12V SUBMERSIBLE WATER PUMP
WHAT’S IN THE BOX12V SUBMERSIBLEWATER PUMP6,750 L/H FLOWINSTRUCTION MANUALSPECIFICATIONSVoltage:12V DCRated Input Power:84 WattCurrent:9AmpMax. Flow Rate: 6,750 litres/hourMax. Head:5 metersSize of Outlet:ø29mmPower Cord:5mWeight:1.4kgsozito.com.au12V Submersible PumpAuxiliary Cable - 2.1mCord with On/OffSwitch & 12V DC PlugSBP- 012
KNOW YOUR PRODUCTSUBMERSIBLE PUMP1. Pump Housing4. Discharge Outlet2. Power Cord5. Strainer3. Strainer TabsSETUP & PREPARATION1. INSTALLATION GUIDE Pump is suitable for use with fresh and salt water applications.The pump can be used for portable or permanent applicationsPortable Applications1. Prior to immersing the pump in waterdetermine the depth of water for thelength of hose required.1Note: Calculate overall hose length topump to the desired location22. Attach a ø29mm hose (ø25mm min.hose recommended) (not supplied) tothe discharge outlet and fasten with astainless steel clamp (not supplied). Itis recommended that you use a goodquality hose that will not kink whenmaking sharp bends.3453 Determine the desired location for thepump. It is best located where the wateris potentially deepest, ie., at the lowestpossible level of the area to be drainedAUXILIARY CABLE6.12V DC Plug7.On/Off Switch8.Power Cord Connector4. Ensure that the hose is positioned ina way that runs level or continuouslyupward. This will eliminate the chance ofair pockets developing.Note: Restricting the flow from the pump byusing a smaller hose does not damage thepump however, it will reduce the flow.678ONLINE MANUALScan this QR Code with yourmobile device to take you tothe online manual.
2. WIRINGWiringPermanent Applications1. Determine the desired location and position for the pump. Refer“Portable Applications”.2. Remove the strainer from thebottom of the pump by depressingthe strainer tabs, on both sides ofthe pump. T he submersible pump comessupplied with an auxiliarycable. The 12V DC plug onthe auxiliary cable enablesthe pump to be powered froma standard 12V power outletfound in cars, boats and somegenerators. T he power cord of thesubmersible pump also comeswith power cord connectors onboth the pump cord and theauxiliary cable. This enablesthe wires to be connectedquickly and accurately with lesschance of a need for strippingor cutting. If attaching the strainer towood, fasten with stainlesssteel screws. If attaching the strainer tometal or fibreglass, firstmount a wooden block tothe surface, and then fastenthe strainer to the woodenblock.3. Mount the pump on the strainer sothat both lock tabs snap into place.(the pump may be reversed on thesetabs if so desired).4. Attach hose. Refer “Portable Applications”CAUTION: THE STRAINER MUST ALWAYS BEPROPERLY INSTALLED BEFORE ATTACHING ANDRUNNING PUMP. T he auxiliary cable has a ON/OFF switch which can beused to manually control thesubmersible pump.IMPORTANT!: ENSURE THAT ALL ELECTRICAL WIRINGIS SECURED IN PLACE WITH THE CONNECTIONS WELLABOVE THE POTENTIAL WATER LEVEL.
