Customer Guide To Ground Engaging Tools
ONUDN DE NE GNAGGA IGNI GN GT OT OO LOSL SG RG OR UCustomer Guide to Ground Engaging ToolsCaterpillar’s Ground Engaging Tools (GET) are designed to Increase machine productivity by matching GET products to a machineand its applications Protect structural or more expensive machine componentsfrom wear.For the best performance, always use Cat GET.This booklet contains Specifications, Index of measures, Selector guidesfor the following Cat machines Loaders Excavators Backhoe Loaders Motor Graders Tractors
LoadersBucket Maintenance TipsNever operate a bare bucket – The baseedge is an integral part of the bucket anddirectly affects its structural strength.Replacing the base edge generallyremoves machines from productive useduring the repair period. Extension ofbase edge life through wear plates is aneconomic method of increasing machineup time. If the application does not requirebucket teeth or teeth with bolt-on edgesegments, then use flat bolt-on or weld-onhalf-arrow edges.Replace worn base edges – Base edgesshould be replaced before they wear thinenough to fail. A failure means unscheduleddowntime and a chance for structuralbucket damage. If possible, use eitherCorner Guard System base edges orCaterpillar Rock Bucket edges with predrilled bolt holes. Both permit use ofall available options.Rotate bucket tips and bolt-on edgesegments – Rotate tips from ends to thecenter and vice versa, also turning themover. Rotating and turning tips will extendwear life, distribute wear, and maintain tipsharpness. Rotating end segments towardthe center at turn time will distribute wearamong segments.Run bolt-on edges, segments, and tipsto their full service life but not beyond –Exceeding wear life could cause wear tobucket structural members and result inhigher repair costs.Maintain the bucket positioner inproper adjustment – This will keepthe bucket level to the ground andhelp you eliminate uneven wear onthe bottom. Maintaining properbucket positioning will generallyplace tips at the angle for optimumpenetration.Check the lubrication daily onthe bucket linkage pins –On machines not equipped withsealed linkage pins, considerinstalling them. They will extendlubrication intervals and reducemaintenance time. See lubricationinstructions in your machinemaintenance guide.Minimize bucket contact withthe ground – Lower the bucketto the ground only when you areready to enter the stock-pile.Unnecessary contacts with theground wear the bucket bottom andincrease GET consumption.BaseCorner Guard SystemRock (Spade)A straight edge allows for greater breakout force,give greater strength and generate more dumpclearance.A spade edge provides more penetration andincreases the capacity of the bucket.Bucket SystemsPenetration abilityImpact resistanceKeysWear life/Abrasion protectionMaintenance TipsSmooth floor maintenanceNew Product Option!Important NoteBolt-on cuttingedges2Bolt-on two-strapadaptersBolt-on two-strapadapters with edgesegments
GROUND ENGAGING TOOLSBucket SystemsCorner Guard System Edges – Available for General Purposeand Multi-Purpose buckets. Depending on job requirements,Corner Guard System base edges can be equipped with eitherbolt-on edges, bolt-on teeth, or bolt-on teeth with bolt-onedge segments.Rock Bucket Edges – Available with a spade shape (950 thru994) or with a straight edge (988 thru 994-size buckets). Spadeedges also come with bolt holes to accept either bolt-on edges(except 994) or bolt-on edge segments between teeth.Corner Guard SystemRock Bucket System2-StrapWeld-onAdapterBase EdgeWear PlateBolt-onEdges2-StrapBolt-onAdapterReversible EdgeSegmentTipBolt-onWear PlateEdge SegmentCorner Adapterand ToothCutting edges(bolt-on or weld-on)FlushmountadaptersReversibleEnd BitsBottom-StrapadaptersBolt-on EdgesTwo-strapadaptersBottom-strapadapters withedge segmentsTwo-strap adapterswith edge segmentsHeavy Duty system3
