Table Of Contents R Panel Rev 4-29-13
Western States R PanelInstallation, Flashings & Shop Drawing Detail GuideSectionTable of ContentsPageSectionNotes to Designer / Installers . 1Fastener Placement and Selection .2-3Key Roof Plan .4Key Flashing / Trims .5-6-7-8Eave Detail 9Mini Eave Detail . .10Eave Pre Hung Gutter . .11Eave Post Hung Gutter . . 12Gutter Splice . 13Gable Flashing . 14Mini Gable Flashing .15Sculptured Gable. . .16Universal Gable Flashing .17Peak/ High Eave . .18Sidewall . .19Endwall . .20Formed Ridge . .21PageHip and Ridge .22Valley 23Pitch Break High to Low . .24Pitch Break Low to High . 25Chimney .26-27-28-29Pipe Flashing .30Wall Detail . . . .31Wall Detail Isometric. 32Wall Base Flashing .33Outside Corner . .34Inside Corner . . .35Notes . 36Custom Trim Form . . .37Special Design Considerations . .38
Western States “R” PanelInstallation, Flashings & Shop Drawing Detail GuideNotes to Designer and InstallersThe details contained in this guide are provenindustry details and are intended to be used asa design aid and installation guide. It does notdepict all situations that may be encounteredon all projects. Modifications are theresponsibility of the designer/ owner/ installer.Consideration should be given for Fit forPurpose, Building use, Climate conditions suchas temperature, snow, wind, and moisture,Governing Building Codes, and Maintenance.It is highly recommended that all trims andflashings be of the same material as the panels(metal, gauge, finish) to ensure long termperformance and durability. Where possible,flashing edges should be hemmed to strengthenthe edge and protect the cut edge fromexposure.Framing and Substrates“R “ panels are used over all type of substrateslike Steel Decking, open purlins, spacedsheathing, and wood decking such as plywood.Most details in this guide are shown with panelsattached to Purlins.Note on underlaymentNot all conditions require an underlayment,However metal roofing is susceptible toCondensation and it is recommended that anappropriate Roofing underlayment be use on allwood substrates to protect the structure duringinstallation. For added protection from rain andsnow, it is recommended to use rubberized Iceand water shield on eaves, valleys, and areas ofroof penetrations.Valley and Snow DesignValley design and dimension must be theproper width to accommodate high snow, rain,ice, and slope conditions. If possible, splices,penetrations, valleys, roof elevation changes,should be minimized in areas of high snow andice accumulations.Oil CanningOil canning is a condition common with flatmetal surfaces. This waviness is caused by steelmill tolerances, forming, variations in thestructures surfaces, and hardness of the steel.Measures are taken at the roll forming process,like profile design, steel gauge, correctiveleveling, to minimize the effects of oil canning.Oil Canning is a Characteristic of steel and cannot be eliminated totally and therefore is notreason for rejection of the panels.Job Site StorageWhile waiting to be installed on the job site,Storage of panels, trim crates, and flat sheetshould be sloped in order to allow for propermoisture run off. One end should be elevatedso as not to allow ponding of water on themetal surface. When using tarps for protection,proper ventilation should be provided toprevent condensation. Moisture orcondensation that is trapped inside a bundlecan lead to white rust on sheeting.ReferencesFor other installation techniques and details,The Sheet Metal and Air ConditioningContractors National Association Inc. (SMACNA)and NRCA manuals are great resources forworking with sheet metal.Technical AssistanceSlope RequirementsIt is recommended that “R” panels have aminimum slope requirement of 1:12 on allstructures.Contact your WSDI sales or technicalrepresentative for any additional information orassistance.1
Western States Metal Roofing “R” PanelInstallation, Flashings & Shop Drawing Detail GuideFastener Placement and SelectionNotes to Installers: Fastener Selection will vary depending on type and thickness of substrate.Space panel lap screws 12” minimum -24” O.C. maximum. Consult with design engineer.Spacing of fastener rows to be engineered by others. Lap panels away from prevailing winds whenever possible.The use of Butyl tape mastic is always recommended on the panel lap when used forroof panels.Panels and flashings should never be installed in contact with dissimilar metals.Use only those flashings and accessories designed for use with this panel.Panel attachment screws must be long enough to fully penetrate through roof decksubstrate or penetrate solid lumber at least one inch. Exposed Fasteners should havesealing washers and be coatedto provide protection againstcorrosion.Screws must be properly drivento ensure holding strength andproper seal. (see diagram)Recommended drill speed is2000rpm. Improper setting ofdrill speed can lead to snappingof screw heads.Pre drilling of screw holes maybe necessary with heavy gaugemetals.2
