Fisher Vee-Ball V150, V200, And V300 Rotary Control Valves
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Fisher Vee-Ball V150, V200, and V300Rotary Control ValvesThis bulletin covers the DN 25 through 600 (NPS 1through 24) V150, V200 and V300 Vee-Ball controlvalves. The Vee-Ball valve combines globe valveruggedness with the efficiency of a rotary valve. TheVee-Ball valve is a segmented ball valve which featuresa contoured segmented V-Notch ball. A shearingaction between the V-notch ball and the ball seal(figure 1) promotes smooth, nonclogging operation.The unrestricted straight-through flow design provideshigh capacity for gas, steam, liquids, and fibrousslurries.V150, V200, and V300 valves mate with a variety ofASME raised face flanges, as well as with EN flanges(see Specifications).X0187To meet specific application requirements, a variety ofmetal and soft ball seal materials are available. Asplined drive shaft combines with a variety of poweroperated and manual actuators to provide reliable,high-performance throttling or on-off operation formany different applications in the process industries.V150FeaturesnTrim Versatility—Trim components areinterchangeable between V150, V200, and V300valves. This feature allows you to reduce your spareparts inventory and maintenance procedures. Theseal assembly can be changed without removingthe actuator or without removing the ball from thevalve body.nEasy Installation—Flanged body design of the V150and V300 eliminates exposed line flange bolting,reduces alignment and installation time, andpromotes secure valve installations and pipingintegrity. The V200 is available with flanges in NPS 2through 8.www.Fisher.comX0337V200Typical Vee-Ball Valves with Fisher 2052 Actuators andFIELDVUEt DVC6200 Digital Valve Controllers
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Specifications(Bidirectional Flow): Class III per ANSI/FCI 70-2 andIEC 60534-4Flow Ring Construction (Bidirectional Flow): 5% ofvalve capacity at full travelMicro-Notch Ball with HD Seal: 4 SCFH (Leakage rateequivalent to Class IV for standard ball. This is basedon the capacity of a standard ball.)Valve SizesSee table 1Valve End Connection StylesV150: Flanged valves that mate with CL150raised-face flanges and EN 1092-1 Type B raised-faceand Type F RecessConstruction MaterialsV200: Flangeless (all sizes) and flanged valves thatmate with CL600 raised-face flanges (NPS 2-8)See tables 4 and 5V300: Flanged valves that mate with CL300raised-face flanges and EN 1092-1 Type B raised-faceand Type F RecessTemperature Capabilities(1,2)Composition SealsFisher TCM Plus: -46 to 232 C (-50 to 450 F)Fisher TCM Ultra: -46 to 260 C (-50 to 500 F)HD Metal Seals: -46 to 288 C (-50 to 550 F)PEEK HD Seal: -46 to 232 C (-50 to 450 F)High Temperature HD Metal Seal: 288 to 427 C (550to 800 F). Contact your Emerson sales office or LocalBusiness Partner if higher temperatures are required.Ceramic Micro-Notch Ball: -46 to 93 C (-50 to200 F)(4)Flow Ring or Flat Metal Seal : -198 to 425 C (-325 to800 F)PEEK/PTFE Bearings: -198 to 260 C (-325 to 500 F)Maximum Inlet Pressures(1)V150 or V300 WCC (or 1.0619 Steel), CF3M (or1.4409 SST), CG8M, LCC, M35-2, CK3McuN, CD3MN,and CD3MWCuN Valves: Consistent with CL150 forV150 or CL300 for V300 pressure-temperatureratings per ASME B16.34 or with PNpressure-temperature ratings shown in table 1.Note: CF3M is the standard material offering inEurope and Asia-Pacific. 