Badger Metal Deck Hangers
JURISDICTIONAL APPROVALSOSI IPDEDITION 1020
HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (1) BADGER INDUSTRIES MDH NO-DRILLTM HANGER41 2"MIN41 2"MINA3"MAXATR SHALL BE EXPOSEDAT TOP, BUT SHALL NOTCONTACT METAL DECKING538"Ø - 8"Ø ATR TO PROPERHOLE. ONLY ONE ATR SHALLBE INSTALLED PER HANGERAFOR LOCATIONS WHERE MRLCANNOT BE SATISFIED, SEE DETAILM2.121 FOR OPTION WITH (2) MDHHANGERS AND STRUT SPANNERMIN. 20 GA VERCO W3 OR PLW3 STEEL DECKW/ MIN. 3000 PSI NWC OR SLWC. FOR USE INVERCO W2 OR PLW2 DECK, SEE NOTE 4PROJECT APPROVED HANGER,TRAPEZE, OR SEISMIC SUPPORTMRLFOR PROPER INSTALLATION, FLATSURFACE SHALL FACE DOWNBADGER INDUSTRIES MDH NO-DRILLTMHANGER. SEE DETAIL B-OR-THREADED SHAFTWITH CHISEL POINTTORQUE-OFF HEX NUTSminTHREADED BARREL W/LOCK WASHER1" GAP WHENSPACED AT "Smin"CminEND OF CONCRETEFILLED METAL DECKBODYOPM-0043-13FULLY TAPPEDTHROUGH HOLEVIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTSDETAIL BJeffrey Y. KikumotoGRAVITY ONLYGRAVITY & RTICAL LBSLBS10/09/202038A TO 38C20038A TO 38E400350A TO 50C20050A TO 50E400150A TO 50D30050A TO 50G6001600563A TO 63D1234530063A TO minINCHMINENDDIST.CminINCHMDH381226MDH125836SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOT EXCEED THE "GRAVITY ONLY"ALLOWABLE LOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLE ANCHORS TO THE MDH DOESNOT IMPACT THE LISTED MDH CAPACITIES.ONLY THE MDH3812 MAY BE USED IN VERCO W2 OR PLW2 DECK AND SHALL BE USED FOR GRAVITY ONLY LOADS.INSTALLATION: CLEAN METAL DECKING GROOVES TO EXPOSE PLATED DECKING METAL PRIOR TO PLACEMENT OFTHE MDH HANGER. ACCURATELY PLACE MDH HANGER CHISEL POINT ENDS INTO METAL DECKING GROOVES WITHFLAT SURFACE FACING DOWNWARDS AND WITH THE LENGTH OF THE MDH BODY BEING PERPENDICULAR TO THEDECKING GROOVES. WHILE HOLDING THE BODY CHISEL POINT END TIGHT INTO METAL DECKING GROOVE, TIGHTENTORQUE-OFF HEX NUT UNTIL BOTH CHISEL POINT ENDS ARE TIGHT AND SECURELY WEDGED INTO THE OPPOSINGMETAL DECKING GROOVES. WHILE HOLDING THE MDH HANGER BODY IN PLACE, TIGHTEN THE TORQUE-OFF HEX NUTWITH AN OPEN END WRENCH UNTIL THE HEX NUT HAS BROKEN AWAY FROM THE THREADED BARREL, LEAVING THELOCK WASHER COMPRESSED AND THE HEX NUT LOOSE ON THE THREADED SHAFT. FOR REFERENCE, A MINIMUM OF15 FT-LBS OF TORQUE IS REQUIRED FOR THE MDH3812 AND A MINIMUM OF 20 FT-LBS OF TORQUE IS REQUIRED FORTHE MDH1258.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM2.120563 of 846
HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (1) BADGER INDUSTRIES MDH NO-DRILLTM HANGER41 2"MIN41 2"MINBOLT SHALL BE EXPOSED AT TOP, BUTSHALL NOT CONTACT METAL DECKINGL1x1x12GA, 1" LG. ANGLE MAY BEROTATED TO ANY ANGLE IN PLAN21 2"MINA3"MAXMIN. 20 GA VERCO W2, W3,PLW2 OR PLW3 STEEL DECK W/MIN. 3000 PSI NWC OR SLWC38"Ø BOLT W/ ROUND WASHER TOPROPER HOLE. ONLY ONE BOLTSHALL BE INSTALLED PER HANGERAMIN. 12GA ASTM A641 WIRE OR AIRCRAFTCABLE TIED W/ MIN. (4) TWISTS WITHIN11 2", TYP. WIRE OR CABLE HANGERSHALL BE FOR TENSION LOADS ONLY0 -15 FOR PROPER INSTALLATION, FLATSURFACE SHALL FACE DOWNBADGER INDUSTRIES MDH NO-DRILLTMHANGER. SEE DETAIL BGRAVITY A TO DIST.CminINCH1" GAP WHENSPACED AT "Smin"CminOPM-0043-13END OF CONCRETEFILLED METAL DECK26 KikumotoJeffreyY.SEE DETAIL M0.00 FOR SECTION NOTESPROXIMITY OR SPACING OF NEW OR EXISTING CONCRETEINSERTS OR DRILLED HOLE ANCHORS TO THE MDH DOES NOTIMPACT THE LISTED MDH CAPACITIES.INSTALLATION: CLEAN METAL DECKING GROOVES TO EXPOSEPLATED DECKING METAL PRIOR TO PLACEMENT OF THE MDHHANGER. ACCURATELY PLACE MDH HANGER CHISEL POINTENDS INTO METAL DECKING GROOVES WITH FLAT SURFACEFACING DOWNWARDS AND WITH THE LENGTH OF THE MDHBODY BEING PERPENDICULAR TO THE DECKING