FBs-W2C

3y ago
146 Views
2 Downloads
1.19 MB
40 Pages
Last View : 1m ago
Last Download : 2m ago
Upload by : Bria Koontz
Transcription

FBs-W2C User ManualFBs-W2CWi-Fi Communication Module

FBs-W2C User ManualCategoryTable . 2Figure . 3Chapter1.FBs-W2C Wi-Fi Communication Module Product Introduction. 11.1Summary . 11.2Product Function List . 11.3Product Specification . 21.4Product Appearance . 31.5Installation . 41.6LINK LED Status . 4Chapter2.Wi-Fi Connection Setting . 52.1PLC Application Interface Wi-Fi Setting . 52.2Smart Config Wi-Fi Setting (SC) . 72.3FBs-W2C IP Searching . 82.4Wi-Fi RSSI . 9Chapter3.FATEK Standard Communication Service . 10Chapter4.Simple Network Time Protocol (SNTP). 11Chapter5.Firmware Upgrade (OTA) . 13Chapter6.FATEK Standard Searching Service . 146.1Window Layout . 146.2Functional Area and Properties . 156.2.1Scan. 156.2.2Device Found . 156.2.3Option . 166.2.4Properties . 176.3Work Area . 176.4Properties Window . 18Appendix APLC Register Configuration Table . 21I

FBs-W2C User ManualAppendix BTime Zone Table. 23Appendix CAccess Point Compatibility Table . 35TableTable 1: W2C Function List . 1Table 2: W2C Product Specification . 2Table 3: LINK LED Operation Mode . 4Table 4: PLC Register Config and Data Length Limitation . 5Table 5: IP Access Method . 8Table 6: Wi-Fi RSSI . 9Table 7: TCP/UDP Port PLC Register Config . 10Table 8: PLC Register Config Description . 12Table 9: SNTP Functions and PLC Register Configuration . 12Table 10: OTA Register Configuration Description . 13Table 11: W2C Configurator, Function Area and Properties introduction . 15Table 12: W2C Configurator Properties Window . 20II

FBs-W2C User ManualFigureFigure 1: FBs-W2C Front and Back Appearance . 3Figure 2: FBs-W2C Side Appearance . 3Figure 3: WinProladder ASCII Table . 5Figure 4: Build SSID ASCII table, edit table name and starting address . 6Figure 5: Enter SSID Data . 6Figure 6: IOS – Esptouch APP. 7Figure 7: Android – Esptouch APP . 7Figure 8: Esptouch operation interface, display W2C IP when connect successfully . 8Figure 9: Communication Service setting for WinProladder . 10Figure 10: W2C Configurator Window Layout . 14III

FBs-W2C User ManualModify RecordVersionDateNameV1.0.02019/1/24Curtis LiV1.0.12019/1/24Edison LinV1.0.22019/1/29Curtis LiV1.0.32019/1/29Ted HungV1.0.42019/2/13Curtis LiV1.0.52019/2/27Curtis LiV1.0.62019/5/20Curtis LiV1.0.72019/11/18Oscar WuIV

FBs-W2C User ManualChapter1. FBs-W2C Wi-Fi Communication ModuleProduct Introduction1.1 SummaryFBs-W2C is a Wi-Fi board plugged in the PLC, which enables wireless networktransmission capability. In addition, as a wireless communication module, itsupports Wi-Fi Station mode (STA mode) and needs to connect to router (AP). Inorder to make the W2C settings easier and more convenient, the Smart Configfunction is provided to allow users to easily connect to the router via the mobileapp. This module breaks the traditional PLC only through wired transmission,and the use is no longer subject to the physical network route. It can makemultiple PLCs establish connections through one AP at the same time. It issuperior to the traditional wired way in turns of maintenance.1.2 Product Function ListTable 1: W2C Function ListFunctionWi-Fi connectionDescriptionConnect with router, wireless networktransmission.Communicate with any of the FATEK standards andFATEK Standardcommunicate with devices that exist on the sameCommunication Servicelocal area network.SNTPFirmware UpdateFATEK Standard SearchServiceSupport SNTPFirmware update using OTA (via wireless network).Users can use the W2C Configurator (FATEKStandard Search Service CommunicationSoftware) to search for W2C and other FATEKdevices in the same local area network, checktheir operating status and set relatedconfiguration to control.1

