SHAFTLINER
SHAFTLINERSHAFTLINER
Shaftliner Type XSHAFTLINERGlasRoc Shaftliner is a paperless mold and moistureresistant gypsum board combining reinforcing glass matsand a specially formulated fire and moisture resistive, noncombustible core.GlasRoc Shaftliner offers:GlasRoc Shaftwall Systems1 & 2 Hour FireResistance Ratings L ong term protection (12 months) to weather exposure.The walls of elevator shafts and stairwells are a vital lifeSHAFTLINERsafety link in multi-story buildings. These walls are the A superior water resistant surface that does not inhibitwater vapor permeance. E xcellent fire resistance properties, and numerous firerated designs. A chieves score of 10 for mold resistance perASTM D3273 the best possible scores for this test.main line of defense against fire entering the cavitiesbehind them and spreading rapidly from floor to floor.Gypsum shaftwall systems have replaced traditionalmasonry for interior vertical enclosures includingmechanical enclosures, stairwells, elevatorenclosures, and other mechanical chases. Some inherentadvantages of paperless gypsum shaftwall systems are:lightweight construction, thinner walls, ease and speed ofSpecially formulatedwater resistant coreinstallation and clean up, cost-effective construction.Shaftwall Systems provide one or two hour fireresistance ratings in non-loadbearing configurations andmoisture and mold resistance during construction.Reinforcing glass mats
The systems are designed to withstand the intermittentsurges of air pressure caused by fast moving elevatorcabs. These systems utilize either an I-Stud, C-H Stud ora C-T Stud and J-Track to support layers of 1" (25.4 mm)1/2" [12.7mm] CertainTeed Type C or5/8" [15.9mm] CertainTeed or M2Tech Type X Gypsum BoardGlasRoc Shaftliner Type X and either 1/2" (12.7 mm)CertainTeed Type C or 5/8" (15.9 mm) CertainTeed orM2Tech Type X gypsum boards.EITHER I-STUD, C-H STUD OR C-T STUDS MAY BEUSED IN CONJUNCTION WITH GlasRoc shaftwallsystems. All of the components are noncombustible.Shaftwalls can be erected from oneside, eliminating the need to buildextensive scaffolding.GlasRoc Shaftwall assemblies save money in severalJ-Track1" [25.4mm]GlasRoc Shaftliner Type Xways. With less weight per square area than other shaftenclosures, structural framing requirements are reduced;I, C-H or C-T Studas is the need for heavily reinforced footings. The 2'(610 mm) wide GlasRoc Shaftliner slides quickly into theI-Stud, C-H Stud or C-T Stud and automatically provides1/2" [12.7mm] CertainTeed Type C or5/8" [15.9mm] CertainTeed or M2Tech Type X Gypsum Board24" (610 mm) o.c. spacing. Shaftwalls can be erectedfrom one side, eliminating the need to build extensivescaffolding. No finishing is required on the shaftJ-Trackside of the partition.2-Hour Vertical Shaftwall System1. All construction shall comply with local building codes.2. Only those components specified shall be used whenconstructing any fire or sound rated system. Substitutionsmay adversely affect performance capabilities.3. Unless otherwise specified in the system design, face layer joints of 1/2"(12.7 mm) CertainTeed Type C, 5/8" (15.9 mm) CertainTeed or M2Tech Type X gypsum boards shall be taped and finished with joint compoundas described in “Surface Preparation” section.Code Report ReferencesUL ER3660-02 (IBC and NBCC Compliance)Fire Resistance Rated DesignsUL/cUL U417, U428, U429, U469, U529, V433, V470,W409, W437, W453ULC W446UL ER3660-02Gypsum Association Fire Resistance Design ManualGA-600 (GA WP 7051, WP 7084, WP 7254, WP 7255)For further technical information regarding soundcontrol and fire resistance for Shaftwall Systems contactMarketing Technical Services at 1-800-446-5284.GlasRoc Shaftliner Type X Gypsum Boards for Gypsum Shaftwall Systems Call Toll Free 1-800-446-5284 www.certainteed.com3
