KT715-KT745 Service Manual - Kohler Engines
KT715-KT745Service ManualIMPORTANT:Read all safety precautions and instructions carefully before operating equipment. Refer to operatinginstruction of equipment that this engine powers.Ensure engine is stopped and level before performing any maintenance or SpecificationsTools and AidsTroubleshootingAir Cleaner/IntakeFuel SystemGovernor SystemLubrication SystemElectrical SystemStarter SystemEmission Compliant SystemsDisassembly/Inspection and ServiceReassembly32 690 03 Rev. --1
SafetySAFETY PRECAUTIONSWARNING: A hazard that could result in death, serious injury, or substantial property damage.CAUTION: A hazard that could result in minor personal injury or property damage.NOTE: is used to notify people of important installation, operation, or maintenance information.WARNINGExplosive Fuel can causefires and severe burns.Do not fill fuel tank whileengine is hot or running.Gasoline is extremely flammableand its vapors can explode ifignited. Store gasoline only inapproved containers, in wellventilated, unoccupied buildings,away from sparks or flames.Spilled fuel could ignite if it comesin contact with hot parts or sparksfrom ignition. Never use gasolineas a cleaning agent.WARNINGRotating Parts can causesevere injury.Stay away while engineis in operation.Keep hands, feet, hair, andclothing away from all movingparts to prevent injury. Neveroperate engine with covers,shrouds, or guards removed.WARNINGCarbon Monoxide cancause severe nausea,fainting or death.Avoid inhaling exhaustfumes.Engine exhaust gases containpoisonous carbon monoxide.Carbon monoxide is odorless,colorless, and can cause death ifinhaled.2WARNINGCAUTIONAccidental Starts cancause severe injury ordeath.Disconnect and groundspark plug lead(s) beforeservicing.Electrical Shock cancause injury.Do not touch wires whileengine is running.Before working on engine orequipment, disable engine asfollows: 1) Disconnect spark pluglead(s). 2) Disconnect negative (–)battery cable from battery.Damaging Crankshaftand Flywheel can causepersonal injury.WARNINGHot Parts can causesevere burns.Do not touch enginewhile operating or justafter stopping.CAUTIONUsing improper procedures canlead to broken fragments. Brokenfragments could be thrown fromengine. Always observe and useprecautions and procedures wheninstalling flywheel.Never operate engine with heatshields or guards removed.WARNINGCleaning Solvents cancause severe injury ordeath.Use only in wellventilated areas awayfrom ignition sources.Carburetor cleaners and solventsare extremely flammable. Followcleaner manufacturer’s warningsand instructions on its proper andsafe use. Never use gasoline as acleaning agent.KohlerEngines.com32 690 03 Rev. --
MaintenanceMAINTENANCE INSTRUCTIONSWARNINGAccidental Starts can cause severe injury ordeath.Disconnect and ground spark plug lead(s)before servicing.Before working on engine or equipment, disable engine asfollows: 1) Disconnect spark plug lead(s). 