828D/840Dsl SINUMERIK Operate

2y ago
22 Views
2 Downloads
1.93 MB
36 Pages
Last View : Today
Last Download : 2m ago
Upload by : Wade Mabry
Transcription

M5701Operating mode “JOG“Brief descriptionObjective of the module:In this module you learn the different options of the operating area "Machine" in the operating mode"JOG".Description of the module:In this module the softkeys of the Sinumerik Operate, available in the manual mode (setup- and basicfunctions), will be described.Content:Operating mode "JOG"Tool, spindle and machine commands (T,S,M)Set Work offset (“Set WO”)Measure workpieceMeasuring a toolPositionFace millingSettings828D/840Dsl SINUMERIK Operate828D/840Dsl SINUMERIK OperatePage 1This document was produced for training purposes.Siemens assumes no responsibility for its contents.M570

M570M570Page 2828D/840Dsl SINUMERIK Operate

M570Operating mode JOG: DescriptionIn this module the softkeys of the Sinumerik Operate, available in the manual mode (setup andbasic functions), will be described.Operating modeJOG:STARTOperatingmode "JOG"Tool-, spindleand machinecommands(T,S,M)Set Workoffset(“Set WO”)MeasureworkpieceMeasuring atoolPositionFace millingSettingOperating modeJOG:ENDNotes828D/840Dsl SINUMERIK OperatePage 3M570

Section 2NotesOperating mode “JOG“Operation mode “JOG” is used, for setting up the machine for program runoff or if you simply want to traverse the axes on the machine: Reference point approach, i.e. calibration of the position measuring system Preparing a machine for executing a program in automatic mode, i.e.measuring tools, measuring the workpiece and, if necessary, definingthe work offsets used in the program Traversing axes, e.g. during a program interruption Positioning axes2.1Selecting the operating mode “JOG“The operating mode "JOG" can be selected as follows:Press the “JOG“ button on the machine control panel(MCP).The operating mode “JOG” opens directly.- OR Press the button “MENU SELECT“ on the machinecontrol panel.Press the VSK 1 “JOG“ in the yellow vertical softtkeybar on the right hand side of the screen to switchdirectly to the operating mode “JOG“.Then Switch to the operating area “Machine” bypressing the “MACHINE” key on the operator panelor on the keyboard or press the “MENU SELECT“key on the operator panel and the yellow HSK 1“Machine“.The following screen opens:M570Page 4828D/840Dsl SINUMERIK Operate

Operating mode “JOG“Section 2The following functions are offered in the horizontal and vertical softkey barof the operating area "Machine" ( see section 2.2 and 2.3).2.2NotesVertical softkey bars 1 and 2Display areaDescriptionThe most important G-functions are displayed in asub-window by pressing the VSK 1.1 "G functions".Available auxiliary functions are displayed in a subwindow by pressing the VSK 1.2 "Auxiliary functions" at the time of the output.By pressing the VSK 1.7 "Act. values. Machine",the coordinate system will be toggled between themachine coordinate system (MCS) and the workpiece coordinate system (WCS).Note:Refer to the machine manufacturer‘s documentation.By pressing the VSK 1.8 "Forward" on the operatorpanel (OP) the selection of additional softkeys onthe vertical softkey bar is possibleBy pressing the VSK 2.2 "All G functions" all Gfunctions will be shown.By pressing the VSK 2.6 "Zoom act. val." all actualaxes positions in the selected coordinate system aswell as the currently active feed rate and feed override of each individual axis are displayed fullscreen. In addition all active zero point offsets,transformations and the T,F,S data is being displayed in the foot line.Note:If the machine is in the sub-mode “REPOS”, thenthe in manual mode traversed path difference isalso being displayed.By pressing the VSK 2.8 "Back" on the operatorpanel (OP) the vertical softkey bar switches back tothe menu of the VSK 1.828D/840Dsl SINUMERIK OperatePage 5M570

