GENERAL INSTRUCTIONS – PLEASE READ BEFORE REFILLINGThank you for purchasing a Uni-Kit toner refill kit. If you have any questions about the use ofthese products, please check our FAQ’s below or email our technical support at support@uni-kit.com. Uni-Kit is dedicated to providing high quality products at prices that allow our customersto save significantly compared to buying original cartridges. Refilling your toner cartridge alsohelps the environment as your empty toner cartridge can be revived instead of landing up in alandfill.The refilling procedure is simple in most cases – make a hole (or uncover a hole) in the cartridge,refill it, and seal it. For specific instructions on your specific model please locate your model inour instruction booklet. While refilling a toner cartridge poses no significant risk to your health,we ask you to refill outside whenever possible and always use common sense when handling thetoner hole making tool or when pouring the toner.Using the toner hole making tool:This tool is an electrical appliance that is used to make a hole in the cartridge by first heatingup to a desired temperature. Be careful when handling this tool so that you don’t burn yourselfor anything around you, the tool gets very HOT! You will need to wait for the tool to heat upfor about 3-5 minutes before using it to burn a hole in the desired location on the cartridge (seespecific cartridge instructions for location of hole). While waiting for the tool to heat up or cooldown, rest the tool on the tool stand as shown in this diagram above.Pouring the toner:To our knowledge, the average DIY refiller’s exposure to fumes presents no significant healthhazard in normal use. We recommend refilling in a well ventilated room or outside to minimizethe exposure to fumes. For extra protection, wear a dust mask.FAQ’s FOR THE UNI-KIT TONER REFILL KITS1. Will your toner harm my printer or photocopier?If you follow our simple instructions and inspect your work before reinstalling your cartridge,there is no way the cartridge you refill can harm your machine.3. Are there any hazards involved with the handling of toner?HP describes toner as “Toner is a nontoxic substance composed of plastic, iron, and a small amountof pigment.”Much like the fumes released from gasoline in cars or from active or passive smoking or evenfrom inert dust and chemicals in the environment, the exposure to fumes from toner or from burning a hole in the cartridge (when necessary) could of course be hazardous. To our knowledge, theaverage DIY refiller’s exposure to fumes presents no significant health hazard in normal use. Werecommend refilling in a well ventilated room or outside to minimize the exposure to fumes. Forextra protection, wear a dust mask.4. How many times can I refill my toner cartridge?An average of three times (It varies depending on cartridge type). The range is from 1 or 2 times, to5 or more times. Quality and page yield will decrease the more times a cartridge is refilled. Whilewe have had reports from some users that they have been able to use our toner an even greaternumber of times on a given empty, the simple (and obvious) rule of thumb is, continue to use ourtoner until you are no longer satisfied with the print quality.5. Why are the kits named after formulas instead of names of printers?The “engine” in your laser printer is also manufactured to be used in dozens, even hundreds ofother printers.Canon actually makes all of the Hewlett Packard laser printers and toner cartridges. Hewlett Packard does not make a single laser printer nor do they make a single toner cartridge.6. If the refilled cartridge using your toner won’t hurt the printer, what, if anything, can gowrong?Just like a new cartridge, if there is ever anything that goes wrong, it normally shows up on theprinted output. If you notice spots, dots, blank spots or voids showing up on the printed page (ina pattern that repeats several times down the page), then the cartridge has reached the end of itsuseful life and needs to be replaced. A razor sharp, pencil thin line appearing on the page alsoindicates a cartridge has reached the end of the line.7. Is your toner made by the same company that makes the brand-name cartridge toner?There is no way to know for sure. Many laser printer manufacturers do not make their own toner.We use toner formulas that match as closely as possible the properties of the original toner theyare replacing. Our toners are tested not only for excellent quality prints like the original, but alsofor page yield so that you get about the same amount of printed pages as the original cartridge onthe first refill.2. Will the use of your toner void my warranty?Nope! In fact, it is against the law (the Sherman and Clayton Anti-Trust Acts, to be specific) totie the purchase or use of a particular supply to the warranty. All rights reserved, Easy Group, . Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.I