Working with the ProductFRAMING AND INSTALLATION1/2" [12.7mm] CertainTeed Type C or5/8" [15.9mm] CertainTeed or M2Tech Type X Gypsum BoardJ-Track1" [25.4mm] GlasRoc Shaftliner Type XI, C-H or C-T Stud1/2" [12.7mm] CertainTeed TypeC or 5/8" [15.9mm] CertainTeed or M2Tech Type X GypsumBoardJ-TrackCuttingInstallationThe score and snap method is a fast andefficient way to cut GlasRoc gypsum board.Steel Framing and Installation of GlasRoc Shaftliner gypsum boards.Steps:1. On the logo side, position a straight edgealong the line of cut.2. Score sheets with a knife or othersuitable tool.3. With a quick, firm motion, snap back awayfrom the face.4. The back can either be cut with a knifeor separated by snapping the piece in theopposite direction.5. Smooth all cut ends and edges to ensuretight joints.To make cutouts, score around the perimeteron the face and back and tap out the wastepiece from the face side. Cutouts can also bemade with a drywall saw.GlasRoc gypsum boards can also be cutwith a saw. For information on avoiding dustinhalation, refer to the Safety Data Sheetavailable on our website, www.certainteed.com. Safety glasses should always be wornwhen using power tools.41. Lay out per construction drawings.2. Install J-Track along the floor and ceilingand vertically at columns or abuttingpartitions, positioning the long legs closestto the shaft. Secure each piece withthe appropriate power driven fastenersspaced a maximum 24" (600 mm).3. Pre plan stud layout 24" (610 mm) o.c.maximum so the terminal stud on eitherend will fall a minimum of 8" (200 mm)from the opening.4. Install GlasRoc Shaftliner gypsum boardsvertically. Cut boards a maximum of 1"(25 mm) less than floor to ceiling height.The leading edge of the first board mustbe attached to the long leg of the verticalJ-Track with 1-5/8" (41 mm) Type S screwsspaced 12" (305 mm) o.c. or by tabs in theJ-Track. Secure the top and bottom edgesusing the same fasteners and spacing orusing the tabs.5. Friction fit an I, C-H or C-T Stud into thetop and bottoms tracks and slide it snuglyagainst the GlasRoc Shaftliner gypsumboards. Make sure the edge of the board isin full contact with the center web of thestud and covered by all of the tabs.6. E rect adjacent GlasRoc Shaftliner gypsumboards by inserting in the top and bottomJ-Track and between the tabs and flangeon the opposite side of the I, C-H orC-T Studs to complete framing. Checkperiodically to ensure they are plumb.Screws are not required for the top andbottom J-Tracks.7. For doors, ducts or other openings installJ-Track as perimeter framing.8. For walls exceeding 12' (3660 mm) inheight, GlasRoc Shaftliner gypsum boardsmay be butted to span the floor-ceilingheight. The shorter panel should be at least24" (600 mm) long or of sufficient lengthto engage at least two I, C-H or C-T Studtabs on each panel edge. End joints shouldfall alternately in the upper and lower 1/3height of the partition. Subsequent buttjoints between adjoining panels should bespaced no closer than 24" (600 mm) inelevation. Joints may be butted together oruse a I, C-H or C-T Stud placed horizontallybetween boards to secure each joint.9. As an option, if required in building codejurisdictions, butt joints in GlasRoc Shaftliner gypsum boards may be backblocked in the cavity by screw attachinga 12" x 24" (300 mm x 600 mm) pieceof 5/8" (15.9 mm) CertainTeed orM2Tech Type X or 1" (25.4 mm) GlasRoc
Shaftliner gypsum board over the joint tothe tabs of the I, C-H or C-T Studs.10. Frame all cut openings in the shaft sidewith J-Track, providing adequatestructural support for openings over48" (1220 mm).11. Elevator door frames must be tied toshaftwall enclosures; however, they mustremain independently supported by thebuilding frame. Attach GlasRoc ShaftwallSystem to elevator door frame jamb andanchor clips with pan head screws. TheJ-Track 3" (76 mm) leg is used at theintersection of the elevator door frameand shaftwall system.12. Where required, use an acoustical sealantto caulk around the perimeter of wallsections, door frames, call boxes and anyother openings that may allow air passage.1-Hour-Rated System: Finished One Side1. Apply a single layer of 5/8" (15.9 mm)CertainTeed Type X gypsum boardvertically with 1" (25 mm) Type S screws.2. Holding the gypsum board firmly againstthe framing, begin fastening in the centerof each sheet and move outward towardends and edges.3. Space screws at 12" (300 mm) o.c. in thefield of the board and 8" (200 mm) o.c.around the perimeter.4. Set fastener heads slightly below thesurface without breaking the face paperor damaging the gypsum core.2-Hour-Rated System: Finished One Side1. Install a base layer of 1/2" (12.7 mm)CertainTeed Type C or 5/8" (15.9 mm)CertainTeed or M2Tech Type X gypsumboard vertically or horizontally with 1"(25 mm) Type S buglehead screws at 24"(600 mm) o.c.2. Apply a face layer of 1/2" (12.7 mm)CertainTeed Type C or 5/8" (15.9 mm)CertainTeed or M2Tech Type X gypsumboard vertically or horizontally (oppositeof base layer) over the face layer with1-5/8" (41 mm) Type S screws spaced at24" (600 mm) o.c.3. All joints in the face layer must bestaggered with respect to those in thebase layer.2-Hour-Rated System: Finished Two Sides1. Follow the preceding framing details usingI, C-H or C-T Studs and J-Track.2. Apply GlasRoc Shaftliner gypsum board,followed by the attachment of 1/2" (12.7mm) CertainTeed Type C or 5/8" (15.9mm) CertainTeed or M2Tech Type Xgypsum board in a single facing layer oneach side of the studs vertically, parallelto framing, with 1" (25 mm) No. 6 Type Sscrews 12" (300 mm) on center.2-Hour-Rated System:Sound Control (STC) Rating of 54A two-hour-rated shaftwall partition can beconfigured to achieve a minimum STC ratingof 50 with the following system.1. F ill wall cavity with 1-1/2" (38 mm)CertainTeed Sustainable Insulation , orequivalent.2. I nstall resilient furring channels, 1/2"(12.7 mm) deep minimum No. 25gauge/0.0188" (0.478 mm) thick, on theface side horizontally to I, C-H or C-TStuds at 24" (610 mm) o.c.3. Secure channels to each stud with 3/8"(10 mm) Type S panhead screws.4. Apply a double layer of 1/2" (12.7 mm)CertainTeed Type C or 5/8" (15.9mm) CertainTeed or M2Tech Type Xgypsum board. Attach the base layer tothe channels using 1" (25 mm) Type Sbuglehead drywall screws spaced 24" (600m m) o.c. along the edges and in the fieldof the board with the first screw 3" (75 mm)from board end. Attach the face layer to thechannels using 1-5/8" (41 mm) No. 6 Type Sbuglehead screws spaced 12" (300 mm) o.c.along the edges and in the field with the firstscrew 6" (150 mm ) from board end.5. Apply caulk, such as Green GlueNoiseproofing Sealant, under the top andbottom tracks and around the exterior faceperimeters of each layer of 1/2" (12.7 mm)CertainTeed Type C or 5/8" (15.9 mm)CertainTeed or M2Tech Type X gypsumboard.1. N o surface treatment shall be done until theinterior temperature has been maintainedat a minimum of 50 F (10 C) for at least 48hours prior to application of compoundsand until all materials have completelydried. Adequate continuous ventilationmust also be provided.2. Embed tape into the wet compound andallow to dry. For inside corners, crease thetape and work it into the joint.3. Apply a second coat of compound acrossthe joint and feather to approximately 4"(100 mm) on each side.4. Apply a third coat and feather toapproximately 6" (150 mm) on each side5. Allow each coat to dry before proceeding.6. Attach corner bead to outside corners andapply three coats of joint compound.Feather out each coat as described insteps 3-5.7. S pot cover all fastener heads with threecoats of joint compound applied indifferent directions.8. A dditional coats of compound may berequired to achieve higher Levels of Finish.9. Lightly sand the last coat of all treatedareas, taking care not to roughen thesurrounding gypsum board paper.Smoothing can also be accomplished witha damp sponge.2-Hour-Rated System:Horizontal Membrane and Duct Protection1. Install the J-Track and I, C-H, or C-T studsystem for two hour construction using 3layers of 