuspension movement. This can be caused by jacking the vehicle, attempting to lower the
vehicle onto an object or raising the vehicle against an obstruction.The air suspension switch lamps operate as described for extended mode and the samemessage is displayed in the message center. To start the air suspension system operating,press the air suspension switch briefly in the up or down position or drive the vehicle at aspeed of more than 20 km/h.Periodic Re-levellingWhen the vehicle is parked, the air suspension control module 'wakes up' two hours afterthe ignition was last switched off and then once every six hours. The vehicle height ischecked and if the vehicle is not level within a pre-set tolerance, small downwards heightadjustments may be made automatically.Engine - 2.7L DieselGeneral SpecificationsItemSpecification2.7 litre, 60 degree 'V', common rail direct injection, turbocharged andTypeintercooled diesel, twin overhead camshafts, 4 valves per cylinderCylinderV6, numbers 1 and 4 cylinders at front of engine when engine is viewedarrangement from rearCylinderNumber 1 cylinder - right hand bank; Number 4 cylinder - left hand banknumberingBore 81·0 mm (3·188 in)nominalStroke88·0 mm (3·464 in)Capacity2720 cm³ (165·9 in³)Firing order 1 - 4 - 2 - 5 - 3 - 6Compression17.3:1ratioDirection ofAnti-clockwise viewed from rear of enginerotationMaximum147 Kw (200 PS) (197 bhp) @ 4000 rev/minpowerMaximum440 Nm (324 lb-ft) @ 1900 rev/mintorque
Instrument Cluster - /No charge warning indicatorLow oil pressure warning indicatorMalfunction Indicator Lamp (MIL)Seat belt warning indicatorSRS warning indicatorAdaptive Cruise Control (ACC) indicator (if fitted)Left turn signal indicatorCoolant temperature gageHigh coolant temperature warning indicatorHigh beam indicatorTyre pressure monitoring system indicator (if fitted)
373839-Fuel level gageRight turn signal indicatorCruise control indicatorAdaptive front lighting system indicator (if fitted)Park brake fault indicatorPark brake warning indicatorFront fog lamp indicatorRear fog lamp indicatorSpeedometerOdometerTrip meter displayTrip reset buttonSelector lever position (automatic transmission only)CommandShift /Sport mode indicatorCommandShift gear position (automatic transmission only)Trailer indicatorLow fuel indicatorMessage centerABS indicatorBrake warning indicator (pad wear/low fluid/EBA/EBD)Auxiliary heatingDSC/traction control indicatorHDC active indicatorAmbient light sensorAlarm indicatorTransfer box low range indicatorAir suspension warning indicatorTachometerWARNING INDICATORSThe warning indicators are located in various positions in the instrument cluster. Thewarning indicators can be split into two groups; self controlled and externally controlled.Self controlled warning indicators are dependent on software logic within the instrumentpack for activation. The pack software controls the indicator check illumination atignition on and all indicators whose operation is controlled by the instrument cluster, thelow fuel level warning indicator for example.Externally controlled indicators are supplied with current from another system controllingmodule or illuminated by the instrument cluster on receipt of a bus message from anothersubsystem module.Some indicators are activated by an external subsystem module but the instrument clustercontains the control logic. These indicators are shown in the following table as being bothself and externally controlled.