2) Disconnectnegative (–) battery cable from battery.Normal maintenance, replacement or repair of emission control devices and systems may be performed by any repairestablishment or individual; however, warranty repairs must be performed by a Kohler authorized dealer.MAINTENANCE SCHEDULEEvery 25 Hours¹ Service/replace precleaner. Replace air cleaner element (if not equipped with precleaner).Air Cleaner/IntakeAir Cleaner/IntakeEvery 100 Hours¹ Replace air cleaner element (if equipped with precleaner). Change oil and filter. Remove cooling shrouds and clean cooling areas.Air Cleaner/IntakeLubrication SystemAir Cleaner/IntakeEvery 100 Hours Check that all fasteners are in place and components are properly secured. Replace fuel filter.Every 500 Hours² Have valve lash checked/adjusted.ReassemblyReassemblyEvery 500 Hours Replace spark plugs and set gap.¹ Perform these procedures more frequently under severe, dusty, dirty conditions.² Have a Kohler authorized dealer perform this service.Electrical SystemREPAIRS/SERVICE PARTSKohler genuine service parts can be purchased from Kohler authorized dealers. To find a local Kohler authorizeddealer visit KohlerEngines.com or call 1-800-544-2444 (U.S. and Canada).32 690 03 Rev. --KohlerEngines.com3
MaintenanceOIL RECOMMENDATIONSWe recommend use of Kohler oils for best performance.Other high-quality detergent oils (including synthetic)of API (American Petroleum Institute) service class SJor higher are acceptable. Select viscosity based onair temperature at time of operation as shown in tablebelow.10W-30SAE 305W-30 F -20 C -300-2020-10324005010806020STORAGEIf engine will be out of service for 2 months or morefollow procedure below.1. Add Kohler PRO Series fuel treatment or equivalentto fuel tank. Run engine 2-3 minutes to get stabilizedfuel into fuel system (failures due to untreated fuelare not warrantable).2. Change oil while engine is still warm from operation.Remove spark plug(s) and pour about 1 oz. ofengine oil into cylinder(s). Replace spark plug(s) andcrank engine slowly to distribute oil.3. Disconnect negative (–) battery cable.4. Store engine in a clean, dry place.1003040FUEL RECOMMENDATIONSWARNINGExplosive Fuel can cause fires and severeburns.Do not fill fuel tank while engine is hot orrunning.Gasoline is extremely flammable and its vapors canexplode if ignited. Store gasoline only in approvedcontainers, in well ventilated, unoccupied buildings,away from sparks or flames. Spilled fuel could igniteif it comes in contact with hot parts or sparks fromignition. Never use gasoline as a cleaning agent.NOTE: E15, E20 and E85 are NOT approved andshould NOT be used; effects of old, stale orcontaminated fuel are not warrantable.Fuel must meet these requirements: Clean, fresh, unleaded gasoline. Octane rating of 87 (R M)/2 or higher. Research Octane Number (RON) 90 octane minimum. Gasoline up to 10% ethyl alcohol, 90% unleaded isacceptable. Methyl Tertiary Butyl Ether (MTBE) and unleadedgasoline blend (max 15% MTBE by volume) areapproved. Do not add oil to gasoline. Do not overfill fuel tank. Do not use gasoline older than 30 days.4KohlerEngines.com32 690 03 Rev. --
SpecificationsEngine DimensionsDimensions in millimeters.Inch equivalents shown in [ ].32 690 03 Rev. --KohlerEngines.com5