Western States Metal Roofing “R” PanelInstallation, Flashings & Shop Drawing Detail GuideFastener SelectionDescriptionApplication#9 x1” Wood Drillers#9 x 1.5” Wood Drillers#9 x2” Wood DrillersUsed to attach panels todimensional Lumber andplywood#12-14 x 1” SD#12- 14 x1.5” SD#12- 14 x 2” SD#12-24 x1.25 SDUsed to attach panels toPurlins and other metalsubstrates¼ x 7/8” Lap Self tap¼” x7/8 Lap StainlessUsed to attach Trims andpanel side laps. Stainless tobe used with A606-4 Steel#10-12 x1” Pancake Wood#10-12 x 1” SD Self DrillerUsed to secure trims tosubstrates. Also available inStainless Steel.1/8” Stainless RivetsUsed for Trim to Trimattachment or trim to wallpanels.Stainless Screws#10 x1 Wood Drillers#10 x 1.5 Wood Drillers#10 x 2” Wood DrillersUsed for panel attachmentfor panels made withA606-4 SteelThe table above shows the panel Fasteners provided by WSD. Special order screws are available.2
2
Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048DETAIL:KEY ROOF PLANFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:
EAVE FLASHING WS-204MINI EAVE FLASHING WS-240SCULPTURED EAVE WS-245PITCH BREAK HIGH TO LOW WS-236****PITCH BREAK LOW TO HIGH WS-237CUSTOM TRIM REGLET FLASHING WS-229SCULPTURED GABLE WS-209GABLE FLASHING WS-211*MINI GABLE FLASHING WS-241UNIVERSAL GABLE FLASHING WS-298OVERSIZED VALLEY WS-223STANDARD VALLEY WS-224**Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048STANDARD TRIMFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-ST5
EXTENDED VALLEY WS-225PEAK FLASHING WS-219HEAD TRIM WS-208JAMB TRIM WS-203**BASE TRIM WS-206ENDWALL FLASHING WS-228SIDEWALL FLASHING WS-207RIDGE/HIP CAP WS-205**RIDGE/HIP CAP WS-205HRIDGE/HIP CAP WS-220DIE FORMED RIDGE CAP WS-221RIDGE/HIP CAP WS-220H***Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048STANDARD TRIMFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-ST6
OUTSIDE CORNER WS-202INSIDE CORNER WS-230CRICKET FLASHING CUSTOM TRIM WS-299 SCULPTURED PRE-HUNG GUTTER WS-201***BOX GUTTER PRE-HUNG WS-210BOX GUTTER POST-HUNG WS-215SCULPTURED POST-HUNG GUTTER WS-217 SPLICE WS-213 FOR BOX GUTTER*******SPLICE WS-260 FOR SCULPTURED GUTTERDOWNSPOUT STRAIGHT WS-226DOWNSPOUT ELBOW WS-243DOWNSPOUT WITH KICKOUT WS-227*Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048STANDARD TRIMFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-ST7
DOWNSPOUT STRAP WS-242DOWNSPOUT OUTLET WS-275GUTTER STRAP WS-212BOX GUTTER END CAP WS-214SCULPTURE GUTTER END CAP WS-249Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048STANDARD TRIMFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-ST8
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048EAVE DETAILFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-E1
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048MINI EAVE DETAILFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-ME1
*******GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)EAVE DETAILPRE-HUNGGUTTER DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-EPRG1
*******GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)EAVE DETAILPOST HUNGGUTTER DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-EG2
***GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)GUTTER SPLICEDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-EG3
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)GABLE FLASHINGDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-GF2
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)MINIGABLE FLASHINGDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-MGF2
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)SCULPTUREDGABLE FLASHINGDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-SGF2
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)UNIVERSALGABLE FLASHINGDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-UGF2
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)PEAK FLASHING/HIGH EAVE DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-PK3