Section 2NotesOperating mode “JOG“2.3Horizontal softkey bar 1 and 2Display areaDescriptionBy pressing the HSK 1 "T,S,M" the input screen"T,S,M" will be activated.By pressing the HSK 2 "Set WO" the input screenfor setting the work offset will be activated.By pressing the HSK 3 "Meas. workp.“ the inputmask for measuring a workpiece will be activated.By pressing the HSK 4 "Meas. tool" the function"Measure tool" will be activated and the extendedoptions "Length/Radius manual", "Length/Radiusauto", "Calibrate Probe", and “Calibrate fixed pt.”will be available in the vertical softkey bar.By pressing the HSK 5 "Position" the input screen"Target position" will be activated.By pressing the HSK 7 "Face mill." the input screen"Face milling" will be activated.By pressing the "Extend"-button on the operatorpanel (OP) more softkeys on the HSK are available.This symbol on the right of the dialogue line indicates that more options on the HSK are available.This symbol indicates that you are in the expandedsoftkey bar.By pressing the HSK 2.6 "Handwheel" the inputmask for traversing the axis in machine coordinatesystem (MCS) or workpiece coordinate system(WCS) will be available.By pressing the HSK 2.7 "Synch. Action." thescreen which shows the current synchronized actions is displayed.By pressing the HSK 2.8 "Settings" a window opensup where you can adjust the settings for manualoperation on the Sinumerik Operate.M570Page 6828D/840Dsl SINUMERIK Operate

Tool, spindle and machine commands (T,S,M)3.1Selecting the function "T,S,M"(Tool, spindle and machine commands)Section 3NotesBy pressing the HSK 1 "T,S,M" in operation area“Machine” under operation mode “JOG” the following input mask will be displayed on the screen .3.2Vertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 2 "Select tool" the tool listopens on the screen.See module M573 - "Operating area Parameter".By pressing the VSK 3 "Select work offs" a list withthe zero point offsets will be displayed.Refer to Work offset section 4 in this moduleBy pressing the VSK 8 "Back" switch back to themain screen of the Sinumerik Operate.828D/840Dsl SINUMERIK OperatePage 7M570

Section 3NotesTool, spindle and machine commands (T,S,M)3.3Parameters of "T,S,M" (Tool, spindle and machine commands)Input mask for tool-, spindle- and machine commands:Values can be entered directly in the orange marked input fields or by selecting predefined parameters with the “SELECT”-key.Alternatively the “INSERT”-button in the marked cursor field opens a selectmenu of all possible parameters, in which you can navigate with the “Tab”key as well as the blue “cursor-up”- and “cursor-down”-down buttons. Thebutton “INPUT” takes over the selected values.In order to be independently of country specific measuring units [metric/imperial] not all units are displayed in the input masks.See module M568 - "Basic operations".In this documentation the measuring units are always metric.ParameterUnitMeaningTTool name: e.g.: T12 or Cutter 7(alphanumerical).DCutting edge number of the tool.Spindle:[rpm]Spindle speed (revolutions per minute, numerical).Spindle machine functions: (Make a selection using the "SELECT"-key on the keyboard).Spindle M function: Empty fieldNo selection is made. Right(M 3)Clockwise rotation of the spindle. Left (M 4)Counter clockwise rotation of the spindle. Off (M 5)Spindle is stopped. Positioning(SPOS)Spindle positioning: Spindle is positioned tothe desired position.Manufacturer defined M-functions.By inserting the number of the function, acorresponding M-function is selected.Other M function:Refer to the machine manufacturer‘s tablefor the correlation between the meaning andthe number of the function.M570Page 8828D/840Dsl SINUMERIK Operate