SpecificationsENGINE IDENTIFICATION NUMBERSKohler engine identification numbers (model, specification and serial) should be referenced for efficient repair,ordering correct parts, and engine replacement.Model . . . . . . . . . . . . . . . . . . . . . KT7157000 Series EngineNumerical DesignationSpecification . . . . . . . . . . . . . . . KT715-0001Serial . . . . . . . . . . . . . . . . . . . . . 4323500328Year Manufactured CodeCodeYear432013442014452015GENERAL SPECIFICATIONS3,6BoreKT715StrokeFactory CodeKT725725 cc (44 cu. in.)Oil Capacity (refill)Maximum Angle of Operation (@ full oil level)4KT74569 mm(2.72 in.)747 cc(46 cu. in.)67 mm (2.64 in.)DisplacementTORQUE SPECIFICATIONS3,5KT730 KT735 KT74083 mm (3.27 in.)1.9 l (2.0 qt.)25 KT715Baffle and Sheet Metal into AluminumM5 Thread Forming FastenersKT725KT730KT735KT740KT7458.5 N·m (75 in. lb.) into new hole4.0 N·m (35 in. lb.) into used hole10.7 N·m (95 in. lb.) into new hole7.3 N·m (65 in. lb.) into used holeM6 Thread Forming FastenersBlower Housing and Sheet MetalM3 HI-LO ScrewM4 HI-LO ScrewM5 Fasteners2.3 N·m (20 in. lb.)2.8 N·m (25 in. lb.)6.2 N·m (55 in. lb.) into new hole4.0 N·m (35 in. lb.) into used hole10.7 N·m (95 in. lb.) into new hole7.3 N·m (65 in. lb.) into used holeM6 FastenersCarburetorMounting Nut6.2-7.3 N·m (55-65 in. lb.)Connecting RodCap Fastener (torque in increments)11.3 N·m (100 in. lb.)3Values are in Metric units. Values in parentheses are English equivalents.Exceeding maximum angle of operation may cause engine damage from insufficient lubrication.5Lubricate threads with engine oil prior to assembly.6Any and all horsepower (hp) references by Kohler are Certified Power Ratings and per SAE J1940 & J1995 hpstandards. Details on Certified Power Ratings can be found at KohlerEngines.com.46KohlerEngines.com32 690 03 Rev. --
SpecificationsTORQUE SPECIFICATIONS3,5KT715CrankcaseBreather AssemblyOuter Cover StudKT725KT730KT735KT7406.2 N·m (55 in. lb.) into new hole4.0 N·m (35 in. lb.) into used holeOuter Cover Hex NutOil Drain Plug1.3 N·m (11.5 in. lb.)13.6 N·m (10 ft. lb.)Cylinder HeadHead Bolt Fastener (torque in 2 increments)Rocker Arm Studfirst to 22.6 N·m (200 in. lb.)finally to 41.8 N·m (370 in. lb.)11.3 N·m (100 in. lb.)FlywheelRetaining Screw74.5 N·m (55 ft. lb.)Fuel PumpScrew2.8 N·m (25 in. lb.)GovernorLever Nut6.8 N·m (60 in. lb.)IgnitionSpark PlugModule FastenerRectifier-Regulator Fastener27 N·m (20 ft. lb.)4.0-6.2 N·m (35-55 in. lb.)4.0 N·m (35 in. lb.)Intake ManifoldMounting Fastener (torque in 2 increments)first to 7.4 N·m (66 in. lb.)finally to 9.9 N·m (88 in. lb.)MufflerM8 Hex Nuts5/16-18 CapscrewBracket Screw24.4 N·m (216 in. lb.)16.9 N·m (150 in. lb.)9.9 N·m (88 in. lb.)Oil PanFastener24.4 N·m (216 in. lb.)Oil PumpScrew (no torque sequence)9.9 N·m (88 in. lb.)Oil Sentry Pressure Switch4.5 N·m (40 in. lb.)Solenoid (Starter)Mounting HardwareNut, Positive ( ) Brush Lead4.0-6.0 N·m (35-53 in. lb.)8.0-11.0 N·m (71-97 in. lb.)Speed Control BracketFastener35KT74510.7 N·m (95 in. lb.) into new holes7.3 N·m (65 in. lb.) into used holesValues are in Metric units. Values in parentheses are English equivalents.Lubricate threads with engine oil prior to assembly.32 690 03 Rev. --KohlerEngines.com7
SpecificationsTORQUE SPECIFICATIONS3,5KT715KT725Starter AssemblyThru BoltInertia DriveSolenoid ShiftMounting ScrewBrush Holder Mounting ScrewKT730KT7358.8 N·m (78 in. lb.)Valve CoverFastener9.6 N·m (85 in. lb.)CLEARANCE SPECIFICATIONS3KT715CamshaftEnd PlayRunning ClearanceBore I.D.NewMax. Wear LimitBearing Surface O.D.NewMax. Wear LimitKT725KT730KT735KT740KT7450.06/0.40 mm (0.0024/0.0157 in.)0.040/0.077 mm (0.0016/0.0030 in.)20.000/20.025 mm (0.7874/0.7884 in.)20.038 mm (0.7889 in.)19.948/19.960 mm (0.7854/0.7858 in.)19.945 mm (0.7852 in.)Connecting RodConnecting Rod-to-Crankpin Running ClearanceNewMax. Wear