2003 VOLKSWAGEN JETTA ABS REMOVAL FOR - Autoecu

2y ago
44 Views
2 Downloads
213.40 KB
13 Pages
Last View : 2d ago
Last Download : 2m ago
Upload by : Laura Ramon
Transcription

2003VOLKSWAGEN JETTA ABS REMOVALFORABS ITTMARK 20 IE & ABS MARK 60

in engine compartment, to left of vacuum brake booster component of ABS Hydraulic Control UnitABS/EDL/ASR/ESP - Mark 601. Control module, 47-pin (screwed to hydraulic unit). Two 4.8 mm wide contacts arelocated at both ends of the connection. The wiring linking between hydraulic unit andcontrol module is routed internally.Distinguishing features of ABS ITT Mark 20 IE and the ABS/EDL ITT Mark 20 IEI - ABS - ITT Mark 20 IE

Hydraulic unit /ABS control module, removing and installingSpecial tools and equipment

VAG 1331 Torque wrench or equivalentVAG 1410 Torque wrench or equivalentVAG 1869/2 Brake pedal depressor or equivalentAdditional required information sourcesComponent location:The ABS control module is bolted together with the hydraulic unit and is located in the enginecompartment, left side.CAUTION: Brake lines in the area of the hydraulic unit should not be bent!Removing For vehicles with a coded radio, obtain code.

Disconnect battery. Disconnect connector -1- of Mass Air Flow MAF sensor from air filter tube.Remove bolts -2- at air filter -3- and move filter to left side.On vehicles with Diesel engines, remove relay panel above brake booster.Remove as much brake fluid as possible from brake fluid reservoir using a brake bleederbottle.Insert brake pedal depressor VAG 1869/2 or equivalent.Activate brake pedal booster with brake pedal depressor.Connect bleeder bottle hose to bleed screw of left front brake caliper and open bleedscrew.Close left front bleed screw. Release ABS control module connector (arrow -1-) and remove (arrow -2 -)Place plastic covering under control module and hydraulic unit. Do not use rags. Note: Do not let brake fluid enter electrical connectors.

Disconnect brake lines from hydraulic unit to brake master cylinder (arrows) and suspendwith wire.Disconnect remaining brake lines from hydraulic unit.Seal brake lines and threaded holes (arrows) using plugs from repair kit, Part No. 1 HO698 311 A. Remove bolts from bracket for hydraulic unit (arrows).Remove hydraulic unit with control module.ABS control module, removing from hydraulic unit Disconnect electrical connector for hydraulic pump motor from control module

Remove bolts (arrows) from control module and remove control module.Note: When removing the control module make sure that the hydraulic unit valvedome does not contact the control module solenoid valves.Cover the control module magnet coils with a plastic cover. Do not userags.After separating the control module and hydraulic unit use transportationprotection for the valve dome.InstallingNote: Only remove the sealing plugs on the new hydraulic unit just beforeinstalling the corresponding brake line.If the sealing plugs are removed from the hydraulic unit too early, brake fluidcan escape. It can then no longer be guaranteed that the unit is sufficientlyfilled or adequately bled.When assembling the control module and hydraulic unit, be sure that thehydraulic unit valve dome does not come in contact with the control modulesolenoid valves.Using new bolts, install control module to hydraulic unit. Do not tighten

Using new bolts, install control module to hydraulic unit. Do not tightenmore than max. 4 Nm (35 inch lbs.) .Re-connect electrical connector for hydraulic pump motor.Install ABS unit to bracket.Note: Hand-tighten bolts at first to make attaching the individual brake lines easier. After tightening brake lines, tighten hydraulic unit.Continue installation in reverse order of removal.Bleed brake systemEnter radio code.Code control module.Tightening Torques:Control module to hydraulic unit max.4 Nm (35 inch lbs,)Hydraulic unit to bracket8 Nm (70 inch lbs.)Nut for brake master cylinder to brake booster20 Nm (15 ft. lbs.)Brake lines at ABS unit:Thread M10 x 114 Nm (10 ft. lbs.)Thread M12 x 114 Nm (10 ft. lbs.)Nut to body20 Nm (15 ft. lbs.)Cap nut to body20 Nm (15 ft. lbs.)Control module and hydraulic unitMark 60, removing and installingSpecial tools and equipment

VAG 1331 Torque wrenchVAG 1410 Torque wrenchVAG 1869/2 Brake pedal depressorLocation:The control module is bolted to the hydraulic unit and is located on left in the enginecompartment.WARNING: Do not bend the brake lines in the area of the hydraulic unit!Removing: Request radio code on vehicles with coded radio if necessary.Disconnect battery.

Release control module connector (arrow -1-) and pull off (arrow -2-).Install brake pedal loading device VAG 1869/2.Connect bleeder bottle hose to left front brake caliper and left rear caliper bleed screw andopen bleed screws.Depress brake pedal at least 60 mm (2.36 inch) with brake pedal depressor VAG1869/2.Close left front and left rear caliper bleed screws.Do not remove brake pedal depressor VAG 1869/2 from brake pedal.Place sufficient lint-free cloths under the control module and hydraulic unit. Make sure nobrake fluid gets onto contacts.Disconnect brake lines -1- from hydraulic unit to brake master cylinder and tie upDisconnect remaining brake lines on hydraulic unit.Seal brake lines and threaded holes with plugs from repair set Part No. 1H0698311 A.Remove bolts -arrows- from hydraulic unit/control module bracket.Remove hydraulic unit with control module.Removing control module from hydraulic unit. Place the hydraulic unit with control module down on a clean flat surface.