1.0619 Steel and 1.4409 SSTare also standard material offerings in Europe.V200 WCC, CG8M, and LCC Valves: Consistent withapplicable pressure-temperature ratings in table 1 perASME B16.34.Packing ConstructionsPTFE V-ring: -46 to 232 C (-50 to 450 F)Graphite: -198 to 538 C (-325 to 1000 F)ENVIRO-SEALt Single PTFE V-ring: -46 to 232 C (-50to 450 F) (for 100 ppm service requirements)ENVIRO-SEAL Graphite: -7 to 316 C (20 to 600 F) (for100 ppm service requirements). This packingarrangement can be used to 371 C (700 F) fornon-environmental service.CW2M: Consistent with applicablepressure-temperature ratings shown in table 6.Do not exceed the material temperature capabilitiesshown below or the pressure drop limitations.Maximum Shutoff Pressure/Temperature Ratings(1)Composition (Fisher TCM Plus or TCM Ultra), FlatMetal (NPS 3 through 12 valves only), HD and HighTemperature HD Metal Ball Seals and Flow Ring: Seetable 8.Flow CharacteristicModified equal percentageShutoff Classification(1)DimensionsFisher TCM Plus or Ultra Ball Seal (Forward Flow):Class VI per ANSI/FCI 70-2 and per IEC 60534-4,Flat Metal Ball Seal for NPS 3 through 12 only(Forward Flow): Class IV per ANSI/FCI 70-2 and per IEC60534-4,HD (Heavy Duty) Ball Seal (Bidirectional Flow): 0.01%of valve capacity; Class IV per ANSI/FCI 70-2 and IEC60534-4; Maximum allowable pressure drop inreverse flow is 6.9 bar (100 psi);High Temperature HD (Heavy Duty) Ball SealSee figures 7, 8, and 10 for dimensionsFace-to-Face DimensionsJ Standard Face-to-Face dimensions comply with ISAS75.08.02J ASME B16.10 short face-to-face dimensions areavailable as an option for NPS 1 through 12 valves.Note that ASME B16.10 short dimensions are longerthan ISA S75.08.02. See figure 11 for dimensions.(continued)2
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Specifications (continued)Standard Flow DirectionForward (into the convex face of the V-notch ball)Flow Coefficients, Flow Coefficient Ratio(3), andNoise LevelsSee Fisher Catalog 12Maximum Ball Rotation90 degreesActuator MountingStandard valve construction is for right-handmounting, as viewed from upstream end of valve.Left-hand (optional) mounting is available uponrequest(5)Valve/Actuator ActionWith diaphragm or piston rotary actuator, the valve isfield-reversible between PDTC or PDTO:J push-down-to-close (extending actuator rod closesvalve) and J push-down-to-open (extendingactuator rod opens valve)Approximate WeightSee table 2OptionsJ Pipe plug at end of follower shaft for all sizes,J Line flange bolting, J Materials that arecompatible with sour service, J Alloy constructionmaterials, J ENVIRO-SEAL packing system: See figure6 and Bulletin 59.3:041, ENVIRO-SEAL PackingSystems for Rotary Valves (D101638X012) for moreinformation, J Micro-Notch construction forNPS 1 valves (see Micro-Notch Construction section),J Alloy trim material , J Chrome Carbide coatedinternals (NPS 2 through 12), J Rotary attenuator toreduce aerodynamic noise and cavitation effects,J Double D, Square, and Keyed shaft options1. The pressure/temperature limits in this bulletin, and any applicable code or standard limitation, should not be exceeded.2. Additional limits are shown in tables 6, 7 and 8.3. Ratio of maximum flow coefficients to minimum usable flow coefficient can also be called rangeability.4. For the CG8M and alloy 6 Micro-Notch constructions, pressure and temperature capabilities are the same as for standard constructions.5. True left-hand mount is not available for Micro-Notch constructions, as it will cause the ball to rotate to the bottom of the valve body.Table of ContentsFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Series B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Micro-Notch Construction . . . . . . . . . . . . . . . . . . . . . . 