LimitConnecting Rod-to-Crankpin Side ClearanceConnecting Rod-to-Piston Pin Running ClearancePiston Pin End I.D.NewMax. Wear LimitCrankcaseGovernor Cross Shaft Bore I.D.NewMax. Wear Limit5KT7454.5-5.7 N·m (40-50 in. lb.)5.6-9.0 N·m (49-79 in. lb.)23.8 N·m (211 in. lb.)2.5-3.3 N·m (22-29 in. lb.)StatorMounting Screw3KT7400.037/0.083 mm (0.0015/0.0033 in.)0.098 mm (0.0039 in.)0.261/0.67 mm (0.0102/0.0264 in.)0.013/0.032 mm (0.0005/0.0013 in.)17.013/17.027 mm (0.6698/0.6704 in.)17.040 mm (0.6709 in.)8.025/8.075 mm (0.3159/0.3179 in.)8.088 mm (0.3184 in.)Values are in Metric units. Values in parentheses are English equivalents.Lubricate threads with engine oil prior to assembly.8KohlerEngines.com32 690 03 Rev. --
SpecificationsCLEARANCE SPECIFICATIONS3KT715CrankshaftEnd Play (free)Bore (in crankcase)NewMax. Wear LimitBore (in oil pan)NewCrankshaft Bore (in oil pan)-to-Crankshaft Running ClearanceNewFlywheel End Main Bearing JournalO.D. - NewO.D. - Max. Wear LimitMax. TaperMax. Out-of-RoundOil Pan End Main Bearing JournalO.D. - NewO.D. - Max. Wear LimitMax. TaperMax. Out-of-RoundConnecting Rod JournalO.D. - NewO.D. - Max. Wear LimitMax. TaperMax. Out-of-RoundT.I.R.PTO End, Crank in EngineEntire Crank, in V-BlocksCylinder BoreBore I.D.NewMax. Wear LimitMax. Out-of-RoundMax. TaperKT725KT735KT740KT7450.075/0.595 mm (0.0030/0.0023 in.)40.974/40.987 mm (1.6131/1.6137 in.)41.000 mm (1.6142 in.)40.974/41.000 mm (1.6457/1.6142 in.)0.039/0.087 mm (0.0015/0.0034 in.)40.913/40.935 mm (1.6107/1.6116 in.)40.840 mm (1.608 in.)0.022 mm (0.0009 in.)0.025 mm (0.0010 in.)40.913/40.935 mm (1.6107/1.6116 in.)40.840 mm (1.608 in.)0.022 mm (0.0009 in.)0.025 mm (0.0010 in.)35.950/35.974 mm (1.4154/1.4163 in.)35.950 mm (1.4154 in.)0.018 mm (0.0007 in.)0.025 mm (0.0010 in.)0.279 mm (0.0110 in.)0.200 mm (0.0079 in.)83.006/83.031 mm (3.2679/3.2689 in.)83.069 mm (3.2704 in.)0.120 mm (0.0047 in.)0.050 mm (0.0020 in.)Cylinder HeadMax. Out-of-Flatness0.076 mm (0.003 in.)GovernorGovernor Cross Shaft-to-Crankcase Running ClearanceCross Shaft O.D.NewMax. Wear LimitGovernor Gear Shaft-to-Governor Running ClearanceGear Shaft O.D.NewMax. Wear LimitIgnitionSpark Plug GapModule Air Gap3KT7300.025/0.126 mm (0.0009/0.0049 in.)7.949/8.000 mm (0.3129/0.3149 in.)7.936 mm (0.3124 in.)0.050/0.210 mm (0.0020/0.0083 in.)5.990/6.000 mm (0.2358/0.2362 in.)5.977 mm (0.2353 in.)0.76 mm (0.030 in.)0.203/0.305 mm (0.008/0.012 in.)Values are in Metric units. Values in parentheses are English equivalents.32 690 03 Rev. --KohlerEngines.com9
SpecificationsCLEARANCE SPECIFICATIONS3KT715Piston, Piston Rings, and Piston PinPiston-to-Piston Pin Running ClearancePin Bore I.D.NewMax. Wear LimitPin O.D.NewMax. Wear LimitTop Compression Ring-to-Groove Side ClearanceMiddle Compression Ring-to-Groove Side ClearanceOil Control Ring-to-Groove Side ClearanceTop Compression Ring End GapNew BoreUsed Bore (Max.)Middle Compression Ring End GapNew BoreUsed Bore (Max.)Thrust Face O.D.7NewMax. Wear LimitPiston Thrust Face-to-Cylinder Bore7 Running ClearanceNewValves and Valve TappetsClearanceValve Tappet to Crankcase Running ClearanceIntake Valve Stem-to-Valve Guide Running ClearanceExhaust Valve Stem-to-Valve Guide Running ClearanceIntake Valve Guide I.D.NewMax. Wear LimitExhaust Valve Guide I.D.NewMax. Wear LimitValve Guide Reamer SizeStandard0.25 mm O.S.Intake Valve Minimum LiftExhaust