Monochrome Printers - Listed by Cartridge ModelApple - M0089Apple - M0180Apple - M2045GAApple - M2473A / GApple - M6002Brother -- TN250Brother – TN350Brother – TN330/360Brother – TN430/460/560Brother – TN540/550/570/580Brother – TN9500Brother – TN9500 (high yield)Canon - A30, A15Canon - E16/E20/E31/E40Canon – EP52Canon – EP52 (high yield)Canon – EPACanon – EPBCanon – EPC/A20Canon - EPECanon – EPW/EP72Canon – F100Canon - FX1/EPLCanon - FX2/EPPCanon -- FX3Canon – FX4 30 Genicom – 6A0133P01/6A0Canon - FX5 31 134P0149 Canon - L50 851 Canon – S35 9 HP - HP P1005 / P1006 /54 Canon – X25 9 P150531 Canon – XS/EPS 50 HP - 92274A50 Canon -- FX8 12 HP - 92275ACanon -- FX9/FX10/104 13 HP - 92285A1 Canon -- Cartridge 106 14 HP - 92291AHP - 92295AX23 DEC -LON0XXAA 31 HP - 92298A / X4 DEC - LN07XAA 49 HP - C3900A5 DEC LN11XAA 29 HP - C3903AHP - C3906A35HP - C3909A36 Dell 1100 / Samsung MLHP – C4092A2010 / ML-1610 / SamsungHP – C4096A11 SCX-4321 / SCX-4521 /7 Xerox PE220 and more 18 HP - C4127A35 Dell S-35 15 HP - C4127X36 Dell P1500 16 HP - C4127AX/C4182AX32 Dell P1600 17 HP - C4129X48 Dell M5200 72 HP - C7115AHP - C7115X5131 Epson – S0500100 28 HP - C8061A47 Epson - S051016 29 HP - C8061X10 Epson - S051011 29 HP - Q1339A49 Epson – S051009/S051200 27 HP - Q2610A54 Epson – S051023 26 HP - Q2612AHP - Q2613A / X32 All rights reserved, Easy Group, . Version 5.0HP - Q2624A4374 HP - Q5949A67HP - 594244HP - C7553A/C7553X6066 HP - C7551A/C7551X6154 HP - 8543X644951 IBM Info Print 13121645 IBM – 63H5721475031 Lexmark - 08A0477/08A0478 1548 Lexmark – 10S01509630 Lexmark – 1382100/1382150/32 1380850/1380950/1380200/47 1380520 7433 Lexmark – 1382140 4734 Lexmark - 1382760 7035 Lexmark – 13T0101 7636 Lexmark - 140100A 4847 Lexmark – 140109A 7563 Lexmark - 140195AX 5037 Lexmark - 140198A / X 3138 Lexmark - 17G0152, 17G0154,52 4K00198, 4K00199 12A5740,39 1382625, 1382925, 138292946 12A5745, 12A5840, 12A5845,40 12A5849 7141 Lexmark E220/E321/E323 1642 Lexmark T630/T632/T634/T640/ 72-73All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.II
Monochrome Printers - Listed by Cartridge ModelOKIDATA 52111401 106Lexmark E120 19 Panasonic – FQU160 27Lexmark C910/C912/C920 78PITNEY BOWES 8060 49Minolta 4161101,/1710434001 106 PITNEY BOWES 8186 106Minolta 0910802/0910803 27Minolta - 0927605, 0927606 29 RICOH 339302 50Minolta - 17030190000 50 RICOH 339473 106Minolta - 17030210000 51 RICOH 339479 106Minolta - 1710081001 48Minolta - 1710433001/0938306 106 Samsung – ML 1710 95Minolta - 171046601Samsung – ML6060 111171046001 47 Samsung – SF5100 /Minolta – 1710497001 111 TDR510P / ML4500 /Minolta – 1710511001,96ML12101410399002,Samsung – ML5000/1710405002,TD55K 764152601/4152301 28 Samsung ML-7000 102-103Minolta 1300/1350 81 Samsung ML-1510,ML-2250, SCX-D4200A 101MURATEC/MURATA TS120 106 Samsung ML-2010 / ML1610 / Samsung SCX-4321NEC 20055 27 / SCX-4521 18NEC 20090 106 Samsung 3050 104NEC 20120/20122 28 Samsung ML2150/ML2151/NEC 20152 111 ML2152/ML2155/ML2550/NEC S2526 106 ML2551/ ML2552 105Sharp – AL100TDSharp - FO45NDSharp - Z781701,ZT50701Sharp - ZT20TD1112106110107Xerox - 106R441/106R442 111Xerox - 6R359, 6R343,6R333, 6R881, 6R737 110Xerox – 106R482 113Xerox - 6R899 109Xerox - 6R905 30Xerox - 6R907 48Xerox - 6R908 32Xerox – 6R914 112Xerox - 6R926 36Xerox – 6R927 33Xerox – 6R928 34Xerox - 6R929/6R0906 47Xerox – 6R932 37Xerox – 6R933 39Xerox – 113R296 76Xerox 6R916/9R917 108Xerox - 013R00621 18 All rights reserved, Easy Group, . Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.III