8Severe Service Attenuator . . . . . . . . . . . . . . . . . . . . . . 9Pressure Drops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018Features (continued)nnn4Application Versatility—The valves are available withISA S75.08.02 and IEC 534-3-2 face-to-facedimensions as a standard construction, andoptional ASME B16.10 short face-to-facedimensions. IEC 534.3.2 face-to-face dimensionsare equivalent to S75.08.02 face-to-facedimensions.Long Service Life—The solid HD ball seal (figures 1and 2) construction provides long service life indemanding applications. The constant wipingaction of the seal across the ball's sealing surfaceprevents scale and sludge buildup, and providesexcellent service on steam, gases, slurries, andvarious liquid applications.Excellent Flow Control—Precise contouring of theVee-Ball provides a modified equal percentage flowcharacteristic. For very precise control of low flowrates, the Micro-Notch option is available on theNPS 1 valve. See the Micro-Notch Constructionsection of this bulletin for more information.D101363X012nSour Service Capability—Materials are available forapplications involving sour liquids and gases. Theseconstructions comply with NACE MR0175-2002,MR0175-2003, MR0103, and MR0175/ISO 15156.nQuick and Easy Maintenance—Ball seal inspectionand replacement is done at the valve body inletwithout removing the actuator or disassembling thevalve. Valve maintenance requires no special tools.nSmooth Valve Operation—Precision machined partsand pressure balanced seal designs allow smooth,precise movement of the ball.nStructural Integrity—One-piece valve body improvesstructural integrity of the pressure boundary byeliminating leak paths that could be caused by thegaskets in two-piece, bolted valve designs.nExceptional Environmental Capabilities—Theoptional ENVIRO-SEAL packing systems aredesigned with very smooth shaft surfaces and liveloading to provide exceptional sealing. The seal ofthe ENVIRO-SEAL system can restrict emissions toless than the EPA (Environmental ProtectionAgency) limit of 100 ppm (parts per million).
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 1. Valve Body Materials, End Connections, and RatingsVALVE DESIGNVALVE BODY MATERIALWCCRATINGSASME / PNNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20, 24x20(5)CL150DN 80, 100, 150PN 10-16DN 200, 250, 300PN 10 or PN 16WCC / 1.0619(1)V150SIZENPS / DNNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL150LCCDN 80, 100, 150PN 10-16DN 200, 250, 300PN 10 or PN 16CF3M(2)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL150DN 80, 100, 150PN 10-16DN 200, 250, 300PN 10 or PN 16CF3M/1.4409(1)R50550NPS 1, 1-1/2, 2, 3, 4, 6CG8MNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20, 24x20(5)CW2MNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12M35-2NPS 1, 1-1/2, 2, 3, 4, 6, 8CD3MN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CD3MWCuN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CK3MCuNNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12NPS 1, 1-1/2, 2CL150/300/600 flangelessNPS 3, 4CL150 and CL300/600flangelessNPS 6, 8CL150/300 and CL600flangelessNPS 10CL150 flangelessWCC, LCC, CG8M, or CF3M(2)V200(4)WCC, LCC, or CG8MNPS 2, 3, 4, 6, 8CL600CW2M, M35-2, or CK3MCuNNPS 1, 1-1/2, 2, 3, 4, 6, 8CL150/300/600 flangelessCK3MCuNNPS 10CL150 flangelessWCCNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20CL300DN 25, 40, 50PN 10-40WCC / 1.0619(1)LCCCF3M(2)V300CL150CF3M/1.4409(1)DN 80, 100, 150PN 25-40DN 200, 250, 300PN 25 or PN 40NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL300DN 25, 40, 50PN 10-40DN 80, 100, 150PN 25-40DN 200, 250, 300PN 25 or PN 40NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL300DN 25, 40, 50PN 10-40DN 80, 100, 150PN 25-40R50550NPS 1, 1-1/2, 2, 3, 4, 6CL300CF3M/1.4409(1)DN 200, 250, 300PN 25 or PN 40CG8MNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12, 14, 16, 20CW2MNPS 1, 1-1/2, 2, 3, 4, 6, 8M35-2NPS 1, 1-1/2, 2, 3, 4, 6, 8CD3MN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CD3MWCuN(3)NPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CK3MCuNNPS 1, 1-1/2, 2, 3, 4, 6, 8, 10, 12CL3001. WCC and EN Stl 1.0619 are dual certified. CF3M and EN SST 1.4409 are dual certified.2. CF3M is a standard offering in Europe and Asia Pacific.3. NORSOK compliant materials available upon request.4. Flangeless V200 assemblies mate with raised-face flanges.5. Valve body mates with NPS 24 ASME CL150 flanges. Internal based on NPS 20 valve design.5
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Figure 1. Vee-Ball Construction Features, Seals (Fisher V150 Shown)SEALPROTECTORRINGSEAL PROTECTORRINGBODYHD LLW4713-3SHIMSBODYVIEW AFLAT METAL BALL SEAL DETAILFOR DN 80 THROUGH 300(NPS 3 THROUGH 12)WAVESPRINGV-NOTCH BALLW5704-1VIEW AHD BALL SEAL DETAILSEAL PROTECTORRINGSEALPROTECTORRINGTCMBALL SEALV-NOTCHBALLBODYW6197-1VIEW AFISHER TCM PLUS BALL SEALDN 25, 40, AND 50(NPS 1, 1-1/2, AND 2) VALVESBACKUPRINGVIEW AFLOW RING DETAILSEALPROTECTORRINGSEALPROTECTOR RINGRETAININGRINGSPISTONRINGPISTON RINGHDMETAL SEALWAVESPRINGHDMETALSEALWAVESPRINGRETAINING RING(USE ONLY WHENATTENUATOR ISUSED)W8479DN 25, 40, AND 50(NPS 1, 1-1/2 AND 2)HD BALL SEALDN 8 THROUGH 200 AND DN 350 THROUGH 600x500(NPS 3 THROUGH 8 AND NPS 14 THROUGH 24x20)HD BALL SEALVIEW AHIGH-TEMPERATURE HD BALL SEAL6DN 250 AND 300(NPS 10 AND 12)HD BALL SEAL
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Figure 2. Vee-Ball Construction Features (Fisher V150 Shown)V-NOTCH BALLSEE VIEW A(FIGURE 1)SEALPROTECTORRINGGASKETFOLLOWERSHAFTGROOVE PINBODYDRIVE SHAFTBEARINGTAPER KEYPACKING FOLLOWERW7435DN 80 THROUGH 300(NPS 3 THROUGH 12) VALVES(HD BALL SEAL SHOWN)HD BALL SEALBOTTOMFLANGEPACKING FLANGEAND PACKING FOLLOWERPINW6099-1DN 350, 400, 500 and 600x500(NPS 14, 16, 20, and 24x20) VALVES(HD BALL SEAL)7
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 2. Valve Weights, ApproximateVALVE ------Series BNPS 3 through 12 have been changed to reduce partsand to improve control performance. The V-notch Ballnow resembles the NPS 14 through 24x20 V-notchBall. The pressed-in bushings have been eliminated, aswell as the thrust washer.Micro-Notch ConstructionFor very precise control of low flow rates, theMicro-Notch construction (see figure 3) is available onDN 25 (NPS 1) valves. Three Micro-Notch ball materialsare available: chrome-plated CG8M (317 stainlesssteel), solid alloy 6, and solid VTC ceramic. A VTCceramic HD seal is standard with the VTC ceramic ball.For the CG8M and alloy 6 constructions, pressure andtemperature capabilities are the same as for standardconstructions. For the ceramic construction,maximum temperature is 93 C (200 F).8Figure 3. Typical Micro-Notch Ball and ShaftMICRONOTCHVEE BALLDRIVE SHAFTW6256For further information, please refer to the FisherVee-Ball V150, V200 and V300 Rotary Control ValvesNPS 1 through 12 instruction manual (D101554X012).In addition to the standard Micro-Notchoffering, options are available in both low(Micro-Scratch) and high (Macro-Notch)flow construction. Contact your Emerson sales officeor Local Business Partner for more information.
