ConnectX -2 EN Dual Port SFP Ethernet Adapter Card User .
ConnectX -2 EN Dual Port SFP EthernetAdapter Card User ManualP/N:MNPH29C-XSR, MNPH29C-XTR, MNPH29D-XSR, MNPH29D-XTRRev 1.6www.mellanox.com
Rev 1.6NOTE:THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED DOCUMENTATION AREPROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY KIND AND SOLELY FOR THE PURPOSEOF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PRODUCTS IN DESIGNATED SOLUTIONS. THECUSTOMER'S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOXTECHNOLOGIES TO FULLY QUALIFY THE PRODUCTO(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOXTECHNOLOGIES CANNOT AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THEHIGHEST QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT AREDISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT,INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING, BUT NOT LIMITED TO,PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) ANDRELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.Mellanox Technologies350 Oakmead Parkway Suite 100Sunnyvale, CA 94085U.S.A.www.mellanox.comTel: (408) 970-3400Fax: (408) 970-3403Mellanox Technologies, Ltd.PO Box 586 Hermon BuildingYokneam 20692IsraelTel: 972-4-909-7200Fax: 972-4-959-3245 Copyright 2011. Mellanox Technologies. All rights reserved.Mellanox , BridgeX , ConnectX , InfiniBlast , InfiniBridge , InfiniHost , InfiniRISC , InfiniScale , InfiniPCI , PhyX andVirtual Protocol Interconnect are registered trademarks of Mellanox Technologies, Ltd. CORE-Direct and FabricIT are trademarks ofMellanox Technologies, Ltd. All other marks and names mentioned herein may be trademarks of their respective companies.ConnectX-2 Ethernet Card User Manual2Mellanox TechnologiesDocument Number: 3160
ConnectX-2 Ethernet Card User ManualRev 1.6Table of ContentsTable of Contents3List of Figures5List of Tables6Revision History7About this Manual8Intended AudienceRelated DocumentationOnline ResourcesDocument ConventionsTechnical SupportFirmware and Software Updates888889Chapter 1 Overview1.11.21.31.4Chapter 210Adapter Cards Covered in this ManualMellanox Part Numbering LegendFinding the MAC and Serial Number on the Adapter CardsSafety Warnings11131414Adapter Card Interfaces162.12.22.32.4I/O InterfacesPowerMemoryVPD Layout16181819Chapter 3 Driver Software and Firmware22Chapter 43.1 Driver Software3.2 RDMA over Converged Ethernet (RoCE)3.3 Updating Card Firmware3.4 ConnectX EN PXE22222324Ethernet Adapter Card Installation254.14.24.34.425252631Hardware and Software RequirementsInstallation InstructionsSet UpCables and ModulesAppendix A SpecificationsA.1A.2A.3A.434MNPH29D-X[ST]R SpecificationsMNPH29C-X[ST]R SpecificationsBoard Mechanical Drawing and DimensionsEMC Certification Statements34353537Appendix B Interface Connectors PinoutB.1B.2B.3B.440I2C-Compatible Connector PinoutPCI Express x8Connector PinoutPCI Express Connector PinoutSFP Connector Pinout40404141Appendix C Replacing a Tall Bracket With a Short Bracket43C.1 Remove the Existing Bracket from the Adapter CardC.2 Installing the New Bracket4343Appendix D Avertissements de sécurité d’installation (Warnings in French)45Mellanox Technologies3
Rev 1.6Appendix E Sicherheitshinweise (Warnings in German)46Appendix F Advertencias de seguridad para la instalación (Warnings in Spanish)474Mellanox Technologies