SUBERSIBLEPUMPFLOATSWITCHMOLDEDCONNECTORSIN LINESWITCH12V DCPLUGMOLDEDCONNECTORS3. TROUBLE SHOOTINGThe two wiring diagrams below show how to set up the submersiblepump without a float switch (manual operation) and with a floatswitch (automatic operation).Wiring for Manual OperationThe manual system is the simplest system but it only provides ONOFF control of the pump. Consequently, pumps are often left ONlonger than necessary.SymptomPossibleCauseCurePump notworkingBlown fuseReplace fuse in 12V DC PlugReducedFlowBlocked strainerClean outside of strainer and cleandebris from around impeller.Discharge linecloggedClean out hose by back flushing.Low batteryvoltageCheck battery condition and charge ifnecessary.Kinkeddischarge hoseChange to a hose that does not kink atthe bends.WireconnectionsMake sure wire connections are notcorroded. Check to be sure no wire joinsare hanging down into the water.Float switchfailure. (ifconnected).Lift end of float switch up - if pump runs,switch is OK. If pump does not run, turnmanual switch to on position - if pumpruns, automatic switch has failed.Somethingunder the float(if connected)Clean under the float to make suredebris is not holding the float up.Stuck float (ifconnected).Check to see that the float is loosemoves freely. If float action appearssluggish and/or the float does notmove freely, intermittent or sporadicoperation of the pump may occur. Thiscondition is usually the result of oil and/or dirt accumulating in and around themovable parts of the switch. To correct,clean the switch, checking for smoothand free operation of the float. Repeat ifnecessaryIMPORTANT.Switch mountedtoo lowIf the pump is sucking air and theautomatic switch has not reached theOFF position, then the switch may bemounted too low for the pump andshould be reinstalled at least 6mm higherthan the pump base.12VSUBERSIBLEPUMPIN LINESWITCH12V DCPLUGMOLDEDCONNECTORSWiring forAutomatic OperationFor automatic operation,a float switch (available fromspecialized outlets) can beinstalled. A float switch detectsthe rising level of water andturns on the submersiblepump. The pump then pumpsthe water out until its levelhas been substantially reduced, at which point the pump is switchedoff again. The automatic system assures that the area is alwayspumped out, even when unattended. It extends the life of the pumpand your battery.The automatic system also provides for manual control of the pump,as it includes an ON/OFF SIN LINESWITCHNo waterpumpedPump won’tshut off.12V DCPLUGMOLDEDCONNECTORSNote: When not using the supplied auxiliary cable (ie. when settingup a fixed installation), it is recommended that you use a 10 Ampfuse and a 12V/10 Amp power supply.12VSUBERSIBLEPUMPSBP-012
MAINTENANCE4. MAINTENANCE & STORAGEMaintenanceRegularly check the pump to be sure that the filter base and impellerare not clogged with debris. To clean, push in the tabs and lift up thepump housing.DESCRIPTION OF SYMBOLSDCDirect currentmAL/HLitres per hourIPMilliamperesElectrical EmissionsComfomity (EMC)Note. The discharge hose need not be removed.StorageThe pump itself is not affected by freezing temperatures .However, if the pump is embedded in ice or surrounded by ice,it cannot be used. Never turn the pump on if it is embedded in orsurrounded by iceIMPORTANT! BEFORE CLEANING YOUR SUBMERSIBLEPUMP OR CARRYING OUT ANY MAINTENANCEPROCEDURE, MAKE SURE THAT THE UNIT IS OFF ANDTHE PUMP IS DISCONNECTED FROM THE POWERSUPPLY TO PREVENT ACCIDENTAL STARTING.CARING FOR THE ENVIRONMENTPumps that are no longer usable should not be disposed of withhousehold waste but in an environmentally friendly way. Pleaserecycle where facilities exist. Check with your local council authorityfor recycling advice.Recycling packaging reduces the need for landfill and raw materials.Reuse of recycled material decreases pollution in the environment.Please recycle packaging where facilities exist. Check with yourlocal council authority for recycling advice.SPARE PARTSStrainerAuxiliary CableSPSBP012-13SPSBP012-14Spare parts can be ordered from the Special Orders Deskat your local Bunnings Warehouse.For further information, or any parts not listed here, visitwww.ozito.com.au or contact Ozito Customer Service:Australia 1800 069 486New Zealand 0508 069 486E-mail: enquires@ozito.com.au
Tool:Model No.SPARE PARTS41235689117131012The following is a list of spare parts carried by Ozito.Please contact Customer Service for any parts notlisted.ItemNo.1314DescriptionStrainerAuxiliary CablePart No.SPSBP012-13SPSBP012-14ItemNo.DescriptionPart No.How To OrderAvailable spare parts can be ordered through the Special Orders Desk at any Bunnings Warehouse. If you have anyfurther questions, please contact Ozito Customer Service on:Australia: 1800 069 486New Zealand: 0508 069 486enquiries@ozito.com.au
