POP-UP TENT CANOPYINSTALLATION & REMOVALSETUP INSTRUCTIONS
POP-UP TENT CANOPY INSTALLATION & REMOVALTHANK YOU FOR YOUR PURCHASE!If you have questions about installation, maintenance, or take down, please call us at (800)426-9496. Our goalis that you are completely satisﬁed with our products. Please read this installation manual carefully and followall instructions contained herein. Please note that the installer is responsible for the site selection, installationand use. Do not erect during inclement weather and follow all safety procedures during the installation andtake down process.Please contact all utility companies for underground services. In many states, the utilities work together andhave formed a Utility Locating Service. It is your responsibility to locate all the underground services, includingspeaking to the owner about irrigation, pool and other special services that they may have installed. Also,please note that special precautions should be taken such that any overhead powerlines are duly noted andavoided during the tent erection process.TentCraft Inc in no way represents the estimated holding power to be true in all cases. It is anestimate, and as such, does not imply that the ﬁgures are sufﬁcient to hold any tent securely inwindy or adverse weather conditions. The tent installer accepts sole responsibility for the safeinstallation, teardown, and maintenance of any tent. TentCraft does not represent in any way thatthe materials provided with the purchase of the tent are sufﬁcient enough to hold it up in windy oradverse weather conditions. There is no way for TentCraft to know the site conditions or theweather conditions at the event to be able to recommend the adequate amount of holding powerneeded to hold the tent safely in position. Furthermore, we are not responsible for the methodswhich the installer uses to erect the tent or anchor it in position. Installers MUST be empowered todeem the tent unsafe for occupancy if/when the weather becomes unstable. For furtherrecommendations on determining necessary staking values, please consult the IFAI ProceduralHandbook for the Safe Installation and Maintenance of Tentage and the IFAI’s Pullout Capacity ofTent Stakes. These resources are available from the IFAI Tent Rental Division.2
POP-UP TENT CANOPY INSTALLATION & REMOVALStep 1TO INSTALL CANOPY ONTO FRAME:Place your closed tent frame in desired location and expand frame half way.Step 2Drape canopy over partially expanded tent frame, making sure canopycorners are adjacent to tent frame corners.Step 3Connect each canopy corner to corresponding tent frame corner using theVelcro straps. Wrap the straps around the indented top portion of the tentframe corner pole. Straps should sit snug against the tent frame pole.Step 4After connecting all canopy corners to tent frame corners, arrange the peakgrommet atop the center section of the tent frame and attach with providedpeak cap.NOTE: The peak cap will only slide into the center console one way. Makesure the pinhole on the peak cap is positioned correctly before pushing intoplace.3
POP-UP TENT CANOPY INSTALLATION & REMOVALStep 5Conﬁrm peak grommet and canopy corners are properly attached to the tentframe. Expand the tent frame by pulling on opposite sides of the tent framelegs.NOTE: This step may require two people.Step 6Push up the corner connector and click into place. After all corners pieces arelocked into place, use the white loop handles to pull down the bottom edge ofthe canopy. Canopy corners should sit ﬂush against the tent frame cornersand not be bunched.To setup frame for use, continue with pop-up tent assembly instructions.Step 7TO REMOVE CANOPY FROM FRAME:Lower the entire tent structure using the snap button functions on all legs.Adjust to lowest snap button for easy canopy access.Step 8Push down the red button located on the inner corners of the tent frame torelease the canopy. While holding the red button, pull the corner connectorpieces down to release corner tension. Repeat on all four sides.4
POP-UP TENT CANOPY INSTALLATION & REMOVALStep 9Collapse tent frame half way by pushing inward on opposite sides of theframe structure.Step 10Undo the Velcro straps from each canopy corner and lift canopy corners upand over the tent frame corners.Step 11Release the peak cap from the peak grommet. To do this, pull up on the peakcap to reveal the center console section. You will see an arrow labeled“Press.” Using a pen or similar object, insert pressure into the hole to releasethe center console pin. Remove peak cap and set aside.Step 12The peak grommet and canopy corners should now be detached from the tentframe. Remove the entire canopy by lifting and sliding it off the tent frame.Close the tent frame completely by pushing all four corner legs intoeachother.5
the canopy. Canopy corners should sit ﬂush against the tent frame corners and not be bunched. To setup frame for use, continue with pop-up tent assembly instructions. Step 7 TO REMOVE CANOPY FROM FRAME: Lower the entire tent structure using the snap button functions on all legs. Adjust to lowest sn
tent and insert center pole pin into the grom-met at the top of the canopy. With this pin in place, lift and push the pin end skyward and the center pole base toward center of tent to raise the pole and canopy. If your tent has multiple center poles, the first po
the tent and store in a safe area. 6. With the perimeter poles set, walk under the tent and insert center pole pin into the grom-met at the top of the canopy. With this pin in place, lift and push the pin end skyward and the center pole base toward center of tent to raise the pole and canopy. If your tent has multiple cen-
12' x 12' Straight Leg Pop-Up Canopy Assembly Instructions 150 Callender Road Watertown, CT 06795 www.shelterlogic.com 1-800-524-9970 1-800-559-6175 Canada: DeSCrIPtIon MoDeL # 12'x12' Straight Leg Pop-Up - White 22538 12'x12' Straight Leg Pop-Up - Red 22539 12'x12' Straight Leg Pop-Up - Blue 22540 12'x12' Straight Leg Pop-Up - Black 22541
10' x 10' Straight Leg Pop-Up Canopy Assembly Instructions 150 Callender Road Watertown, CT 06795 www.shelterlogic.com 1-800-524-9970 1-800-559-6175 Canada: DeSCrIPtIon MoDeL # 10'x10' Straight Leg Pop-Up - Red 22561 10'x10' Straight Leg Pop-Up - Blue 22562 10'x10' Straight Leg Pop-Up - Green 22563 10'x10' Straight Leg Pop-Up - Desert Bronze 22564
CANOPY TYPE (see images below) CANOPY COLOR HARDWARE CABLE OR STEM LENGTH 5 5" round canopy W White AC Air Craft Cable 18 18 inches 5S 5" square canopy A Aluminum SW Stem white 24 24 inches SCD Square canopy driver box B Black SA Stem aluminum 36 36 inches RCD Round canopy driver box ####
Canopy structure was estimated from discrete return and waveform ALS data. New models were developed based on the Beer-Lambert law to relate canopy volume to the fraction of laser light reaching the ground. Waveform ALS data (canopy volume RMSE 27.6%) described canopy structure better than discrete return ALS data (canopy volume RMSE 36.5%).
- The use of montana tropical forest canopy by bird species 455 Figure 3. The space division layer of forest canopy in use by birds (Pearson 1971) Figure 2. The space division of the tree canopy layer in its use by birds (Pearson 1971). Note: Axis X wide canopy (m); Axis Y canopy height (m); Position I: if the bird occupies the space at the
Plan and monitor animal diet and nutrition LANAnC46 Plan and monitor animal diet and nutrition 1 Overview This standard covers planning and monitoring the diet and nutrition for animals in your care. You will need to identify the nutritional requirements of the animals and develop feeding plans containing all the necessary information for those responsible for feeding the animals. You will .