Sees S-3 Ry-Type Sprinkles 11.2K Orizontal Sidewall .
Worldwidewww.tyco-fire.comContactsSeries DS-3 Dry-Type Sprinklers11.2K Horizontal SidewallStandard Response, Extended CoverageGeneralDescriptionTYCO Series DS-3 Dry-Type Sprinklers,11.2K Horizontal Sidewall, StandardResponse, Extended Coverage, Ordinary Hazard (ECOH) are decorativeglass bulb automatic sprinklers. Theyare intended for use in applicationswhere the sprinklers and/or a portion ofthe connecting piping may be exposedto freezing temperatures; for example,horizontal piping extensions through awall to protect an unheated area of abuilding.to do so may impair the performanceof these devices.The owner is responsible for maintaining their fire protection systemand devices in proper operating condition. Contact the installing contractor or product manufacturer with anyquestions.Series DS-3 Dry-Type Sprinklers mustonly be installed in fittings that meetthe requirements of the Design Criteriasection. Installation of Series DS-3 DryType Sprinklers in a recessed installation will void all sprinkler warranties, aswell as void the sprinkler’s laboratoryApprovals.Series DS-3 Extended CoverageOrdinary Hazard Horizontal Sidewall,Dry-Type Sprinklers are designed forextended coverage use in ordinaryhazard occupancies (ECOH) per NFPA13.SprinklerIdentificationNumber (SIN)Series DS-3 Dry-Type Sprinklersprovide protection of coverage areasup to 16 ft x 20 ft (320 ft2) as comparedto standard coverage horizontal sidewall sprinklers having a maximum coverage area of 10 ft x 10 ft (100 ft2) forordinary hazard occupancies.TY5339NOTICESeries DS-3 Dry-Type Sprinklersdescribed herein must be installedand maintained in compliance with thisdocument, as well as with the applicable standards of the NATIONAL FIREPROTECTION ASSOCIATION (NFPA),in addition to the standards of any otherauthorities having jurisdiction. FailureRefer to Table A and the Design CriteriasectionIMPORTANTRefer to Technical Data SheetTFP2300 for warnings pertaining toregulatory and health information.Always refer to Technical DataSheet TFP700 for the “INSTALLERWARNING” that provides cautionswith respect to handling and installation of sprinkler systems and components. Improper handling andinstallation can permanently damagea sprinkler system or its components and cause the sprinkler to failto operate in a fire situation or causeit to operate prematurely.Page 1 of 8TechnicalDataApprovalsUL and C-UL ListedMaximum Working Pressure175 psi (12,1 bar)Inlet Thread Connections1 Inch NPTISO 7-R 1Discharge CoefficientRefer to Table BTemperature Ratings155 F (68 C) and 200 F (93 C)FinishesSprinkler: Refer to Table EEscutcheon: Refer to Table EAUGUST 2018Physical CharacteristicsInlet CopperPlug CopperYoke. . . . . . . . . . . . . . . . . . . . . . . . Stainless SteelCasing. . . . . . . . . . . . . . Galvanized Carbon SteelInsert BronzeBulb Seat BronzeBulb. . . . . . . . . . . . . . . . . . . . . . . . . Glass (3 mm)Compression Screw BronzeDeflector BronzeFrame BronzeGuide Tube Stainless SteelWater Tube Stainless SteelSpring. . . . . . . . . . . . . . . . . . . . . . Stainless SteelSealing Assembly. . Beryllium Nickel w/TEFLONPin. . . . . . . . . . . . . . . . . . . . . . . . . Stainless SteelButton Spring