GENERAL PUMP SAFETY WARNINGSRead the whole manual carefully and make sure you know how to switch the tool offin an emergency, before operating the tool.Save these instructions and other documents supplied with this tool for futurereference.WARNING! Read all safety warnings and all instructions. Failure to followthe warnings and instructions may result in electric shock, fire and/or seriousinjury.Save these instructions1. Work areaa. Keep work area clean and well lit. Cluttered or dark areas invite accidents.b. Do not operate pumps in explosive atmospheres, such as in the presenceof flammable liquids, gases or dust. Pumps create sparks which may ignite thedust or fumes.c. Keep children and bystanders away while operating a pump. Distractions cancause you to lose control.2. Electrical safety When using 12 Volt equipment, basic safety precautions, including thefollowing, should always be followed to reduce risk of fire, electric shock,personal injury and material damage.a. Do not abuse the cord. Never use the cord for carrying, pulling orunplugging the pump. Keep cord away from heat, oil, sharp edges ormoving parts. Damaged or entangled cords increase the risk of electric shock.b. The electric motor has been designed for 12V only. Always check that thepower supply corresponds to the voltage on the rating plate.b. Avoid accidental starting. Ensure the switch is in the off position beforeplugging in. Carrying pumps with your finger on the switch or plugging in pumpsthat have the switch on invites accidents.c. Remove any adjusting key or wrench before turning the pump on. A wrenchor a key left attached to a rotating part of the pump may result in personal injury.d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,clothing and gloves away from moving parts. Loose clothes, jewellery or longhair can be caught in moving parts.4. Pump use and carea. Disconnect the plug from the power source before making any adjustments,changing accessories, or storing pumps. Such preventive safety measuresreduce the risk of starting the pump accidentally.b. Maintain pumps. Check for misalignment or binding of moving parts,breakage of parts and any other condition that may affect the pumpsoperation. If damaged, have the pump repaired before use. Many accidentsare caused by poorly maintained pumps.c. Use the pump, accessories and tool bits etc., in accordance with theseinstructions and in the manner intended for the particular type ofpump,taking into account the working conditions and the work to beperformed. Use of the pump for operations different from intended could result ina hazardous situation.5. Servicea. Have your pump serviced by a qualified repair person using only identicalreplacement parts. This will ensure that the safety of the pump is maintained.3. Personal safetya. Stay alert, watch what you are doing and use common sense whenoperating a pump. Do not use a pump while you are tired or under theinfluence of drugs,alcohol or medication. A moment of inattention whileoperating pumps may result in serious personal injury.SUBMERSIBLE PUMP SAFETY WARNINGSCAUTION: Not intended for cleaning and other maintenance of swimming pools.WARNING! This product is intended for pumping water in a home domesticapplication.Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluidsother than water will damage the submersible pump and/or create a fire hazard.WARNING! This product is not suitable for use with drinking (potable) water.This appliance is not intended for use by persons (including children) withreduced physical, sensory or mental capabilities, or lack of experience andknowledge, unless they have been given supervision or instruction concerninguse of the appliance by a person responsible for their safety.Children should be supervised to ensure that they don’t play with the appliance. Ensure the submersible pump is disconnected from mains power when installing Do not install or operate the submersible pump in an explosive environment ornear flammable material. Do not operate the submersible pump without liquid. Do not run the submersible pump dry.WARNING! The submersible pump together with associated pipework operateunder pressure. Do not disconnect submersible pump or pipework until internal pressure hasbean released. Failure to do this could result in personal injury and damage toproperty. Avoid inserting hands into the inlets/outlets of the submersible pump while it isconnected to mains power. Before using the submersible pump, always inspect it visually. Do not use thepump if it is cracked and/or damaged. If the submersible pump is damaged,contact customer service.Never work or perform maintenance on the pump without first making sure it has beendisconnected from the mains power.Pollution of the liquid could occur due to leakage of lubricants.IMPORTANT Avoid inserting hands into the mouth of the pump if it is connected to themains. The electrical connections must always be made in a dry area. Make sure thatelectrical connections are protected from inundations. Protect the plug and the powercable from heat, oil or sharp edges. If damaged, the power cable must be replaced bya qualified electrician.