1/2" (12.7mm) CertainTeed TypeC gypsum board.2. The first layer of CertainTeed Type Cgypsum board is installed parallel to theI, C-H, or C-T studs with 1" (25mm) No. 6Type S screws at 12" (300mm) o.c. aroundthe perimeter and 24" (610mm) o.c. acrossthe field.3. The second layer is also installed parallelto the I, C-H, or C-T studs with thejoints off-set from the first layer by 24"(610mm). The panel is attached with1-5/8" (41mm) No. 6 Type S screws 12"(300mm) o.c. around the perimeter and24" (610mm) o.c. across the field.4. The face layer is applied perpendicularto the I, C-H, or C-T studs with 2" (51mm)No. 6 Type S screws at 12" (300mm) o.c.around the perimeter, at butt joints, andacross the field.5. Vertical section of duct enclosure is installedas described for the 2-Hour Rated System:Finished One Side. Board end joints ofcorner intersection for enclosure overlappedas shown in drawing on Page 18.Finishing:1/2" (12.7 mm) CertainTeed Type C or 5/8"(15.9 mm) CertainTeed or M2Tech Type Xgypsum board can be finished with paint,texture or wallpaper. High quality primer/sealer must be used prior to any type of finaldecoration. For high gloss paint and severelighting conditions, a thin skim coat of jointcompound or CertainTeed Level V Wall/Ceiling Primer Surfacer, should be appliedacross the entire surface (Level 5 Finish). Thiswill help minimize theirregularities and porosity differences betweenthe materials. Refer to GA-214, GA-216, andASTM C840 for additional finishinginstructions. Finishing is not required on shaftside of wall system.Surface Preparation of Finished Sides:No finishing is required on the shaft side ofpartitions. Joints, corners and fastener headson the opposite face side shall be finished inaccordance with ASTM C840, the GA-216, theFire Resistance Design Manual GA-600 andCertainTeed Finishing systems, or equivalentjoint compound manufacturer’s instructions.Joint compound shall comply with ASTM C475.Limitations G lasRoc Shaftwall Systems are for nonloadbearing partitions and ceilings only. GlasRoc Shaftwall Systems shall not beexposed to sustained temperaturesexceeding 125 F (52 C). GlasRoc gypsum board should not comein direct contact with concrete, masonryor other surfaces that have a high moisturecontent. GlasRoc Shaftwall Systems are notdesigned to serve as an unlined air supplyduct. Where gypsum board is used in airhandling systems, the board temperatureshall be maintained above the air streamdew point temperature but not higher than125 F (52 C). Caulk with Green Glue NoiseproofingSealant, or equivalent to seal perimetersand penetrations to minimize air noises anddust associated with air movement.GlasRoc Shaftliner Type X Gypsum Boards for Gypsum Shaftwall Systems Call Toll Free 1-800-446-5284 www.certainteed.com5
Working with the ProductProduct SpecificationsCOMPONENT SPECIFICATIONSHelpful Hints1. Use a fastening plate to secure theJ-Track whenever fasteners are closerthan 4” (100 mm) to the edge. Settingthe plate at the time of concreteconstruction will avoid spalling bymechanical fasteners.2. Pre-cut I, C-H or C-T Studs 5/8" (16 mm)less than the height of the opening.3. Pre-cut 1" (25.4 mm) GlasRoc Shaftlinerboards 1" (25 mm) less than the height ofthe opening.4. In structural steel frame construction,install J-Track sections before applyingspray-on fireproofing.5. Items to be anchored to the wall(cabinets, sinks, handrails, etc.) shouldbe fastened to the I, C-H or C-T Studs orto plates secured behind or between thelayers of CertainTeed or M2Tech TypeX or Type C.6. Joint compounds should be appliedat ambient temperatures above 50ºF(10ºC). Provide adequate ventilation to“drive-off” excess moisture.7. For acoustic sealant and prevention of airleakage, use a bead of flexible caulking,such as Green Glue NoiseproofingSealant, at the perimeter of each wallunder the face layer and under the 2-1/2"(64 mm) flange of J-Track for shaftwallfinished on one side to minimize whistlingand dirt accumulation.8. Use