GROOVES.WHILE HOLDING THE BODY CHISEL POINT END TIGHT INTOMETAL DECKING GROOVE, TIGHTEN TORQUE-OFF HEX NUTUNTIL BOTH CHISEL POINT ENDS ARE TIGHT AND SECURELYWEDGED INTO THE OPPOSING METAL DECKING GROOVES.WHILE HOLDING THE MDH HANGER BODY IN PLACE, TIGHTENTHE TORQUE-OFF HEX NUT WITH AN OPEN END WRENCHUNTIL THE HEX NUT HAS BROKEN AWAY FROM THETHREADED BARREL, LEAVING THE LOCK WASHERCOMPRESSED AND THE HEX NUT LOOSE ON THE THREADEDSHAFT. FOR REFERENCE, A MINIMUM OF 15 FT-LBS OFTORQUE IS REQUIRED FOR THE MDH3812.VIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTS10/09/20203THREADED SHAFTWITH CHISEL POINTTORQUE-OFF HEX NUTTHREADED BARREL W/LOCK WASHERBODYFULLY TAPPEDTHROUGH HOLEDETAIL BMASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM2.120.1564 of 846
HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (2) BADGER INDUSTRIES MDH NO-DRILLTM HANGERS41 2"BOLT SHALL BE EXPOSEDAT TOP, BUT SHALL NOTCONTACT METAL DECKING41 2"538"Ø - 8"Ø BOLT TO PROPERHOLE, TYP. ONLY ONE BOLTSHALL BE INSTALLED PERHANGER. JAM OR HEX NUTNOT REQ'D15 8 x15 8 x12 GA SINGLESTRUT (SOLID, PUNCHED,OR SLOTTED)A3"MIN. 20 GA VERCO W3 ORPLW3 STEEL DECK W/ MIN.3000 PSI NWC OR SLWC1"MAX1"MINTYPFOR PROPER INSTALLATION,FLAT SURFACE SHALL FACEDOWN, TYPEQATHREADED SHAFTWITH CHISEL POINTBADGER INDUSTRIES MDHNO-DRILLTM HANGER, TYP.SEE DETAIL BB-LINE BN200 STRUT NUTEQMIN 3 16x15 8x15 8 ASTM A36 STRUTWASHER AND REG. NUT (SEETABLE FOR TORQUE REQ)6" MIN22" MAX FOR MDH381216" MAX FOR MDH12583VIEW A-ATORQUE-OFF HEX NUT8"TO 3 4" DIA. ATR HANGERTHREADED BARREL W/ LOCK WASHERBODYFULLY TAPPEDTHROUGH HOLEDETAIL BOPM-0043-13GRAVITY ONLYGRAVITY & SEISMICATRALLOWABLEALLOWABLEJeffreyY. 0038A TO 38G60050A TO 50D30050A TO 50G600163A TO 63D30063A TO 63G600538A TO 38F45038A TO 38H900350A TO 50F45050A TO 50H90019005900375A TO 75F123445045063A TO 63H75A TO 75HMINENDDIST.CminINCH26FASTENER WITHSTRUT NUT310/09/2020838A TO 38D63A TO 31428- 34TORQUEREQ'DFT-LBS1950SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOT EXCEED THE "GRAVITY ONLY" ALLOWABLELOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLE ANCHORS TO THE MDH DOES NOT IMPACTTHE LISTED MDH CAPACITIES.INSTALLATION: CLEAN METAL DECKING GROOVES TO EXPOSE PLATED DECKING METAL PRIOR TO PLACEMENT OF THE MDHHANGER. ACCURATELY PLACE MDH HANGER CHISEL POINT ENDS INTO METAL DECKING GROOVES WITH FLAT SURFACE FACINGDOWNWARDS AND WITH THE LENGTH OF THE MDH BODY BEING PERPENDICULAR TO THE DECKING GROOVES. WHILE HOLDINGTHE BODY CHISEL POINT END TIGHT INTO METAL DECKING GROOVE, TIGHTEN TORQUE-OFF HEX NUT UNTIL BOTH CHISEL POINTENDS ARE TIGHT AND SECURELY WEDGED INTO THE OPPOSING METAL DECKING GROOVES. WHILE HOLDING THE MDH HANGERBODY IN PLACE, TIGHTEN THE TORQUE-OFF HEX NUT WITH AN OPEN END WRENCH UNTIL THE HEX NUT HAS BROKEN AWAY FROMTHE THREADED BARREL, LEAVING THE LOCK WASHER COMPRESSED AND THE HEX NUT LOOSE ON THE THREADED SHAFT. FORREFERENCE, A MINIMUM OF 15 FT-LBS OF TORQUE IS REQUIRED FOR THE MDH3812 AND A MINIMUM OF 20 FT-LBS OF TORQUE ISREQUIRED FOR THE MDH1258.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM2.121565 of 846
HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (2) BADGER INDUSTRIES MDH NO-DRILLTM HANGERS41 2"MIN41 2"MINBOLT SHALL BE EXPOSED ATTOP, BUT SHALL NOT CONTACTMETAL DECKING, TYPREG. NUT, TYPA3"MAXMIN 3 16x15 8x15 8 ASTM A36STRUT WASHER, TYPAMIN. 