Color Printers - Listed by Printer Model59 Xerox 7300Xerox 7400Lexmark C510/C71077 Xerox 7750 / 7760Lexmark C910/C912/C92078Lexmark C522 79-80HP 9500114115116Brother HL4040CN, HL4070CDW,6MFC9440CN, MFC9840CDWBrother HL4200 Series 22-23 Okidata C340090Brother HL-2700CN/ MFC-9420CN 77 Okidata C5100 / C5150/C5200/C5300/C5400 C7100/ C7200/C7300 /Canon RUNNER 3200 59C7500/ B4100 / B4200 /B430089Okidata C5500/C58009124Dell 1320Dell 3100 20-21 Konica Minolta QMS 2200/2400/2500 87-8825 Konica Minolta QMS 2300/2350/ 84-86Dell 3110Dell 5100 22-23 Konica Minolta QMS 5430 82-83Epson C1100 (CX11) 20-21 Ricoh CL35009487 Ricoh CL4000 / SP C410 / C411Epson C1000 / C2000 / C30009284 Ricoh CL7000 / CL7200EPSON C900/ C190093Ricoh Aficio CL1000N77HP 1500 / 2500 / 2550 / 2800 / 2840 /53 Samsung CLP 3002820 285010055 Samsung CLP 500HP 1600/26009956 Samsung CLP 510HP 3500 / 4500 / 4600 / 55009862 Samsung CLP 600HP 3600 / 3800 / 47009769HP CP121568 Xerox 6130HP CP40052457 Xerox C525A 20-21HP 850058 Xerox 6250, Xerox 6300 Series 22-23HP 8500 Drum Chip Replacement All rights reserved, Easy Group, . Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.IV
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXBrother – TN250REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Formula 7A) 1 funnel cap 1 hole plugGeneral Refilling Procedures:Using your thumb, lift up the black plastic tab so that it unlocks from the cartridgebody. Rotate the entire black piece toward you. This will reveal a toner filling port.Before opening the bottle of toner, turn it upside down and tap it on a table to loosen thetoner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attachthe funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling holeand insert it into the hole. If the toner stops flowing before the cartridge is full, simplyremove the toner, close the cap, turn the bottle upside down and tap it on a table. Oncethe cartridge is full, twist the entire black plastic piece away from you until the tablocks back in place.23 All rights reserved, Easy Group, LLC. Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.1
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXBrother – TN350REQUIRED FOR A SUCCESSFUL REFILL:Refill Hole Toner (Uni-Kit Refill Kit for TN350) 1 funnel capGeneral Refilling Procedures:Use a flathead screwdriver to pop out the large plastic plug found on the side of the sideof the cartridge.IMPORTANT: You must dispose of any original toner in the cartridge as much aspossible before refilling. Dispose of toner properly into a trash can, or use a vacuumwith a hose for best results (if possible).Before opening the bottle of toner, turn it upside down and tap it on a table to loosenthe toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full,simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.Once the cartridge is full, seal the hole with the plug by twisting it until it is completelyseated. Now gently shake the cartridge side to side to distribute the toner.Installing Reset Gear on Starter CartridgesUsing the illustration below as a guide, remove the 3 screwsindicated with red arrows. Once the screws have beenremoved, carefully and gently detach the side panel.The picture on the right shows how the gearshould be set once it has been placed withinthe panel. To insert the gear in this panel,slide the flag (which is the longest part of thegear) through the right side opening (greenarrow on right side) and then slide the gear tothe left. Once you have done this, hold theflag in place and place the panel back on thecartridge. Place the screws back in place andyour cartridge is ready to be used. All rights reserved, Easy Group, LLC. Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.2
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.Brother – TN330 / TN360CLICK HERE TO GO THE INDEXREQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Refill Kit for TN330/360) 1 funnelGeneral Refilling Procedures:Use a flathead screwdriver to pop out the large plastic plug found on the side of the sideof the cartridge.IMPORTANT: You must dispose of any original toner in the cartridge as much aspossible before refilling. Dispose of toner properly into a trash can, or use a vacuumwith a hose for best results (if possible).Before opening the bottle of toner, turn it upside down and tap it on a table to loosenthe toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full,simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.Once the cartridge is full, seal the hole with the plug by twisting it until it is completelyseated. Now gently shake the cartridge side to side to distribute the toner.Refill HoleInstalling Reset Gear on Starter CartridgesRemove screws todetach panel for resetting1. Remove the screws circled in red in the illustrationabove. Carefully detach the panel from the cartridge.2. Reset the flag gear by turning it into the correctposition. The picture on the right shows the flag gearin the correct position.The flag gear here is inthe correct position3. Screw the panel back into place, and your cartridge is ready. All rights reserved, Easy Group, LLC. Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.3
