2001 Volvo V70 XC AWD L5-2.4L Turbo VIN 58 B5244T3 Wheel .

3y ago
15 Views
2 Downloads
1.83 MB
17 Pages
Last View : 16d ago
Last Download : 2m ago
Upload by : Axel Lin
Transcription

2001 Volvo V70 XC AWD L5-2.4L Turbo VIN 58 B5244T3Wheel BearingService and RepairSpecial Tools951 2050999 5259999 5562999 5563PreparationRemove* the wheel.* the ABS sensor. Detach the ABS sensor cable from the spring strut.

Remove the 2 mounting screws on the brake caliper.Hang up the brake caliper, for example on the spring strut.Note! Take care not to damage the brake hose while working.

Remove the screw holding the drive shaft. Counterhold the brake disc with a screwdriver.Remove* the brake disc locating pin.* the brake disc.

Tap the end of the drive shaft into the hub approximately 10 - 15 mm (0.39" - 0.59") . Use a brassdrift.Remove the upper anti-roll bar link from the spring strut.

Remove the steering arm from the stub axle. Use puller 999 5259.

Blow clean around the ball joint with compressed air.Generously spray rust penetrant on to the area around the ball joint and the screw and nutretaining the ball joint.

If the screw has rusted solid, slacken off the nut a few turns and knock the screw so that itloosens.Remove the nut and screw.Spray the ball joint with rust penetrant again.Note! Do not insert a screwdriver or punch between the "ears" on the stub axle.

Tap the ball joint off the stub axleUse a sleeve as a spacerNote! The inner diameter of the sleeve must be larger than the outer diameter of the cover. Thisis to prevent damage to the cover.Spray the ball joint with rust penetrant again.

Move the ball joint up and down by hand (alternatively a jimmy bar can be used) until the balljoint detaches from the stub axle.Install protective sleeve 999 5562 on the ball joint.

Secure the control arm in the depressed position using tool 999 5563.Remove the drive shaft from the hub.

Turn the spring strut a half turn and "lock" it by placing the steering arm on the control armNote! Take care not to damage the brake hose.Hang the drive shaft on the spring strut.Replacing the front wheel bearing / hubRemove the wheel bearing unit.

Check the stub axle surfaces mating against the wheel bearing unit.Also check the screw head mating surfaces on the stub axle.Lubricate all the mating surfaces a little.Install the wheel bearing unit with new screws.Lubricate the outer threads a little and tighten crosswise to 65 Nm (47.9 ft. lbs.).Angle-tighten the screws for the wheel bearing unit to 60 . Use protractor 951 2050.

Check the drive shaft for damage to the mating surfaces with the wheel bearing.Check the booms (splines).Clean the pulse wheel and check the shape of its cogs.Lubricate the booms (splines) and mating surfaces to the wheel bearing a little.Detach the drive shaft from where it was placed earlier.Turn the spring strut a half turn to detach it from the control arm.Note! Take care not to damage the brake hose.

Install the drive shaft in the hub by hand, but only to the extent that the drive shaft can easilymove backward and forward in its positionLubricate a new drive shaft screw and screen it in a few turns by hand.Clean off any rust from the ball joint and stub axle.Lubricate the ball joint pinion and the stub axle.Install the ball joint in the stub axleNote! Press the ball joint upwards so that the conical top is visible above the screwed joint on thestub axle.

Install the screw and a new nut.Tighten to 50 Nm (36.9 ft. lbs.).Check the dust boot on the anti-roll bar link for damage.Check the link threads for damage.Lubricate the threads.Reinstall the upper link of the anti-roll bar on the spring strut. Use a new locknut. Tighten to 50Nm (36.9 ft. lbs.).Install the tie rod on the stub axle. Use a new locknut.Tighten to 70 Nm.

Check that the brake disc mating surfaces to the wheel bearing unit are smooth and even.Install* the brake disc.* the brake disc locating pin. Tighten to 8 Nm (5.9 ft. lbs.).Check the mating surfaces of the brake caliper and stub axle.Clean and grease the surfaces of the steering limiter.Install the brake caliper. Use new screws. Tighten to 100 Nm (73.8 ft. lbs.).Tighten the center screw of the drive shaft to 50 Nm (36.9 ft. lbs.). Counterhold the brake discwith a screwdriver.

Clean and check that the ABS sensor mating surface on the stub axle is flat.Apply a very small amount of grease to the mating surface.Install the ABS sensor cable in the holder on the spring strut.Install the ABS sensor. Lubricate the screw and tighten to 10 Nm (7.4 ft. lbs.).Install the wheelInstall the wheel studs lightly. Then tighten them crosswise to 110 Nm (7.4 ft. lbs.).

2001 Volvo V70 XC AWD L5-2.4L Turbo VIN 58 B5244T3 Wheel Bearing Service and Repair Special Tools 951 2050 999 5259 999 5562 999 5563 Preparation Remove * the wheel. * the ABS sensor. Detach the ABS sensor cable from the spring strut.

Related Documents:

Volvo 3P-AE 15500 4 Volvo Group Trucks Buses Construction Equipment Volvo Penta Volvo Aero Financial Services Volvo 3P Volvo Powertrain Volvo Parts Volvo Logistics Volvo Information Technology Volvo Group Real Estate, Volvo Technology Volvo Business Services. Volvo 3P-AE 15500 5 AE-Curitiba

VOLVO V70 & XC70 Owners Manual Web Edition. DEAR VOLVO OWNER THANK YOU FOR CHOOSING VOLVO We hope you will enjoy many years of driving pleasure in your Volvo. The car has been designed for the safety and comfort of you and your passengers. Volvo is one of the safest cars in the world. Your Volvo

Phonak Virto V-10 NW O V90/V70/V50 Phonak Virto V-10 O V90/V70/V50 Phonak Virto V-312 V90/V70/V50 Phonak Virto V-13 V90/V70/V50 Phonak Virto V-10 V90/V70/V50 Roger Roger X / Phonak ComPilot II Roger MyLink Trådlösa tillbehör Phonak DECT II Phonak PilotOne II EasyCall II Phonak ComPilot II Phonak ComPilot Air II Ph

the Volvo tonality for pictures. See Volvo Brand Communication Guideline for click the Compress further information. Only use these approved Volvo colors. Use the colors in 100% only – never in tints. For more information and RGB color codes please select the Volvo Layout “Volvo Brand Colors”. Volvo Profile colors Volvo Accent colors

John Deere 425 445 455 Service Repair Manual in the technological know-how of archaeology. . mini volvo excavator volvo mini excavators wheel loaders volvo volvo wheel loader . volvo l90 specs gold rush excavator volvo ec750e specs volvo 290 volvo motor grader volvo

volvo construction equipment parts . Cat Caterpillar 416c Backhoe Loader Service Repair Manual champion motor graders shippensburg volvo volvo off road truck . champion grader volvo construction equipment dealer near me volvo 160 a25g volvo volvo ecr88 specs volvo heav

VOLVO V70 & XC70 Owner's Manual Web Edition. Welcome to the world-wide family of Volvo owners. We trust that you will enjoy many years of safe driving in your Volvo, an automobile designed with your safety and comfort in mind. We . service and repair facilities

8 Annual Book of ASTM Standards, Vol 14.02. 9 Annual Book of ASTM Standards, Vol 03.03. 10 Annual Book of ASTM Standards, Vol 03.06. 11 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036. 12 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990. 13 .