20 GA VERCO W2, W3,PLW2 OR PLW3 STEEL DECK W/MIN. 3000 PSI NWC OR SLWC38"Ø BOLT TO PROPER HOLE, TYP.SNUG TIGHTEN EVENLY UNTIL STRUTMEMBER IS IN CONTACT FLAT TOPLATE WITH STEEL DECKINGFOR PROPER INSTALLATION, FLATSURFACE SHALL FACE DOWN, TYPBADGER INDUSTRIESMDH3812 NO-DRILLTMHANGER, TYP. SEE DETAIL B1"MINTYPEQ15 8 x15 8 x12 GA SINGLE STRUT (SOLID,PUNCHED, OR SLOTTED) MAY BEROTATED TO ANY ANGLE IN PLANEQB-LINE BN200 STRUT NUT24"MAXMIN 3 16x15 8x15 8 ASTM A36 STRUT WASHERAND REG. NUT (SEE TABLE FOR TORQUE REQ)3THREADED SHAFTWITH CHISEL POINTTORQUE-OFF HEX NUTTHREADED BARREL W/ LOCK WASHEROPM-0043-13BODYFULLY TAPPEDTHROUGH HOLE1234TO 3 4" DIA. ATR HANGERSmin1" GAP WHENSPACED AT "Smin"CminEND OF CONCRETEFILLED METAL DECKJeffrey Y. KikumotoVIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTSDETAIL B10/09/2020GRAVITY & SEISMICGRAVITY CAL LBSLBS38A TO 38E40038A TO 38G690350A TO 50E40050A TO 50G6901690563A TO 63E8"40063A TO 38122682FASTENER WITHSTRUT NUTDIA.INCH31828- 34TORQUEREQ'DFT-LBS1950SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOT EXCEED THE "GRAVITY ONLY" ALLOWABLELOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLE ANCHORS TO THE MDH DOES NOT IMPACTTHE LISTED MDH CAPACITIES.INSTALLATION: CLEAN METAL DECKING GROOVES TO EXPOSE PLATED DECKING METAL PRIOR TO PLACEMENT OF THE MDHHANGER. ACCURATELY PLACE MDH HANGER CHISEL POINT ENDS INTO METAL DECKING GROOVES WITH FLAT SURFACE FACINGDOWNWARDS AND WITH THE LENGTH OF THE MDH BODY BEING PERPENDICULAR TO THE DECKING GROOVES. WHILE HOLDINGTHE BODY CHISEL POINT END TIGHT INTO METAL DECKING GROOVE, TIGHTEN TORQUE-OFF HEX NUT UNTIL BOTH CHISEL POINTENDS ARE TIGHT AND SECURELY WEDGED INTO THE OPPOSING METAL DECKING GROOVES. WHILE HOLDING THE MDH HANGERBODY IN PLACE, TIGHTEN THE TORQUE-OFF HEX NUT WITH AN OPEN END WRENCH UNTIL THE HEX NUT HAS BROKEN AWAY FROMTHE THREADED BARREL, LEAVING THE LOCK WASHER COMPRESSED AND THE HEX NUT LOOSE ON THE THREADED SHAFT. FORREFERENCE, A MINIMUM OF 15 FT-LBS OF TORQUE IS REQUIRED FOR THE MDH3812.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM2.122566 of 846
ATR HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (1) BADGER INDUSTRIES NDH38FV-W3 NO-DRILLTM HANGER41 2"TYPAA3"L1x1x12GA, 1" LG. ANGLEMAY BE ROTATED TOANY ANGLE IN PLANMIN. 20 GA VERCO W3 OR PLW3 STEELDECK W/ MIN. 3000 PSI NWC OR SLWCBADGER INDUSTRIES NDH38FV-W3NO-DRILLTM HANGER, TYP0 -15 MIN. 12GA ASTM A641 WIREOR AIRCRAFT CABLE TIEDW/ MIN. (4) TWISTS WITHIN11 2". WIRE OR CABLEHANGER SHALL BE FORTENSION LOADS ONLY38" DIA. ATR, TYP. ATR TO BE VISIBLEIN SWIVEL NUT INSPECTION HOLE.JAM OR HEX NUT NOT REQ'DREG. OR REDUCING COUPLINGNUT FOR LARGER SIZE THREADEDRODS ARE PERMITTED38"TO 1 2" DIA. ATR HANGEROPM-0043-13SminNO GAP WHENSPACED AT "Smin"CminJeffrey Y. KikumotoEND OF CONCRETEFILLED METAL DECKVIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTS10/09/2020GRAVITY & SEISMICGRAVITY RTICAL HANGER HTYPETYPELBSLBS38A TO 38A50A TO 50A123707038A TO 38D50A TO 50D170317018221 211 2111 222SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOTEXCEED THE "GRAVITY ONLY" ALLOWABLE LOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLEANCHORS TO THE NDH DOES NOT IMPACT THE LISTED NDH CAPACITIES.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, Jiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM3.20575 of 846
ATR HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (2) BADGER INDUSTRIES NDH38FV-W3 NO-DRILLTM HANGERSWHEN INSTALLED PARALLEL TO FLUTE,STRUT SHALL BE INSTALLED OVER SWIVELNUTS AND SNUG TIGHT TO BOTH HANGERS41 2"TYPAA3"BADGER INDUSTRIES NDH38FV-W3NO- DRILLTM HANGER, TYP38"MIN. 20 GA VERCO W3 ORPLW3 STEEL DECK W/ MIN.3000 PSI NWC OR SLWCDIA. ATR, TYP. ATR TO BE VISIBLEIN SWIVEL NUT INSPECTION HOLE.SOLID, PUNCHED, ORSLOTTED STRUT MEMBERMIN 3 16x15 8x15 8 ASTM A36 STRUTWASHER AND REG. NUT, T&B, TYP.SNUG TIGHTEN NUTS EVENLY UNTILSTRUT MEMBER IS IN CONTACT FLATTO FLAT WITH STEEL DECKINGB-LINE BN200 STRUT