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXBrother – TN430/460/560REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Formula 7A) 1 funnel cap 1 hole plug Toner Hole Making ToolGeneral Refilling Procedures:CRITICAL NOTE: You must remove all of the remaining old toner BEFORE refillingotherwise you will get gray hazy prints.Use a flathead screwdriver to pop out the large plastic plug found on the side of the sideof the cartridge.Before opening the bottle of toner, turn it upside down and tap it on a table to loosenthe toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full,simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.Once the cartridge is full, seal the hole with the plug by twisting it until it is completelyseated. Now gently shake the cartridge side to side to distribute the toner. All rights reserved, Easy Group, LLC. Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.4
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXBrother – TN540 / 550 / 570 / 580REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Refill Kit for TN550/580) 1 funnel capRefill HoleGeneral Refilling Procedures:Use a flathead screwdriver to pop out the large plastic plug found on the side of the sideof the cartridge.IMPORTANT: You must dispose of any original toner in the cartridge as much aspossible before refilling. Dispose of toner properly into a trash can, or use a vacuumwith a hose for best results (if possible).Before opening the bottle of toner, turn it upside down and tap it on a table to loosenthe toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full,simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.Once the cartridge is full, seal the hole with the plug by twisting it until it is completelyseated. Now gently shake the cartridge side to side to distribute the toner.Installing Reset Gear on Starter Cartridges1. Remove the screws circled in red in the illustrationabove. Carefully detach the panel from the cartridge.2. Set the flag gear spring on the gear post as shownabove. Set the small end of the spring on the slot onthe gear post. All rights reserved, Easy Group, LLC. Version 5.02. Place the flag gear on the post and position the springas shown above.All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.5
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXBrother – TN110/TN115REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Refill Kit for TN110/TN115) 1 funnel cap\ Flathead screw driverGeneral Refilling Procedures:Use a Flathead screwdriver to pop out the large plastic plug found on the side of the side of thecartridge.IMPORTANT: You must dispose of any original toner in the cartridge as much as possible beforerefilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results(if possible). For the TN-110, please be sure you only use half the toner in the bottle. Do notoverfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can andwill damage a cartridge.Refill HoleBefore opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner andallow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. Ifthe toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn thebottle upside down and tap it on a table. Once the cartridge is full, seal the hole with the plug bytwisting it until it is completely seated. Now gently shake the cartridge side to side to distribute thetoner.Resetting the counter (Reset Gear)Using the illustration below as a guide, remove the 2 screwsindicated with red circles. Once the screws have beenremoved, carefully and gently (with a Flathead screwdriver)unlock the side panel and remove the side cap.Carefully pull backto UnlockAfter removing the side panel (as instructedon the left); The 2 pictures on the right showhow the gear should be set in order to resetthe counter. Carefully remove the gear andthe pin holding it in place. Turn the gearclock wise and replace it so that it meshesand matches the “Properly Resetted” pictureto the right. Re-install the pin so that it holdsthe gear down. Once the gear is resetted,re-install the side cap, and place the screwsfirmly back in place. Your cartridge is readyto be used. All rights reserved, Easy Group, LLC. Version 5.0Not ResettedProperly ResettedAll trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.6