Corner Guard Bolt-on Cutting EdgesTwo-Bolt Corner GuardWhen penetration is not a problem, such as clean-up work or stockpiling,use the Corner Guard cutting edges. This system: increases base edge life up to 5 times over unprotected base edge is quick and easy to replace increases bucket capacity provides smooth floor maintenance capability is made from DH-2 steel alloy, through hardened to 430-520 Brinell.Standard cutting edges can be “propellered” to present a second wear life.Available for the full range of Wheel Loader (except 990-994).Heavy Duty cutting edges are also reversible. This thicker option provides at least 50%more wear material and a better cost per hour. Available for 950B/E/F, 966C/D/E/F,980C/F/G.Center EdgeEnd BitAbrasion-Resistant MaterialThe Abrasion Resistant Material (ARM) cutting edges are available for Corner GuardSystem fitting General Purpose and Multi-Purpose buckets. Very hard abrasion resistantparticles have been added to protect critical wear areas (under the leading edge, in front ofbolt heads, and under the bucket’s front corners).Recommended for low to moderate impact applications, it is ideal where sand,gravel and other abrasive materials create high wear rates.These edges are not reversible but will give you three to five times the wear life of standardbolt-on cutting edges and are very cost effective in stockpile application. Available for thefull range of Cat loader (except 990-994).Corner Protectors for Bolt-on Cutting EdgesThe corner protectors are designed to protect the bucket corners from wear when bolt-oncutting edges are used. This will ensure that bucket corners can accept bolt-on adapterswhen necessary. They will also provide a sharper edge than the bucket corner. This willresult in better penetration in stockpile, bank loading, and light excavation applications withcorner guard system buckets.Corner Guard System Corner Protectors4Machine ModelAdapter SizeRight HandLeft Hand916, 918, 924, 926, 928, 938939, 943, 953, IT18, IT24,IT26, IT28, IT38J250173-5422173-5423950, 960, 962, 963, 966CJ300173-5424173-5425966D, G, 970, 972G, 980J350173-5426173-5427980G, 988GJ400, J460173-5428173-5429
GROUND ENGAGING TOOLSStandard DH-2EdgesMachine ModelStyleCenterEnd BitsHeavy DutyCenterDimensionStandard CenterEdgesARM EdgesEnd BitsCenterRighthand–End BitsLefthandRighthand––914G, IT14GCGS9W86204T2914928GCGS8E45674T8091135-6728 135-6729 9W3481Width LengthLefthandmmmm–2549W3482280DimensionStandard End BitsThicknessWidth LengthmmWidth ARMEdges*Thick- CenterEnd 34225245290936F, 938F,GCGS107-37464T8091107-3298 107-3299 9W34819W348228011802516034225245290916, 918F, IT18F,924F, IT24F, IT12, IT26,926, 928F, IT28F, 953CGS1U02954T80919W3486 9W34879W34819W348228010252516034225245290920, IT28F, 928F, 930CGS1U06074T80919W3483 9W34839W34819W348228010442516034225245290936, 938F,CGS1U02924T80919W3484 9W34859W34819W348228011622516034225245290938F, 938GCGS110-47114T8091123-9195 123-9196 9W34819W348228012012516034225245290944, 950ACGS1U241436010443017049630950G, 962GCGS139-92304T8101 135-9666 132-1033 138-0672 138-0673 9W34899W348836012833017049630360365944, 950ACGS1U24124T8101 132-1031 132-1033 9W3490 9W34919W34889W348936011483017049630245365950BEF, 960FCGS1U06014T8101 132-1034 132-1033 9W3492 9W34939W34889W3489360121030170496302453653804T8101 132-1030 132-1033966CCGS1U24063G6395 100-4045 100-4044 9W3479 9W3480 123-0336 123-033736012313020051035282960F, 966DEFG, 970F, 972GCGS1U05933G6395 100-4046 100-4044 9W3477 9W3478 123-0336 123-033736013193020051035282380966DE, 960F, 970FCGS1U19093G6395 135-9533 100-4004 107-3282 107-3283 123-0336 123-033736012603020051035282380972G, 970F, 966GCGS100-66683G6395 135-9410 100-4044 107-3286 107-3287 123-0336 21135980C3-PC.4T65894T6590 107-8574 107-857540616663540685935980C3-PC.4T65944T6592 107-8578 1U1464 132-1026 132-1027 9W34699W34719W34702807882528081925245245945, 950A3-PC.1U14701U1460 132-1028 132-1029 0762123-0335 61 109-9230 100-4043 109-9214 109-9214 123-0334 109-2697 109-2697 123-0334 761 183-5325132-1070 132-1069 123-0334 123-0335406158735265556404064101U0761 100-4047 100-40436Y32716Y3271944, 950A3-PC.1U14701U1469 132-1028 132-1029 9W34669W34679W34683609913084136030245245920, 930, 944, 