Tool, spindle and machine commands (T,S,M)ParameterUnitMeaning (continuation)Section 3NotesAlternative parameter options:The actual value of the work offset refersto the machine zero point, after approaching the reference point.Work offset: None Basic referenceIn contrast a machining program refers tothe workpiece zero point. This offset is tobe entered as zero point offset. G54 G55You can select work offsets from the toollist of settable work offsets via the "Workoffset" softkey. G56 G57See module M573 - "Operating area Parameter".Alternative parameter options:Unit of measure.: none mm[mm] inch[inch]Note:The setting made here has effect on theprogramming.Machining plane: G17(XY) G18(ZX) G19(YZ)Gear stage:Specification of the gear stage(none, auto, I - V).Stop-Position:[Degree]Input of the spindle position in degrees.Note:This parameter shows up by selecting thespindle M-function.Note:With “CYCLE START“ the inserted values will be executed. The entries inthe option fields will be deleted, ready for new inputs.828D/840Dsl SINUMERIK OperatePage 9M570

Section 3NotesTool, spindle and machine commands (T,S,M)3.4Tool definition and call with the input mask "T, S, M"By pressing the HSK 1 "T, S, M" on the screenSee above in the working window open the "T, S, M" input box.The VSK 1 "Select tool" Softkey appears. Pressing this softkey will open the tool list.M570Page 10828D/840Dsl SINUMERIK Operate

Tool, spindle and machine commands (T,S,M)Press VSK 1 "New tool" Softkey to open the “Favorites” toolselection.Section 3NotesOpened by default, VSK 1 "Favorites" Softkey, you will find the mostcommon tools. By pressing on the soft keys such as "Drill", only drillingtools are offered.In our example, the first tool "Type 120 - End mill" is used.With the VSK 8 "OK" Softkey, the selected tool is created inThe name of the tool can be modified if required.For example, the tool name is edited from MILLING CUTTER with theInsert and Delete keys and changed to CUTTER D10.828D/840Dsl SINUMERIK OperatePage 11M570

Section 3NotesTool, spindle and machine commands (T,S,M)Data should now be entered if known, the tool length, the correct tool radius or diameter, and number of edges, spindle direction and possiblyexternal coolant supply can be activated.Press VSK 1 "In Manual", the tool name is now moved intothe input window of T, S, M.The tool could also have speed and direction data entered, if it is stillstored in the magazine.In this example CYCLE START is pressed to initiate the tool change.CYCLE START triggers the tool change functions withoutadditional commands such as M06.M570Page 12828D/840Dsl SINUMERIK Operate

Tool, spindle and machine commands (T,S,M)Section 3NotesThe tool should now appear in the window technology (outlined in red), thetool from the tool list with details of length, radius and edge number.To return the tool in the spindle to the magazine must only be undertakenusing "T, S, M"In the input field T enter "0".CYCLE START triggers the tool change functions withoutadditional commands such as M06.828D/840Dsl SINUMERIK OperatePage 13M570

Section 4NotesWork offset4.1Selecting the function "Work offset"By pressing the HSK 2 "Set WO" in operation area“Machine” under operation mode “JOG” the inputfield for the programming of a work offset will beopened, like displayed below.Input value:By selecting an axis you can insert a value for thezero point offset in the orange marked field (see thepicture above).The navigation through the axis-fields can be accomplished by pressing the blue “cursor-up“ and“cursor down“ keys on the keyboard.The slider on the right side of the sub window indicates that there are more axis values available, thatcan be reached by using the “cursor-down“ key.Important:The horizontal softkey 2 "Set WO" is only selectable if the workpiece coordinate system is selectedand a zero point offset (in this example G54) is active.The entered values for a zero point offset of theaxis will be accepted and displayed in the workpiece coordinate system (WCS).The difference between the original position to thenew entered value will be written to the active zeropoint offset.M570Page 14828D/840Dsl SINUMERIK Operate

Section 4Set work offset (“Set WO”)4.2NotesVertical softkey barDisplay areaDescriptionBy pressing the VSK 1 "X 0" the position of the Xaxis will be reset to zero.By pressing the VSK 2 "Y 0" the position of the Yaxis will be reset to zero.By pressing the VSK 3 "Z 0" the position of the Zaxes will be reset to zero.By pressing the VSK 4 „X Y Z 0“ the position ofthe X/Y/Z-axis will be reset to zero.By pressing the VSK 5 "Delete active WO" the zeropoint offset of all axes is set back to zero.By pressing the VSK 8 "Back" you switch back tothe main screen of the Sinumerik Operate.Note:After setting a position or deleting a zero point offset you switch backautomatically to the main screen of the Sinumerik Operate.828D/840Dsl SINUMERIK OperatePage 15M570