Remove E 5 hex socket head bolt -arrows- from hydraulic pump.CAUTION: The hydraulic pump must not be separated from the hydraulic unit. Separate hydraulic unit with hydraulic pump from control module by lifting carefully offjoint -1-.When pulling off control module, make sure that the hydraulic unit valve dome doesnot contact the control module solenoid valves.Cover control module magnetic coils with a lint-free cloth.After separating control module and hydraulic unit use transportation protection forvalve dome.The contact pin -2- which is supplied as a replacement part along with the controlmodule can only be clipped in once and then it cannot be removed.InstallingNote: Only remove sealing plugs on new hydraulic unit when the correspondingbrake line is going to be installed.

brake line is going to be installed.If the sealing plugs are removed too early, brake fluid can escape, it can nolonger be guaranteed that the module is sufficiently filled or adequatelybled.When assembling the control module and hydraulic unit, be sure that the hydraulicunit valve dome does not come in contact with the control module solenoid valves. Using new bolts, install control module to hydraulic unit. Do not tightenmore than a max. 4 Nm (35 inch lbs.) .Bolt ABS module to bracket. Do not tighten bolts completely. Attaching theindividual brake lines is made easier.After tightening brake lines, tighten hydraulic unit.Further installation is carried out in the reverse sequence.Remove brake pedal depressor VAG 1869/2.Bleed brake systemEnter radio code.Code ABS control module (w/EDL) -J104-.Basic settings must be performed when replacing ABS control module(w/EDL) -J104-.Tightening Torques:Control module to hydraulic unit max.4 Nm (35 inch lbs.)Hydraulic unit to bracket8 Nm (70 inch lbs.)Nut for brake master cylinder to brake booster20 Nm (15 ft. lbs.)Brake lines at ABS module:Thread M 10 x 114 Nm (10 ft. lbs.)Thread M 12 x 114 Nm (10 ft. lbs.)Cap nut to body20 Nm (15 ft. lbs.)A.S.I. www.autoecu.com 1-866983-6688

To ship to us visit our website and printour R&R form , Complete the form andinclude it with your part then ship to ouraddress on the form.Thank You

VOLKSWAGEN JETTA ABS REMOVAL FOR ABS ITT MARK 20 IE & ABS MARK 60. in engine compartment, to left of vacuum brake booster component of ABS Hydraulic Control Unit ABS/EDL/ASR/ESP - Mark 60 1. Control module, 47-pin (screwed to hydraulic unit). Two 4.8 mm wide contacts are located at bo

Related Documents:

Instructions de montage Montageanleitung Instrucciones para el montaje 04020 01/2019. 2 . VOLKSWAGEN AMAROK 11 14 VOLKSWAGEN BEETLE 05 14 VOLKSWAGEN CC 12 14 VOLKSWAGEN EOS 06 14 VOLKSWAGEN FOX 06 12 VOLKSWAGEN CC 12 14 VOLKSWAGEN GOLF 04 14 VOLKSWAGEN JETTA 05 14 VOLKSWAGEN PASSAT 10 14

Volkswagen Group Sales India Private Limited Produced in India Subject to change without notice Issue: Aug 2011 www.volkswagen.co.in Your Volkswagen Dealer The New Jetta The New Jetta Jetta Brochure Open size: 59.4 (W) x 21 (H) cms Jetta Brochure Close size: 29.7 (W) x 21(H) cms

Total (MJ/kg) 6 362 00 PC/ABS 25x25 13.340 6 362 01/51 PC/ABS 25x40 15.272 6 362 02/52 PC/ABS 25x60 18.538 6 362 06/56 PC/ABS 40x40 20.424 6 362 07/57 PC/ABS 40x60 22.632 6 362 08/58 PC/ABS 40x80 25.162 6 362 12/62 PC/ABS 60x60 28.198 6 362 13/63 PC/ABS 60x80 33.304 6 362 17 PC/ABS 80x80 37.729 6 362 25 PC/ABS 120x80 53.802 4. DIMENSIONS .

The Jetta 03 Contents. 04 Exterior 08 Interior 14 Radio/navigation and driver's assistance systems 16 Wheels 18 Paint and Upholstery 20 Combinations 24 Technical specification 26 Technology and Dimensions 28 Volkswagen service Front cover model shown is Jetta GT with optional 18" 'Charleston' alloy wheels Model shown is Jetta GT with optional 18" 'Charleston' alloy wheels and .

Courtesy of VOLKSWAGEN UNITED STATES, INC. (3) Applies to vehicles equipped with power windows only. (4) Battery powered. (5) Manual transmission only. NOTE: Thirteenfold auxiliary relay panel is under driver's side of dash, behind lower instrument panel trim. 2000 Volkswagen Jetta GL 2000 ELECTRICAL' 'Fuses & Circuit Breakers - Golf, GTI & Jetta

The New Jetta Your Volkswagen Dealer Volkswagen Group Sales India Private Limited Produced in India Subject to change without notice Issue: October 2013 www.volkswagen.co.in The New Jetta. 2 3 Euphoria. At the turn of a key. 4 5 . Electronic Stabilisation Programme (ESP)

Subject: 2006-2007 Rabbit/R32/ GTI, 2005-2007 Jetta/Jetta Wagon, . We are writing to inform you of a service action repair that is available for your vehicle free of charge. Our records show that . Volkswagen Service & Quality .

ArtificialIntelligence: A Modern Approachby Stuart Russell and Peter Norvig, c 1995 Prentice-Hall,Inc. Section 2.3. Structure of Intelligent Agents 35 the ideal mapping for much more general situations: agents that can solve a limitless variety of tasks in a limitless variety of environments. Before we discuss how to do this, we need to look at one more requirement that an intelligent agent .