Power Meter Centrale De Mesure Central De Medida PM820
Power MeterCentrale de mesureCentral de medidaPM820Reference manualManual de référenceManual de referenciaRetain for future use.
NOTICERead these instructions carefully and look at the equipment to becomefamiliar with the device before trying to install, operate, service, ormaintain it. The following special messages may appear throughout thisbulletin or on the equipment to warn of potential hazards or to callattention to information that clarifies or simplifies a procedure.The addition of either symbol to a “Danger” or “Warning” safety labelindicates that an electrical hazard exists which will result in personalinjury if the instructions are not followed.This is the safety alert symbol. It is used to alert you to potential personalinjury hazards. Obey all safety messages that follow this symbol to avoidpossible injury or death.DANGERDANGER indicates an immediately hazardous situation which, if not avoided,will result in death or serious injury.WARNINGWARNING indicates a potentially hazardous situation which, if not avoided, canresult in death or serious injury.CAUTIONCAUTION indicates a potentially hazardous situation which, if not avoided, canresult in minor or moderate injury.CAUTIONCAUTION, used without the safety alert symbol, indicates a potentiallyhazardous situation which, if not avoided, can result in property damage.NOTE: Provides additional information to clarify or simplify a procedure.PLEASE NOTEElectrical equipment should be installed, operated, serviced, andmaintained only by qualified personnel. No responsibility is assumed bySquare D for any consequences arising out of the use of this manual. 2002 Schneider Electric All Rights Reservedi
CLASS A FCC STATEMENTThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures: Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.ii 2002 Schneider Electric All Rights Reserved
Table of ContentsTABLE OF CONTENTSTABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IIIINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1What is the Power Meter? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Meter Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Meter Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Topics Not Covered in this Bulletin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1233444SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Operating the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9How the Buttons Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Changing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Set Up the Power Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Set Up Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Set Up the Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Set Up the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Set Up the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Set Up CTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Set Up PTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Set Up the Meter System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Set Up Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Set Up I/Os . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Set Up the Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Set Up the Alarm Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Advanced Power Meter Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Set Up the Phase Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Set Up the Incremental Energy Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Set Up the THD Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Set Up the VAR/PF Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Set Up the Lock Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Power Meter Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22View the Meter Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Check the Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Read and Write Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23METERING CAPABILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Real-Time Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2003 Schneider ElectricAll Rights Reservediii
Table of ContentsMin/Max Values for Real-time Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Factor Min/Max Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Factor Sign Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Demand Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Demand Power Calculation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Block Interval Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Synchronized Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Thermal Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Demand Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Predicted Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Peak Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Generic Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Energy Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Analysis Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2627293031313435353636373841INPUT/OUTPUT CAPABILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Demand Synch Pulse Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Relay Output Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solid-state KY Pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-wire Pulse Initiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Calculating the Kilowatthour-Per-Pulse Value . . . . . . . . . . . . . . . . . . . . . . . . . . .454647515253ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55About Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Alarm Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Setpoint-driven Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Priorities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Custom Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Types of Setpoint-controlled Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Scale Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Scaling Alarm Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Alarm Conditions and Alarm Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .555556585859626465LOGGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Memory Allocation for Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Alarm Log Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Data Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Alarm-driven Data Log Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Billing Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintenance Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7171727272737374MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77iv 2003 Schneider ElectricAll Rights Reserved
Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Meter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Identifying the Firmware Version, Model, and Serial Number . . . . . . . . . . . . . . . .Viewing the Display in Different Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Getting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .777778787980POWER METER REGISTER LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83About Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .How Power Factor is Stored in the Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .How Date and Time are Stored in Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . .Register List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83838485USING THE COMMAND INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Overview of the Command Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issuing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I/O Point Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operating Outputs from the Command Interface . . . . . . . . . . . . . . . . . . . . . . . .Using the Command Interface to Change Configuration Registers . . . . . . . . . .Conditional Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Command Interface Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Digital Input Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Incremental Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Using Incremental Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Setting Up Individual Harmonic Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . .Changing Scale Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147148151152152153154155156157159160INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 2003 Schneider ElectricAll Rights Reservedv
Table of Contentsvi 2003 Schneider ElectricAll Rights Reserved
1IntroductionWhat is the Power Meter?INTRODUCTIONWhat is thePower Meter?The power meter is a multifunction, digitalinstrumentation, data acquisition and control device.It can replace a variety of meters, relays, transducersand other components. The power meter can beinstalled at multiple locations within a facility.The power meter is equipped with RS-485communications for integration into any powermonitoring and control system. However, SystemManager software (SMS) from POWERLOGIC,which is written specifically for power monitoring andcontrol, best supports the power meter’s advancedfeatures.The power meter is a true rms meter capable ofexceptionally accurate measurement of highlynonlinear loads. A sophisticated sampling techniqueenables accurate, true rms measurement through the63rd harmonic. You can view over 50 metered valuesplus minimum and maximum data from the display orremotely using software. Table 1–1 summarizes thereadings available from the power meter.Table 1–1:Summary of power meter InstrumentationReal-time ReadingsPower Analysis Current (per phase, residual, 3-Phase)Voltage (L–L, L–N, 3-Phase)Real Power (per phase, 3-Phase)Reactive Power (per phase, 3-Phase)Apparent Power (per phase, 3-Phase)Power Factor (per phase, 3-Phase)FrequencyTemperature (internal ambient)THD (current and voltage)Displacement Power Factor (per phase, 3-Phase)Fundamental Voltages (per phase)Fundamental Currents (per phase)Fundamental Real Power (per phase)Fundamental Reactive Power (per phase)Unbalance (current and voltage)Phase RotationHarmonic Magnitudes & Angles (per phase)Sequence ComponentsEnergy ReadingsDemand Readings Accumulated Energy, RealAccumulated Energy, ReactiveAccumulated Energy, ApparentBidirectional ReadingsReactive Energy by QuadrantIncremental EnergyConditional Energy 2003 Schneider Electric All Rights ReservedDemand Current (per phase present, 3-Phase avg.)Average Power Factor (3-Phase total)Demand Real Power (per phase present, peak)Demand Reactive Power (per phase present, peak)Demand Apparent Power (per phase present, peak)Coincident ReadingsPredicted Power Demands1
1IntroductionPower Meter HardwarePower Meter HardwareFigure 1–1: Parts of the Power Meter 800Bottom View21345Back View26 2003 Schneider Electric All Rights Reserved
1IntroductionPower Meter HardwareTable 1–2:No.Parts of the Power MeterPartDescription1Control power supply connectorConnection for control power to the power meter.2Voltage inputsVoltage metering connections.3I/O connectorKY pulse output/digital input connections4RS-485 port (COM1)The RS-485 port is used for communications with a monitoring andcontrol system. This port can be daisy-chained to multiple devices.5Option module connectorUsed to connect an option module to the power meter.6Current inputsCurrent metering connections.Power Meter Parts and AccessoriesTable 1–3:Power Meter Parts and AccessoriesDescriptionDocument NumberPower Meter with Integrated DisplayPM820PM820MGPower Meter without DisplayPM820UPM820UMGDisplayPM8DPM8DMGBox Contents Power MeterHardware kit containing:— Two retainers— Template— Install sheet— Lugs— DIN Slide— Plug set 2003 Schneider Electric All Rights Reserved3
1IntroductionFirmware Power Meter installation manualFeaturesSome of the power meter’s many features include: True rms metering to the 63rd harmonic High accuracy—0.075% current and voltage(typical conditions) Min/max readings of metered data Downloadable firmware Setpoint-controlled alarm and relay functions RS-485 communicationsAccepts standard CT and PT inputs600 volt direct connection on voltage inputsCertified ANSI C12.20 revenue accuracy and IEC60687 0.5S class revenue accuracyPower quality readings—THDReal-time harmonic magnitudes and angles to the31st harmonicEasy setup through the integrated display(password protected)Onboard alarm and data loggingWide operating temperature range: –25 to 70 Cfor the main unit, –10 to 50 C for the displayFirmwareSee “Identifying the Firmware Version, Model, andSerial Number” on page 78 for instructions on how todetermine the firmware version.Topics Not Covered in this BulletinSome of the power meter’s advanced features, suchas onboard data logs and alarm log files, can only beset up over the communications link using SMS. SMS4 2003 Schneider Electric All Rights Reserved