Stainless SteelHelper Spring Stainless SteelEscutcheon Carbon SteelOperationWhen TYCO Series DS-3 Dry-TypeSprinklers, 11.2K Horizontal Sidewall,Standard Response, Extended Coverage, Ordinary Hazard (ECOH) are inservice, water is prevented from entering the assembly by the Plug withSealing Assembly (Ref. Figure 1) in theInlet of the sprinkler.The glass bulb contains a fluid thatexpands when exposed to heat. Whenthe rated temperature is reached, thefluid expands sufficiently to shatterthe glass bulb, and the Bulb Seat isreleased.The compressed Spring is then ableto expand and push the Water Tube aswell as the Guide Tube outward. Thisaction simultaneously pulls inward onthe Yoke, withdrawing the Plug withSealing Assembly from the Inlet allowing the sprinkler to activate and flowwater.TFP550
TFP550Page 2 of 8PLUG WITHGASKETEDSPRING SEALPLATEINLETYOKE1" FIGURE 1SERIES DS-3 HORIZONTAL SIDEWALL DRY-TYPE SPRINKLER TY5339 (ECOH)ASSEMBLYTemperatureRatingBulbColor Code155 F (68 C)Red200 F (93 C)GreenSPRINKLER FINISHNaturalBrassChromePlatedWhitePolyester1, 2Notes:1. Listed by Underwriters Laboratories, Inc. (maximum order length of 48 inches)2. Listed by Underwriters Laboratories for use in Canada (maximum order length of 48 inches).TABLE ASERIES DS-3 HORIZONTAL SIDEWALL DRY-TYPE SPRINKLERSEXTENDED COVERAGE, ORDINARY HAZARD (TY5339)LABORATORY LISTINGS AND APPROVALSDesignCriteriaSprinkler FittingsInstall 1 inch NPT Series DS-3 Dry-TypeSprinklers in the 1 inch NPT outlet orrun of the following fittings:The TYCO Series DS-3 Dry-Type Sprinklers, 11.2K Horizontal Sidewall, Standard Response, Extended Coverage,Ordinary Hazard (ECOH) are for use inordinary hazard occupancies with noncombustible unobstructed constructionand with a ceiling slope not exceeding 2 inches per foot (9.2 ), using thedesign criteria provided in Table C, aswell as any additional requirementsspecified in NFPA 13 for Extended Coverage Sidewall Spray Sprinklers. malleable or ductile iron threadedtee fittings that meet the dimensional requirements of ANSI B16.3(Class 150)A 36 in. (914 mm) clearance must bemaintained between the top of thesprinkler deflector and any miscellaneous storage.The unused outlet of the threaded tee isplugged as shown in Figure 6.Series DS-3 Dry-Type Sprinklers maybe installed on sloped ceilings inloading docks with a maximum roofslope of 4 inches per foot (18.4 ) asshown in Figure 8 and using the designcriteria provided in Table C. cast iron threaded tee fittings thatmeet the dimensional requirementsof ANSI B16.4 (Class 125)Do not install Series DS-3 Dry-TypeSprinklers into elbow fittings. The Inletof the sprinkler can contact the interiorof the elbow.Series DS-3 Dry-Type Sprinklers canalso be installed in the 1 inch NPT outletof a GRINNELL Figure 730 MechanicalTee. However, the use of the Figure 730Tee for this arrangement is limited towet pipe r½)2-1/2 to 14-3/4(63 mm to 375 mm)11.2(161,3)15 to 18-3/4(381 mm to 476 mm)10.9(157,0)19 to 23(483 mm to 584 mm)10.8(155,5)23-1/4 to 26-3/4(591 mm to 679 mm)10.7(154,1)27-1/4 to 31-1/4(692 mm to 794 mm)10.6(152,6)31-1/2 to 35-1/4(800 mm to 895 mm)10.5(151,2)35-1/2 to 39-1/2(902 mm to 1003 mm)10.4(149,8)39-3/4 to 43-1/2(1010 mm to 1105 mm)10.3(148,3)43-3/4 to 48(111 mm to 1219 mm)10.2(146,9)Notes: K-factor Length is determined as follows: Flush: Order Length from Figure 2 plus 1/2 in.(12,7 mm) Deep: Order Length from Figure 4 plus 3-1/4 in.(82,6 mm) Without Escutcheon: Order Length from Figure 5minus 2-1/4 in. (57,2 mm)TABLE BDISCHARGE COEFFICIENTS