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXCanon - E16/E20/E31/E40REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Formula 2A) 1 funnel cap 1 hole plug Toner Hole Making ToolGeneral Refilling Procedures:Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutesbefore using. Position the copper bit on the cartridge in the spot indicated by the photograph and push gently until it melts a hole in the cartridge. Remove the tool, place itback on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,it must be removed, as this can damage your cartridge or cause print defects. If thepiece remains in the tool, wait for the tool to cool down and pry it out.Before opening the bottle of toner, turn it upside down and tap it on a table to loosen thetoner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attachthe funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling holeand insert it into the hole. If the toner stops flowing before the cartridge is full, simplyremove the toner, close the cap, turn the bottle upside down and tap it on a table. Oncethe cartridge is full seal the hole with the plug.Do not press down on the plug since the cartridge is resting on a table this can actuallydamage the photo-optic drum. Instead hold one end of the cartridge up off the tableand twist the plug until it fully sealed. Now gently shake the cartridge side to side todistribute the toner. All rights reserved, Easy Group, LLC. Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.7
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXCanon - L50REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Formula 1A) 1 funnel cap 1 hole plug (electrical or duct tape will do as well) Toner Hole Making ToolGeneral Refilling Procedures:Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutesbefore using. Position the copper bit on the cartridge in the spot indicated by the photograph and push gently until it melts a hole in the cartridge. Remove the tool, place itback on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,it must be removed, as this can damage your cartridge or cause print defects. If thepiece remains in the tool, wait for the tool to cool down and pry it out.IMPORTANT: You must dispose of any original toner in the cartridge as much aspossible before refilling. Dispose of toner properly into a trash can, or use a vacuumwith a hose for best results (if possible).Before opening the bottle of toner, turn it upside down and tap it on a table to loosen thetoner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attachthe funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling holeand insert it into the hole. If the toner stops flowing before the cartridge is full, simplyremove the toner, close the cap, turn the bottle upside down and tap it on a table. Oncethe cartridge is full seal the hole with the plug or electrical tape (Duct tape will do aswell).With the hole makingtool, make a refill holehereNote: If there are gears that rotate near the refill hold created, do not use the plug,instead use electrical tape or duct tape to seal the hole.Gently rock the cartridge from side to side for about 5-10 seconds to distribute thetoner in the hopper. Your cartridge is now ready for use. All rights reserved, Easy Group, LLC. Version 5.0All trademarks are property of their respective owners. Uni-Kit has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.8
Please be advised that some toner refill kits may becompatible with multiple toner cartridges.CLICK HERE TO GO THE INDEXCanon – S35Canon – X25REQUIRED FOR A SUCCESSFUL REFILL: Toner (Uni-Kit Formula 1A) 1 funnel cap 1 hole plug Toner Hole Making ToolGeneral Refilling Procedures:Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutesbefore using. Position the copper bit on the cartridge in the spot indicated by the photograph and push gently until it melts a hole in the cartridge. Make sure to keep thehole on the flat surface of the cartridge and not on the curved edge. Remove the tool,place it back on its stand and unplug it. If the small piece of plastic has fallen into thecartridge, it must be removed, as this can damage your