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)SIDEWALLFLASHING DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-SW4
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)ENDWALLFLASHING DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-EW5
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)FORMED RIDGEDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-FR6
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)RIDGE/HIPCAP DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-RH6
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048VALLEY DETAILFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-V7
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)PITCH BREAKHIGH TO LOWDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-PB8
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)PITCH BREAK LOWTO HIGH DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-PB9
**GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)CHIMNEY FLASHINGDETAILSPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-CF10
*GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)CHIMNEY FLASHINGDETAILSPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-CF11
**GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)CHIMNEY FLASHINGDETAILSPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-CF12
Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)ISOMETRICCRICKET DETAIL@ CHIMNEYPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-CF13
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)PIPE FLASHINGDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-PF14
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)HEAD AND JAMBDETAILSPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-W15
Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)ISOMETRIC WALLDETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-W16
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048BASE DETAILFax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-W17
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)OUTSIDE CORNERWALL DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-W18
GAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)INSIDE CORNERWALL DETAILPANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-W19
Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comNOTESPhone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-MN19
CUSTOM TRIMGAUGE:COLOR:BREAKS:FINISH:LENGTH:STRETCH OUT:MATERIAL:Western States Metal Roofing901 W. Watkins St.Phoenix, AZ ww.MetalDeck.comCUSTOM TRIM NAME:Phone: (602) 495-0048Fax: (602) 261-7726877-PURLINS (787-5467)PANEL TYPE:R-PanelB01-14-13A06-18-12REV:DATE:DETAIL #:WSD-CT20
Western States “R” PanelInstallation, Flashings & Shop Drawing Detail GuideSpecial Design ConsiderationsThe details contained in this guide are provenindustry details and are intended to be used as adesign aid and installation guide. It does not depictall situations that may be encountered on allprojects. Modifications are the responsibility of thedesigner/ owner/ installer.Consideration should be given for Fit for Purpose,Building use, Climate conditions such astemperature, snow, wind, and moisture, GoverningBuilding Codes, and Maintenance.It is highly recommended that all trims and flashingsbe of the same material as the panels (metal, gauge,finish) to ensure long term performance anddurability. Where possible, flashing edges should behemmed to strengthen the edge and protect the cutedge from exposure.AcceptanceUse of this manual is strictly voluntary. Details thatare provided are to be used as a guide only. Detailsmay not be applicable for all situations. This guideprovides one standard detail and WSDI accepts thatother installation details may be needed and otherdetails may exist. WSDI makes no guarantee as tothe Weather Tightness of the system or detailsfound with in this guide. The information in thismanual is believed to be correct and accurate at thetime of printing. WSDI reserves the right to changedetails, discontinue products, change designs at anytime without incurring obligation. It is best to consultyour Design Engineer for recommendations.UnderlaymentThere are many types of underlayment’s on themarket today. All designed with a special purposedepending on the type of Metal and profile. Manydifferent types of metal will require a different typeof underlayment, such as A606-4 (Corten) whichrequires a High Temperature underlayment. It is bestto consult your Design Engineer forrecommendations.Valley and Snow DesignValley design