9503-PC.1U14651U14649W3469 U14761U14759W3472 9W34729W34739W347436014043075636030245245* ARM edges and end bits have the same Length and Thickness as the standard edges and end bits.Bolt-on Cutting Edges for Rock BucketsUsed across the entire rock bucket base edge, bolt-on cutting edges: can extend the base edge life up to five times maintain smooth, clean work surface increase bucket capacity are reversible to provide a second wear life are ideal for abrasive conditions were penetration is not a problem are made from DH-2 steel alloy, through hardened to 430-520 Brinell.Heavy Duty options are thicker for extended wear life and lower cost per hour.Available for 980 - 9925
Bolt-on Edge SegmentsBolted directly to the bottom of the base edge between adapters, these segments: increase bucket capacity maintain smoother work surface protect base edge between teeth, eliminating scalloping increase base edge life up to 5 times are hardened to 430-520 Brinell.Standard segments are reversible. Available for all sizes of Cat loaders.Half-Arrow SegmentHeavy-DutyStandardHeavy-Duty – this thicker option provides at least 50% more wear material anda better cost per hour. Available for large wheel loaders, from the 980 thru 994.Half-Arrow segments are designed to: stay sharper and enhance protection of the base edge's front and bevel combat scalloping of the base edge between adapters combat scalloping of the segment match bottom strap thickness of shouldered adapters available for large wheel loaders, from the 966G thru 994.Edge thickness70 mm64 mm51 mm51/45 mm40 mmSegment location andthicknessStandardHeavy DutyCenterRight HandLeft HandThickness4T67604T67614T676240 29650 mm/60 67760mm/75 mmCenterRight HandLeft HandThickness4T67604T67614T676240 29650 mm/60 67760 mm/75 mmCenterRight HandLeft HandThickness101-9435101-9436101-943740 mm107-3536107-3537107-353845 mm109-9080109-9081109-908245 mmCenterRight HandLeft HandThickness9W57349W57379W573035 mm107-3490107-3491107-349245 mm116-7460116-7461116-746245 mm135-9294135-9295135-929640 mm135-9544135-9545135-954640 mmCenterRIght HandLeft HandThickness* Also available for the 994. – See your Cat dealer for further details.6Half-Arrow*Adapter familyMachine ModelJ600992GJ550992/990J460988F, GJ460/J400988B/980GJ350966G, 972G
GROUND ENGAGING TOOLSBucket Base Edges without HolesSelector Guides – Recommended Base Edge Thickness by Loader Weight.Available for installation on Caterpillar Buckets and other brands of buckets.Hardened to 400-500 Brinell.LTDimensions in mmTWLPart cknessmmCaterpillar Bucketsand Conversions*kg19 - 25416, 426, 910,916, 920, 930,931, 9356350-998025 - 32936, 943, 950,953, 9639980-19 05032 - 40966, 973, 97719 050-22 68038 - 51980, 983, 98822 680-63 50051 - 64990, 99263 500-90 26634548K9913* Conversions: Corresponding sizes of other manufacturersmachines/buckets.3226638108K9914Ask your dealer for further edge ase Edge ThicknessHalf-arrow Weld-on Edges Improve bucket penetrationIncrease bucket capacity in light and loose material handlingHelp to protect the bucket structure by adding more wear material to the base edgeCan fit any bucketHardened to 400-500 BrinellCan be used as Side Cutters on excavator bucketsDimensions in mmLWW1TPart 015211134-1774W1LWT7
Heavy Duty Quarry Bucket System* for 980G, 988F, 988G, 990, 992D, 992GKey Benefits – Cat Heavy Duty Quarry Buckets offer superiorprotection, durability and performance. Specifically designed forquarry, aggregates and mining operations in high impact and/orhigh abrasion applications, these buckets are factory-modified withadditional protection.Heavy-duty Cat GET components are designed to reduce downtime and bucket-related operating cost to help you get the mostfrom your machines. Each protection item and component wascarefully chosen in response to customer requests for a bucket thatdelivers maximum strength, durability and wear life in highimpact/high abrasion conditions.1 Liner** – Adds strength and extends overall bucket life.The base edge is raised to match the liner’s height and providea smooth working