ConnectX-2 Ethernet Card User ManualRev 1.6List of FiguresFigure 1:SFP NIC Component Side and Bracket Views12Figure 2:Card Product Label14Figure 3:Port Numbering16Figure 4:LED - Port Association17Figure 5:Physical and Logical Link Indications17Figure 6:I2C Connector18Figure 7:Flash Jumper19Figure 8:Support Download Assistant24Figure 9:Hardware Devices27Figure 10: PCI Device28Figure 11: Module With Locking Mechanism Closed32Figure 12: Module With Locking Mechanism Open32Figure 13: Schematic of the ConnectX-2 Small Form Factor MNPH29D Adapter Card36Figure 14: Schematic of the ConnectX-2 Card MNPH29C Adapter Card37Figure 15: Compatible Connector Plug and Pinout40Figure 16: Rear View of Module With Pin Placement41Figure 17: Remove the Bracket43Figure 18: Putting on the Bracket44Mellanox Technologies5
Rev 1.6List of TablesTable 1:Revision History Table7Table 2:Documents List8Table 3:Network Interface Cards11Table 4:Mellanox Cards Part Numbering Key13Table 5:LEDs17Table 6:Jumper Configuration19Table 7:VPD Layout for MNPH29D-X[ST]R19Table 8:VPD Layout for MNPH29C-X[ST]R20Table 9:Hardware and Software Requirements25Table 10:Specifications for MNPH29D-X[ST]R34Table 11:Specifications for MNPH29C-X[ST]R35Table 12:Adapter Cards Certification Status37Table 13:I2C-Compatible Connector Pinout40Table 14:SFP Connector Pinout426Mellanox Technologies
ConnectX-2 Ethernet Card User ManualRev 1.6Revision HistoryThis document was printed on 2/15/11.Table 1 - Revision History TableDateRevComments/ChangesJan. 20111.6Changed Air flow requirementAdded to the Set up sectionDec. 19th,20101.5Minor formatting changesNov. 22nd,20101.4Added Generation D card Mini Form FactorOct. 28th,20101.3Added Technical Support and Firmware and Software Updates sections to the Preface sectionAdded RoCEAdded ConnectX EN PXEAdded Set up section, This is a sanity check after card installation.Added KCC statement to Appendix AAdded QSFP to SFP QSA adapterRemoved Gen 1 cardsFormatted EMC tableChanged EN 60950-1: 2001 to EN 60950-1: 2006Changed RDMA over EthernetAdded RDMA over EthernetNew templateApril 20101.2New power numbersFeb. 20101.1Added Section on PXE bootFeb. 20101.0Initial ReleaseMellanox Technologies7
Rev 1.6About this ManualThis User Manual describes Mellanox Technologies ConnectX -2 Dual Port 10Gigabit EthernetPCI Express x8 adapter cards. It provides details as to the interfaces of the board, specifications,required software and firmware for operating the board, and relevant documentation.Intended AudienceThis manual is intended for the installer and user of these cards.The manual assumes basic familiarity with Ethernet networks and architecture specifications.Related DocumentationTable 2 - Documents ListMellanox Firmware Tools (MFT) User ManualDocument no. 2204UGUser Manual describing the set of MFT firmware management tools for asingle node.See http://www.mellanox.com Firmware & Downloads DownloadFirmware ToolsOrhttp://www.mellanox.com Support Download Firmware ToolsIEEE Std 802.3 SpecificationThis is the IEEE Ethernet CI Express 2.0 SpecificationsIndustry Standard PCI Express 2.0 Card Electromechanical Specification,Rev 1.3.Online Resources Mellanox Technologies Web pages: http://www.mellanox.com Mellanox Technologies Firmware download Web page:http://www.mellanox.com Document ConventionsWhen discussing memory sizes, MB and MBytes are used in this document to mean size in megabytes. The use of Mb or Mbits (small b) indicates size in mega bits.Technical SupportCustomers who purchased Mellanox products directly from Mellanox are invited to contact usthrough the following methods. URL: http://www.mellanox.com Support E-mail: support@mellanox.com8Mellanox Technologies