Valve Minimum LiftNominal Valve Face Angle37KT725KT730KT735KT740KT7450.006/0.017 mm (0.0002/0.0007 in.)17.006/17.012 mm (0.6695/0.6698 in.)17.025 mm (0.6703 in.)16.995/17.000 mm (0.6691/0.6693 in.)16.994 mm (0.6691 in.)0.030/0.070 mm (0.001/0.0026 in.)0.030/0.070 mm (0.001/0.0026 in.)0.060/0.190 mm (0.0022/0.0073 in.)0.189/0.277 mm (0.0074/0.0109 in.)0.531 mm (0.0209 in.)1.519/1.797 mm (0.0598/0.0708 in.)2.051 mm (0.0808 in.)82.978 mm (3.2668 in.)82.833 mm (3.2611 in.)0.019/0.062 mm (0.0007/0.0024 in.)0.127/0.178 mm (0.0050/0.0070 in.)0.013/0.073 mm (0.0005/0.0029 in.)0.040/0.0780 mm (0.0016/0.0031 in.)0.052/0.090 mm (0.0020/0.0035 in.)7.040/7.060 mm (0.2772/0.2780 in.)7.140 mm (0.2811 in.)7.040/7.060 mm (0.2772/0.2780 in.)7.160 mm (0.2819 in.)7.050 mm (0.2776 in.)7.300 mm (0.2874 in.)8.500 mm (0.3346 in.)8.500 mm (0.3346 in.)45 Values are in Metric units. Values in parentheses are English equivalents.Measure 6 mm (0.2362 in.) above bottom of piston skirt at right angles to piston pin.10KohlerEngines.com32 690 03 Rev. --
SpecificationsGENERAL TORQUE VALUESEnglish Fastener Torque Recommendations for Standard ApplicationsBolts, Screws, Nuts and Fasteners Assembled Into Cast Iron or SteelGrade 2 or 5 FastenersInto AluminumSizeGrade 2Tightening Torque: N·m (in. lb.) 20%8-322.3 (20)10-243.6 (32)10-323.6 (32)1/4-207.9 (70)1/4-289.6 (85)5/16-1817.0 (150)5/16-2418.7 (165)3/8-1629.4 (260)3/8-2433.9 (300)Grade 5Grade 82.8 (25)4.5 (40)4.5 (40)13.0 (115)15.8 (140)28.3 (250)30.5 (270)—————18.7 (165)22.6 (200)39.6 (350)———2.3 (20)3.6 (32)—7.9 (70)—17.0 (150)———Tightening Torque: N·m (ft. lb.) 20%5/16-24—3/8-16—3/8-24—7/16-1447.5 (35)7/16-2061.0 (45)1/2-1367.8 (50)1/2-2094.9 (70)9/16-12101.7 (75)9/16-18135.6 (100)5/8-11149.5 (110)5/8-18189.8 (140)3/4-10199.3 (147)3/4-16271.2 (200)—47.5 (35)54.2 (40)74.6 (55)101.7 (75)108.5 (80)142.4 (105)169.5 (125)223.7 (165)244.1 (180)311.9 (230)332.2 (245)440.7 (325)40.7 (30)67.8 (50)81.4 (60)108.5 (80)142.5 (105)155.9 (115)223.7 (165)237.3 (175)311.9 (230)352.6 (260)447.5 (330)474.6 (350)637.3 (470)—————————————Metric Fastener Torque Recommendations for Standard ApplicationsProperty ClassSize4.85.8NoncriticalFastenersInto Aluminum8.810.912.9Tightening Torque: N·m (in. lb.) 10%M41.2 (11)1.7 (15)M52.5 (22)3.2 (28)M64.3 (38)5.7 (50)M810.5 (93)13.6 (120)2.9 (26)5.8 (51)9.9 (88)24.4 (216)4.1 (36)8.1 (72)14.0 (124)33.9 (300)5.0 (44)9.7 (86)16.5 (146)40.7 (360)2.0 (18)4.0 (35)6.8 (60)17.0 (150)Tightening Torque: N·m (ft. lb.) 10%M1021.7 (16)27.1 (20)M1236.6 (27)47.5 (35)M1458.3 (43)76.4 (56)47.5 (35)82.7 (61)131.5 (97)66.4 (49)116.6 (86)184.4 (136)81.4 (60)139.7 (103)219.7 (162)33.9 (25)61.0 (45)94.9 (70)Torque ConversionsN·m in. lb. x 0.113in. lb. N·m x 8.85N·m ft. lb. x 1.356ft. lb. N·m x 0.73732 690 03 Rev. --KohlerEngines.com11
Tools and AidsCertain quality tools are designed to help you perform specific disassembly, repair, and reassembly procedures. Byusing these tools, you can properly service engines easier, faster, and safer! In addition, you’ll increase your servicecapabilities and customer satisfaction by decreasing engine downtime.Here is a list of tools and their source.SEPARATE TOOL SUPPLIERSKohler ToolsContact your local Kohler source ofsupply.SE Tools415 Howard St.Lapeer, MI 48446Phone 810-664-2981Toll Free 800-664-2981Fax 810-664-8181Design Technology Inc.768 Burr Oak