FBs-W2C User Manual1.3 Product SpecificationFBs-W2C supports Wi-Fi protocol IEEE 802.11 b/g/n and with frequency 2.4 GHz 2.5GHz. Maximum TCP connections are up to 4.Table 2: W2C Product SpecificationCategoryItemCharacteristicWi-Fi protocol802.11 b/g/nFrequency Range2.4 GHz 2.5GHz (2400M 2483.5M)802.11 b: 20 dBmTransmit PowerWi-Fi802.11 g: 17 dBm802.11 n: 14 dBmReceivingSensitivity802.11 b: –91 dBm (11 Mbps)802.11 g: –75 dBm (54 Mbps)802.11 n: –72 dBm (MCS7)AntennaPCB on-board antennaCPUTensilica L106 32-bit processorOperating Voltage 2.5V 3.6VHardwareOperating Current Average current: 80 mARange of0 C 60 COperatingTemperatureSoftwareWi-Fi ModeStationSecurity ProtocolWPA/WPA2EncryptionWEP/TKIP/AESFirmware UpdateOTA (via Network)Network ProtocolIPv4, TCP/UDPMaximum TCPConnections42

FBs-W2C User Manual1.4 Product AppearanceFBs-W2C Wi-Fi communication board appearance shown as Figure 1 and Figure2, simply introduce as follow:① LINK LED: Located below the Link label, display the operational status ofW2C, such as connection, disconnection and firmware update, etc. Formore LED status information please refer to 1.6-LINK LED.② Mini Din Connector: Connector type of FBs-W2C Wi-Fi module, connectthrough port 0, with 4 pins and support RS232.Figure 1: FBs-W2C Front and Back AppearanceFigure 2: FBs-W2C Side Appearance3

FBs-W2C User Manual1.5 InstallationDirectly plugged FBs-W2C in port 0. It can automatically detect the baud rate.After the detection, it will set the port 0 baud rate as 115200 bps.1.6 LINK LED StatusLINK LED is in red, the LED will have different signal status depends on FBs-W2Ccurrently state. Table 3 shows the various signal status of LED.Table 3: LINK LED Operation ModeConnection StatusLINK LEDConnectingOn and off every 3 secsDisconnectedOffExecute Smart ConfigContinuous flashExecute OTATriple flash4

FBs-W2C User ManualChapter2. Wi-Fi Connection SettingBy installing the FBs-W2C Wi-Fi communication module, the PLC can connect tothe router for wireless network connection and transmission. Currently, thewireless network connection can be set in the following two ways: Setting through the PLC application interface. Setting through mobile App under Smart Config (SC) mode.2.1 PLC Application Interface Wi-Fi SettingAfter the connection is successful, the LINK LED will flash at 3s intervals (3seconds on, 3 seconds off). If you want to reconnect or connect other router,just write any value to R904, and the W2C will reconnect according to theinformation of the current register.Table 4: PLC Register Config and Data Length LimitationItemPLC register configData LengthLimitationSSIDR850 – R86832BytesPasswordR869 – R90364 BytesTrigger ConnectionR904Figure 3: WinProladder ASCII Table5

FBs-W2C User ManualFigure 4: Build SSID ASCII table, edit table name and starting addressThe starting address should match the following address:SSID: R850 R868Password: R869 R903Figure 5: Enter SSID Data6

FBs-W2C User Manual2.2 Smart Config Wi-Fi Setting (SC)For the convenience of use, the Smart Config connection method is alsoprovided. First you need to download the mobile app - Esptouch (support in iOS/ Android), as shown below. Esptouch sends the SSID and Password of therouter via UDP broadcast. W2C connects according to the information received.Figure 6: IOS – Esptouch APPFigure 7: Android – Esptouch APPTo put the W2C into the Smart Config mode, needs to switch the W2C rapidly3 times in succession.After the W2C is powered on, it must be powered off within three seconds.After repeating twice, the Smart Config mode will be enabled when the thirdpower is turned on.After entering the SC mode, W2C starts waiting for Esptouch broadcastinformation. At this time, the LED will flash continuously to indicate that the APPcan start transmitting, the longest waiting time is 60 seconds.If the connection fails after 60 seconds (such as wrong information, unstablenetwork quality), W2C will enter the PLC application interface mode andconnect through information stored in PLC before.7

FBs-W2C User ManualSince the Smart Config connection method is subject to the hardwarecompatibility, we provide Appendix C-Access Point Compatibility Table for usersto choose the appropriate mobile phone for connection settings.Figure 8: Esptouch operation interface, display W2C IP when connect successfully2.3 FBs-W2C IP SearchingAfter the FBs-W2C is connected to the AP, the W2C IP address can be viewed intwo ways (Table 5), and other devices can be connected to the PLC.Table 5: IP Access MethodItemDescriptionSmart ConfigDisplay on mobile APPFATEK StandardCommunication ServiceDisplay on FATEK standard communication servicesoftware (W2C Configurator)8