TFP550Page 3 of 8ApplicationSeries DS-3 (TY5339)Horizontal SidewallDry-Type Sprinkler (ECOH)OH Group 1 (0.15 gpm/sq.ft)Standard ResponseSeries DS-3 (TY5339)Horizontal SidewallDry-Type Sprinkler (ECOH)OH Group 2 (0.20 gpm/sq.ft)Standard ResponseCoverageArea1W x L,ft x ft(m x m)MinimumFlow 2 ,gpm(lpm)MinimumPressure2 ,psi(bar)16 x 16(4,9 x 4,4)38(144)11.5(0,79)16 x 18(4,9 x 5,5)43(163)14.7(1,01)16 x 20(4,9 x 6,1)48(182)18.4(1,27)16 x 16(4,9 x 4,4)51(193)20.7(1,43)16 x 18(4,9 x 5,5)58(220)26.8(1,85)16 x 20(4,9 x 6,1)64(242)32.7(2,25)Top ureRatingMinimumSpacing4,ft(m)6 to 12(150 to 300)155 F, 200 F(68 C, 93 C)8(2,4)Notes:1. Backwall (where sprinkler is located) by sidewall (length of throw).2. Requirement is based on minimum flow in GPM from each sprinkler. The indicated residual pressures are based on the nominal K-factor of 11.2.3. The centerline of the sprinkler waterway is located below the deflector as shown in Figures 2, 3, and 4.4. Minimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (that is, sidewall sprinklers on an adjacent wall,on an opposite wall, or pendent sprinklers) must be located outside of the maximum listed protection area of the extended coverage sidewall sprinkler being utilized.TABLE CSERIES DS-3 EXTENDED COVERAGE HORIZONTAL SIDEWALL DRY-TYPE SPRINKLERSUL AND C-UL LISTING COVERAGE AND FLOW RATE CRITERIATemperatures for Heated Area150 F(10 C)60 F(16 C)The configuration shown in Figure 7 isonly applicable for wet pipe systemswhere the sprinkler fitting and waterfilled pipe above the sprinkler fitting arenot subject to freezing and where thelength of the Dry-Type Sprinkler has theminimum exposure length depicted inFigure 10. Refer to the Exposure Lengthsection.Ambient TemperatureExposed toDischarge End of Sprinkler40 F(4 C)40 F(4 C)00030 F(-1 C)00020 F(-7 C)4(100)00For wet pipe system installations of 1inch NPT Series DS-3 Dry-Type Sprinklers connected to CPVC piping, useonly the following TYCO CPVC fittings:10 F(-12 C)8(200)1(25)0 1 in. x 1 in. NPT Female Adapter(P/N 80145)0 F(-18 C)12(305)3(75)0 1 in. x 1 in. x 1 in. NPT SprinklerHead Adapter Tee (P/N 80249)-10 F(-23 C)14(355)4(100)1(25)-20 F(-29 C)14(355)6(150)3(75)-30 F(-34 C)16(405)8(200)4(100)-40 F(-40 C)18(455)8(200)4(100)-50 F(-46 C)20(510)10(255)6(150)-60 F(-51 C)20(510)10(255)6(150)Minimum Exposed Barrel Length2 ,Inches(mm)Notes:1. For protected area temperatures that occur between values listed above, use the next cooler temperature.2. These lengths are inclusive of wind velocities up to 30 mph (18,6 kph).TABLE DEXPOSED SPRINKLER BARRELS IN WET PIPE SYSTEMSMINIMUM RECOMMENDED LENGTHSFor dry pipe system installations, useonly the side outlet of maximum 2-1/2inch reducing tee when locating SeriesDS-3 Dry-Type Sprinklers directlybelow the branch line. Otherwise, usethe configuration shown in Figure 6 toassure complete water drainage fromabove Series DS-3 Dry-Type Sprinklersand the branch line. Failure to do somay result in pipe freezing and waterdamage.