Type S screws for 25 ga steelframing. Use Type S-12 screws for 20 gaor heavier steel framing.Type CStandardsType CType XShaftlinerASTM C1396,ASTM C1658ASTM C1396 / CAN/CSA-A82.27C 645Steel FramingC 645C 645Thickness1/2" (12.7 mm)5/8" (15.9 mm)5/8" (15.9 mm)1" (25.4 mm)25 ga**20 ga**19 ga** Width/Size*4' (1220 mm)4' (1220 mm)4' (1220 mm)2' (610 mm)2-1/2", 4"2-1/2", 4", 6"4", 6"Lengths*8', 9', 10', 12'8', 12'8', 9', 10', 12'8', 10', 12'Approx.Weight1.8 psf(8.8 kg/m2)2.3 psf(11.2 kg/m2)2.3 psf(11.2 kg/m2)4.0 psf(19.5 kg/m2)TaperedTaperedTaperedDouble BeveledEdges* 2-1/2" 64 mm4" 102 mm6" 152 mm8' 2440 mm9' 2740 mm10' 3050 mm12' 3660 mm** 25 ga: .0188" 0.478 mm20 ga: .0329" 0.836 mm19 ga: .0400" 1.02 mmCertainTeed Gypsum certifies that the gypsum board products described herein meet or exceed listed ASTM standardspecifications. All products are not available in all geographic areas. Consult local building codes for regulations inyour area. For further information, consult a CertainTeed sales representative.SURFACE BURNINGCertainTeed Type Cwith M2Tech CertainTeed Type Xwith M2Tech GlasRoc ShaftlinerType X0/5 Class A0/5 Class A0/10 Class A5/55/50/20ASTM E84 FlameSpread/SmokeDevelopedCAN/ULC-S102Flame Spread/SmokeDevelopedTechnical ReferencesFor additional information on application and finishing consult: ICC International Codes UL/cUL U417, U428, U429, U469, U529, V433, V470, W409, W437, W453 ULC W446 UL ER3660-02 Gypsum Association Publications GA-214, GA-216, and GA-600 ASTM C475, C514, C645, C734, C840, C1002, C1047, C1396, C1658, E84, E119, CAN/CSA A82.27, CAN/ULC-S101, CAN/ULC-S102, CAN/ULC-S114 NBCCHandling and StorageGlasRoc gypsum boards should be stacked flat on a smooth, level surface, not directly on theground. When spacers are used, position them closely enough together to minimize warpage. Careshould be taken to prevent damage to edges and corners. Always keep GlasRoc , CertainTeed and M2Tech gypsum board dry prior to installation. CertainTeed assumes no responsibility forconsequential damages that may result from the presence of standing water.6
Vertical Systems1 and 2 hour Fire Resistance RatingFIRE RESISTANCE RATED SYSTEM DESIGNS FINISHED ONE SIDE1" [25.4mm] GlasRoc Shaftliner Type X24" [610mm]I, C-H or C-T Stud24" [610mm] o.c. max1 HRVERTICAL SHAFTWALL SYSTEMFINISHED ONE SIDEFIRE TESTUL U417/ULC W4465/8"[15.9mm] CertainTeed or M2Tech Type X(Applied Vertically)1" [25.4mm] GlasRoc Shaftliner gypsum boards are inserted between 2-1/2" [64mm],4" [102mm] or 6" [152mm] I, C-H, or C-T Studs. A single layer of 5/8" [15.9mm]CertainTeed or M2Tech Type X gypsum board is applied vertically, parallel to framing,on open stud-face side with 1" [25 mm] Type S screws spaced 12" [300 mm] on center.Exposed joints and screwheads are to be finished with CertainTeed Finishing Systemunless otherwise specified. (Non-Loadbearing)1" [25.4mm] GlasRoc Shaftliner Type X24" [610mm]I, C-H or C-T Stud24" [610mm] o.c. maxSOUND REPORTNGC 2006036 STC 41 withCertainTeed Sustainable Insulation;OL 14-0504 STC 50 with resilientchannel and CertainTeedSustainable Insulation or equivalentTHICKNESS3-1/8" [80mm]APPROX. WT.6.5 psf [32 kg/m2]2 HRVERTICAL SHAFTWALL SYSTEMFINISHED ONE SIDE1/2" [12.7mm] CertainTeed Type Cor 5/8" [15.9mm] CertainTeed or M2Tech Type X(Applied Vertically or Horizontally)1/2" [12.7mm] CertainTeed Type C or 5/8" [15.9mm]CertainTeed or M2Tech Type X(Applied Horizontally or Vertically)1" [25.4mm] GlasRoc Shaftliner gypsum boards are inserted between 2-1/2" [64 mm], 4"[102 mm] or 6" [152 mm] I, C-H or C-T Studs. Two layers of 1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm] CertainTeed or M2Tech Type X gypsum board are applied toone side, with the base layer applied vertically or horizontally to the open-stud-face offraming studs with 1" [25 mm] Type S buglehead screws spaced 24" [600 mm] o.c. Thesecond layer is placed vertically or horizontally (opposite of base layer) over the baselayer and fastened using 1-5/8" [41 mm] No. 6 Type S screws spaced 12" [300 mm] oncenter. Exposed joints and screwheads are to be finished with CertainTeed Finishingsystem, or equivalent, unless otherwise specified. (Non-Loadbearing)FIRE TESTUL U417/ULC W446SOUND REPORTOL 14-0502 STC 54 with 5/8" (15.9mm) CertainTeed or M2Tech TypeX, resilient channel and CertainTeedSustainable Insulation or equivalentTHICKNESS3-3/4" [95mm]APPROX. WT.9 psf [44 kg/m2]GlasRoc Shaftliner Type X Gypsum Boards for Gypsum Shaftwall Systems Call Toll Free 1-800-446-5284 www.certainteed.com7