NUT1"MINTYPEND OF CONCRETEFILLED METAL DECKVIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTSSTRUT MEMBER SIZE516"x1 8"x12GASINGLE STRUT15 8"x15 8"x12GASINGLE STRUT234EQ312" MIN24" MAX38"TO 5 8" DIA. ATR HANGERFASTENER WITHSTRUT NUTNO GAP WHENSPACED AT "Smin"Jeffrey Y. KikumotoCmin1EQOPM-0043-13Smin13MIN 3 16x15 8x15 8 ASTM A36STRUT WASHER AND REG.NUT (SEE TABLE FORTORQUE - 58GRAVITY & SEISMICGRAVITY RTICAL HANGER HTYPETYPELBSLBS38A TO 38A11038A TO 38C220350A TO 50A11050A TO 50C220163A TO 63A11063A TO 63C220538A TO 38A11038A TO 38D300350A TO 50A11050A TO 50D300163A TO 63A11063A TO 63D300550MINENDDIST.CminINCH821 211 2221 211 2821 211 2821 211 2221 211 2821 211 2SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOT EXCEED THE "GRAVITY ONLY"ALLOWABLE LOAD.MINIMUM SPACING REQUIREMENT DOES NOT APPLY WHEN STRUT IS INSTALLED PARALLEL TO FLUTE.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLE ANCHORS TO THE NDH DOESNOT IMPACT THE LISTED NDH CAPACITIES.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM3.21576 of 846
ATR HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (1) BADGER INDUSTRIES NDH4S-W3 NO-DRILLTM HANGER41 2"TYP3"AASmin(SAMEFLUTE)MIN. 20 GA VERCO W3 OR PLW3 STEELDECK W/ MIN. 3000 PSI NWC OR SLWCTIGHTEN SET BOLTS ASSTATED IN NOTE 4 BELOWCminBADGER INDUSTRIES NDH4S-W3NO-DRILLTM HANGERNO GAP WHEN SPACEDAT Smin 21 4"3TO 5 8" DIA. ATR HANGER IN CORRESPONDINGHOLE W/ 12" MIN ENGAGEMENT. ATR CONTACTWITH STEEL DECKING SHALL NOT EXCEED SNUGTIGHT. JAM OR HEX NUT NOT REQ'DEND OF CONCRETEFILLED METAL DECKVIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTS8"GRAVITY ONLYGRAVITY & LVERTICAL HANGER HTYPETYPELBSLBSOPM-0043-13123438A TO 38F47038A TO 38J940350A TO 50F47050A TO 50J940163A TO 63F470Jeffrey94063ATO 63J Y. Kikumoto538A TO 38F57038A TO 38K1140350A TO 50F57050A TO 50K1140163A TO 63F57063A TO 63K38A TO 38G63038A TO 38L1260350A TO 50G63050A TO 50L1260163A TO 63G63063A TO 63L1260538A TO 38H73038A TO 38L1460350A TO 50H73050A TO 50L1460163A TO 63H73063A TO 63L1460510/30/202011405MINENDDIST.CminINCH8221 4666106141 268828828828SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOTEXCEED THE "GRAVITY ONLY" ALLOWABLE LOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLEANCHORS TO THE NDH DOES NOT IMPACT THE LISTED NDH CAPACITIES.INSTALLATION: ALIGN THE LENGTH OF THE NDH4S-W3 TO BE PERPENDICULAR TO THELENGTH OF THE STEEL DECKING GROOVES. WHILE HOLDING THE NDH4S-W3 IN PLACE,HAND TIGHTEN EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY MAKING SURETHAT THE POINTED END OF EACH SET BOLT IS ENGAGED INTO THE STEEL DECKINGGROOVE. ONCE EACH OF THE (4) SET BOLTS ARE HAND TIGHT AND PROPER PLACEMENTOF THE NDH4S-W3 HAS BEEN CHECKED, CONTINUE TIGHTENING (USING A BOX ENDWRENCH) EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY UNTIL THE HEXHEAD OF EACH SET BOLT BREAKS AWAY. PROPER INSTALLATION REQUIRES THE HEXHEADS OF ALL SET BOLTS TO HAVE BROKEN AWAY. FOR REFERENCE, A MINIMUM OF 10FT-LBS OF TORQUE IS REQUIRED.PAGEMASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/30/2020Jiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM3.30Page 577 of 846