DriveWestmont, IL 60559Phone 630-920-1300Fax 630-920-0011TOOLSDescriptionAlcohol Content TesterFor testing alcohol content (%) in reformulated/oxygenated fuels.Camshaft Endplay PlateFor checking camshaft endplay.Camshaft Seal Protector (Aegis)For protecting seal during camshaft installation.Cylinder Leakdown TesterFor checking combustion retention and if cylinder, piston, rings, or valves are worn.Individual component available:Adapter 12 mm x 14 mm (Required for leakdown test on XT-6 engines)Dealer Tool Kit (Domestic)Complete kit of Kohler required tools.Components of 25 761 39-SIgnition System TesterCylinder Leakdown TesterOil Pressure Test KitRectifier-Regulator Tester (120 V AC/60Hz)Dealer Tool Kit (International)Complete kit of Kohler required tools.Components of 25 761 42-SIgnition System TesterCylinder Leakdown TesterOil Pressure Test KitRectifier-Regulator Tester (240 V AC/50Hz)Digital Vacuum/Pressure TesterFor checking crankcase vacuum.Individual component available:Rubber Adapter PlugElectronic Fuel Injection (EFI) Diagnostic SoftwareFor Laptop or Desktop PC.EFI Service KitFor troubleshooting and setting up an EFI engine.Components of 24 761 01-SFuel Pressure TesterNoid Light90 AdapterIn-line "T" FittingCode Plug, Red WireCode Plug, Blue WireSchrader Valve Adapter HoseFlywheel Holding Tool (CS)For holding flywheel of CS series engines.Flywheel PullerFor properly removing flywheel from engine.Flywheel Strap WrenchFor holding flywheel during removal.12KohlerEngines.comSource/Part No.Kohler 25 455 11-SSE Tools KLR-82405SE Tools KLR-82417Kohler 25 761 05-SDesign Technology Inc.DTI-731-03Kohler 25 761 39-SKohler 25 455 01-SKohler 25 761 05-SKohler 25 761 06-SKohler 25 761 20-SKohler 25 761 42-SKohler 25 455 01-SKohler 25 761 05-SKohler 25 761 06-SKohler 25 761 41-SDesign Technology Inc.DTI-721-01Design Technology Inc.DTI-721-10Kohler 25 761 23-SKohler 24 761 01-SDesign Technology 037SE Tools KLR-82407SE Tools KLR-82408SE Tools KLR-8240932 690 03 Rev. --
Tools and AidsTOOLSDescriptionHydraulic Valve Lifter ToolFor removing and installing hydraulic lifters.Ignition System TesterFor testing output on all systems, including CD.Inductive Tachometer (Digital)For checking operating speed (RPM) of an engine.Offset Wrench (K and M Series)For removing and reinstalling cylinder barrel retaining nuts.Oil Pressure Test KitFor testing/verifying oil pressure on pressure lubricated engines.Radiator TesterFor pressure testing radiator and cap on Aegis liquid-cooled engines.Rectifier-Regulator Tester (120 volt current)Rectifier-Regulator Tester (240 volt current)For testing rectifier-regulators.Components of 25 761 20-S and 25 761 41-SCS-PRO Regulator Test HarnessSpecial Regulator Test Harness with DiodeSpark Advance Module (SAM) TesterFor testing SAM (ASAM and DSAM) on engines with SMART-SPARK .Starter Servicing Kit (All Starters)For removing and reinstalling drive retaining rings and brushes.Individual component available:Starter Brush Holding Tool (Solenoid Shift)Triad/OHC Timing Too
Service Manual KT715-KT745 2 Safety 3 Maintenance 5 Specifi cations 12 Tools and Aids . ² Have a Kohler authorized dealer perform this service. REPAIRS/SERVICE PARTS Kohler genuine service parts can be purchased from Kohler authorized dealers. To fi nd a local Kohler authorized . Year Manufactured Code Factory Code Code Year 43 2013 44 .