and dimension must be the properwidth to accommodate high snow, rain, ice, andslope conditions. If possible, splices, penetrations,valleys, roof elevation changes, should be minimizedin areas of high snow and ice accumulations. Detailsfound in this manual may not pertain in areas of highsnow and ice accumulations.Panel Coverage and FasteningNormal panel width of “R” panel is 36”. Howeverdepending on the finish selected and the requiredcoil feed, it may be necessary for WSD to shorten thewidth of the panel. Please consult with your WSDIrepresentative for details and fasteningrecommendations.Safety and MaintenanceWalking on and installing any roof is dangerous!Extreme care should always be used when walkingon roofs. Safety should always be a top priority andapproved fall protection and equipment as approvedby OSHA should always be used.No roof is immune to severe weather or iscompletely maintenance free. To keep your roofperforming as it was designed; an inspection andcomprehensive maintenance program should beimplemented.ReferencesFor other installation techniques and details, TheSheet Metal and Air Conditioning ContractorsNational Association Inc. (SMACNA) and NRCAmanuals are great resources for working with sheetmetal.Technical AssistanceContact your WSDI sales or technical representativefor any additional information or assistance. Toinsure you have the latest information available,please inquire or visit our web sites atwww.metaldeck .com or Rustedroofing.com1
eave flashing ws-204 mini eave flashing ws-240 sculptured eave ws-245 pitch break low to high ws-237 oversized valley ws-223 custom trim reglet flashing ws-229 sculptured gable ws-209 gable flashing ws-211 standard valley ws-224 pitch break high to low ws-236 mini gable flashing ws-241 universal gable
Hush Panel 28 Hush Panel 32 Hush Panel 33 Hush Panel 37 Hush Panel 48 Hush Panel 52 Hush Ply 28 Hush Ply 32 When installing Hush Cem Panel 28 or Hush Cem Panel 32 the tongue and groove joints are to be glued using Hush Cem Panel Adhesive. All joints to be glued, on all sides of the panel to give the best bond. Adhesive not to be spared .
Creating a table of contents The Insert Index/Table window (Figure 1) has five tabs. All of them can be used when creating a table of contents: Use the Index/Table tab to set the attributes of the table of contents. Use the Entries and Styles tabs to format the entries in the table of contents. Use the Background tab to add color or a graphic to the background of the table of
the transverse panel-to-panel connections are referred to simply as panel-to-panel connections. Panel-to-panel connections can be nonprestressed or post- . (25 100 mm) flat plastic duct (Fig. 5). One of the connections with a stress of 340 psi (2.34 MPa) had an epoxy bonding agent applied to the
Attach and remove the control panel You can attach the control panel directly to the drive, or use a separate mounting kit. To attach the control panel to a drive: 1. Place the bottom end of the control panel into the slot in the drive. 2. Press the control panel lock clip down. 3. Push the control panel into place. To remove the control panel:
PANEL HEMMING TOOL TremLock SL Field Hem 1 1/2" TremLock SLPanel TremLock SL Panel TremLock SL Panel Field Notch Panel Hemming Tool Panel Hemming Tool Panel Hemming Tool NOTES: 1. Cut through male and female legs/ribs 1 1/2" up from panel end as shown. 2. Then cut diagonally with metal shears as shown. 3. Place hemming tool over panel tab. 4.
a GuiDe for public Sector uSerS june 2014 Dpp2 panel HANDBOOK centenary Quay, Woolston. 2 01 introduction 02 Scope of the panel 03 use of the panel by other public Sector bodies 06 panel Membership 07 framework agreement 07 Subcontracting 08 the procurement process 09 contractual Structure of panel Members CONTENTS 10 procurement of Works and Services from the panel 11 Scope of the Mini .
4.5 The Bell panel 4.6 The Features panel 4.7 The Window panel 4.8 The Appearance panel 4.9 The Behaviour panel 4.10 The Translation panel 4.11 The Selection panel . 2.2 Verifying the host key (SSH only) 2.3 Logging in 2.4 After logging in 2.5 Logging out. 2.1 Starting a session When you st
7. Place ceiling panel #8 into position and lock it to ceiling panel #7 first, then to the wall panels, leaving the wall-to-ceiling panel camlocks nearest the exposed ceiling panel seam on either side of ceiling panel #8 unlocked. Lock the two wall-to-ceiling panel camlocks left unlocked in step 4 to panel #7.