ATR HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (2) BADGER INDUSTRIES NDH4S-W3 NO-DRILLTM HANGERS41 2"TYP3"AMIN. 20 GA VERCO W3 ORPLW3 STEEL DECK W/ MIN.3000 PSI NWC OR SLWCATIGHTEN SET BOLTS ASSTATED IN NOTE 5 BELOWBADGER INDUSTRIES NDH4S-W3NO-DRILLTM HANGER, TYPB-LINE BN200 STRUT NUTMIN 3 16x15 8x15 8 ASTM A36STRUT WASHER AND REG.NUT, TYP (SNUG TIGHT)152" TO 8" DIA. ATR INCORRESPONDING HOLE W/ 1 2"MIN ENGAGEMENT, TYP. ATRCONTACT WITH STEEL DECKINGSHALL NOT EXCEED SNUG TIGHTSOLID, PUNCHED, ORSLOTTED STRUT MEMBERMIN 3 16x15 8x15 8 ASTM A36STRUT WASHER AND REG. NUT(SEE TABLE FOR TORQUE REQ)2"MAXEQ1"MINTYP38"TO 3 4" DIA. ATR HANGEREQ10" MIN14" MAX4VIEW A-AOPM-0043-13STRUT MEMBER SIZE13516"x1 8"x12GASINGLE STRUT15 8"x15 8"x12GASINGLE STRUT551 8"x1 8"x12GASOLID DOUBLE STRUT12345GRAVITY & SEISMICGRAVITY CAL HANGERJeffrey Y. PELBSLBS38A TO 38E38038A TO 38E38010/09/202050A TO 50E38050A TO 50E3380163A TO 63E38063A TO 63E380538A TO 38H73038A TO 38K1180350A TO 50J90050A TO 50K1180163A TO 63J90063A TO 63K1180563A TO 63J90063A TO 63N240052400375A TO 75J90075A TO 75NMINENDDIST.CminINCH8626868626868646FASTENER WITHSTRUT NUTDIA.INCH3128- 34TORQUEREQ'DFT-LBS1950SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALL NOT EXCEED THE "GRAVITY ONLY" ALLOWABLELOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLE ANCHORS TO THE NDH DOES NOT IMPACT THELISTED NDH CAPACITIES.NDH HANGER ASSEMBLY SHALL BE SPACED 10" MIN. FROM ANY ADJACENT NDH HANGERS. REFER TO DETAIL M3.30 FOR SPACINGDETAIL.INSTALLATION: ALIGN THE LENGTH OF THE NDH4S-W3 TO BE PERPENDICULAR TO THE LENGTH OF THE STEEL DECKING GROOVES.WHILE HOLDING THE NDH4S-W3 IN PLACE, HAND TIGHTEN EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY MAKING SURETHAT THE POINTED END OF EACH SET BOLT IS ENGAGED INTO THE STEEL DECKING GROOVE. ONCE EACH OF THE (4) SET BOLTSARE HAND TIGHT AND PROPER PLACEMENT OF THE NDH4S-W3 HAS BEEN CHECKED, CONTINUE TIGHTENING (USING A BOX ENDWRENCH) EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY UNTIL THE HEX HEAD OF EACH SET BOLT BREAKS AWAY.PROPER INSTALLATION REQUIRES THE HEX HEADS OF ALL SET BOLTS TO HAVE BROKEN AWAY. FOR REFERENCE, A MINIMUM OF 10FT-LBS OF TORQUE IS REQUIRED.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM3.31578 of 846
ATR HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (2) BADGER INDUSTRIES NDH4S-W3 NO-DRILLTM HANGERS41 2"TYP3"BADGER INDUSTRIES NDH4S-W3NO-DRILLTM HANGER, TYPAMIN. 20 GA VERCO W3 ORPLW3 STEEL DECK W/ MIN.3000 PSI NWC OR SLWCTIGHTEN SET BOLTS ASSTATED IN NOTE 5 BELOW, TYPAREG. NUT (SNUG TIGHT), TYP58" DIA. ATR IN CORRESPONDINGHOLE W/ 1 2" MIN ENGAGEMENT, TYP.ATR CONTACT WITH STEEL DECKINGSHALL NOT EXCEED SNUG TIGHTREG. OR REDUCING COUPLING NUTFOR LARGER OR SMALLER SIZETHREADED RODS ARE PERMITTEDEQMW-SAP-200-BSEE PAGE X6.05EQ38"TO 7 8" DIA. ATR HANGER12"8"DIA. ATR W/ REG.NUT, T&B (SNUG TIGHT)VIEW A-AOPM-0043-13GRAVITY ONLYGRAVITY & SEISMICATRALLOWABLEALLOWABLEHANGERHANGERVERTICAL JeffreyVERTICAL HANGERY. PELBSLBS12345193010/09/2020338A TO 38H73038A TO 38M50A TO 50L126050A TO 50M1930163A TO 63L126063A TO 63M1930575A TO 75L126075A TO 75M1930388A TO 88A126088A TO 88M19307MINENDDIST.CminINCH8626864686SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALLNOT EXCEED THE "GRAVITY ONLY" ALLOWABLE LOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLEDHOLE ANCHORS TO THE NDH DOES NOT IMPACT THE LISTED NDH CAPACITIES.NDH HANGER ASSEMBLY SHALL BE SPACED 10" MIN. FROM ANY ADJACENT NDHHANGERS. REFER TO DETAIL M3.30 FOR SPACING DETAIL.INSTALLATION: ALIGN THE LENGTH OF THE NDH4S-W3 TO BE PERPENDICULARTO THE LENGTH OF THE STEEL DECKING GROOVES. WHILE HOLDING THENDH4S-W3 IN PLACE, HAND TIGHTEN EACH OF THE (4) SET BOLTS EQUALLY ANDALTERNATIVELY MAKING SURE THAT THE POINTED END OF EACH SET BOLT ISENGAGED INTO THE STEEL DECKING GROOVE. ONCE EACH OF THE (4) SETBOLTS ARE HAND TIGHT AND PROPER PLACEMENT OF THE NDH4S-W3 HAS BEENCHECKED, CONTINUE TIGHTENING (USING A BOX END WRENCH) EACH OF THE (4)SET BOLTS EQUALLY AND ALTERNATIVELY UNTIL THE HEX HEAD OF EACH SETBOLT BREAKS AWAY. PROPER INSTALLATION REQUIRES THE HEX HEADS OFALL SET BOLTS TO HAVE BROKEN AWAY. FOR REFERENCE, A MINIMUM OF 10FT-LBS OF TORQUE IS REQUIRED.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM3.32579 of 846