ConnectX-2 Ethernet Card User ManualRev 1.6 Tel: 1.408.916.0055Customers who purchased Mellanox M-1 Global Support Services, please see your contract fordetails regarding Technical Support.Customers who purchased Mellanox products through a Mellanox approved reseller should firstseek assistance through their reseller.Firmware and Software UpdatesThe Mellanox support downloader contains software, firmware and knowledge database information for Mellanox products. Access the data base from the Mellanox Support Web page,http://www.mellanox.com Supportor use the following link to go directly to the Mellanox Support Download Assistant llanox Technologies9
Rev 1.61OverviewOverviewThis document is a User Manual for Mellanox Technologies cards based on the ConnectX -2ENintegrated circuit device. The cards described in this manual have the following main features: IEEE Std 802.3 compliant 10 Gb/s Ethernet Dual SFP ports for connection Ethernet traffic PCI Express 2.0 (1.1 compatible) through an x8 edge connector up to 5GT/s Fiber Channel encapsulation (FCoE) RDMA over Converged Ethernet (RoCE) RoHS-R6 Two bracket heights: short and tall10Mellanox Technologies
ConnectX-2 Ethernet Card User Manual1.1Rev 1.6Adapter Cards Covered in this ManualTable 3 lists the Ethernet adapter cards described in this manual.Table 3 - Network Interface CardsOrdering PartNumber (OPN)MNPH29D-XTRPCI ExpressSERDESSpeedData TransmissionRate/# of portsPCIe Gen25.0 GT/s10 10 Gb/sEthernetShort / TallBracketRoHSAdapter IC Part R-TE2 portsMNPH29D-XSRPCIe Gen25.0 GT/s10 10 Gb/sEthernet2 portsMNPH29C-XTRPCIe Gen25.0 GT/s10 10 Gb/sEthernet2 portsMNPH29C-XSRPCIe Gen25.0 GT/s10 10 Gb/sEthernet2 portsMellanox Technologies11
Rev 1.6OverviewFigure 1: SFP NIC Component Side and Bracket ViewsJ1U1MNPH29DJ1MNPH29C12Mellanox TechnologiesU1
ConnectX-2 Ethernet Card User Manual1.2Rev 1.6Mellanox Part Numbering LegendTable 4 describes the Mellanox Technologies adapter cards part numbering legend.Table 4 - Mellanox Cards Part Numbering KeyAdapter HAdapter TypeH InfiniBand Host Channel Adapter, N Ethernet Network Interface CardTMediaP SFP ,SAdapterArchitectureH ConnectX or ConnectX-2## ports1 1, 2 2IHost InterfaceX PCI-X, 4 PCIe x4, 8 PCIe Gen1 x8, 9 PCIe (Gen2 x8),GGeneration blank Initial product generation, B generation B, C generation C-SeparatorXMemory SizeX MemFree, 1 128MB, 2 256MB, 3 512MBBBracketS Short, T Tall, N NoneRRoHS blank non RoHS, C RoHS R-5 w/ Exemption, R RoHS R-6 Lead-FreeFor example, the part number MNPH29C-XTR describes Mellanox Technologies’ ConnectX ENadapter card with two SFP ports, a PCIe2.0 x8 5.0GT/s interface, no on-board memory (memfree), a tall bracket, and RoHS R6 compliance. Using the legend, field M M to indicate a Mellanox Technologies product, field H N to indicate a Network Interface Card, field T P to indicate 10GBASE-SR/LR, field S H to indicate ConnectX field # 2 to indicate two ports, field I 9 to indicate PCI Express 2.0 x8 running at 5.0GT/s, field G C to indicate Generation C ConnectX-2 field X X to indicate no on-board memory, field B T to indicate a tall bracket, and field R R to indicate RoHS R6 complianceMellanox Technologies13
Rev 1.61.3OverviewFinding the MAC and Serial Number on the Adapter CardsAll Mellanox adapter cards have a label on the printed side of the adapter card that has the cardserial number, and the card MAC.Figure 2: Card Product LabelS/N:MT0744X00012REV: X1P/N:MNPH29C-XTRMAC: 0002C9020040DDB0Made in ILPort 1 uses the GUID or MAC ID described on the label, for port 2 GUID or MAC add1 to port 1's description.1.4Safety WarningsFor safety warnings in French see “Avertissements de sécurité d’installation (Warnings in French)”on page 45. For safety warnings in German see “Sicherheitshinweise (Warnings in German)” onpage 46. For safety warnings in Spanish see “Advertencias de seguridad para la instalación (Warnings in Spanish)” on page 47.1. Installation InstructionsRead all installation instructions before connecting the equipment to the power source.2. Over-temperatureThis equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: 55 C (131 F).To guarantee proper air flow, allow at least 8cm (3 inches) of clearance around the ventilation openings.14Mellanox Technologies