Vertical Systems1 and 2 hour Fire Resistance RatingFIRE RESISTANCE RATED SYSTEM DESIGNS FINISHED BOTH SIDES1" [25.4mm]GlasRoc Shaftliner Type X24" [610mm]2 HRI, C-H or C-T Stud24" [610mm] o.c. maxVERTICAL SHAFTWALL SYSTEMFINISHED BOTH SIDESFIRE TESTUL U417/ULC W446SOUND REPORTOL 14-0502 STC 54with resilient channeland CertainTeedSustainable Insulation or equivalent1/2" [12.7mm] CertainTeed Type C or 5/8"[15.9mm] CertainTeed or M2Tech Type X1" [25.4 mm] GlasRoc Shaftliner gypsum boards are inserted between 2-1/2" [64 mm], 4"[102 mm] or 6" [152 mm] I, C-H or C-T Studs. A single layer of 1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm] CertainTeed or M2Tech Type X gypsum board is applied verticallyon both sides, parallel to framing with 1" [25 mm] Type S screws spaced 12" [300 mm]o.c. Joints are staggered or offset. Exposed joints and screwheads are to be finished withCertainTeed Finishing System unless otherwise specified. (Non-Loadbearing)THICKNESS3-3/4" [95mm]APPROX. WT.9 psf [44 kg/m2]SOUND CONTROL SYSTEM FINISHED ONE SIDEI, C-H or C-T Stud 24"[610mm] o.c. max1" [25.4mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type X (Applied Horizontally)with 1" [25 mm] Type S Screws 24"[600 mm] o.c.24" [610mm]CertainTeed Sustainable Insulation Resilient ChannelsInstalled Horizontally24" [610mm] o.c.FINISHED ONE SIDEFIRE TESTUL U417/ULC W4461/2" [12.7mm] CertainTeed Type C or 5/8"[15.9 mm] CertainTeed or M2Tech Type X(Applied Vertically) with 1-5/8" [41mm] TypeS Screws 12" [300 mm] o.c.A two-hour rated finished-one-side construction, the base and face layers of 1/2" [12.7mm]CertainTeed Type C or 5/8" [15.9mm] CertainTeed or M2Tech Type X gypsum board areapplied over 25 gauge resilient furring channels installed horizontally at 24" [610mm] o.c.fastened with 3/8" [10mm] Type S panhead screws. The cavity of the partition is filled withCertainTeed Sustainable Insulation or equivalent. Caulking is applied under top and bottomtracks and around both face perimeters. Exposed joints are to be finished with CertainTeed Finishing System unless otherwise specified. (Non-Loadbearing)82 HRVERTICAL SHAFTWALL SYSTEMSOUND CONTROLSOUND REPORTOL 14-0502 STC 54with CertainTeedSustainable Insulation or equivalentTHICKNESS5-1/2" [140 mm]APPROX. WT.9 psf [44 kg/m2]
Vertical Assembly Details SECTION DETAILSI Stud DetailC-T Stud 4mm]2-1/2", 4", 6"[64mm, 102mm, 152mm]1-1/2"[38mm]1"[25.4mm]2-1/2", 4", 6"[64mm, 102mm, 152mm]1"[25.4mm]2-1/2", 4", 6"[64mm, 102mm, 152mm]C-H Stud Detail2-1/2" 4", 6"[64mm, 102mm, 152mm]2-1/2", 4", 6"[64mm, 102mm, 152mm]J-L Corner DetailJ-Track Detail3/4"1"[25.4mm]2-1/2", 4, 6"[51mm, 102mm, 152mm][19mm][19mm]DETAILS- FINISHED ONE SIDE1"[25.4mm]OUTSIDE CORNERCertainTeed cornerreinforcementfinishing or equivalentC-T Stud DetailCorner SideJ-TrackI Stud DetailShaft Side1-1/2"[38mm]J-Track with Panhead ScrewsTrack to Track(L Corner Optional)1"[25mm]2-1/4"[57mm]1/2" [12.7mm] CertainTeed Type C or 5/8" [15.9mm]CertainTeed or M2Tech Type X2-1/2", 4, 6"[51mm, 102mm, 152mm]INSIDE AND OUTSIDE CORNER1/2" [12.7mm] CertainTeed Type C or 5/8" [15.9mm]CertainTeed or M2Tech Type X1" [25.4mm]GlasRoc ShaftlinerType X1" [25.4mm] GlasRoc Shaftliner Type XJ-Track[51mm, 102mm, 152mm]J Track DetailJ-L Corner DetailTYPICAL START/END OF WALL1/2" [12.7mm] CertainTeed Type C or 5/8" [15.9mm]CertainTeed or M2Tech Type XShaft SideI, C-H or C-T Stud2-1/2", 4,o.c.6" max.24" [610mm]2-1/2", 4, 6"[51mm, 102mm, 152mm]1" [25.4mm]GlasRoc Shaftliner Type XCertainTeed cornerreinforcementfinishing or equivalent1"[25mm]2-1/2", 4, 6"[51mm, 102mm, 152mm]3/4" 3/4"[19mm][19mm]1-5/8"[41mm]1"[25.4mm]2-1/2", 4, 6"[51mm, 102mm, 152mm]1-1/2"[38mm]ALTERNATE END OF WALL SECTIONFlexible CaulkJ-TrackFlexible CaulkFlexible Caulk1" [25.4mm] GlasRoc Shaftliner Type X1/2" [12.7mm] CertainTeed TypeC or 5/8" [15.9mm] CertainTeed or M2Tech Type XJ-TrackFlexible CaulkGlasRoc Shaftliner Type X Gypsum Boards for Gypsum Shaftwall Systems Call Toll Free 1-800-446-5284 www.certainteed.com9