TFP550Page 4 of 8ORDER LENGTHS:3" to 45-1/4" (76,2 to 1149,4 mm)IN 1/4" (6,4 mm) INCREMENTSFACE OFSPRINKLER FITTING1" NPT,NOMINAL MAKE-IN9/16" (14,3 mm)FACE OFMOUNTINGSURFACE2" 1/8"(50,8 3,2 mm)2-3/4" DIA.(69,9 mm)9/16" (14,3 mm)3-11/16" DIA.(93,7 mm)SPRINKLER FITTING(REFER TO DESIGNCRITERIA SECTION)CENTERLINEOF WATERWAYFIGURE 2SERIES DS-3 ECOH HORIZONTAL SIDEWALL DRY-TYPE SPRINKLERWITH FLUSH ESCUTCHEON (TY5339)ORDER LENGTHS:1" to 44" (25,4 to 1117,6 mm)IN 1/4" (6,4 mm) INCREMENTSFACE OFMOUNTINGSURFACEFACE OFSPRINKLER FITTING2-3/4" DIA.1" NPT,(69,9 mm)NOMINAL MAKE-IN9/16" (14,3 mm)4-1/8" 3/8"(104,8 9,5 mm)9/16" (14,3 mm)3-1/2" DIA.(88,9 mm)SPRINKLER FITTING(REFER TO DESIGNCRITERIA SECTION)CENTERLINEOF WATERWAYFIGURE 3SERIES DS-3 ECOH HORIZONTAL SIDEWALL DRY-TYPE SPRINKLERWITH DEEP ESCUTCHEON (TY5339)ORDER LENGTHS:5-1/4" to 48" (133,4 to 1219,2 mm)IN 1/4" (6,4 mm) INCREMENTSFACE OF SPRINKLER FITTING1" NPT,NOMINAL MAKE-IN9/16" (14,3 mm)SPRINKLER FITTING(REFER TO DESIGNCRITERIA SECTION)MINIMUM2-1/4" (57,2 mm)DEFLECTOR TOMOUNTINGSURFACE9/16"(14,3 mm)CENTERLINEOF WATERWAYFIGURE 4SERIES DS-3 ECOH HORIZONTAL SIDEWALL DRY-TYPE SPRINKLERWITHOUT ESCUTCHEON (TY5339)NOTICEDo not install Series DS-3 Dry-TypeSprinklers into any other type fittingwithout first consulting the TechnicalServices Department. Failure to use theappropriate fitting may result in one ofthe following: failure of the sprinkler to operateproperly due to formation of iceover the Inlet Plug or binding of theInlet Plug insufficient engagement of theInlet pipe-threads with consequentleakageDrainageIn accordance with the minimumrequirements of the NATIONAL FIREPROTECTION ASSOCIATION for drypipe sprinkler systems, branch, cross,and feed-main piping connected to DrySprinklers and subject to freezing temperatures must be pitched for properdrainage.Exposure LengthWhen using Dry Sprinklers in wet pipesprinkler systems to protect areassubject to freezing temperatures, useTable D to determine a sprinkler’sappropriate exposed barrel length toprevent water from freezing in the connecting pipes due to conduction. Theexposed barrel length measurementmust be taken from the face of thesprinkler fitting to the surface of thestructure or insulation that is exposedto the heated area. Refer to Figure 7 foran example.For protected area temperaturesbetween those given above, theminimum recommended length fromthe face of the fitting to the outside ofthe protected area may be determinedby interpolating between the indicatedvalues.Clearance SpaceIn accordance with NFPA 13, whenconnecting an area subject to freezing and an area containing a wet pipesprinkler system, the clearance spacearound the sprinkler barrel of Dry-TypeSprinklers must be sealed. Due totemperature differences between twoareas, the potential for the formation ofcondensation in the sprinkler and subsequent ice build-up is increased. Ifthis condensation is not controlled, icebuild-up can occur that might damagethe Dry-Type Sprinkler and/or preventproper operation in a fire situation.Use of the Model DSB-2 Dry Sprinkler Boot, described in Technical DataSheet TFP591 and shown in Figure 9,can provide the recommended seal.
TFP550Page 5 of 8DSB-2INTENDEDRUNOUTLET FOR FREEZERPLUGGED STRUCTURESTO DRYSYSTEMSPRINKLERFITTING(SEE DESIGNCRITERIASECTION)DSB-2INTENDEDFOR FREEZERSTRUCTURESTO GFIGURE 5SPRINKLER FITTINGUNHEATED 6" (152,4 mm)TO 12" (304,8 mm)CEILING TO TOPOF SPRINKLERDEFLECTORDISTANCE4/12SLOPEMAXIMUMFIGURE 8SPRINKLER PLACEMENTUNDER SLOPED CEILINGSIN LOADING DOCKSSTRAP TIES(ENDS ONOPPOSINGSIDES OFBOOT)FACE OFSPRINKLERFITTINGDSB-2INTENDEDFOR FREEZERSTRUCTURESHEATEDAREAFIGURE 6SPRINKLER FITTINGUNHEATED AREA2-3/4" DIA.(69,9 mm)CLEARANCEHOLEADHESIVEEXPOSURELENGTH(SEE DESIGNCRITERIA SECTION)DS-3SHOWNWITH FLUSHESCUTCHEONFIGURE 9MODEL DSB-2 DRY SPRINKLERBOOT WITH SERIES DS-3DRY-TYPE PENDENT SPRINKLERFIGURE 7SPRINKLER FITTINGHEATED AREA