FBs-W2C User Manual2.4 Wi-Fi RSSIWi-Fi RSSI is an indicator for measuring the strength of the signal received by the device in wirelesscommunication. In order to monitor the connection quality of the W2C, the user can view it throughthe register R949 of the PLC. As shown inTable 6, the signal strength is shown. Expressed as a negative number, the unitis dBm, the value range is 0 -100, the closer to 0, the better the signal strength.Table 6: Wi-Fi RSSIPLC Register ConfigWi-Fi RSSISignal StrengthR949 -50Good-50 -70Normal-70 -90Bad -90No Signal9

FBs-W2C User ManualChapter3. FATEK Standard Communication ServicePLC has wireless network communication capability by plugging FBs-W2C Wi-Ficommunication module. It can communicate with objects such as WinProladderthat use FATEK standard communication in the same local area network.Supporting IPv4 and TCP/UDP protocols, can up to 4 TCP connections at thesame time. Default port of TCP/UDP are 500, it can be modified by PLC register,shown as Table 7.Table 7: TCP/UDP Port PLC Register ConfigLEDPLC register configTCP PortR946UDP PortR947In order to ensure the successful exchange of communication data in a wirelessenvironment, it is recommended to set the Time out and Retry as follow: Time out : 3 sec Retry : 5 timesWinProladder setting method can refer to Figure 9Figure 9: Communication Service setting for WinProladder10

FBs-W2C User ManualChapter4. Simple Network Time Protocol (SNTP)In addition to the above functions, the PLC with the FBs-W2C Wi-Ficommunication module can be used to perform network time correction via theNTP Server and support two synchronization modes according to different PLCregister value. Sync mode 1: Synchronize time back to PLC RTC.(For more details can refer PLC user manual 2 advanced applicationchapter15: RTC) Sync mode 2: Synchronize time back to specified PLC register.The user can flexibly select different mode according to individual needs. ThePLC register configuration of these two modes is shown in Table 8.In addition, W2C will automatically perform time correction with NTP Server atthe following timing, and update the time to the PLC registers.① When W2C is powered on, the time of W2C and time in corresponding PLCregisters according to the mode will be synchronized with NTP server.② Every 24 hours after powered on, the time of W2C and time incorresponding PLC registers according to the mode will be synchronizedwith NTP server.The W2C also provides the user to manually update the time to the PLC register.Simply set the value of the register R908 to 1, and the time will be updated tothe corresponding register according to the selected mode.In addition, if you want to change the time zone, you can refer to AppendixB-Time Zone Table. The time zone is the daylight time (if there is one in thearea), input the index value of the desired area into the register R910, and theninput 1 to the register to R908, the time will be updated.If the entered index value is exceeded or not in the Appendix B table, the systemdefault area is Taipei.If the SNTP server needs to be changed to another server, the new URL can bewritten to the register and enable the corresponding PLC register to notify W2Cthere’s a new setting needs to changed, default setting of SNTP server is ”pool.ntp.org”, W2C will synchronize time with SNTP server every 24 hours afterpowered on, the functions of SNTP and the configuration of the PLC register areshown inTable 9.11

FBs-W2C User ManualTable 8: PLC Register Config Description(Mode 1/Mode 2)DescriptionR4128/D3953(Second) 0-59R4129/D3954(Minute) 0-59R4130/D3955(Hour) 0-23R4131/D3956(Day) 1-31R4132/D3957(Month) 1-12R4133/D3958(Year) 0-99R4134/D3959(Week) 0-6Table 9: SNTP Functions and PLC Register ConfigurationPLC registerR907SNTP functionAfter setting the SNTP server URL, notify W2C to update theServer URL.R908Synchronize time back to PLC register immediately.R909Synchronize time back to PLC mode:1: mode 10: mode 2R910R911-R942Setting location indexFor example: Taipei area set to 86Setting SNTP server URLFor example: time.google.com12

FBs-W2C User ManualChapter5. Firmware Upgrade (OTA)OTA is a function to update the W2C firmware through the cloud. W2C willcheck the version information in the "w2c info" file on the cloud to determinewhether it needs to be updated. If a new version is found, the PLCcorresponding register will be set to 1, means users can update new firmwarefor the W2C.W2C will check the latest version on the cloud when it connects to AP and everymorning 00:01.When the user wants to update the firmware, W2C will check whether thecloud has a new version. If there is, the W2C will immediately update thefirmware of the OTA. If it is not found, it will go to the cloud to check the versioninformation again. The result will be checked. Decide whether to allow updates.When updating the firmware, LINK LED will flash three times per second thenoff one second, PLC register configuration description as Table 10.Table 10: OTA Register Configuration DescriptionPLC registerR905DescriptionResult for the version check of W2C0: No newer version1: Can update to newer versionR906After setting value 0, W2C will decide whether the updateis needed.13

FBs-W2C User ManualChapter6. FATEK Standard Searching ServiceW2C Configurator is a communication software provided by FATEK standardsearching service. Users can use this software to search for W2C devices in thesame local network to check their execution status and set related configurationif needed.6.1 Window LayoutFigure 10: W2C Configurator Window Layout14