WARRANTYIN ORDER TO MAKE A CLAIM UNDER THISWARRANTY YOU MUST RETURN THE PRODUCTTO YOUR NEAREST BUNNINGS WAREHOUSE WITHYOUR BUNNINGS REGISTER RECEIPT. PRIOR TORETURNING YOUR PRODUCT FOR WARRANTYPLEASE TELEPHONE OUR CUSTOMER SERVICEHELPLINE:Australia 1800 069 486New Zealand 0508 069 486TO ENSURE A SPEEDY RESPONSE PLEASEHAVE THE MODEL NUMBER AND DATE OFPURCHASE AVAILABLE. A CUSTOMER SERVICEREPRESENTATIVE WILL TAKE YOUR CALLAND ANSWER ANY QUESTIONS YOU MAYHAVE RELATING TO THE WARRANTY POLICYOR PROCEDURE.The benefits provided under this warranty are in additionto other rights and remedies which are available to you at law.Our goods come with guarantees that cannot be excludedat law. You are entitled to a replacement or refund for a major failure andfor compensation for any other reasonably foreseeable loss or damage.You are also entitled to have the goods repairedor replaced if the goods fail to be of acceptable quality and the failuredoes not amount to a major failure.Generally you will be responsible for all costs associated witha claim under this warranty, however, where you have sufferedany additional direct loss as a result of a defective product youmay be able to claim such expenses by contacting our customer servicehelpline above.3 YEAR REPLACEMENT WARRANTYYour product is guaranteed for a period of 36 months fromthe original date of purchase. If a product is defective it willbe replaced in accordance with the terms of this warranty.Warranty excludes consumable parts, for example: o-rings, bearings,seals, gaskets, drain caps, and all accessories.WARNINGThe following actions will result in the warranty being void. I f the pump has been operated on a supply voltage otherthan that specified on the tool. If the pump shows signs of damage or defects causedby or resulting from abuse, accidents or alterations. Failure to perform maintenance as set out within the instructionmanual. If the pump is disassembled or tampered with in any way.Professional, industrial or high frequency use.OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.1113
The two wiring diagrams below show how to set up the submersible pump without a float switch (manual operation) and with a float switch (automatic operation). Wiring for Manual Operation The manual system is the simplest system but it only provides ON-OFF control of the pump. Consequently, pumps are often left ON longer than necessary. Wiring for
3042f012 dpa pump 3042f022 dpa pump 3042f050 dpa pump 3042f052 dpa pump 3042f062 dpa pump 3042f080 dpa pump 3042f101 dpa pump 3042f102 dpa pump 12 volt 3042f110 dpa pump 3042f150 dpa pump 3042f152 dpa pump 3042f152-r dpa pump 3042f170 dpa pump 3042f171 dpa pump 3042f172 dpa pump 3042f210 dpa pump 3042f212 dpa pump 3042f213 dpa pump 3042f213-r .
Paxton Net2 plus. 3 V 0 802.3at - 12V DC 0V 0V 0V 0V N.C. N.O 2 COM N.C. N.O COM Data/D0 Clock/D1 CAT5 RS485 0V 10 T R 100 Data/D0 Clock/D1 10/100 Ethernet N.C. N.O COM 12V - 24V 12V 1 2 12V LED LED LED 12V LED LED LED LED EIT 12V DC 12V DC I 1 Paxton Net2 plus 12V 7Ah V 2 1 0 V 2 1 04 2 U
gas price. changer. quick start guide. w a r r a n t y. better business bureau. wiring connection diagram. power cable child parent controller box. figure 1. dc 12v in data in dc 12v in data in dc 12v in data in dc 12v in data in dc 12v out data out dc 12v out data out dc 12v out data ou
Net2 plus 12V DC I 1 Paxton 0V 0V 0V N.C. N.O 2 COM N.C. N.O COM Data/D0 Clock/D1 CAT5 RS485 0V 10 TX RX 100 Data/D0 Clock/D1 10/100 Ethernet N.C. N.O COM 12V - 24V 12V 1 2 12V LED LED LED 12V LED LED LED LED EXIT 12V DC 12V DC I 1 Paxton Net2 plus 337-727 337-773 2A 2A 0 C -
The submersible pump unit comprises a submersible pump assembly directly-coupled to a submersible electric motor. The connecting bracket accommodates the coupling between the pump and motor shafts and also serves as the water intake passage. The pump unit is suspended in the well by the riser pipe, and the electric power is taken down from the well
Pump Description N3306, N3400 A submersible pump for efficient pumping of clean water, surface water, and wastewater containing solids or long-fibered material. The pump is designed for sustained high efficiency. N3231, N3312, N3356, N3531, N3800 A submersible pump for efficient pumping of clean water, surface water, and
RTE-P12-24V RTE-P1AF20 100 - 240V AC 8 Pin RTE-P11-AC120V RTE-P12-AC120V RTE-P1D12 12V DC 8 Pin RTE-P11-12V RTE-P12-12V RTE-P2AD24 24V AC/DC 11 Pin RTE-P21-24V RTE-P22-24V RTE-P2AF20 100 - 240V AC 11 Pin RTE-P21-AC120V RTE-P22-AC120V RTE-P2D12 12V DC 11 Pin RTE-P21-12V RTE-P22-12V Part Number
Isolated 12V DC/DC Converter Vi Vi-Vo Vo-The Texas Instruments DCP021212 is an isolated 12V to 12V DC-DC converter. It takes a 12V input, referenced to a common ground, and outputs 12V referenced to some other voltage. It uses AC and magnetic coupling to isolate the output from the input. This is used to supply 12V referenced to