Section 5NotesMeasure workpiece5.1Selecting the function “Measure workpiece“In the operating area “Machine“ under the operatingmode “JOG“ press the HSK 3 "Meas. workp." toopen the “Measure workpiece“ window shown below.The reference point for programming a workpiece is always the workpiecezero. You can determine the workpiece zero on the following workpieceelements: Edges (Set edge, Align edge) Corner (Rectangular corner) Hole (1 Hole, 2 Holes, 3 Holes, 4 Holes)) Spigot (Circular spigot, rectangular spigot)The workpiece zero can be measured either manually or automatically.Measuring manually:For manual measuring their are parameters that depend upon tool type,and therefore are only available for the particular case. The tool must bemanually approached to the workpiece. You can use edge probes, sensingprobes, or dial gauges with known radii and lengths. You can also use anyother tool of which you know the radius and length. The tools used formeasuring must not be electronic probes.Measuring automatically:For automatic measurements always use electronic 3-D or mono workpiece probes. You must calibrate the electronic workpiece probes beforehand. First position the workpiece probe manually. As soon as you startthe process with the "CYCLE START" key, the workpiece probe automatically approaches the workpiece at measuring feedrate and then returns tothe starting position at rapid traverse.The machine manufacturer must first set the appropriate machine parameters (e.g. the measuring feedrate).Note: During all measurements the override of the feedrate should beset to 100%.M570Page 16828D/840Dsl SINUMERIK Operate

Section 5Measuring workpiece5.2NotesVertical softkey barDisplay areaDescriptionBy pressing the VSK 1 “Calibrate probe“ the inputmask for “Calibrate probe“ opens.By pressing the VSK 2 “Set edge“ the “Set edge“window opens.By pressing the VSK 3 “Align edge” the “Alignedge” window opens.By pressing the VSK 4 “Rectangular corner” the“Rectangular corner” window opens.By pressing the VSK 5 “1 Hole” the “1 Hole” windowopens.By pressing the VSK 6 “1 Circular spigot” the “1 Circular spigot” window opens.By pressing the VSK 8 "Back" you switch back tothe main screen of the Sinumerik Operate.5.3 Selecting the function “Calibrate probe”By pressing the HSK 3 “Meas. workp.” and the VSK5 “Calibrate probe” (in operating area “Machine”and operating mode “JOG”) the following inputscreen will be displayed.828D/840Dsl SINUMERIK OperatePage 17M570

Section 5NotesMeasuring workpiece5.4 Example of two measurement functions "Set edge" and "tapinto rectangular"As already described in Section 3, a mechanical probe to be created in thetool list and using "T, S, M" loaded into the spindle.With the VSK 1 "In Manual", the tool is transfered into theinput window of T, S, M.Additional functions of the input mask of "T, S, M"are briefly explained.The "Spindle M function", a mechanical probe isoriented for easy reading.The "Stop position" can be any angle.In addition, the offset can be activated, in which themeasured values are to be entered.M570Page 18828D/840Dsl SINUMERIK Operate

Section 5Measuring workpieceThe technology window will display the measuring tool from the tool list,with details of length and edge number.NotesNote:The part to be measured is "Set edge" on the workpiece surface with themeasurement function with 1mm oversize and is in the middle of the workpiece, measured with the measuring function "Rectangular spigot" .(This will be shown as an example in Section 5.4 and 5.5).5.4Measure workpiece zero “Set edge”The workpiece lies parallel to the coordinate system on the work table.One reference point will be measured in one of the axes (“X”, “Y”, “Z”).The following requirements must be fulfilled: Any tool can be loaded in the spindle for scratching when measuringthe workpiece zero manually. An electronic workpiece probe is loaded in the spindle and activatedwhen measuring the workpiece zero automatically.By pressing the HSK 3 “Meas. workp.” and the VSK2 “Set edge“, in the operating area “Machine“ andoperating mode “JOG“, the following screen will bedisplayed.828D/840Dsl SINUMERIK OperatePage 19M570