Vertical Assembly DetailsWALL INTERSECTION ON SHAFTLINER SIDESEPARATION WALL INTERSECTION ON FINISHED SIDE5/8" [15.9 mm]CertainTeed or M2Tech Type X1" [25.4 mm]GlasRoc Shaftliner Type XFlexible Caulk1" [25 mm]GlasRoc Shaftliner Type XJ-Track1"[25 mm]GlasRoc Shaftliner Type XScrews24" [600 mm] o.c.1/2" [12.7 mm] CertainTeed TypeC or 5/8" [15.9 mm] CertainTeed or M2Tech Type X5/8" [15.9 mm]CertainTeed orM2Tech Type XFlexible Caulk1" [25.4 mm]GlasRoc Shaftliner Type XCertainTeed corner reinforcementfinishing or equivalentDETAILS - FINISHED BOTH SIDESABUTMENT TO MASONRY1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orCertainTeed Type XWALL INTERSECTION ON CAVITY SIDE1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type X1/2" [12.7 mm] CertainTeed TypeC or 5/8" [15.9 mm] CertainTeed or M2Tech Type X1" [25.4 mm] GlasRoc Shaftliner Type X1" [25.4 mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type X1/2" [12.7 mm] CertainTeed TypeC or 5/8" [15.9 mm] CertainTeed or M2Tech Type XFlexible Caulk1" [25.4 mm]GlasRoc Shaftliner Type X1/2" [12.7 mm]CertainTeed Type C or 5/8"[15.9 mm]CertainTeed orM2Tech Type X1" [25 mm] Screws12" [300 mm] o.c.INSIDE AND OUTSIDE CORNER1" [25.4 mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed TypeC or 5/8" [15.9 mm] CertainTeed or M2Tech Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed or M2Tech Type X1" [25.4 mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type X1”[25.4 mm]GlasRoc Shaftliner Type X1" [25 mm] Screws24" [600 mm] o.c.1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed or M2Tech Type X10
Additional DetailsSHAFTWALL TO BEAMSHAFTWALL OFFSET FROM BEAM1-1/2" (38 mm) Min.Beam FireproofingSpray on Fireproofing8" (200 mm) Max.J-TrackJ Track Set To BeamBefore Beam FireproofingFasteners 24" (600 mm) o.c.Panhead S-12 Screws24" (600 mm) o.c.Suitable Fasteners24" (600 mm) o.c.1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type X1" [25.4mm]GlasRoc Shaftliner Type X14 ga. Steel Plate1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type X1" [25.4 mm] GlasRoc Shaftliner Type XSHAFTWALL OFFSET FROM DECK1-1/2" (38 mm)Min.3”8" (200 mm)Max.J-TrackFasteners 24"(600 mm) o.c.14 ga. Steel PlatePanhead S-12 Screws24" (600 mm) o.c.1" [25.4mm]GlasRoc Shaftliner Type X1" [25.4mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type XTOP AT BEAM AND FLOOR BYPASSSpray on FireproofingSHAFT CANT1" [25.4mm]GlasRoc Shaftliner Type XCant Strips Screwed toStuds to Prevent LedgesGreater Than 2" (50 mm)1" [25.4 mm] GlasRoc Shaftliner Type XSuitable Fasteners24" (600 mm) o.c.1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type XJ-Track1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type XFlexible CaulkFlexible Caulk1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type XJ-Track1”[25.4 mm]GlasRoc Shaftliner Type XFlexible Caulk1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type XGlasRoc Shaftliner Type X Gypsum Boards for Gypsum Shaftwall Systems Call Toll Free 1-800-446-5284 www.certainteed.com11
