Assembly Instructions CAR SEAT ADAPTOR
Assembly InstructionsCAR SEAT ADAPTORFor City Select / City Versa www.babyjogger.comThis Car Seat Adaptor is designed to be used with the seat mountingbrackets on your Baby Jogger City Select or City Versa stroller. Thiscar seat adaptor is only compatible with these stroller models.NOTE: Before you start, please refer to the Table of Contents on page 2 to ensureyou follow the proper instructions for your car seat.This Kit Includes:2 Adaptor Brackets1 U-Shaped Bar (A)1 U-Shaped Bar (B)1 Spring Support Bar (C)1 Graco Support Bar (D)U-Shaped Bar (A)U-Shaped Bar (B)Spring Support Bar (C)Graco Support Bar (D)Adaptor Brackets8575 Magellan Parkway, Suite 1000 Richmond, VA 23227 T: 800-241-1848 F: 804-262-6277 www.babyjogger.com
Table of Contents3Graco Snugride4Peg Perego Primo Viaggio5Chicco Keyfit6Baby Trend Flex LocEvenflo DiscoveryEvenflo EmbraceEvenflo NurtureEvenflo SecureRideSafety 1st On Board7Cybex AtonMaxi Cosi8Other Available AccessoriesFor the most up to date information on our list of compatible car seats, please visit the FAQ sectionof our website or call Baby Jogger customer service at 800-241-1848.Car seat models or brands sold internationally are not always confirmed to be compatible withBaby Jogger’s car seat adaptors. If you need assistance determining the compatibility of your internationalcar seat, please visit our website to locate the distributor nearest you.2
GracoUses the 2 Adaptor Brackets, U-shaped bar (A), U-shaped bar (B),Spring support bar (C), and Graco support bar (D)The car seat adaptor comes fully assembled for use with Graco model car seats. Should you detach the spring support bar (C)or Graco support bar (D) and need to reassemble, please see “Support Bar Configuration” below for instructions.Car Seat Adaptor Installation:CLICK1 Insert Adaptor Brackets into thecorresponding mounting brackets on yourstroller. The Adaptor Brackets are securewhen they click into place.2 Open the compressionlocks on the AdaptorBrackets by flippingthe red latches up.NOTE: The right and left mountingbrackets on your stroller aredetermined by standing in front ofand facing the stroller.3 Insert the U-shaped bar (A) into the openings on the frontof the adaptor brackets. The A bar should be inserted allthe way so that the stoppers hit the plastic adaptor brackets.4 Close the compression locks on the adaptorbrackets by flipping the red latches down,locking the U-shaped bar (A) in place.CLICKCLICKGreen IndicatorStopper5 From the rear of the stroller, connect the second U-shaped bar (B)over the ends of the already installed U-shaped bar (A) until itclicks into place. You will see only green in the indicator on top ofthe bars when the U-shaped bars are locked in place.6 Place car seat on the car seat adaptor andpress down firmly until it clicks into place.Fasten and properly tighten the AdaptorBracket Safety Belt over the car seat beforeoperation.Support Bar Configuration:CLICK1 Squeeze spring support bar (C)and insert into holes on the inside ofU-shapped support bar (B).2 Align the openings of the Graco support bar (D) with the endsof U-shaped support bar (B). Slide The Graco support bar onto theU-shaped bar (B) and snap onto spring support bar (C). You willhear it click when properly attached.3
Peg-PeregoUses the 2 Adaptor Brackets, U-shaped bar (A),U-shaped bar (B), and the Spring support bar (C)Support Bar Configuration:The car seat adaptor comes fully assembled for use with Graco model car seats. The Graco support bar (D) must beremoved prior to attaching your Peg-Perego car seat to the Baby Jogger Car Seat Adaptor.1 Holding the U-shaped bar (B), unsnap Graco support bar (D)from the Spring support bar (C) and remove.Car Seat Adaptor Installation:CLICK1 Insert Adaptor Brackets into thecorresponding mounting brackets on yourstroller. The Adaptor Brackets are securewhen they click into place.2 Open the compressionlocks on the AdaptorBrackets by flippingthe red latches up.NOTE: The right and left mountingbrackets on your stroller aredetermined by standing in front ofand facing the stroller.4 Close the compression locks on the adaptorbrackets by flipping the red latches down,locking the U-shaped bar (A) in place.3 Insert the U-shaped bar (A) into the openings on the frontof the adaptor brackets. The A bar should be inserted allthe way so that the stoppers hit the plastic adaptor brackets.CLICKCLICKGreen IndicatorStopper5 From the rear of the stroller, connect the second U-shaped bar (B)over the ends of the already installed U-shaped bar (A) until itclicks into place. You will see only green in the indicator on top ofthe bars when the U-shaped bars are locked in place.46 Place car seat on the car seat adaptor andpress down firmly until it clicks into place.Fasten and properly tighten the AdaptorBracket Safety Belt over the car seat beforeoperation.