TFP550Page 6 of 8InstallationWRENCH FLATENGAGEMENTAREATYCO Series DS-3 Dry-Type Sprinklers,11.2K Horizontal Sidewall, StandardResponse, Extended Coverage, Ordinary Hazard (ECOH) must be installedin accordance with this section.General InstructionsSeries DS-3 Dry-Type Sprinklers mustonly be installed in fittings that meetthe requirements of the Design Criteria section. Refer to the Design Criteriasection for other important requirements regarding piping design andsealing of the clearance space aroundthe Sprinkler Casing. With reference toFigure 10, do not grasp the sprinklerby the deflector. Failure to follow thisinstruction may impair performance ofthe device.Do not install any bulb-type sprinklerif the bulb is cracked or there is a lossof liquid from the bulb. With the sprinkler held horizontally, a small air bubbleshould be present. The diameter of theair bubble is approximately 1/16 in.(1,6 mm) for the 135 F (57 C) rating to1/8 in. (3,2 mm) for the 360 F (182 C)rating.A leak-tight 1 inch NPT sprinkler jointshould be obtained by applying a minimum-to-maximum torque of 20 to30 lb-ft (26,8 to 40,2 N·m). Higherlevels of torque may distort the sprinkler Inlet with consequent leakage orimpairment of the sprinkler.Do not attempt to compensate forinsufficient adjustment in an escutcheon plate by under or over-tighteningthe Sprinkler. Re-adjust the position ofthe sprinkler fitting to suit.Step 1. Install horizontal sidewall sprinklers with the center line of waterwayparallel to the ceiling and perpendicular to the back wall surface. The word“TOP” on the deflector must faceupwards toward the ceiling.Step 2. With a non-hardening pipethread sealant such as TEFLON appliedto the Inlet threads, hand-tighten thesprinkler into the sprinkler fitting. Donot grasp the sprinkler by the deflector(Ref. Figure 10).Step 3. Wrench-tighten the sprinklerusing either: a pipe wrench on the Inlet Band orthe Casing (Ref. Figure 1) the W-Type 8 Sprinkler Wrench onthe Wrench Flat (Ref. Figure 11)Apply the Wrench Recess of theW-Type 8 Sprinkler Wrench to theWrench Flat.WRENCHFLATSAPPLYWRENCH ASSHOWNFIGURE 10DO NOT GRASPDEFLECTORFIGURE 11W-TYPE 8SPRINKLER WRENCHNote: If sprinkler removal becomesnecessary, remove the sprinkler usingthe same wrenching method notedabove. Sprinkler removal is easier whena non-hardening sealant was usedand torque guidelines were followed.After removal, inspect the sprinkler fordamage.mine the cause of leakage; for example,an improper installation or an ice plug.Close the fire protection system controlvalve and drain the system beforeremoving the sprinkler.Step 4. After applying a wall finish,slide on the outer piece of the escutcheon until it comes in contact with themounting surface.For Deep Escutcheons, slide the outerskirt over the inner cup to make firmcontact with the mounting surface.Care andMaintenanceTYCO Series DS-3 Dry-Type Sprinklers,11.2K Horizontal Sidewall, StandardResponse, Extended Coverage, Ordinary Hazard (ECOH) must be maintained and serviced in accordance withthis section.Before closing a fire protection systemmain control valve for maintenancework on the fire protection systemthat it controls, obtain permission toshut down the affected fire protectionsystems from the proper authoritiesand notify all personnel who may beaffected by this action.Absence of the outer piece of anescutcheon, which is used to cover aclearance hole, may delay the time tosprinkler operation in a fire situation.A Vent Hole is provided in the Bulb Seat(Figure 1) to indicate if the Dry Sprinkleris remaining dry. Evidence of leakagefrom the Vent Hole indicates potential leakage past the Inlet seal and theneed to remove the sprinkler to deter-Sprinklers which are found to beleaking or exhibiting visible signs ofcorrosion must be replaced.Automatic sprinklers must never bepainted, plated, coated, or otherwise altered after leaving the factory.Modified sprinklers must be replaced.Sprinklers that have been exposed tocorrosive products of combustion, buthave not operated, should be replacedif they cannot be completely cleanedby wiping the sprinkler with a cloth orby brushing it with a soft bristle brush.Care must be exercised to avoiddamage to the sprinklers – before,during, and after installation. Sprinklers damaged by dropping, striking,wrench twist/slippage, or the like, mustbe replaced. Also, replace any sprinklerthat has a cracked bulb or that has lostliquid from its bulb. (Refer to Installation Section.)The owner is responsible for the inspection, testing, and maintenance of theirfire protection system and devices incompliance with this document, as wellas with the applicable standards of theNATIONAL FIRE PROTECTION ASSOCIATION (e.g., NFPA 25), in addition tothe standards of any other authoritieshaving jurisdiction. Contact the installing contractor or product manufacturerwith any questions.Automatic sprinkler systems are recommended to be inspected, tested,and maintained by a qualified Inspection Service in accordance with localrequirements and/or national codes.