surface.2 Inner Side Wear Plate – One piece inner side wear platematches thickness of outer upper side wear plate.Provides protection to lower half of inner side plate.3 Heavy Duty Adapters 992G (Heavy Duty Quarry Bucketuses Standard J700 Adapters) – Interior adapters feature newshouldered design which provides greater strength,protection and wear life. Bottom strap thickness is matchedto the thickness of the Heavy Duty Half-Arrow Segmentfor smoother material flow.4 Three Heavy Duty Tip Options offer different combination ofstrength, wear life and penetration to best fit your job needs: Heavy Duty Long Tip Heavy Duty Abrasion Tip Heavy Duty Long Life Tip Heavy Duty Penetration TipUpsized Base Edge and Adapters*StandardMachineModel980G988F, 988G988F**990992D992GHeavy Duty QuarryBase EdgeThicknessAdapterSizeBase EdgeThicknessAdapterSize45 mm50 mm50 mm63 mm63 mm70 mmJ400J460J460J550J550J60050 mm63 mm50 mm63 mm70 mm76 mmJ460J550J460J550J600J700* Base Edge and Adapters: Except for 990 buckets the base edge and adapters are upsizedfor greater strength.** High Lift5 Three Segment Options – designed to allow choices betweenmore wear material, protection, strength and penetration: Standard Flat Segment Heavy Duty Flat Segment Heavy Duty Half-Arrow Segment6 Heavy Duty Long Life (ARM) (Corner Adapters 992GHeavy Duty Quarry Bucket uses Standard J700 Adapters) –Shouldered corner adapters use Abrasion Resistant Material(ARM) to increase wear resistance. Because corner adapters aresubjected to higher wear rates, ARM is used to extend corneradapter life.* The Heavy Duty Quarry Bucket should only be used in material densitiesof 1.6 t/m3 or less due to increased bucket weight.** All Heavy Duty Quarry Bucket wear plates options including liner, canbe purchased from Cat for placement on bucket rebuilds.112;;1213178937;;;;481065
GROUND ENGAGING TOOLS7 Dual Sidebar Protectors – Sidebars are drilled to acceptdual sidebar protectors. Cat Sidebar Protectors can be stackedto cover wear patterns that extend above a single protector.Single or dual sidebar protectors can be used to match the wearconditions of the application.10 Outer Skid Plates* – Skid plates on the outer bottom areasof the bucket shield high wear areas at and just behind thebucket’s corners. They also add corner strength. Skid platesextend past the outside of the bucket side plates to protectthe side plate welds.8 Outer Upper Side Wear Plate* – Upper side wear platescombat the wear that occurs on bucket side plates in highimpact/abrasion conditions. Because wear on the upper areasof the bucket is less severe, these plates are thinner than thelower side wear plates to save weight.11 Base Edge Wear Plates* – Wear plates offer enhancedprotection to the base edge. Bolt holes accept bolt-on wearplates for complete edge protection and extended base edgelife. Base edge wear plates cover the bottom area of the baseedge not protected by segments.9 Outer Lower Side Wear Plate* – Lower side wear platesare thicker than the upper side wear plates. These thicker plateshandle the greater wear which occurs on the lower quarterof the bucket sides in tough quarry, aggregates and miningoperations.12 Heavy Duty Rear Wear Plates* – Bolt-on thicker rear wearplates extend life.* All Heavy Duty Quarry Bucket wear plates options including liner, can be purchased fromCat for placement on bucket rebuilds.13 Hinge Bracket Wear Plates* – Weld-on wear plates protectthe lower heel of the hinge bracket assembly during bucketloading for longer bracket life.Bolt-on Rear Wear PlatesMachineModelBase EdgeWear Plate992D992C992, 992BBolt-on Wear PlateMost buckets on larger wheel loaders have bolt-on rearwear plates.Certain 980G thru 994 Rock Buckets have also base edge wearplates in addition to the bolt-on rear wear plates.Ask for details from your Caterpillar dealer.990Torque in V24749K00713545bb35b2535bbAll113-034919 mm109-921535c980F, C/973All9W675035c970All9W674935c966FAll except 4725d9W674725dAll**5V72659W674725d9W674725d980G, F950F, GWasherAll6Y3573950B, ENutHardware9V57936Y3609960F, 962GBoltThickness inmmAllAll963NoteWear Plates988B966D, EHardware ReferenceBucketAssembly950, 944* Except bucket assemblies 7V1474, 7V1784, 7V6825, 5V5464, 5V6215** Except bucket assemblies 5V7352, 9V3298Also available for the 9949