ATR HANGER ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (4) BADGER INDUSTRIES NDH4S-W3 NO-DRILLTM HANGERS41 2"TYP3"BADGER INDUSTRIES NDH4S-W3NO-DRILLTM HANGER, TYPAMIN. 20 GA VERCO W3 ORPLW3 STEEL DECK W/ MIN.3000 PSI NWC OR SLWCTIGHTEN SET BOLTS ASSTATED IN NOTE 5 BELOW, TYPAREG. NUT (SNUG TIGHT), TYP58" DIA. ATR IN CORRESPONDINGHOLE W/ 1 2" MIN ENGAGEMENT, TYP.ATR CONTACT WITH STEEL DECKINGSHALL NOT EXCEED SNUG TIGHTREG. OR REDUCING COUPLING NUTFOR LARGER OR SMALLER SIZETHREADED RODS ARE PERMITTEDEQMW-SAP-400-B FOR 5 8"Ø ATRMW-SAP-400-C FOR 3 4"Ø ATRMW-SAP-400-D FOR 1"Ø ATRSEE PAGE X6.0EQ12"TO 11 4" DIA. ATR HANGER12"ATR W/ REG. NUT, T&B(SNUG TIGHT)VIEW A-AGRAVITY & SEISMICGRAVITY CAL HANGERDIA.CONNECTIONCONNECTIONLOADLOADJeffrey Y. ST.CminINCH50A TO 50L135050A TO 50Q3600163A TO 63N216063A TO 63Q3600575A TO 75P252075A TO 75Q3500388A TO 88P252088A TO 88Q35007100A TO 100P2520100A TO 100Q350016125A TO 125P2520125A TO 125Q350011 4610/09/202026864686SEE DETAIL M0.00 FOR SECTION NOTESWHEN USED FOR "GRAVITY & SEISMIC" LOADING, THE GRAVITY DEMAND SHALLNOT EXCEED THE "GRAVITY ONLY" ALLOWABLE LOAD.PROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLEDHOLE ANCHORS TO THE NDH DOES NOT IMPACT THE LISTED NDH CAPACITIES.NDH HANGER ASSEMBLY SHALL BE SPACED 10" MIN. FROM ANY ADJACENT NDHHANGERS. REFER TO DETAIL M3.30 FOR SPACING DETAIL.INSTALLATION: ALIGN THE LENGTH OF THE NDH4S-W3 TO BE PERPENDICULARTO THE LENGTH OF THE STEEL DECKING GROOVES. WHILE HOLDING THENDH4S-W3 IN PLACE, HAND TIGHTEN EACH OF THE (4) SET BOLTS EQUALLY ANDALTERNATIVELY MAKING SURE THAT THE POINTED END OF EACH SET BOLT ISENGAGED INTO THE STEEL DECKING GROOVE. ONCE EACH OF THE (4) SETBOLTS ARE HAND TIGHT AND PROPER PLACEMENT OF THE NDH4S-W3 HAS BEENCHECKED, CONTINUE TIGHTENING (USING A BOX END WRENCH) EACH OF THE (4)SET BOLTS EQUALLY AND ALTERNATIVELY UNTIL THE HEX HEAD OF EACH SETBOLT BREAKS AWAY. PROPER INSTALLATION REQUIRES THE HEX HEADS OFALL SET BOLTS TO HAVE BROKEN AWAY. FOR REFERENCE, A MINIMUM OF 10FT-LBS OF TORQUE IS REQUIRED.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoM3.33580 of 846
WIRE/CABLE BRACE ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (1) BADGER INDUSTRIES MDH NO-DRILLTM HANGER412"MIN412"MINBOLT SHALL BE EXPOSED AT TOP, BUTSHALL NOT CONTACT METAL DECKINGL1x1x12GA, 1" LG. ANGLE MAY BEROTATED TO ANY ANGLE IN PLANA3"MAXMIN. 12GA ASTM A641 WIRE OR AIRCRAFTCABLE TIED W/ MIN. (4) TWISTS WITHIN11 2", TYP. WIRE OR CABLE HANGERSHALL BE FOR TENSION LOADS ONLYAMIN. 20 GA VERCO W2, W3,PLW2 OR PLW3 STEEL DECK W/MIN. 3000 PSI NWC OR SLWCqFpFOR PROPER INSTALLATION, FLATSURFACE SHALL FACE DOWNBADGER INDUSTRIES MDH NO-DRILLTMHANGER. SEE DETAIL B38"Ø BOLT TO PROPER HOLE. ONLY ONEBOLT SHALL BE INSTALLED PER XLATERALBRACELOADRANGEFpqLBS38A TO 38B13030 - 45 38A TO 38A9046 - 60 OPM-0043-13MINMDHSIZEMDH38121" GAP WHENSPACED AT "Smin"CminMINENDSPACING DIST.SminCminJeffreyY.KikumotoINCHINCHEND OF CONCRETEFILLED METAL DECKVIEW A-A610/09/20202SEE DETAIL N0.00 FOR SECTION NOTESPROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS ORDRILLED HOLE ANCHORS TO THE MDH DOES NOT IMPACT THE LISTEDMDH CAPACITIES.INSTALLATION: CLEAN METAL DECKING GROOVES TO EXPOSE PLATEDDECKING METAL PRIOR TO PLACEMENT OF THE MDH HANGER.ACCURATELY PLACE MDH HANGER CHISEL POINT ENDS INTO METALDECKING GROOVES WITH FLAT SURFACE FACING DOWNWARDS ANDWITH THE LENGTH OF THE MDH BODY BEING PERPENDICULAR TO THEDECKING GROOVES. WHILE HOLDING THE BODY CHISEL POINT ENDTIGHT INTO METAL DECKING GROOVE, TIGHTEN TORQUE-OFF HEX