Additional DetailsCORNER COLUMN BYPASSBYPASS OF LARGE COLUMNSJ-Track1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type XSet I, C-H or C-T Studs BeforeFireproofing Where SpacingBetween J-Tracks Exceeds 24" (610 mm)J-Track1" [25.4 mm] GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type XJ-TrackColumn FireproofingColumn Fireproofing1" [25.4 mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type XHAND RAIL ATTACHMENT DETAILS1" [25.4 mm] GlasRoc Shaftliner Type X1" [25.4 mm] GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type XAttach Through Face LayerInto Stud or use Min.6"x26" (150 mm x 660 mm)20 ga. Steel Strip6"x6" (150 mm x 150 mm)16 ga. Steel PlateNo. 10 or Larger ScrewsHeavyMedium1" [25.4 mm] GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type XAttach Through Face Layer Into StudNo. 10 or Larger ScrewsLight12
Accessory DetailsSHAFTWALL ELEVATOR ELECTRICAL CONTROL LAYOUTI, C-H or C-T Stud1" [25.4 mm] GlasRoc Shaftliner Type XJ-Track1/2" [12.7 mm] CertainTeed Type Cor 5/8" [15.9 mm] CertainTeed orM2Tech Type XAAElevator DoorFrameAnnunciationPanelFiremanSwitchBBCall Box25 ga. x 3" (75 mm) x 14" (350 mm)Sheet Steel1" [25.4 mm]GlasRoc Shaftliner Type X25 ga. x 3" (75 mm) x 28" (700 mm)Sheet Steel4" (102 mm) StudSealant3/4" (19 mm) ChannelShaftwall Fireman Switchand Annunciator Panel(Section A-A)Annunciator PanelNOTE: Stud Size VariesAccording to ApplicationFiremanSwitch1" [25.4 mm]GlasRoc Shaftliner Type X1/2" [12.7 mm] CertainTeed Type C or 5/8" [15.9 mm]CertainTeed or M2Tech Type XJ-TrackControl Joi
CertainTeed Type C or 5/8" (15.9 mm) CertainTeed or M2Tech Type X gypsum boards. EITHER I-STUD, C-H STUD OR C-T STUDS MAY BE USED IN CONJUNCTION WITH GlasRoc shaftwall . such as Green Glue Noiseproofing Sealant, under the top and bottom tracks and around the exterior face perim
Shaftliner Type X GlasRoc Shaftliner is a paperless mold and moisture resistant gypsum board combining reinforcing glass mats and a specially formulated fire and moisture resistive, non combustible core. GlasRoc Shaftliner offers: Long term protection (12 months) to weather exposure. A superior water resistant surface that does not .
Continue wall as needed by placing H-Studs between the proceeding panels every 24" (610 mm) for the length of the wall and enclose the end panels with vertical C-Track. Cap the wall assembly before continuing higher using C-Track fastened to the H-Studs on alternate sides with 3/8 (10 mm)" Type S screws. A second C-Track for the next row of
DensGlass Shaftliner is a unique area separation wall panel and a key component of an Area Separation Wall assembly for use in multi-family townhouses. DensGlass Shaftliner consists of a water-resistant, noncombustible gypsum core (as defined and tested in accordance with ASTM E136 or
shaftwall assemblies. C-T studs and gypsum shaftliner panels are friction fit between the top and bottom J-Tabbed track. J-Tabbed tracks have unequal legs with the longer leg (available in 2-1/4" and 3") installed toward the shaft. The leg provides a backstop for easy installation of the shaftliner. Three-inch leg track is typically used as
GlasRoc Shaftliner is used in conjunction with CertainTeed gypsum board products in Area Separation Firewalls. Area Separation Firewalls are solid type separation walls assembled using 1" (25.4 mm) GlasRoc Shaftliner gypsum board, metal framing and 1/2" (12.7 mm) M2Tech Moisture and Mold Resistant Board or CertainTeed Regular or
Gridstone Ceiling Boards, Gypsum Sheathing, Fire-Shield Shaftliner, Durasan Prefinished Gypsum Board, Exterior Soffit Board, and Joint Treatment products. Our concentration isn’t on building products alone, however. At the National Gypsum Research and Testing Center, we develop complete construction sys-tems
(610 mm) o.c. starting 3” (76 mm) from top and bottom. (5/8” (15.9 mm) DensArmor Plus Fireguard gypsum panels may be used in lieu of 1/2” (12.7 mm) ToughRock Fireguard C gypsum board, (if desired.) The horiz
the welfarist objective assumed in modern Mirrleesian theory. In normative terms, the shift from the classical bene–t-based view to the dominant modern approach, which pursues so-called "endowment taxation," is quite substantial. Under the modern approach, an individual s income-earning ability is taken as a given, and as ability makes it .