FBs-W2C User Manual6.2 Functional Area and PropertiesThe functional area provides the user to scan the W2C devices in the same localarea network, also provides related settings. When press the properties button,the properties window will pop up to display more detailed information ofscanned device. Table 11 shows the functions in these areas, and more detailsare introduced in later sections.Table 11: W2C Configurator, Function Area and Properties introductionFunctionDescriptionScanSearching for the W2C devices in the same localnetwork.Device FoundOptionRecord the number of scanned devices.Includes Select Network, Scan Setting, Language andAbout for viewing the software version.PropertiesPress the button to display the scanned deviceproperties.6.2.1 ScanSearching for W2C devices in the same local network.6.2.2 Device FoundRecord the number of scanned W2C devices.15

FBs-W2C User Manual6.2.3 OptionProvide users to select scanning network, scan setting, language and W2Cconfigurator information.FunctionSelect NetworkDescriptionYou can select any network interface as the local networkto be scanned, and the IP address, MAC address, andsubnet mask of selected network interface are displayed inthe window.Scan SettingCan decease or increase the scanning time depends on thesituation, scan count can also be adjusted, default scantime is 5000ms and scan count is 1 time.16

FBs-W2C User ManualLanguageProvide English, Traditional Chinese and Simplified Chinesefor

FBs-W2C User Manual 10 Chapter3. FATEK Standard Communication Service PLC has wireless network communication capability by plugging FBs-W2C Wi-Fi communication module. It can communicate with objects such as WinProladder that use FATEK standard communication in the same local area network.

Related Documents:

Exo-FBS Exosome-depleted FBS Media Cat. # EXO-FBS-50A-1, EXO-FBS-250A-1, EXO-FBSHI-50A-1, EXO-FBSHI-250A-1 Exo-FBS Exosome –depleted FBS A. Overview Exosomes are 40-120 nm membrane vesicles secreted by most cell types in vivo and in vitro. Exosomes are found in blood, urine, amnioti

FBs-CMGSM User's Manual EN v3-07.doc Page #1 of 7 FBs-CMGSM USB COMMUNICATION GSM MODULE 1 1 FUNC RCV SND GSM ERR-IN OUT SIM 5 9 2 4 6 7 8 3 1 FBs-CMGSM, B1-CMGSM User’s Manual 1. Introduction FBs-CMGSM and B1-CMGSM (CMGSM for short) are communication modules for FATEK PLC systems FBs-xxMC and B1-xxM. CMGSM uses the GSM network to transfer .

where the Exo-FBS exosome-depleted FBS sample has a drastic reduction in exosome particles. Exo-FBS is depleted of bovine CD63 exosomes The tetraspanin CD63 protein is a common marker for exosomes. We utilized a bovine-specific anti-CD63 antibody to develop an Enzyme Linked Immunosorbent As

140903 FBs-CMGSM User's Manual EN v3-04 Page #1 of 7 FBs-CMGSM User's Manual 1. Introduction FBs-CMGSM (CMGSM for short) is communication module for FATEK PLC systems FBs-xxMC. CMGSM uses the GSM network to transfer the data.CMGSM is based on the quad band GSM module (850/900/1800/1900 MHz).CMGSM is backed up by Li-Ion accumulator.

FBs series PLC. Being an expansion board of Fatek PLC, there’s no extra space required to accommodate it. With this board, FBs-PLC can act as a client or a server over the Ethernet. Thus can serve the purpose of remote monitoring and diagnostic of PLC. While operating, it will utilize the port1 and port2 of CPU communication port. The working .

No. Judul Fakultas Judul . Ayu Niza Machfauzia M.Pd. FBS Strategi Guru Musik Dalam Pembelajaran Interpretasi Musik Romantik Di SMK N 2 Kasihan Bantul Yogyakarta Doktor 11 Dr. Kastam Syamsi M.Ed. FBS Model Perangkat Pembelajaran Membaca Dan Menulis Berdasarkan Pendekatan . 12 Margana M.Hum.,Ma FBS Blended Culture Sebagai Model Pembelajaran .

associated protein expression. METHODS Cell lines and treatment Human breast cancer cell lines MDA-MB-231 (DMEM 10% fetal bovine serum; FBS), HCC1143 (RPMI 10% FBS), and HCC1954 (RPMI 10% FBS) were obtained from American Type Culture Collection (ATCC). Murine mammary cancer cel

Plays are sometimes written from scratch; others are well known. KS3 Dramatic Society Club . of those students currently studying for ABRSM theory exams. Bring your lunch and have a chat. School Choir Large mixed (male and female voices) choir open to all years and abilities, which prepares for major musical events. Senior Jazz Combo Wild and unpredictable band of senior musicians in years .