NUTUNTIL BOTH CHISEL POINT ENDS ARE TIGHT AND SECURELY WEDGEDINTO THE OPPOSING METAL DECKING GROOVES. WHILE HOLDING THEMDH HANGER BODY IN PLACE, TIGHTEN THE TORQUE-OFF HEX NUTWITH AN OPEN END WRENCH UNTIL THE HEX NUT HAS BROKEN AWAYFROM THE THREADED BARREL, LEAVING THE LOCK WASHERCOMPRESSED AND THE HEX NUT LOOSE ON THE THREADED SHAFT.FOR REFERENCE, A MINIMUM OF 15 FT-LBS OF TORQUE IS REQUIREDFOR THE MDH3812.THREADED SHAFTWITH CHISEL POINTTORQUE-OFF HEX NUTTHREADED BARREL W/LOCK WASHERBODYFULLY TAPPEDTHROUGH HOLEDETAIL BMASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, www.masonwest.com10/09/2020PAGEJiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoN2.120.1721 of 846
SEISMIC BRACKET ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (1) BADGER INDUSTRIES NDH4S-W3 NO-DRILLTM HANGER41 2"TYP3"AAMIN. 20 GA VERCO W3 OR PLW3 STEELDECK W/ MIN. 3000 PSI NWC OR SLWCqTIGHTEN SET BOLTS ASSTATED IN NOTE 5 BELOWFpBADGER INDUSTRIES NDH4S-W3NO-DRILLTM HANGERSmin(SAMEFLUTE)112"Ø ATR & REG. NUT W/ 2" MINENGAGEMENT. (SNUG TIGHT) THREADSSHALL NOT CONTACT STEEL DECKINGMASON IND. N.Y. SEISMIC BRACKETFOR SOLID OR CABLE BRACING.BRACE BRACKET MAY BE ROTATEDTO ANY ANGLE AROUND ATRCminEND OF CONCRETEFILLED METAL DECKOPM-0043-13VIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTSJeffrey Y. KikumotoΩ0 BLEMINMAXBRACELATERALLATERALBRACE TYPELBSLBS10/09/202050A TO 50J91050A TO 50F55030 - 45 50A TO 50J91050A TO 50F55046 - 60 2412SEE DETAIL N0.00 FOR SECTION NOTESOVERSTRENGTH FACTOR AS REQUIRED FOR ANCHORAGE TO CONCRETEPROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLEANCHORS TO THE NDH DOES NOT IMPACT THE LISTED NDH CAPACITIES.FOR NDH HANGERS WITH SPACING LESS THAN Smin, THE COMBINED DEMAND OFMULTIPLE NDH HANGERS SHALL NOT EXCEED THE CAPACITY OF A SINGLE NDH HANGER.INSTALLATION: ALIGN THE LENGTH OF THE NDH4S-W3 TO BE PERPENDICULAR TO THELENGTH OF THE STEEL DECKING GROOVES. WHILE HOLDING THE NDH4S-W3 IN PLACE,HAND TIGHTEN EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY MAKINGSURE THAT THE POINTED END OF EACH SET BOLT IS ENGAGED INTO THE STEEL DECKINGGROOVE. ONCE EACH OF THE (4) SET BOLTS ARE HAND TIGHT AND PROPER PLACEMENTOF THE NDH4S-W3 HAS BEEN CHECKED, CONTINUE TIGHTENING (USING A BOX ENDWRENCH) EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY UNTIL THE HEXHEAD OF EACH SET BOLT BREAKS AWAY. PROPER INSTALLATION REQUIRES THE HEXHEADS OF ALL SET BOLTS TO HAVE BROKEN AWAY. FOR REFERENCE, A MINIMUM OF 10FT-LBS OF TORQUE IS REQUIRED.MASON WEST, INC.1601 E. Miraloma Ave. Placentia, CA 92870TEL (714) 630 - 0701, Jiefu "Jeff" Zhang, SECalifornia SE No. S5270OPM-0043-13: Reviewed for Code Compliance by Jeffrey KikumotoN3.30728 of 846
SEISMIC BRACKET ATTACHMENTTO CONCRETE FILLED METAL DECKWITH (2) BADGER INDUSTRIES NDH4S-W3 NO-DRILLTM HANGER41 2"TYP3"MIN. 20 GA VERCO W3 OR PLW3 STEELDECK W/ MIN. 3000 PSI NWC OR SLWCAATIGHTEN SET BOLTS ASSTATED IN NOTE 5 BELOW, TYPBADGER INDUSTRIES NDH4S-W3NO-DRILLTM HANGER, TYPqFpREG. NUT, SNUG TIGHT, TYPSmin(SAMEFLUTE)EQ58" DIA. ATR IN CORRESPONDINGHOLE W/ 1 2" MIN ENGAGEMENT, TYP.ATR CONTACT WITH STEEL DECKINGSHALL NOT EXCEED SNUG TIGHTEQ12"MW-SAP-200-BSEE PAGE X6.058" DIA. ASTM A307 BOLT& NUT, SNUG TIGHTCminMASON IND. N.Y. SEISMIC BRACKETFOR SOLID OR CABLE BRACING.BRACE BRACKET MAY BE ROTATEDTO ANY ANGLE AROUND BOLTEND OF CONCRETEFILLED METAL DECKOPM-0043-13VIEW A-A:INSTALLATION OF MULTIPLE INDEPENDENT SUPPORTSJeffrey Y. KikumotoΩ0 BLEMINMAXBRACELATERALLATERALBRACE TYPELBSLBS10/09/202063A TO 63M183063A TO 63K110030 - 45 63A TO 63K111063A TO 63K110046 - 60 2412SEE DETAIL N0.00 FOR SECTION NOTESOVERSTRENGTH FACTOR AS REQUIRED FOR ANCHORAGE TO