ExcavatorsBucket Maintenance TipsHow to select the right bucket for the jobBottom – Inspect inside and undersidelooking for cracks in bottom either alongwelds or through plates. Cracks hereindicate structural failure. Major repairsmay be needed. Are there areas of extremewear? Bottom may be weakened by wearand subject to early failure.Replace worn edges – Edges shouldalways be replaced before the bucket isdamaged by wear or weakened throughloss of edge support.Replace worn side-cutters – Side-cuttersshould be replaced if they no longerprotect the side-plates of the bucket.Always check for loose bolts and maintainproper torque to avoid loss of side-cutter.Rotate and turn tips – A blunt tip reducesloading efficiency. Caterpillar’s tips areself-sharpening for efficient penetrationthroughout their service life. Tips seldomwear evenly, usually the ones near thebucket corners wear fastest. Byperiodically rotating outside tips to thecenter and also turning the tips over,tip life can be increased up to 50%.This method “evens out” tip wear.A bucket that is regularly loaded at anangle into the material will show unevenwear on the leading side. Rotating andturning tips or a change in loadingdirection will help equalize your tip wear.Replace worn wear plates – Look forsevere wear near the rear of plates. If theyare severely worn, cracks are likely todevelop around them. Wear plates are notpart of the basic bucket structure, but areused to protect the structure. They shouldalways be replaced before they wearthrough. If the basic structure is weakenedby wear, it may be necessary to rebuildyour bucket before installing new plates.It is always easier and less costly to installor replace wear plates before your bucketsuffers damage.Bucket choice is a key to success, and it depends mainly on the material to be worked.Is it compacted or fragmented? How abrasive? Does it require digging, handling orseparating? These variables dictate bucket design, choice of steel, component thicknessand accessories. You can be sure to find the right combination in the Cat excavatorbucket range.Utility Standard (SU). – Demolition and construction bucket handlesbricks and broken concrete, as well as trench filling, floor leveling andbank finishing.Utility Light (LU). Low cost earthmoving bucket for floor, bank andditch finishing.Excavation/Trenching (X). – Digs and loads soft to medium materialssuch as clay. Features weld on tip adapters, hardened cutting edgeand side bars.Extreme Excavation/Trenching (EX). – Digs and loads compact/abrasivematerials like earth/rock, sand/clay, sand/gravel, coal, chalk and low abrasionores. Features bigger ground engaging tools, plus abrasion resistant steel for allwear parts.Rock (Classical/Standard). – Digs and loads mixed earth/rock soilscontaining high percentage of rock or other abrasive materials.Features V-spade cutting edge, thicker base and wear surfaces.Rock Loading (RL)*. – Loads large blocks of rock and other abrasivematerials. Features longer floor plate and increased side bar curvaturefor better stability under load.Block Handling (BH)*. – Handles pre-shaped blocks of marble, granite,in quarries. Features increased tip radius, deep cut side bars for longfloor platform.Skeleton Light (SL)*. – For soft and humid soils or where separation ofmaterials, e.g., branches, peatmoss, is required.Skeleton Heavy Duty (SH)*. – As S.L., but for more demandingseparation work such as sorting rock from sand or gravel ondemolition sites.Ditch Cleaning (DC). – Wide, light bucket used mainly withlong reach configurations to clean water beds and banks.Trapezoidal (T)*. – To prepare and maintain small irrigation ditches.Features angled sides to shape ditch banks in one operation.10* Bucket available on a “Made As Ordered” (MAO) basis.See you Cat dealer for further details.