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Severe Service AttenuatorFisher Vee-Ball series valves (V150, V200, and V300),with the severe service attenuator, combine theefficiency of a rotary valve with the energy absorbingcapability of a special trim to provide improvedperformance for demanding applications. The Fisherattenuator design can be utilized in both liquid and gasservice to reduce cavitation and noise effects thatcause pipeline vibration. See table 3 for a competitivecomparison.The attenuator will not change the NACE complianceof the Vee-Ball valve. When a rotary noise attenuator isinstalled in a Vee-Ball valve, the V-Notch is no longer apoint of high-velocity erosion. As a result, the CoCr-AV-Notch option is not required when a rotaryattenuator is used. The rotary attenuator and CoCr-AV-Notch options are not available together.nAttenuator-Ball Fabrication — The ball-attenuatorconstruction provides structural integrity becauseof its rugged fabrication weld.nAttenuator Performance — Up to -10 dBA acousticalattenuation, and a Kc 1.0 for hydrodynamics areachievable depending on service conditions.Attenuator Ball MaterialStandard attenuator ball material is CG8M, M35-1,CW2M, or CK3McuN.Standard Flow DirectionForward flow direction is into the convex face of theV-notch ball. The valve with the attenuator must beplaced in the forward flow direction for the attenuatorto be effective.FeaturesnTrim Versatility — Trim components areinterchangeable for Fisher V150, V200, and V300valves. This feature allows you to reduce your spareparts inventory and maintenance procedures.Actuator MountingRight-hand or left-hand as viewed from the upstreamend of the valve. Counter-clockwise to close for bothmounting styles.9
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Figure 4. Fisher Vee-Ball Series Noise Attenuator BallFigure 5. Fisher Vee-Ball Series Rotary AttenuatorConstructionW6116-1W6129-1Table 3. Segmented Ball Benefits Analysis Comparison10BenefitsTypical CompetitiveDeviceFisher Vee-BallAttenuatorPredictable PerformanceNoYes-10 dBA Aerodynamic Noise AttenuationNoYesSuperior Attenuation Effect at Critical Opening PositionNoYesMaximum Pressure Drop CapabilityNoYesHeavy Duty, Integrally Welded Attenuator/Ball AssemblyNoYesValve Splined Shaft Connects to Clamped Actuator Lever to Minimize Lost MotionNoYesSuperior Soft Seats for Tight ShutoffNoYesModerate Kc Improvement vs Unattenuated DeviceYesYesTrunnion Mounted Ball for Superior Wear ResistanceYesYesHeavy Duty Metal Seats for Demanding ApplicationsYesYes
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 4. Materials of Construction for DN 25 through 300 (NPS 1 through 12) ValvesPARTValve Body and SealProtector Ring orFlow RingBackup Ring [DN 25, 40, and 50 (NPS 1, 1-1/2, and 2) only]MATERIALWCC steel (EN 1.0619), CG8M (317 SST), R50550(10), CF3M(1) (316L SST EN 1.4409 oroptionalEN 1.4581), CD3MN, CD3MWCuN, CW2M (CW2M valve available with Fisher TCM Plusseal only), M35-2 or CK3MCuNCG8M, CF3M(1), R50550, or CW2MSegmented V-Notch BallCG8M, R50550, CF3M, CW2M, chromium-plated CF3M, chromium-plated CG8M,chromium-plated CG8M with alloy 6 notch, chromium-plated CF3M with alloy 6 notch,chromium-plated CD3MN, chromium-plated CD3MWCuN, M35-1, or CK3MCuNSealFisher TCMFisher TCM Plus and Fisher TCM UltraFlat Metal Seal, Shims, and Spring Seal(7)Spring Tempered S31600 (316 stainless steel) orSpring Tempered S30200 (302 stainless steel) for NPS 12 valves onlyHD (Heavy-Duty) Ball SealCF10SMnN(2) , CD7MCuN(3) (alloy 255duplex stainless steel) or R30006 (Alloy 6)High Temperature HD SealR30006 (Alloy 6)Wave Spring (use with HD seal)N07750HD Seal Radial SealGraphite reinforced PTFEHigh Temp HD Seal Piston RingGraphite FMS 