Section 5NotesMeasuring workpiece5.4.1 Vertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 2 “Select work offset“ a list ofthe work offsets opens.See module B573 - “Operating area Parameter“.By pressing the VSK 3 “X“ the measured values forthe X-axis will be determined.By pressing the VSK 4 “Y“ the measured values forthe Y-axis will be determined.By pressing the VSK 5 “Z“ the measured values forthe Z-axis will be determined.By pressing the VSK 7 “Set WO“ the values will beaccepted for the work offset.By pressing the VSK 8 “Back“ you switch back tothe “Measure workpiece“ main screen .5.4.2 Parameters of "Set edge"ParameterDescriptionWork offset:Alternative parameters Measure onlyThe measured values arecomputed and displayedwithout changing the coordinate system. Work offsetMeasurementdirection: X Y ZReference pointM570The selection of the axes directions “X”/”Y”/”Z” is madeby the vertical softkey bar.With the measurement direction ( or -) it is determinedwhether the workpiece will beapproached from a positiveor negative “X”- or “Y”direction.By selection of the axis direction “Z it is only possible toapproach the work piecefrom a negative Z-direction.X0, Y0, Z0Page 20828D/840Dsl SINUMERIK Operate

Section 5Measuring workpieceNotes5.5Workpiece zero measure "Rectangular spigot"The workpiece is parallel to the coordinate system on the work table andis a rectangle. About 4 measuring points of the center of the rectangle isdetermined.The following requirements must be met: Any tool can be used for scratching when loaded into the spindle forworkpiece zero manual measuring. An electronic workpiece probe when loaded into the spindle and activated will measure the workpiece zero automatically.Pressing the VSK 6 "Rectangular spigot" softkeyin the function "Meas. Workp. "(" Machine "in the" JOG ") appears on the screenthe following input mask.5.5.1 Vertical softkey bar (VSK)See page 20, Measure workpiece "Set edge".5.5.2 Parameter Measure workpiece "Rectangular spigot"The following parameters of Measure workpiece "Set edge" are also atwork measure "Rectangular spigot":[Zero offset G54, X0, Y0]828D/840Dsl SINUMERIK OperatePage 21M570

Section 6NotesMeasure tool6.1Selecting the function “Measure tool“The geometries of the machining tool must be taken into considerationwhen executing a part program. These are stored as tool offset data inthe tool list. Each time the tool is called, the control considers the tool offset data. When programming the part program, you only need to enter theworkpiece dimensions from the production drawing. After this, the controller independently calculates the individual tool path.You can determine the tool offset data, i.e. the length and radius or diameter, either manually or automatically with tool probes.By pressing the HSK 4 “Meas. tool“ in the operatingmode “JOG” under the operating area “Machine”the following window opens:Measuring a tool manuallyFor manual measurement, move the tool manually to a known referencepoint to determine the tool length and the radius or diameter. The controlthen calculates the tool offset data from the position of the tool carrier reference point and the reference point.With the measuring of the tool length either the workpiece or a fixed pointin the machines coordinate system, e.g. a load cell or a fixed point in conjunction with a distance meter, can be used as a reference point. The position of the workpiece is specified during the measurement. The position ofthe fixed point however must be announced before the measurement.With the determination of the radius or diameter the workpiece alwaysserves as the reference point.Hint:Depending on the setting in a machine data either the radius or thediameter of the tool can be measured.Note:Refer to the machine manufacturer's specifications.M570Page 22828D/840Dsl SINUMERIK Operate

Section 6Measure tool6.2NotesVertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 1 ”Length manual” the “Lengthmanual” input mask opens.By pressing the VSK 2 “Radius manual“ or rather“Diameter manual“ the input mask “Radius manual“or rather “Diameter manual“ opens.By pressing the VSK 7 ”Calibrate fixed pt.” the“Calibrate: fixed point” input mask opens.By pressing the VSK 8 “Back“ you jump back to the“Meas. tool” screen of the Sinumerik Operate.828D/840Dsl SINUMERIK OperatePage 23M570