ConnectX-2 Ethernet Card User ManualRev 1.63. During Lightning - Electrical HazardDuring periods of lightning activity, do not work on the equipment or connect or disconnect cables.4. Copper Cable Connecting/DisconnectingSome copper cables are heavy and not flexible, as such they should be carefullyattached to or detached from the connectors. Refer to the cable manufacturer for special warnings and instructions.5. Equipment InstallationThis equipment should be installed, replaced, or serviced only by trained and qualifiedpersonnel.6. Equipment DisposalDisposal of this equipment should be in accordance to all national laws and regulations.7. Local and National Electrical CodesThis equipment should be installed in compliance with local and national electricalcodes.Mellanox Technologies15
Rev 1.6Adapter Card Interfaces2Adapter Card Interfaces2.1I/O InterfacesEach card includes the following interfaces: SFP ports I/O panel LEDs I2C compatible connector (for debug)For dual port cards, port 1 connects to connector 1 of the device, while port 2 connects to connector 2 of the device.ConnectX-2 Ethernet Adapter Cards are compliant with the IEEE Std 802.3 Specification.Figure 3: Port NumberingPort 1Port 22.1.1 Ethernet SFP InterfaceThe ConnectX -2 device is compliant with the IEEE Std 802.3. The SFP port has one Tx/Rx pairof SerDes.Ethernet NIC cards listed in Table 3 on page 11 based on this device provide access tothe Ethernet ports by means of SFP connectors.2.1.2 PCI Express InterfaceThe ConnectX-2 adapter cards support PCI Express 2.0 (1.1 compatible) through an x8 edge connector. The device can be either a master initiating the PCI Express bus operations or a slaveresponding to PCI bus operations.16Mellanox Technologies
ConnectX-2 Ethernet Card User ManualRev 1.62.1.3 LED AssignmentThe board has I/O LEDs located on the I/O panel. The green LED, when lit, indicates that thedriver is running and a valid physical connection between nodes exists. If the green LED is blinking, it indicates a problem with the physical link. The yellow LED when lit, indicates a valid dataactivity link, this is the logical link. The yellow LED lights up when the network is discoveredover the physical link. A valid data activity link without data transfer is designated by a constantyellow LED indication. A valid data activity link with data transfer is designated by a blinking yellow LED indication. If the LEDs are not active, either the physical link or the logical link (or both)connections have not been established.Figure 4: LED - Port AssociationPort 1Port 2Figure 5: Physical and Logical Link IndicationsTable 5 - LEDsPort NumberLED NamePort 1Physical Link - GreenConstant on indicates a good physical linkBlinking indicates a problem with the PhysicallinkData Activity - YellowBlinking indicates Data TransferConstant on indicates no Data TransferPort 2Physical Link - GreenConstant on indicates a good physical linkBlinking indicates a problem with the PhysicallinkPort 1Port 2Data Activity - YellowBlinking indicates Data TransferConstant on indicates no Data TransferMellanox Technologies17