17F39BearingsPEEK(4)/Carbon-filled PTFE liner, S31603 Nitride,R30006 (alloy 6), silver-plated R30006,N10276 with carbon-filled PTFE liner, or N10276 with glass-filled PTFE linerSeal Retainer GasketLaminated graphitePackingPTFE V-ring with one carbon-filled PTFE ring(5), PTFE V-ring, graphite ribbon,ENVIRO-SEAL PTFE, or ENVIRO-SEAL graphiteShaftsS20910, S17400 (17-4PH stainless steel),N10276, N05500, S31254(8), R50550, or S32760(8)Groove PinR50550, S31600 or N10276Taper KeyR50550, R30006(6), S20910, or N10276Taper Pin [DN 25, 40, and 50 (NPS 1, 1-1/2, and 2) only]R50550, S20910, or N10276Pipe Plug (Optional)S31600 N10276, or S31603 (316L stainless steel)Seal Retainer Screws and WashersStainless steelPacking Follower and Packing Box RingR50550, CF8M (316 stainless steel), N10276, S312254, or N10276with separate S31600 packing box flangeActuator Mounting Bolts and NutsGrade 5 steel or strain-hardened B8M stainless steelSpacer and BushingS31700, N10276, or S31603Packing Follower Bolting and Optional Line BoltingSA-193-B7, SA-193-B7M, or strain-hardened SA-193-B8MAttenuator(9)CG8M, M35-1, CW2M, or CK3MCuN1. CF3M is available in all areas as a special order and is the standard material offered in Europe.2. Recommended for lubricated and non-lubricated service and where corrosion properties similar to 304 stainless steel are acceptable.3. Recommended for lubricated service and where corrosion properties equal to or better than 317 stainless steel are required.4. PEEK is poly-ether-ether-ketone.5. The carbon-filled PTFE ring is used for grounding.6. Standard material offered in North America.7. Offered for lubricated service only.8. S31254 and S32760 shafts may cause the valve to be derated. Contact your Emerson sales office or Local Business Partner.9. Attenuator material will match segmented V-Notch ball material.10. R0550 is available with TCM seat. For other seal availability contact your Emerson sales office or Local Business Partner.11
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 5. Materials of Construction for DN 350, 400, 500, and 600x500 (NPS 14, 16 20, and 24x20) ValvesPARTMATERIALValve Body, Seal Protector Ring, and Flow RingWCC steel or CG8M (317 stainless steel)Segmented V-Notch BallChromium-plated CG8M, CG8M, Chromium-plated CG8M with alloy 6 notchBall SealFisher TCMFisher TCM Plus and Fisher TCM UltraHD (Heavy-Duty Metal)CF10SMnN(1) , CD7MCuM(2) (alloy 225 duplex stainless steel) or CG8M/CoCr-AWave Spring (use with HD seal)N07750Radial Seal (use with HD seal)PTFE with N10276 springBearingsPEEK/PTFE(3), S44004 (440C stainless steel--use with S17400 [17-4PH stainless steel]shafts, alloy 6B, and silver plated alloy 6BThrust Washer (use with metal bearings)Alloy 6BSeal Retainer GasketLaminated GraphitePackingPTFE V-ring with one conductive V-ring(4), PTFE V-ring, graphite ribbon, ENVIRO-SEALPTFE, or ENVIRO-SEAL graphiteShaftsS17400 (17-4 stainless steel) or S20910PinsS20910Pipe PlugS31700 (317 stainless steel)Packing Follower BoltingB7M steel or strain-hardened B8M stainless steelRetainer ScrewB8M stainless steelPacking Follower and Packing Box ringS31600 (316 stainless steel)Packing FlangeSteel or S31600Actuator Mounting Bolts and NutsGrade 5 steel or strain-hardened B8M stainless steelGasket (used with bottom flange)S31603 (316L stainless steel) spiral woundStud and Hex Nut (used with bottom flange)B7 steel or strain-hardened B8M stainless steelAttenuatorCG8M1. Recommended where corrosion properties similar to 304 stainless steel are acceptable.2. Recommended for lubricated service and where corrosion properties equal to or better than S31700 stainless steel.3. PEEK (Poly-ether-ether-ketone) w/PTFE liner.4. A carbon-filled PTFE ring is used for grounding.Figure 6. Typical ENVIRO-SEAL Packing ArrangementsPACKINGBOX SVALVESHAFTPACKINGFLANGEPACKINGBOX 2PTFE HITE PACKINGPACKINGBOXRINGGRAPHITEPACKINGSET