Bucket Adapters for Loaders and ExcavatorsLeft hand and right hand positions arebased on a view from the cab.Left handLeft handRight handRight handBolt-on Adapters for Front End LoadersThe Corner Guard System uses two strap bolt-on adapters with fitted tips.One-Bolt Corner Adapter Protects bucket corner for longer base edge life. Easy to install, remove and replace.Two-Bolt Corner Adapter Keeps adapter securely attached. Prevents shifting. Eliminates stress and associated breakage of inner ear of one-bolt design Keeps tip aligned during entire life Easy retrofit. Converts old buckets with new corners and simplewelding process.Center Bolt-on Two-Strap Adapter For general loader applications when you don’t need a smoothwork surface. Provides good base edge protection. Easy to install, remove and replace.CenterAdapterOne Bolt CornerAdapterEdgesSegmentTwo Bolt CornerAdapterUnitooth Tip and adapter are one integrated piece for easy installation andlower initial cost Improved penetration where breakage is not a problem Recommended for nonabrasive materials11
The offset concept available for all adaptersHow fast and easily a tooth digs depends on its offset, its position with respect tothe base edge. Offset is measured from the base edge planed to the front of the tip.The greater the offset, the more aggressively the tooth digs.Weld-On Adapter OptionsFlush Mounted, Weld-on Adaptersfor Front End Loaders, Excavatorsand BackhoesNo Offset Provides smooth bucket footprint,leaving a clean, unrutted work surface Extends tire life 15 adapter nose angleBottom Strap, Weld-on Adaptersfor Front End Loaders, Excavatorsand BackhoesEdge thicknessmmCenter AdapterRight handAdapterLeft handAdapterTip FamilyMachine Model51-643G45543G45553G4556J550990, 992C45-518E04648E04658E0466J460988, 356J350245, 980, 977, 973,970, 966DEF, 95032-388J7123——J250229, 22525-381U1304——J300235, 966C, 963,955, 95019-321U1254——J250213, 214, 211, 212,205, 206, 953, 951,943, 941, 938, 936, 930,928, 926, 916,IT38, IT28, IT1813-254T1204——J200935, 931, 910, 428,426, 416, IT14, IT12Right handAdapterLeft handAdapterTip FamilyMachine Model990, 992Edge thicknessmmCenter 58E5466J460988, 98332-451U13501U13511U1352J350224, 214B, 213B, 980,977, 973, 970, 966DEF,960, 95025-329J8929——J300224, 213, 214, 211,212, 966C, 963,955, 95025-323G0169——J250213, 214, 211, 212,205, 206, 953, 951,943, 941, 938, 936, 930,928, 926, 920, 916,IT38, IT28, IT1813-198J7525——J200935, 931, 914, 910, 438,428, 426, 416,IT14, IT12Large Offset Provides the largest offset for the mostaggressive digging Thick bottom strap provides greatestbase edge protection Easy loading and dumping becausethere is no tip or adapter on top of thecutting edge to obstruct material flow For work where there’s little concernabout abrasion and tire life 15 adapter nose angle12
GROUND ENGAGING TOOLSWeld-On Adapter Options for Front End LoadersStandard Two-strap,Weld-on AdaptersMedium Offset Provides good retention inhigh-impact work Protects the base edge well For general loading, where adapterretention is a bigger concern thantire life 15 adapter nose nterRight HandLeft4T47044T47054T470670CenterRight HandLeft Hand6I86046I86056I8606706464More Protection Shouldered to provide rear tip protection.It prevents impact which can drivethe tip forward into the pin causing pinbending or breakingMore Strength Thicker and wider strap profile to addstrength Enlarged weld-groove for easierwelding: enhances adapter retentionMore Wear Material Thicker straps add 24-40% more wearmaterial than standard adapters, morewear life and increased segment andedge protectionCenterRight HandLeft 4Heavy DutyLong ht HandLeft 86J600992C,D, 554112-2555112-2556J550992, 990CenterRight HandLeft 0554159-0555159-0556J55098851Center8G3464J460988, 983, 97751CenterRight HandLeft 7464116-7465116-7466J460988, 983, terRight HandLeft 8407125-8408125-8409J400980G45CenterRight HandLeft Right HandLeft rRight HandLeft HandTip familyHeavy DutyCenterRight HandLeft Hand64Heavy Duty and Heavy Duty Long Life(ARM) Weld-on Shouldered AdaptersStandard45* Heavy Duty adapter on the Heavy Duty Quarry Bucket.Abrasion Resistant Material (ARM)Adapter Size-up Options;;;StandardAdapter;;;;;;ARMHeavy Duty LongLife Adapter Larger bucket tips for longer wear life. Larger adapters for greater resistance to breakage. Ideal for extremely abrasive or high impactconditions. Not recommended for applications wherepenetration is a concern.The Heavy Duty long life are madewith ARM. Made of extremely hardtungsten carbide, ARM retards wear.Technical informationWelding procedure is shown in Special Instruction SEHS8811-01!You have two ways to upsize your current system: Increase the size of your tooth system Increase the size of your edge and your toothsystem.13
Side cutters for Excavator Buckets Increase bucket width and capacity Protect bucket sides Improve sidebar penetrationTwo-strap, Weld-on Adapters for ExcavatorsStandard Two-strapShouldered adapters Protects the base edge well Provides good retention inhigh-impact work 8 Nose downward angle for excavatorapplications Thicker straps for enhanced strength Shouldered to provide protection to rearof bucket tip 8 Nose downward angle for excavatorapplicationsRight hand Left I86056I8606J600Spade 375,245 Front ShovelTip 6J550245 Front Shovel105-6269105-6270J550Spade 375, 350606I65546I65556I6556J550375, 0J460375, 350235, 229, 227, 225, E300456I64046I64056I6406J400330, 325, 322, 320406I63546I63556I6356J350330A, 325, 322, 320, M318383G83543G83553G8356J350229, 225, 219, 215,E240, E300, E180J300325A, 320, M318, 317, 3153G63057T33053G63067T3306J300J300J250219, 215, E200, E180219, 215, E200, E180M315, 312, M312368E9490323G63049W1304119-3253226Y3224J225307, 446, E7025119-3204J200416 - 43619119-3205J200416-436One Piece Effective in moderate-impact applications Suitable for most soil conditionsBlade Type Effective in moderate-impact conditions Drilled to accept bolt-on combination platesCombination Blade-type side cutter with bolt-oncombination plate Transfers the wear to the less expensivecombination plate Increases bite width Suitable for moderate to light-impact conditionsMachine Model6460Strike-off Use in moderate to light-impact conditionsTooth Type For heavy impact conditions where enhancedpenetration is needed Consists of replaceable tips pinned to sidemounted adapters Adapters accept all tips available forexcavator bucketsHeavy Duty For tough digging conditions More wear material to cover more of thesidebar for enhanced sidebar and bucketside protectionNote: Part number beginning with 6I are shouldered adapter.Adapter Options for Backhoe LoadersEdge thicknessmmBucket 2025* Bottom strap** Two strap14AdaptersTip familyBolt-onedgesBucket widthmmMachine Model416, 426,428, 438bolt-onweld-on8E21848J7525*J200J2009W8215 (2)118-7110 (2)226223960.3-0.86Y3224**J2259U9665 **J200416-438446