TFP550Page 7 of 8P/N* 61 — XXX — X — ASSPLATED4SIGNAL WHITE(RAL9003)POLYESTERSIGNAL SCUTCHEON TYPE161Flush Escutcheon(1 in. NPT), 155 F (68 C)163Flush Escutcheon(1 in. NPT), 200 F (93 C)171Deep Escutcheon(1 in. NPT), 155 F (68 C)173Deep Escutcheon(1 in. NPT), 200 F (93 C)151Without Escutcheon(1 i
Ordinary Hazard Horizontal Sidewall, Dry-Type Sprinklers are designed for extended coverage use in ordinary hazard occupancies (ECOH) per NFPA 13 Series DS-3 Dry-Type Sprinklers provide protection of coverage areas up to 16 ft x 20 ft (320 ft 2) as compared to standard coverage horizontal side-wall sprinklers having a maximum cov -
Taking Advantage on In-Network Cost-Share Accessing Out-of-Network Cost-Share Member sees a Kelsey-Seybold Clinic PCP 0 Member sees an out-of-network PCP 10 Member sees a Kelsey-Seybold Clinic specialist 25 Member sees an out-of-network specialist 35 Member sees an affiliate provider contracted with Kelsey 25 Member sees an MD Anderson .
Independent Personal Pronouns Personal Pronouns in Hebrew Person, Gender, Number Singular Person, Gender, Number Plural 3ms (he, it) א ִוה 3mp (they) Sֵה ,הַָּ֫ ֵה 3fs (she, it) א O ה 3fp (they) Uֵה , הַָּ֫ ֵה 2ms (you) הָּ תַא2mp (you all) Sֶּ תַא 2fs (you) ְ תַא 2fp (you
NATIONAL GYPSUM CO — Type FSK, Type FSK-G, Type FSW, Type FSW-3, Type FSW-5, Type FSW-G, Type FSK-C, Type FSW-C, Type FSMR-C, Type FSW-6, Type FSL 2K. Gypsum Board* — (As an alternate to Item 2) — 5/8 in. thick gypsum panels, with beveled, square, or tapered edges, applied either horizontally or vertically. Gypsum panels fastened to framing with 1-1/4 in. long Type W coarse
8 SOLUTIONS 2.1 2.2 In (a), the transistor sees Vgs VDD and Vds VDS.The current is In (b), the bottom transistor sees Vgs VDD and Vds V1.The top transistor sees Vgs VDD - V1 and Vds VDS - V1.The currents are Solving for V1, we find Substituting V1 indo the IDS2 equation and simplifying gives IDS1 IDS2. 2.3 The body effect does not change (a) because Vsb 0.
scissors; marker; light-blue and dark-blue construction paper Sing It Out—Sing a song about how God sees us. CD player Bible Craft—Sponge-paint boat pictures. Rectangle and triangle sponges, brown and white tempera paint, blue construction paper, glue, craft sticks, plastic tablecloth, shallow pans, scissors, paint shirts
Before an all -new MAZDA 6 ever sees the light of day, it sees an innovative, 34 -step, airless painting process. One that imparts a rich, virtually fl awless fi nish. And protection from color fading designed to last a decade. It also sees the scrutiny of over 100 inspectors. Each empowered to reject any part or component that fails to
Before an all -new MAZDA 6 ever sees the light of day, it sees an innovative, 34 -step, airless painting process. One that imparts a rich, virtually fl awless fi nish. And protection from color fading designed to last a decade. It also sees the scrutiny of over 100 inspectors. Each empowered to reject any part or component that fails to
TCK : K type thermocouple TCE : E type thermocouple TCJ : J type thermocouple TCB : B type thermocouple TCR : R type thermocouple TCS : S type thermocouple TCT : T type thermocouple TCN : N type thermocouple TCG : G type thermocouple TCC : C type thermocouple TCD : D type thermocouple RTD : Pt100 CU53: V.10 : 0 10 mV input V.50 : 0 50 mV input
