Local Firmware - IPocket232

2y ago
10 Views
4 Downloads
454.08 KB
5 Pages
Last View : 14d ago
Last Download : 14d ago
Upload by : Annika Witter
Transcription

Local Firmware DownloadHelp GuidePerforming a local Firmware Download allows you to download the latest software version to theiPocket232 Inc.’s unit using terminal emulation software, such as HyperTerminal or Procomm Plus. First,check the software version number and date in the System Settings sub-menu. For information on thelatest software version, contact us at sales@ipocket232.com.Check the Software Version and DateNOTE: These instructions apply to HyperTerminal and Procomm Plus, but the settingsand general procedures are the same for most programs.Get the Latest Software1 Contact sales@ ipocket232.com to obtain the latest software for yourdevice. You will be sent a .ZIP file.2 Unzip the file.The .HEX file is the download file.Performing a Firmware Download1 Connect the unit to the COM port of your PC or terminal with a nullmodem cable, just as you would for local configuration.www.ipocket232.com1

2 Start the terminal program and press the CONFIGURE button on the back of theunit with a ballpoint pen or similar item. The Configuration screen appears.3 Choose System Settings from the Device Settings menu.4 Choose Firmware Download from the System Settings menu.The download confirmation message appears, as shown below.5 Type n to stop the download and return to Configuration mode, or type y to continue.Instructions to reconfigure the terminal program appear, as shown below.6 Change the communications settings to speed up the download. For HyperTerminal:1. From the File menu, choose Properties.2. In the Properties dialog box, click the Configure button.3. Change the bps to 38400, the Flow Control to Hardware, and other settings asrequired.4. Click OK.5. From the Call menu, select Disconnect, then select Call. (This resets the terminal with the new settings.) For Procomm Plus:1. From the Options menu, choose System Options Modem Connections.2. Click the Modem/Connections Properties button.3. Change the baud rate to 38400, check the Use hardware flow control button,and change other settings as required.www.ipocket232.com2

4. Click OK to close the Modem/Connections dialog box.5. Click OK to close the Setup dialog box.6 Press Enter.The Firmware Download Utility warning screen appears, as shown below.7 Choose an option from the following: Type x for a trial download. This allows you to attempt a download withoutactually burning in the new code over the old. If you do the trial procedurewithout an error, you know you are doing it correctly. Type y for a full download. This option permanently deletes the existing codeby burning the new code over it. Type n to stop the download process. The unit will reset and exitconfiguration mode.8 You are ready to send the new firmware to the iPocket232 device.www.ipocket232.com3

For HyperTerminal:1. From the Transfer menu, choose Send Text File.2. In the Files of type drop down box, select All files (*.*).3. Browse to the .HEX file you unzipped earlier, and click Open. For Procomm Plus Terminal:1. From the Data menu, choose Send File.2. Browse to the .HEX file you unzipped earlier and click Open.The download begins immediately and dots appear as bytes of code are written intothe memory. Once the download is complete you will get the Download Successfulmessage, as shown below.3 Reconfigure the baud rate to 9600 in the terminal software and press the CONFIGURE button on the iPocket232 Inc. unit to return to configuration mode.NOTE: The iPocket232 Inc. unit should retain all your previous settings. Ensure yoursettings are correct before resuming operations.Error Messages “DOWNLOAD ERRORS”: If the terminal settings are incorrect, or there is aproblem with the file, you may get an error message. For example, if hardwarehandshaking is not chosen as the method of flow control, the download will fail, asshown below. If you are performing a full download, you are prompted to beginthe download again. Contact iPocket232 Inc. for a new download file if you encounterwww.ipocket232.com4

errors again. “ERROR: no crc-check record was present!”: Cyclic Redundancy Check(CRC) is an additional method of error detection that compares a specific valuebefore and after transfer. If the CRC record is missing, then the CRC cannot beperformed and should begin again or contact iPocket232 Inc. for a new download file.www.ipocket232.com5

Performing a local Firmware Download allows you to download the latest software version to the iPocket232 Inc.’s unit using terminal emulation software, such as HyperTerminal or Procomm Plus. First, check the software version number and dat

Related Documents:

Stages of a Firmware Upgrade through Firmware Packages in Service Profiles . Cisco UCS B-Series GUI Firmware Management Guide, Release 2.2 9 Upgrading Firmware through Firmware Packages in Service Profiles Updating a Management Firmware Package. Procedure Step 1 IntheNavigationpane,clickServers.

SAS and SATA hard drive firmware Emulex, QLogic, and Brocade Fibre Channel HBA firmware Tape blade firmware HP StorageWorks MDS600 HP 3Gb SAS BL Switch Firmware Note: EVA firmware, MSA2000 firmware, and BladeSystem Interconnect Switches are not covered in t

compatibility matrix, brocade firmware upgrade procedure, brocade firmware version, brocade firmwaredownload command, brocade firmware upgrade steps, brocade firmware latest version Jun 22, 2016 — How to update the firmware on a Brocade 300

Firmware Upgrade to Cisco UCS Manager Release 3.2, on page 22 Firmware Upgrade to a Minor or a Patch Release, on page 25 Firmware Downgrades, on page 25 Firmware Management in Cisco UCS Central , on page 27 Overview Cisco UCS uses firmware obtained from and certifiedby Cisco to support the endpoints in a Cisco UCS

Updating Digital SLR Camera Firmware 4 Select Firmware version in the setup menu. 5 The current firmware version will be displayed. Highlight Update and press the 6 A firmware update dialog will be displayed. Select Yes. 7 The update will begin. Follow the on-screen instruction during the update. 8 Confirm that the update was completed successfully. 8-1.Turn the camera off and remove the .

5. Click Manual Firmware Upload. In the Firmware Upgrade screen. The Manual Firmware Upload dialog box is displayed. 6. Select the firmware file that you downloaded in step 4 and click Begin Firmware Upgrade. T

To download the latest firmware version, go to www.powerlogic.com, select Firmware Downloads Products PowerLogic Metering PM800 power meter, and then click the firmware file you want to download. NOTE: To install the firmware upgrade you will need the Download Firmware U

ASTM E 989-06 (2012), Classification for Determination of Impact Insulation Class (IIC) ASTM E 2235-04 (2012) Standard Test Method for Determination of Decay Rates for Use in Sound Insulation Test Methods Test Procedure All testing was conducted in the VT test chambers at Intertek-ATI located in York, Pennsylvania. The microphones were calibrated before conducting the tests. The airborne .