Section 6NotesMeasure tool6.3Measure tool “Length manual”By pressing the HSK 4 “Meas. tool” and the VSK 1“Length manual“ (in the operating area “Machine“under the operating mode “JOG”) the following input mask opens.6.3.1 Vertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 2 “Tool“ the tool list opens.See module M573 - “Operating area Parameter“.By pressing the VSK 7 “Set length“ the entered values will be accepted.By pressing the VSK 8 “Back“ you jump back to the“Measure tool” screen of the Sinumerik Operate.M570Page 24828D/840Dsl SINUMERIK Operate

Section 6Measure tool6.3.2 Parameters of measure tool “Length manual“ParameterDescriptionTTool nameAlternatively you can select a toolvia the VSK 1 “Select tool”.DEdge number(1 to 9)STReplacement tool(01- 99)Ref. pointWorkpiece or Fixed pt.Z0Workpiece edgeNotes6.3.3 Procedure for Measuring tool “Length manual”1.Load the tool in the spindle you want to measure.2.In the operating mode “JOG“ press the HSK 4 “Meas.tool”.3.Press the VSK 1 “Length manual”.The “Length manual” input screen opens.4.Press the VSK 2 “Tool“.Select a tool from the “Tool list” that opens immediatelyafter pressing the softkey.5Press the VSK 1 „In manual“ to switch back with the selected tool to the “Length manual” window.4.Select the cutting edge number “D” and the number of thereplacement tool “ST”.5.Approach the workpiece in the Z direction, scratch it with arotating spindle6.Enter the set position “Z0” of the workpiece edge.7.Press the VSK "Set length" softkey.The tool length is calculated automatically and entered in the tool list.828D/840Dsl SINUMERIK OperatePage 25M570

Section 6NotesMeasure tool6.4Measure tool ”Radius manual“ or “Diameter manual”By pressing the HSK 4 “Meas. tool” and the VSK 2“Radius manual“ or “Diameter manual” (in the operating area “Machine“ and operating mode “JOG”)the following input mask opens.6.4.1 Vertical Softkey bar (VSK)Display areaDescriptionBy pressing the VSK 2 “Select tool” the tool listopens.By pressing the VSK 7 “Set diamet.“ (or “Set radius.”) all entered values will be accepted.By pressing the VSK 8 “Back“ you jump back to the“Measure tool” screen of the Sinumerik Operate“.6.4.2 Parameters measure tool “Radius manual“ or “Diametermanual”The following parameters of the function “Length manual” are used alsowith “Radius manual” and “Diameter manual”:[T, D, ST]Beside the before mentioned parameters you find the following additionalparameters in the “Radius manual” or “Diameter manual” window:M570ParameterDescriptionX0Workpiece edgeY0Workpiece edgePage 26828D/840Dsl SINUMERIK Operate

Section 6Measure tool6.4.3 Procedure for measuring the tool “radius manual” (or“diameter manual” )1.Load the tool you want to measure in the spindle.2.In the operating mode “JOG“ and operating area “Machine” pressthe HSK 4 “Meas. tool“.3.Press the VSK 2 “Radius manual“ ( or “Diameter manual“).4.Select the cutting edge number “D” and the number of the replacement tool “ST” of the tool.5.Approach the workpiece in the X- or Y-direction and performscratching with the spindle rotating in the opposite direction.6.Specify the setpoint position “X0” or “Y0” of the workpiece edge.7.Press the "Set radius" or "Set diameter" softkey.NotesThe tool radius or diameter is calculated automatically and entered inthe tool list.828D/840Dsl SINUMERIK OperatePage 27M570