CONCRETEPROXIMITY OR SPACING OF NEW OR EXISTING CONCRETE INSERTS OR DRILLED HOLEANCHORS TO THE NDH DOES NOT IMPACT THE LISTED NDH CAPACITIES.FOR NDH HANGERS WITH SPACING LESS THAN Smin, THE COMBINED DEMAND OFMULTIPLE NDH HANGERS SHALL NOT EXCEED THE CAPACITY OF A SINGLE NDH HANGER.INSTALLATION: ALIGN THE LENGTH OF THE NDH4S-W3 TO BE PERPENDICULAR TO THELENGTH OF THE STEEL DECKING GROOVES. WHILE HOLDING THE NDH4S-W3 IN PLACE,HAND TIGHTEN EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY MAKINGSURE THAT THE POINTED END OF EACH SET BOLT IS ENGAGED INTO THE STEEL DECKINGGROOVE. ONCE EACH OF THE (4) SET BOLTS ARE HAND TIGHT AND PROPER PLACEMENTOF THE NDH4S-W3 HAS BEEN CHECKED, CONTINUE TIGHTENING (USING A BOX ENDWRENCH) EACH OF THE (4) SET BOLTS EQUALLY AND ALTERNATIVELY UNTIL THE HEXHEAD OF EACH SET BOLT BREAKS AWAY. PROPER INSTALLATION REQUIRES THE HEXHEADS OF ALL SET BOLTS TO HAVE BROKEN AWAY. FOR REFERENCE, A MINIMUM OF 10FT-LBS OF TORQUE IS REQ
4 only the mdh3812 may be used in verco w2 or plw2 deck and shall be used for gravity only loads. 5 installation: clean metal decking grooves to expose plated decking metal prior to placement of the mdh hanger. accurately place mdh hange
ROYAL BABIES AND TOTS NURSERY FLOWRIDER DECK 11 DECK 10 DECK 9 DECK 8 DECK 7 DECK 6 DECK 5 DECK 4 DECK 3 DECK 2 Navigator of the Seas PROFILE 1723 - Starts April 27, 2017 DECK 13 DECK 12 DECK 15 DECK 14 OCEAN VIEW H I Ocean View Stateroom Two twin beds that convert to Royal
NOrwegiaN ePiC Category Descriptions Deck Plans Staterooms DECK 17 DECK 15 DECK 13 DECK 11 DECK 7 DECK 9 DECK 5 EPICPROFILE DECK 18 DECK 16 DECK 14 DECK 12 DECK 10 DECK 6 DECK 8 DECK 19 Built 2010 gross Tonnage: 153,000 Overall Length: 1,080 feet Beam: 133 feet Draft: 28.5 feet engines: Diesel Electric Cruise Speed: 22 knots
Oasis of the Seas DECK 18 DECK 17 DECK 16 DECK 15 DECK 14DECK 12 Last Update: April 21, 2014Profile 1688 - starts May 1, 2016 DECK THREE ON PUBLIC AREAS Opal Theater The state of the art theater features our award winning Broadway-style theater productions and aerial acts. Studio B A multipurpose studio complex filled with activity all day long.
badger is one of the largest; the American badger, the hog badger and the honey badger are generally a little smaller and lighter. The stink badgers are smaller still, and the ferret badgers are the smallest of all. They weigh around 9.1–11 kg (20–24 lb) on average,
3. Joist Hangers. In this confi guration, joist hangers are either face-mounted to a vertical fl at surface, or (more commonly) tabs from the hangers are attached to the top of a beam, wall, or header. Super Stud provides two types of top-mount joist hangers: bridle-style top mount hangers
Spring Hangers followed their own evolution. As in the case of mountings, early spring hangers had very stiff, tall, unstable springs and it was not unusual to sell hangers with 0.375"(10mm) deflection. Spring Hangers contained no rubber for high frequencies and the first improvement was the introduction of a rubber washer. This was
Press the DECK A / DECK C or DECK B / DECK D buttons to switch the left or right TWITCH decks to control the additional 2 Traktor decks. When DECK A / DECK C button is pressed and the LED is lit, all deck controls, touch strip, pads, EQ, fi lters and volume faders on the left of TWITCH will now be controlling Deck C (rather than Deck A).
pool deck 7 miami beach pool deck 16 metropolitan theater deck 6 & 7 kids’ clubs deck 18 msc yacht club deck 16-18-19 seashore restaurant deck 5 ipanema restaurant deck 6 msc sports arena deck 20 jungle pool lounge with sliding roof deck 18 virtual games a