Rev 1.6Adapter Card InterfacesThe short bracket has the same port and LED footprint as the tall bracket.2.1.4 I2C Compatible InterfaceA three-pin header on the card is provided as the I2C compatible interface. SeeAppendix A,“Specifications,” on page 34 for the location on the board.Figure 6: I2C Connector2.2PowerAll adapter cards receive 12V and 3.3V power from the PCI Express Edge connector. All otherrequired power voltages are generated by on-board switch mode regulators. See “Specifications”on page 34.2.3MemoryThe adapter cards support multiple memory devices through the PCI Flash, and I2C.2.3.1 System MemoryThe card utilizes the PCI Express interface to store and access Ethernet fabric connection information and packet data on the system memory.2.3.2 FlashEach of the cards include one SPI Flash device accessible via the Flash interface oftheMT25408B0 ConnectX-2 EN device.There is a jumper on each adapter card that indicates to the device whether an on-board Flashdevice is to be used. Table 6 provides information on this jumper. See the schematic inAppendix A,“Specifications,” on page 34 for the jumper location.18Mellanox Technologies
ConnectX-2 Ethernet Card User ManualRev 1.6Table 6 - Jumper ConfigurationDescriptionFlash present/not presentCard DefaultConfigurationOptionconnection open – Flash presentconnection shorted – Flash not presentCommentsconnection open –Flash presentHeader 1x2Figure 7: Flash Jumper2.3.3 EEPROMEach board incorporates an EEPROM that is accessible through the I2C. The EEPROM is used forstoring the Vital Product Data (VPD). The EEPROM capacity is 4Kb.2.4VPD LayoutThe PCI VPD (Vital Product Data) layout, for each of the described Mellanox Technologies ConnectX -2 adapter cards complies with the format defined in the PCI 2.3 Specification, Appendix I.All ConnectX-2 adapter cards have the same PCI VPD layout.Table 7 - VPD Layout for MNPH29D-X[ST]ROffset (Decimal)ItemValue0Large Resource Type ID String Tag(0x02)0x821Length [7:0] LSB0xE2Length [15:8] MSB0x03DataHawk Dual Port17Large Resource Type VPD-R Tag(0x10)0x9018Length [7:0] LSB0x4F19Length [15:8] MSB0x0020VPD KeywordPN22Length0x15FormatDescriptionSTRSTRAdd in Card Part Number23PNPN%STR SPC44VPD KeywordECSTR46Length0x247RevisionRV%STRPCB revision49VPD KeywordSNSTRSerial Number51Length0x1852SerialNumber%STR SPC“00.00XXXX.XX”Engineering Change Level of the card(rev)Mellanox Technologies19
Rev 1.6Adapter Card InterfacesTable 7 - VPD Layout for MNPH29D-X[ST]ROffset (Decimal)ItemValueFormatDescription76VPD KeywordV0STRMisc Information78Length0x1079DataPCIe Gen2 x8STR SPC95VPD KeywordRVSTR97Length0x198Data0,9799Large Resource Type VPD-W Tag(0x11)0x91%CS0100Length [7:0] LSB0x99101Length [15:8] MSB0x00102VPD KeywordV1104Length0x6105DataN/ASTR SPC111VPD KeywordYASTR113Length0x20STREFI Driver versionAsset Tag114DataN/ASTR SPC“N/A”146VPD KeywordRWSTRRemaining read/write area148Length0x6A149DataSTR ZEROReserved (0x00)255Small Resource Type END Tag (0x11)0x78Table 8 - VPD Layout for MNPH29C-X[ST]R20Offset(Decimal)ItemValue0Large Resource Type ID String Tag (0x02)0x821Length [7:0] LSB0xE2Length [15:8] MSB0x03DataHawk Dual Port17Large Resource Type VPD-R Tag (0x10)0x9018Length [7:0] LSB0x4F19Length [15:8] MSB0x0020VPD KeywordPN22Length0x1523PNPN%STR SPC44VPD KeywordECSTREngineering Change Level ofthe card (rev)46Length0x247RevisionRV%STRPCB revision49VPD KeywordSNSTRSerial Number51Length0x1852SerialNumber%STR SPC“00.00XXXX.XX”Mellanox TechnologiesFormatDescriptionSTRSTRAdd in Card Part Number