Section 6NotesMeasure tool6.5Selecting the function “Calibrate fixed point”If you want to measure your tools manually, you must first determine theheight of the fixed point on the machine table with reference to the machine zero.The fixed point can be either a measuring gauge of a known height or anelectronic height gauge of known height. Place the gauge in the workingarea of the machine (e.g on the machine table) and align it relative to themachining axes.You can use any type of tool to measure the fixed point.You must enter the length and radius/diameter of the tool in the tool listbeforehand.Note:Refer to the machine manufacturer's specifications.By pressing the HSK 4 “Meas. tool” and the VSK 7“Calibrate fixed pt.“ (in the operating area “Machine“and operating mode “JOG”) the “Fixed point calibration” window opens.M570Page 28828D/840Dsl SINUMERIK Operate

Section 6Measure a toolNotes6.5.1 Vertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 7 “Calibrate“ the control calculates the fixed point height.By pressing the VSK 8 “Back“ you switch back tothe “Measure tool” window.6.5.2 Parameters of measure tool “Calibrate: fixed height”By calibrating the probe the following parameters are displayed:ParameterUnitDescriptionDZ[mm]Is the distance from the table to top of thefixed point gauge.6.5.3 procedure for tool measure “Calibrating fixed point”1.Move the calibration tool until it is approximatelyover the centre of the measuring surface of the fixedpoint gauge2.In the operating mode “JOG“ press the HSK 4“Meas. tool“.3.Press the VSK 6 “Calibrate fixed pt.”.4.Use the JOG keys in “Incremental mode, or thehandwheel to position the tool at the fixed positionheight.5.Press the “Calibrate“ softkey to calibrate the fixedpoint.828D/840Dsl SINUMERIK OperatePage 29M570

Section 7NotesPosition7.1Selecting the function “Position“In order to implement simple machining sequences, you can traverse theaxes to certain positions in manual mode.Note:The feedrate/rapid traverse override is active during traversing.By pressing the HSK 6 “Position” in the Operatingarea “Machine” and operating mode “JOG” the following input mask will be shown on the screen:7.2Vertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 5 “Rapid” the value of the setmachine data for feed rate velocity in JOG is takenover in the parameter “F” (feed).Hint:The VSK 5 “Rapid traverse” can also be pressed ifthe input field parameter “F” is not the active inputfield (highlighted in orange)By pressing the VSK 8 “Back” you switch back tothe main screen of the Sinumerik Operate.M570Page 30828D/840Dsl SINUMERIK Operate

Section 7Position7.3NotesParameters of /tooth]FeedX[mm]Target position of the selected axes[abs/inc]YNote:Several target positions can be entered.B-axis and C-axis are manufacturer specific.Follow the documentation of the machinemanufacturer.ZSP[Degree]Target angle [abs, inc]7.4. Procedure for positioning the axes1.Select the “JOG” operating mode.2.Press the HSK 6 “Position”.3.Specify the desired value for the feedrate “F”.- OR -3.Press VSK 5 "Rapid".*Rapid tr.* is displayed in the input field “F”.4.Enter the target position or the target angle for the axis oraxes to be traversed.5.Press the "CYCLE START" button on the machine controlpanel.The axis is traversed to the specified target position.Note:If target positions were specified for several axes, the axes are traversedsimultaneously.828D/840Dsl SINUMERIK OperatePage 31M570

Section 8NotesFace milling8.1Selecting the function “Face milling”You can use this cycle to face mill any workpiece. A rectangular surface isalways machined.“Measuring the workpiece" is already mentioned in section 5. The inputmask “Face milling” is described in relation to a workpiece with dimensions25x100x100 mm, with 1mm to be removed leaving a thickness of 24mm.The zero point in the X and Y axishas been determined in the workpiece center with measuring function "Rectangular spigot" and the Zaxis was "set edge" with Z value 1mm determined and stored at zero1 (G54).By pressing the HSK 7 “Face mill.” in the Operatingarea “Machine” and operating mode “JOG” the following input mask will be shown on the screen.M570Page 32828D/840Dsl SINUMERIK Operate