ChiccoUses the 2 Adaptor Brackets, U-shaped bar (A), and the U-shaped bar (B)Support Bar Configuration:The car seat adaptor comes fully assembled for use with Graco model car seats. The Graco support bar (D) and springsupport bar (C) must be removed prior to attaching your Chicco car seat to the Baby Jogger Car Seat Adaptor.1 Holding the U-shaped bar (B), unsnap Graco support bar (D)from the Spring support bar (C) and remove.2 Squeeze spring support bar (C) andremove from U-shaped support bar (B).Car Seat Adaptor Installation:CLICK1 Insert Adaptor Brackets into thecorresponding mounting brackets on yourstroller. The Adaptor Brackets are securewhen they click into place.2 Open the compressionlocks on the AdaptorBrackets by flippingthe red latches up.NOTE: The right and left mountingbrackets on your stroller aredetermined by standing in front ofand facing the stroller.4 Close the compression locks on the adaptorbrackets by flipping the red latches down,locking the U-shaped bar (A) in place.3 Insert the U-shaped bar (A) into the openings on the frontof the adaptor brackets. The A bar should be inserted allthe way so that the stoppers hit the plastic adaptor brackets.CLICKCLICKGreen IndicatorStopper5 From the rear of the stroller, connect the second U-shaped bar (B)over the ends of the already installed U-shaped bar (A) until itclicks into place. You will see only green in the indicator on top ofthe bars when the U-shaped bars are locked in place.6 Place car seat on the car seat adaptor andpress down firmly until it clicks into place.Fasten and properly tighten the AdaptorBracket Safety Belt over the car seat beforeoperation.5
Baby Trend, Evenflo, Safety 1stUses the 2 Adaptor Brackets, U-shaped bar (A), and the U-shaped bar (B)Support Bar Configuration:The car seat adaptor comes fully assembled for use with Graco model car seats. The Graco support bar (D) and springsupport bar (C) must be removed prior to attaching your car seat to the Baby Jogger Car Seat Adaptor.1 Holding the U-shaped bar (B), unsnap Graco support bar (D)from the Spring support bar (C) and remove.2 Squeeze spring support bar (C) andremove from U-shaped support bar (B).Car Seat Adaptor Installation:CLICK1 Insert Adaptor Brackets into thecorresponding mounting brackets on yourstroller. The Adaptor Brackets are securewhen they click into place.2 Open the compressionlocks on the AdaptorBrackets by flippingthe red latches up.NOTE: The right and left mountingbrackets on your stroller aredetermined by standing in front ofand facing the stroller.4 Close the compression locks on the adaptorbrackets by flipping the red latches down,locking the U-shaped bar (A) in place.3 Insert the U-shaped bar (A) into the openings on the frontof the adaptor brackets. The A bar should be inserted allthe way so that the stoppers hit the plastic adaptor brackets.CLICKCLICKGreen IndicatorStopper5 From the rear of the stroller, connect the second U-shaped bar (B)over the ends of the already installed U-shaped bar (A) until itclicks into place. You will see only green in the indicator on top ofthe bars when the U-shaped bars are locked in place.66 Place car seat on the car seat adaptor. Fasten andproperly tighten the Adaptor Bracket Safety Beltover the car seat before operation.