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 6. Maximum Allowable Inlet Pressure for CW2M ValvesTEMPERATURECW2M(1)150(2)300(2)PN 10(2)C–46 to 0750730700680145144137133133F–50 to 100200300400450PN 16(2)PN 25(2)PN 2331331580575548530530BarPsi1. This material is not listed in EN 12516‐1 or ASME B16.34. Also see the Installation section.2. The designations PN or 150 and 300 are used only to indicate relative pressure‐retaining capabilities and are not EN or ASME pressure‐temperature rating class designations.Pressure DropsPressure drop limits of any given valve are based onvalve body, and trim material limits. To find theappropriate pressure drop limitation, choose thedesired valve size and temperature range. Then searchtable 7 for body limitations and table 8 for trimlimitations. Information on limits for S31254, CW2M,M35-2, CD3MN, CD3MWCuN, and other alloyconstructions can be obtained by contacting yourEmerson sales office or Local Business Partner. Thelowest number from the tables is the appropriate limit.The tables for both trim and body limits must beconsulted.13
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 7. Maximum Allowable Shutoff Pressure Drops (Body Ratings).(Tables for both trim and body limits must be consulted)TEMPERATURERANGEPRESSURE 600CF3MCL600CG8MCL600LCCCL600-46 to -29- - -(1)15.919.02018.3- - -(1)41.4-29 to 3820.015.919.02018.349.651.747.2- - 062.777.2177- - -(2)- - -(2)100- - -(2)- - -(2)11.7- - -(2)- - -(2)- - -(2)- - -(2)30.0- - -(2)- - -(2)- - -(2)- - FPsi-50 to -20- - -(1)230275290265- - -(1)600720750695- - -(1)120014401500-20 to 0230175215230185730455560730480145591011201455350- - -(2)- - -(2)- - -(2)- - -(2)170- - -(2)- - -(2)- - -(2)- - -(2)435- - -(2)- - -(2)- - -(2)- - ------825660845---1. Low temperature for these materials limited to -29 C (-20 F).2. Refer to ASME B16.34.14
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 8. Maximum Allowable Shutoff Pressure Drops based on Trim (Bearing and Seal)(Note: Do not exceed the PN or ASME pressure/temperature rating of the valve or mating flanges)VALVE SIZE, DNBEARINGMATERIALBALL SEAL405080100150200250300350500(4)400BarShaft Size, Inches1/25/85/83/43/411-1/41-1/41-1/21-3/4 2-1/8x2 2-1/8 2-1/2-46 to .453.453.453.453.443.45HD Seal(1)-46 to 031.0Flat Metal(2)-73 to ow 535.048.844.7-46 to 28851.750.025.717.5Fisher TCM Plus or UltraPEEK/PTFEHD Seal(1)R30006TEMPERATURERANGE, C2511.010.911.26.145.726.147.527.516.83228 to 427 38.3(3) 37.5(3) 19.3(3) .10Flat Metal(2)-73 to ow 17.306.69-46 to 28851.751.751.735.022.121.822.5High Temp HD Seal(1)HD Seal(1)12.311.412.313.215.013.7228 to 427 38.3(3) 38.3(3) 38.3(3) 26.3(3) 16.5(3) 16.3(3) 16.9(3)9.2(3)8.6(3)9.1611.211.210.2Flat Metal(2)-73 to ow 4.614.613.4HD Seal(1)-46 to 014.0High Temp HD Seal(1)228 to 427---------15.318.718.717.0Flat Metal(2)-73 to ow 324.322.3TEMPERATURERANGE, F11-1/22346101214R30006SilverPlatedHigh Temp HD Seal(1)S31603LNitride38.3(3) 27.6(3) 27.2(3) 28.1(3) 15.4(3) 14.3(3)VALVE SIZE, NPSBEARINGMATERIALBALL SEAL20(4)16Shaft Size, Inches1/25/85/83/43/411-1/41-1/41-1/2-50 to 15015015015015015045050505050505050505050505050HD Seal(1)-50 to 500750750750750750750750593553450384450450Flat Metal(2)-100 to 500---------300300300300150150------------Flow 64899Fisher TCM Plus or UltraPEEK/PTFER300068Psi1-3/4 2-1/8x2 2-1/8 2-1/2HD Seal(1)-50 to 550750725373254160158163898389109109High Temp HD Seal(1)550 to 62(3)67828274Flat Metal(2)-100 to 800---------2461461551548580------------Flow Ring800108072038827315816316188828810610697HD Seal(1)-50 to lverPlatedHigh Temp HD Seal(1)550 to )125(3)133163163148Flat Metal(2)-100 to 800---------300292300300150150------------Flow Ring80015001500776546316326322176164176212212194HD Seal(1)-50 to itrideHigh Temp HD Seal(1)550 to 2272272247Flat Metal(2)-100 to 800---------300300300300150150------------Flow . Pressure drops shown for HD seals are for forward flow only. For reverse flow with HD seal, limit pressure drop to 6.9 bar (100 psig).2. Lubricated service only.3. Consult your Emerson sales office or Local Business Partner if higher pressure drops are required.4. This column is also appropriate for the DN 600x500 (NPS 24x20).15
Product BulletinVee-Ball Valves51.3:Vee-BallMarch 2018D101363X012Table 9. Fisher V150 DimensionsVALVESIZEV150 DIMENSIONS (ISA 12779921007380871315.9 and 15.9 x 12.715.9 and 15.9 x 6.017.572107158350(2)400(2)500600x500NPS38140650
Class VI per ANSI/FCI 70-2 and per IEC 60534-4, Flat Metal Ball Seal for NPS 3 through 12 only (Forward Flow): Class IV per ANSI/FCI 70-2 and per IEC 60534-4, HD (Heavy Duty) Ball Seal (Bidirectional Flow): 0.01% of valve capacity; Class IV per ANSI/FCI 70-2 and IEC 60534-4; Maximum allo
www.Fisher.com D101363X012 Vee-Ball Design V150, V200 and V300 Rotary Control Valves This bulletin covers the 1- through 2-inch, 3- through 12-inch Series B, and the 14- through 20-inch Design V150, V200 and V300 Vee-Ball control valves (shown in figure 1). The Type Vee-Ball valve combines globe valve ruggedness with the efficiency of a rotary .
through 24) V150, V200 and V300 Vee-Ball control valves. The Vee-Ball valve combines globe valve ruggedness with the efficiency of a rotary valve. The Vee-Ball valve is a segmented ball valve which features a contoured segmented V-Notch ball. A shearing action between the V-notch ball and the ball seal (figure 1) promotes smooth, nonclogging .
The V150, V200, and V300 Vee‐Ball valves (figure 1) with a V‐notch ball are used in throttling or on‐off service. The V200 is a flangeless construction. The V150 and V300 valves are raised‐face flanged constructions. The splined valve shaft of all these valves connect to a variety of rotary‐shaft actuators. Specifications
51.3:vee-ball may2012 5 150shown) sealprotector ring flat metal ball seal v-notch ball shims body spring seal seal protector ring hdseal radial seal v-notchball wave spring body sealprotector ring tcm ballseal v-notch ball body backup ring viewa hdmetalballsealdetail viewa .
2 teaspoons Hy-Vee Selects extra virgin olive oil 2 large yellow onions, diced 4 garlic cloves, minced ½ cup Hy-Vee dried cranberries (or raisins) 1 tablespoon Hy-Vee ground cumin 1 tablespoon Hy-Vee ground coriander 1 (15 oz.) can Hy-Vee no-salt-added black beans, drained and rinsed ½ bunch fresh cilantro, chopped Juice of 1 lemon
The Vee–Ball Valve, a Design V150 or V200, is the final control device that controls the amount of process flow. The SKF electrically operated actuator provides rotary motion to open and close the valve. A stepping motor in the actuator drives a ball screw. The linear motion of the
The rugged Vee-Ball valve incorporates large margins of safety in its design. This, coupled with extensive flow testing and evaluation, results in a rotary control valve that is the industry standard for reliability. The Vee-Ball valve’s high capacity and excellent characteristics mean your process can be controlled with
Each reference should include everything you need to identify the item. You need to identify the source type (e.g. book, journal article) and use the correct referencing format from this guide to create the reference. If you include items that are not specifically cited but are relevant to the text or of potential interest to the reader, then that is a bibliography. Generally speaking, the key .