Section 8Face millingNotes8.2Vertical softkey bar (VSK)Display areaDescriptionBy pressing the VSK 1 „Select tool“ you can insert atool. Select the desired tool in the tool list (e.gFACEMILL 50 with the orange selection cursorand press VSK 1 “In program”With VSK 2 ”Graphic view” you can switchover between help screen and graphical view.With VSK 3 "lateral limitation left" you can specifythe lateral limitation in “X-” direction.With VSK 4 "lateral limitation top" you can specifythe lateral limitation in “Y ” direction.With VSK 5 "lateral limitation right" you can specifythe lateral limitation in “X ” direction.With VSK 6 "lateral limitation bottom" you can specify the lateral limitation in “Y-” direction.By pressing the VSK 7 “Cancel” you can escapethe screen “face milling”.With pressing of VSK 8 ”Accept” the following program block is generated:With “CYCLE START“ the cycle “Face milling” willbe executed.828D/840Dsl SINUMERIK OperatePage 33M570

Section 8NotesFace milling8.3Parameters of “Face milling”ParameterUnitDescriptionTTool nameDCutting edge number of the gSpindle speedor constant cutting speedThe following machining operations can beselected:RoughingFinishingDirectionSame direction of machi

This document was produced for training purposes. 828D/840Dsl SINUMERIK Operate Page 1 Siemens assumes no responsibility for its contents. M570 Operating mode “JOG“ 828D/840Dsl SINUMERIK Operate M570 1 Brief description Objective of the module: In this module you learn the different opti

Related Documents:

828D BASIC is the favorably-priced entry into the compact class. This means that SINUMERIK 828 CNCs are always perfectly adapted to the performance requirements of standard machine tools. SINUMERIK 828D and SINUMERIK 828D Basic Optimum scalability in the compact class 8 8.4" PPU 240.2/241.2 n Up to 5 axes / spindles n 1 machining channel

Mar 03, 2010 · SINUMERIK SINUMERIK 840D sl / 828D Measuring cycles Programming Manual Valid for: Control system SINUMERIK 840D sl / 840DE sl / 828D Software CNC software version 4.7 SP2 SINUMERIK Operate for PCU/PC version 4.7 SP2 10/2015 6FC5398-4BP40-5BA3 Preface Fundamental safety instructions 1 Description 2 Measuring variants 3 Parameter lists 4 Changes .

4 SINUMERIK 840D sl/SINUMERIK 828D Depending upon the SINUMERIK CNC and operator panel you’re using, the location of each hard-key may vary. The location of each soft-key, however, will remain the same.

SINUMERIK 828D - Milling Control system overview for machine tools' sales people, 07/2009 3 Preface Scope of validity This document provides you with an overview of the range of functions included in the SINUMERIK 828D Version 2.6 operator panel controller for milling machines. The document is focusing

SINUMERIK Tool and Mold Making Manual Valid for: Control system SINUMERIK 810D SINUMERIK 840D SINUMERIK 840Di SINUMERIK 802D sl pro 08/2007 Edition Doc.Ord.No. 6FC5095-0AB20-0BP0 Basic information 1 Information for machine operators 2 Information for programmers 3 Reference information 4

SINUMERIK 840D/840Di SINUMERIK 810D/FM-NC Short Guide Programming 10.00 Edition Valid for Control Software version SINUMERIK 840D 6 SINUMERIK 840DE (Export version) 6

The contoller types SINUMERIK 840D Solution Line. and SINUMERIK 840D Power Line are supported. Controllers of older types like . SINUMERIK 840. and . SINUMERIK 840C. are not compatible. 2. Which Software Versions are Supported? SINUMERIK 840D sl. must have software version V2.7 and higher, SINUMERIK 840D pl. must have software version V5.3 and .

Adolf Hitler Translated into English by James Murphy . Author's Introduction ON APRIL 1st, 1924, I began to serve my sentence of detention in the Fortress of Landsberg am Lech, following the verdict of the Munich People's Court of that time. After years of uninterrupted labour it was now possible for the first time to begin a work which many had asked for and which I myself felt would be .