Cybex & Maxi CosiUses the 2 Adaptor BracketsCar Seat Adaptor Installation:CLICK1 Insert Adaptor Brackets into thecorresponding mounting brackets on yourstroller. The Adaptor Brackets are securewhen they click into place.NOTE: The right and left mountingbrackets on your stroller aredetermined by standing in front ofand facing the stroller.2 Close the compression locks on the adaptorbrackets by flipping the red latches down.CLICK3 Place car seat on the car seatadaptor and press downfirmly until it clicks into place.Fasten and properly tightenthe Adaptor Bracket SafetyBelt over the car seat beforeoperation.7
Other Available AccessoriesSecond Seat KitAllows you to convert your single City Selectstroller into a double. This kit comes with thecomplete second seat and the second seatmounting brackets.Rain Canopy - BassinetCompletely encloses the top and sides of theCity Select Bassinet while providing ventilation ininclement weather. Made from BPA and PVC Freematerial.Bassinet KitAllows you to convert your City Select seatinto a Bassinet. The Bassinet Kit contains plushfabric and support brackets that convert theCity Select’s single seat into a Bassinet in a fewsimple steps.Carry BagProtects your stroller during transport or storage.Child TrayFeatures a cup holder and easy to clean surface.Glider BoardAttaches to rear axle of any single or doubleBaby Jogger stroller to allow your toddler to ridealong. Holds up to 45 lbs.Belly BarProvides child with a soft padded area to hold onto when the stroller is in use.Rain Canopy - SeatCompletely encloses the front and sides of theCity Select seat while providing ventilation ininclement weather. Made from BPA and PVC Freematerial.Rain Canopy - BasketNylon covering designed to protect the contentsof the City Select basket from inclement weather.8Universal Parent ConsoleFeatures a cup holder and additional storagecompartments.Foot MuffFor children 6-18 mo. Keeps legs & feet warm ininclement weather.Plush Stroller Hand MuffKeeps your hands warm and dry while pushingyour stroller. Features a soft and plush interiorand weatherproof exterior.Cooler BagDesigned to help keep food or drinks cold.Holds six 12 oz. cans.8575 Magellan Parkway, Suite 1000 Richmond, VA 23227 T: 800-241-1848 F: 804-262-6277 www.babyjogger.com
The car seat adaptor comes fully assembled for use with Graco model car seats. The Graco support bar (D) must be removed prior to attaching your Peg-Perego car seat to the Baby Jogger Car Seat Adaptor. 1 . Holding the U-shaped bar (B), unsnap Graco support bar (D) from the Spring support bar (C) and remove. Car Seat Adaptor Installation: CLICK .
your Infant Car Seat, as described in the instruction manual provided by the Infant Car Seat manufacturer. † WHEN USING ONLY ONE INFANT CAR SEAT ADAPTER OR TWO FOR TWINS, THE FOLLOWING INFANT CAR SEATS CAN BE USED: † If your Infant Car Seat is not one of the models listed above, DO NOT use your infant car seat with this car seat adapter.
Title: Coverking Seat Covers Installation Instructions Author: CARID Subject: Coverking Seat Covers Installation Instructions Keywords "seat covers, custom seat covers, car seat covers, waterproof seat covers, car seat protectors"
NOTE If replacing a Slimline assembly with a DISH assembly, remove the four bolts from the adaptor plate, and remove the adaptor plate. NOTE If replacing a Slimline assembly with a DISH assembly, align the small post on the back of the DISH 1000 adaptor plate with the small groove on the skew assembly hub. Fit the small post into the groove. Secure
Remove the infant car seat/carrier by reversing the above steps. See your infant car seat manufacturer's instructions for proper release lever operation. REMOVING THE INFANT SEAT/CARRIER 3. Bring the infant seat attachment straps through the seat belt guides in the infant car seat/carrier and fas-ten the buckle. To loosen, tilt the buckle and .
3. Secure sloped ceiling adaptor to housing with (2) 8-32 screws as supplied. 4. Install fixture/adaptor assembly into ceiling structure ensuring adaptor is positioned appropriately to the pitch of the ceiling. 5. For dry ceiling applications only, remove sloped ceiling adaptor prior to installation of plasterboard. A.
18 SETTING UP YOUR BIKE 19 SETTING UP YOUR BIKE CONTINUED SEAT HEIGHT SEAT DEPTH ySet the seat height level with the top of your hip bone. y Loosen the knob to adjust the seat height. y Tighten the knob to lock the seat in place. ySet the seat elbow-to-fingertips length from the handlebars. yOpen the latch to adjust the seat depth. y Close the latch to lock the seat in place.
UNIGRAPHICS(NX)-6 Seat UNIGRAPHICS(NX) VIEWER-2 Seat UNIGRAPHICS(NX) CAM-1 Seat MOULD FLOW-1 Seat POWER MILL-4 Seat POWER SHAPE-2 Seat CAMI SOFTWARE-1 Seat AUTO CAD-4 Seat CAP-1Seat WORK STATION FOR DESIGN/MFA-15 PC WORK STATION FOR PROGRAMMING-4 PC Ensures the
and Materials, ASTM; and by the Society of Automotive Engineers, SAE. These groups are summarized as follows: 100 Series (C10000) Coppers This group comprises the pure coppers, those with a designated mini-mum copper content of 99.3%, for high electrical conductivity. Also included within this group are the high copper alloys, those with