cartridge or cause print defects.If the piece remains in the tool, wait for the tool to cool down and pry it out.Before opening the bottle of toner, turn it upside down and tap it on a table to loosen thetoner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attachthe funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling holeand insert it into the hole. If the toner stops flowing before the cartridge is full, simplyremove the toner, close the cap, turn the bottle upside down and tap it on a table. Oncethe cartridge is full seal the hole with the plug.Do not press down on the plug since the cartridge is resting on a table this can actuallydamage the photo-optic drum. Instead hold one end of the cartridge up off the tableand twist the plug until it fully sealed. Now gently shake the cartridge side to side todistribute the toner.NOTE: If after the cartridge is refilled and it starts to print gray smudges or smearsalong the margin, the waste hopper could be full. Please refer to the supplemental instructions (page 2) for emptying the waste hopper.Waste Hopper Instructions for Canon S35 / X25:(Do this procedure over a newspaper)Turn the cartridge right side up. Using the hole making tool, position the copperbit on the cartridge in the spot indicated by the photograph and push gently untilit melts a hole in the cartridge. Once the hole has been made, turn the cartridgeover so that t
indicates a cartridge has reached the end of the line. 7. Is your toner made by the same company that makes the brand-name cartridge toner? There is no way to know for sure. Many laser printer manufacturers do not make their own toner. We use toner formulas that match as closely as possible the properties of the original toner they are replacing.
read instructions carefully before attempting to assemble or service the marley engineered products ceiling fan. failure to comply with instructions could result in personal injury and/or property damage. retain for future reference. read and save these instructions important safety instructions 1. caution: read and follow instructions carefully
NA-140VG4 NA-148VG4 Operating Instructions & Installation Instructions Washing Machine (Domestic use) Thank you for purchasing this appliance. - For optimum performance and safety, please read these instructions carefully. - Before connecting, operating or adjusting this appliance, please read the instructions completely.
product-specific operating instructions and the "General Operating Instructions for ProMinent Solenoid Metering Pumps". Both sets of operating instructions are only valid when read together. Part no. 986356 Original Operating Instructions (2006/42/EC) BA BE 025 07/11 EN Please carefully read these operating instructions before use! · Do not .
instructions before using any tool or equipment. IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS WARNING: Read all instructions before operating jump-starter. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. GENERAL SAFETY WARNINGS AND INSTRUCTIONS
Metacafe General Medio General MediaFLO General Martha Stewart Living Omnimedia General Lexico General Internet Broadcasting (IBSYS) General Hearst-Argyle General Harvard Business Review General Greystripe General Friendster General Facebook General Enpocket General Emmis Interactive General Cellfish Media General Company Member Type .
1. Read instructions. Read the safety and operating instructions before operating the appliance. 2. Retain instructions. Retain the safety and operating instructions for future reference. 3. Heed warnings. Observe all warnings on the appliance and in the operating instructions. 4. Follow instructions. Follow all operating and use instructions. 5.
NA - 140VG3 NA - 168VG3 NA - 148VG3 Thank you for purchasing this appliance. - For optimum performance and safety, please read these instructions carefully. - Before connecting, operating or adjusting this appliance, please read the instructions completely. Please keep this manual for future reference. NA-168VG3_English.indb 1 2011-1-24 11:24:53
I like to read comic books. They are fun to read. They make me smile. I read them in the morning. I read them in the afternoon. I read them at night. I even read them when I go camping. Comic books are great to read. I Like to Read Comic Books Story level 1st 38. More free stories and books available at www.clarkness.com and www.readinghawk.com.