ConnectX-2 Ethernet Card User ManualRev 1.6Table 8 - VPD Layout for ption76VPD KeywordV0STRMisc Information78Length0x1079DataPCIe Gen2 x8STR SPC95VPD KeywordRVSTR97Length0x198Data0,9799Large Resource Type VPD-W Tag (0x11)0x91%CS0100Length [7:0] LSB0x99101Length [15:8] MSB0x00102VPD KeywordV1104Length0x6105DataN/ASTR SPC111VPD KeywordYASTRAsset Tag113Length0x20114DataN/ASTR SPC“N/A”146VPD KeywordRWSTRRemaining read/write area148Length0x6A149DataSTR ZEROReserved (0x00)255Small Resource Type END Tag (0x11)STREFI Driver version0x78Mellanox Technologies21
Rev 1.6Driver Software and Firmware3Driver Software and Firmware3.1Driver Software3.1.1 LinuxFor Linux, download and install the latest MLNX EN driver software package available via theMellanox Web site at:http://www.mellanox.com Downloads Ethernet SW/Drivers. Follow the installation instructions included in the download package.3.1.2 WindowsFor Windows, download the MLNX EN – Ethernet driver. Download this package from the Mellanox Web site at:http://www.mellanox.com Downloads Et
2010 1.5 Minor formatting changes Nov. 22nd, 2010 1.4 Added Generation D card Mini Form Factor Oct. 28th, 2010 1.3 Added Technical Support and Firmware and Software Updates sections to the Pref-ace section Added RoCE Added ConnectX EN PXE Added Set up section, This is a sanity check after card installation. Added KCC statement to Appendix A
www.mellanox.com Mellanox Technologies ConnectX -4 Ethernet Single and Dual QSFP28 Port Adapter Card
Dual Port Cylinder Covers Can be used on all 1600 based dual port engines. This is the clean way to move on up to dual port cylinder heads. 1988 Dual Port Cylinder Covers - Black (set of 2) 1993 Dual Port Cylinder Covers - Chrome (set of 2) Deflector Plates Stock Factory Deflector Plates are used on all Type-1, 2 & 3 VW engines. They are .
Rev 1.0 Overview 8 Mellanox Technologies 1 Overview This document is a User’s Manual for Mellanox Technologies network VPI adapter cards based on the MT25408 ConnectX -2 VPI integrated circuit device.The cards described in this manual have the following main features: IBTA v1.2.1 compliant
Doosan Heavy Ind. DP World Cochin JNPT Port of Dubai Port of El Callao Port of Everglades Evergreen Fantuzzi-Reggiane Port of Felixstowe Fels crane FMC Technologies Port of Gioia Tauro Port of Gothenburg Port of Guanghzou Port of Hamburg Port of Heidland Port of Helsinki Port of Ho Ci Minh
NxM ("N by M") switch ! Often N M ! Goals " High throughput ! Best is MIN(sum of inputs, sum of outputs) " Avoid contention " Good scalability ! Linear size/cost growth Input Port Input Port Input Port Input Port Input Port Input Port Output Port Output Port Output Port Output Port Output Port Output Port Switch Fabric
Dell PowerEdge R630 Intel E5-2650 v4 2x12x2 2.2 10G Intel 82599ES (ixgbe) 10G Chelsio T520-CR (cxgbe) 10G Mellanox ConnectX-3 Pro (mlx4en) 10-50G Mellanox ConnectX-4 LX (mlx5en) HP ProLiant DL360p Gen8 Intel E5-2650 v2 8x2 2.6 10G Chelsio T540-CR (cxgbe) 10G Emulex OneConnect be3 (oce) SuperMicro 5018A-FTN4 Intel Atom C2758 8 2.4 10G Chelsio .
Port of Savannah Port of Jacksonville Port Everglades Port of Miami Port of Tampa Port of Mobile Port of Gulfport Port of New Orleans Port of South Louisiana Panama Canal Port Canaveral. New Orleans. Once 2014 rolls around, however, and the Panama . Canal opens to the post-Panamax ships, the definition of
--Russell, S. J., & Norvig, P. (2016). Artificial intelligence: a modern approach. Malaysia; Pearson Education Limited. Intelligence is the computational part of the ability to achieve goals in the world. It is related to the similar task of using computers to understand human intelligence, but AI does not have to confine itself to methods that are biologically observable.--By Prof. John .