The following table shows the available indicators and indicates if they are subject to anindicator check at ignition on and if they are self or externally controlled.IndicatorIlluminationColorIgnition/No chargeLow oil pressureRedRedGlow plug activeAmberMILSeat beltSRSAdaptive cruise control (iffitted)Transfer box low rangeAir suspensionHDC activeHDC faultDSC / Traction controlLeft turn signalRight turn signalTrailerHigh engine coolanttemperatureHigh beamABS failureLow fuel levelCruise controlPark Brake City modePark brake faultPark brake warningFront fog lampsRear fog lampsAlarmEMS FaultDriveline faultDriveline overheatLow washer fluidDoor openFBH activeTyre pressure monitoringBulb CheckSelf Controlled(S)/ExternallyControlled (E)AmberRedRedNoNo* No (will illuminate atignition on to show glowplugs active)* YesNo* YesEEEEEAmberNoEEGreenNoAmber / Red EEEEEREDSYesBlueNoAmber* oAmberNoRedNoAmberYesAmber / Red EEEE
Low coolant levelOverspeedWater in fuelTyre pressure warningBrake warningAdaptive front lighting* Bulb check performedby subsystem module, notinstrument clusterAmberNoAmberNoNonfunctionalAmberYesAmber / Red YesAmberYesEEEEEWarning Indicator FunctionalityItem Part Number12345678910111213-DescriptionAir suspensionTransfer box low rangeHDC activeDSC/Traction controlIgnition/No chargeLow oil pressureGlow plugs active (diesel models only)Malfunction Indicator Lamp (petrol models only)SRS warningLeft turn indicatorRight turn indicatorHigh beamTyre pressure monitoring system
39-Seat belt warningBrake warningABSCruise controlAdaptive front lighting systemPark brake fault (all except NAS)Park brake warning (all except NAS)Front fog lampsRear fog lampsTrailerAuxiliary heatingEngine management system faultDriveline faultHDC faultWater in fuel (non-functional)Driveline overheatLow washer fluidDoor openPark brake city mode (non-functional)Tyre pressure warningLow coolantOverspeed warning (Gulf only)Park brake fault (NAS only)Park brake warning (NAS only)Brake warning (NAS only)Adaptive Cruise Control (ACC) (if fitted)The functionality for each of the above warning indicators is described below. Somewarning indicators are accompanied by a chime from the instrument pack when they areilluminated and also a message in the message center on high line instrument clusters.Some indicators are only available on the low line instrument cluster, with the indicatorsbeing replaced with messages on the high line instrument cluster.1. Air Suspension IndicatorThe air suspension indicator is illuminated by the instrument cluster software on receiptof a CAN signal from the air suspension control module. The air suspension controlmodule outputs a number of different signals relating to the air suspension systemoperation. The instrument cluster interprets the signals and can illuminate the indicator ineither an amber or red colour as appropriate. Some signals also include requests forchimes from the instrument cluster to alert the driver.2. Transfer Box Low Range IndicatorThe transfer box low range indicator is illuminated by the instrument cluster software on
receipt of CAN signals from the transfer box control module. When a range change
Application Land Rover Part No. Wheel hub spigot RYL 105020 Torque Specifications Description Nm lb-ft * Road wheel nuts 140 103 Tire low pressure sensor 6 4 Wheels and Tires GENERAL A number of alloy wheel and tire size combinations are available. A Tire Pressure Monitoring System (TPMS) is also available. This system monitors the pressure in each tire and informs the driver if the pressure .
drive & pull wheels, measuring wheels, feed wheels, pinch & nip wheels, as well as support and conveyor wheels. All C130 wheels are dynamically balanced to assure smooth vibration-free operation and may be recovered at a considerable cost savings. Custom wheels are available: Style A Standard design available 6" dia. and up. *other designs .
For current availability of specific sizes and types of tires contact your Goodyear Representative. Construction All tires are reinforced with nylon cords, except Unisteel Radial Ply tires, which are reinforced with steel cords. Dimensional Data Dimensions of tires are for tires on design rims.
Page 2 of 30 IT-204-I (2020) Instructions for Form IT-204 General information Purpose of Form IT-204 Use Form IT-204 to report income, deductions, gains, losses, and credits from the operation of a partnership for calendar year 2020, or other tax year beginning in 2020. All items reported on Form IT-204 or on documents included with it are
Unless otherwise noted, when we refer to rule 203-1, 204-1, 204-2, or 204-3, or any paragraph of these rules, we are referring to 17 CFR 275.203-1, 275.204-1, 275.204-2, or 275.204-3, respectively, of the Code of Federal Regulations in which these rules are published. 1
z7.5J x 16 ET 45 / 12-spoke cast alloy wheels with 215 / 55 all-season tires "Elegant design" - x z7.5J x 17 ET 45 / 6-spoke cast alloy wheels with 235 / 45 all-season tires o o z7.5J x 17 ET 45 / 6-spoke cast alloy wheels with 235 / 45 high performance tires (only in combination w
longer tire life with Bobcat Solid Air and Twin Flex Tires. These tires last at least 3 times longer than pneumatic tires. With a tear strength that is more than double the strength of most pneumatic tires and absolute puncture resistance, you will experience better resistan
Steer Tires Drive Tires Trailer Tires Mixed Service Tires Warranty Table of Contents Page 2 of 3 Page 3 of 3. TIRE SIZE PLY RATING LOAD RANGE SPEED SYMBOL . 2 2021 Truck Tire Data and Reference Book Tubeless Tube Tye Line Haul Wor Regional WARRANTY MIXED SERVICE TRAILER DRIVE STEER Page
All Hoosier DOT tires will also have two additional codes as required by the Department of Transportation. (Example: J7AB 4AX8 3709) CIRCLE TRACK RACING TIRES: (Includes both dirt and asphalt tires) Hoosier tires must be mounted with the serial code located toward the infield. ROAD RACING T