GROUND ENGAGING TOOLSBucket Tips for Loaders and ExcavatorsWhat to consider when you're choosing tips?Bucket tips come in so many different shapesand sizes, you might think it takes an expertto pick the right one. Not so!The major factors for selecting tips can bereduced to a few simple guidelines: Wear life Penetration StrengthChoose tips that have the right balanceof these for your work and you'll getthe full return for your investment.Tips for Wheel Loader and Excavator
972g, 970f, 966g cgs 100-6668 3g6395 135-9410 100-4044 107-3286 107-3287 123-0336 123-0337 360 1400 30 200 510 35 282 380 988b 3-pc. 4t6588 406 1211 35 980c 3-pc. 4t6589 4t6590 107-8574 107-8575 406 1666 35 406 859 35 980c 3-pc. 4t6594 4t6592 107-8578 107-8577 360 1542 35 406 858 35 966c 3-p
Customer satisfaction has identified as an important influencer on customer loyalty. Further, customer trust impacted by customer satisfaction which proved that customer satisfaction is an antecedent of customer trust. Moreover, an indirect relationship between customer satisfaction and loyalty through customer trust was observed.
megger test report. pt. radius sembilan utama. inspection & certification. 086/rds-ms/ut.bp/vi/2021. 4 report of megger test. ship's name : tb. karya star 6 place of inspection : samarinda date of inspection : juni, 30 - 2021 satuan mega ohm no r-ground s-ground t-ground j-ground k-ground u-ground v-ground w-ground remarks
work/products (Beading, Candles, Carving, Food Products, Soap, Weaving, etc.) ⃝I understand that if my work contains Indigenous visual representation that it is a reflection of the Indigenous culture of my native region. ⃝To the best of my knowledge, my work/products fall within Craft Council standards and expectations with respect to
Ground Beef Round 11 32,765 255.00 - 275.00 264.32 Ground Beef Sirloin - Blended GB - Steer/Heifer/Cow Source - 10 Pound Chub Basis- Coarse & Fine Grind Blended Ground Beef 73% - Blended Ground Beef 75% 0 0 0.00 - 0.00 0.00 Blended Ground Beef 81% 0 0 0.00 - 0.00 0.00 Blended Ground Beef 85% - Blended Ground Beef
Ground Resistance Tester Models 3711 and 3731 - 6 - Description The Ground Resistance Tester, Models 3711 and 3731, measure ground rod and small grid resistance through any season, without the use of auxiliary ground rods. Clamp-on ground resistance testers are used in multi-grounded systems without disconnecting the ground under test.
This guide outlines the necessary steps to set up and use Customer Portal. The guide is divided into the following major sections: Customer Portal Preparation Make sure your organization is ready for a Customer Portal. Customer Portal Setup Configure Salesforce to allow your customers to use the Customer Portal. Setting Up Customer Portal Users
Engaging P-20W Stakeholders (PPT Presentation). Strategies for engaging P–20 stakeholders were discussed, including who is engaged and why, how stakeholders with varying backgrounds are engaged, roles and responsibilities of stakeholders, and lessons learned from engaging P–20 stakeholders. Engaging Postsecondary Stakeholders
The SE-601 is a microprocessor-based ground-fault relay for ungrounded dc systems. It provides sensitive ground-fault protection without the problems associated with nuisance tripping. Ground-fault current is sensed using an SE-GRM Series Ground-Reference Module—a resistor network that limits ground-fault current to 25 mA. The SE-601 is used