ezo3008g 8 3000 155 800,000 25 kohler belt ezo3010g 10 3000 130 1,000,000 belt38 kohler ezo3708g 8 3700 130 800,000 belt38 kohler ezo5005g 5 5000 130 500,000 25 kohler belt ezo6004g 4 6000 160 400,000 25 kohler belt ezo6006g 6 6000 145 belt600,000 38 kohler ezo7004g 4 7000 belt160 400,000 25 kohler
Kohler Stock Coil Kohler Stock Coil Wire Kohler 10, 12, 14 hp Stock Head Gasket MSD Coil Wire Kit 12.00 60.00 22.00 10.00 18.50 Kohler Bowl Kohler Bowl Gasket Hardened Kohler Points Pin K&N Air Filter 7" OD x 9" L (4" opening) Re-cast Kohler Head with Holes (10, 12, 14 & 16 hp) 11.00 3.00 12.00 62.00 145.00 Heavy Duty Main Engine .
and pulling straight up out of the . Flush Valve A 1 Release flush valve by turning righ and pull straight up on the canister. 1 2 1 2. Kohler Co. 9 1102602-A2- I. 1102602-A2-I Kohler Co. Kohler Co. 1102602-A2- I. 1102602-A2-I CALL US FOR HELP NEW ZEALAND AUSTRALIA KOHLER NZ LTD KOHLER CO. Free Ph: 0800 564 537 (0800 KOHLER) Free Ph: 1 800 .
Owner's Manual IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating instruction of equipment that this engine powers. Ensure engine is stopped and level before performing any maintenance or service. Warranty coverage as outlined in the warranty card and on KohlerEngines.com.
ONLY KOHLER ENGINES MAKES KOHLER GENUINE PARTS. KOHLER genuine parts are the key to keeping every hardworking KOHLER engine in top shape. They’re built for the long haul and designed to give peace of mind. Keep this guide handy, and use it whenever you need to find a part . EFI ECH630-ECH749, ECV630-ECV749 PART NUMBER 24 083 03-S .
KOHLER Command PRO V-Twins Model Specifications For more information, contact your KOHLER source of supply, or call toll-free in the U.S. and Canada 800-544-2444. Kohler Co., Kohler, Wisconsin 53044 Tel 920-457-4441 Fax 920-459-1570
Repairs/Service Parts We recommend that you use a Kohler authorized dealer for all maintenance, service, and engine parts. To fi nd a Kohler authorized dealer visit KohlerEngines.com or call 1-800-544-2444 (U.S. and Canada). Storage If engine will be out of service for 2 months or more follow procedure below. 1. Add Kohler PRO Series fuel .
realizes a functional behavior of a logic system from a given description (stated in form of verbal statements, truth table, K-map, state diagram, etc.) Example : Synthesize a logic function that realizes the following truth table. Use AND, OR, and NOT gates Figure 2.15. A function to be synthesized. Chapter 2-14 Synthesis of digital circuits f (a) Canonical sum-of-products f (b) Minimal-cost .