1IntroductionTopics Not Covered in this Bulletinversions 3.3 and higher support the PM800 devicetype.This power meter instruction bulletin describesthese advanced features, but does not tell how to setthem up. For instructions on using SMS, refer to theSMS online help and the SMS-3000 Setup Guide,which is available in English, French, and Spanish.For information about related instruction bulletins, seeTable 1–3 on page 3. 2003 Schneider Electric All Rights Reserved5
1IntroductionTopics Not Covered in this Bulletin6 2003 Schneider Electric All Rights Reserved
2Safety PrecautionsBefore You BeginSAFETY PRECAUTIONSBeforeYou BeginThis chapter contains important safety precautionsthat must be followed before attempting to install,service, or maintain electrical equipment. Carefullyread and follow the safety precautions outlined below.DANGERHAZARD OF ELECTRIC SHOCK, BURN, OR EXPLOSION Only qualified workers should install this equipment. Such workshould be performed only after reading this entire set ofinstructions. NEVER work alone. Before performing visual inspections, tests, or maintenance onthis equipment, disconnect all sources of electric power.Assume that all circuits are live until they have been completelyde-energized, tested, and tagged. Pay particular attention tothe design of the power system. Consider all sources of power,including the possibility of backfeeding. Turn off all power supplying this equipment before working onor inside. Always use a properly rated voltage sensing device to confirmthat all power is off. Beware of potential hazards, wear personal protectiveequipment, carefully inspect the work area for tools and objectsthat may have been left inside the equipment. Use caution while removing or installing panels so that they donot extend into the energized bus; avoid handling the panels,which could cause personal injury. The successful operation of this equipment depends uponproper handling, installation, and operation. Neglectingfundamental installation requirements may lead to personalinjury as well as damage to electrical equipment or otherproperty. Before performing Dielectric (Hi-Pot) or Megger testing on anyequipment in which the power meter is installed, disconnect allinput and output wires to the power meter. High voltage testingmay damage electronic components contained in the powermeter.Failure to follow this instruction will result in death orserious injury 2003 Schneider Electric All Rights Reserved7
2Safety PrecautionsBefore You Begin8 2003 Schneider Electric All Rights Reserved
3OperationOperating the DisplayOPERATIONOperatingthe DisplayThe power meter is equipped with a large, back-litLCD display. It can display up to five lines ofinformation plus a sixth row of menu options. Figure3–1 shows the different parts of the power meter.Figure 3–1: Power Meter DisplayA. Type of measurementABC DB. Screen TitleC. Alarm indicatorD. Maintenance iconE. Bar Chart (%)IF. UnitsAG. Display more menu itemsI.BCSelected menu indicatorJ. Button235245236MH. Menu 00{{{{{}}}}}}102.4NK. Return to previous menu! &S PER PHASE50A100%AI DMD.---:L. ValuesGM. PhaseKJIHHow the Buttons WorkThe buttons are used to select menu items, displaymore menu items in a menu list, and return toprevious menus. A menu item appears over one ofthe four buttons. Pressing a button selects the menuitem and displays the menu item’s screen. When youhave reached the highest menu level, a black triangleappears beneath the selected menu item. To return tothe previous menu level, press the button below 1;.To cycle through the menu items in a menu list, pressthe button below ###: (see Figure 3–1).NOTE: Each time you read “press” in this manual,press and release the appropriate button beneath the 2003 Schneider Electric All Rights Reserved9
3OperationMenu Overviewmenu item. For example, if you are asked to “PressPHASE,” you would press the button below thePHASE menu item.Changing ValuesWhen a value is selected, it flashes to indicate that itcan be modified. A value is changed by doing thefollowing: Press or – to change numbers or scroll throughavailable options. If you are entering more than one number, press - to move to the next number in the sequence. To save your changes and move to the next field,press OK.Menu OverviewThe figure below shows the menu items of the firsttwo levels of the power meter. Level 1 contains all ofthe menu items available on the first screen of thepower meter. Selecting a Level 1 menu item takesyou to the next screen level containing the Level 2menu items.NOTE: The ###: is used to scroll through all menuitems on a level.10 2003 Schneider Electric All Rights Reserved
3OperationMenu OverviewFigure 3–2: Abbreviated List of Power Meter Menu ItemsLEVEL 1AMPS (I)VOLTS (U-V)LEVEL 2PHASEI DMDL-LL-NUNBALPWR (PQS)SUMMENERG. (E)WHVARHPFT PFD PFV L-L (U)V L-N (V)PHASEDMDVAHHZTHDMIN/MXSUMMIVHARM.V L-L (U)ALARMACTIVHISTD IND OUTI/ORESETMETERSETUPDATEDIAGN.METERUNBALV L-N (V)ENERG (E)TIMEREGIPWRPFFTHD VTHD KADVANMAINTNote: IEEE (IEC) 2003 Schneider Electric All Rights Reserved11
3OperationSet Up the Power MeterSet Up the Power MeterTo begin power meter setup, do the following:1. Scroll through the Level 1 menu list until you seeSETUP.2. Press SETUP.3. Enter your password.NOTE: The default password is 0000.4. To save the changes, press1; until you areprompted to save the changes.Follow the directions in the following sections to setup the meter.Set Up Communications1. Press ###: until COMMS isvisible.2. Press COMMS.COMMS SETUP3. Select the communicationsprotocol: MBUS (MODBUS) orJBUS001384004. Press OK.5. Enter the ADDR (meter address).6. Press OK.7. Select the BAUD (baud rate):9600,19200, or 38400.MBUSADDR.baudnone1; - OK8. Press OK.9. Select how the parity: EVEN,ODD, NONE.10. Press 1; to return to the SETUPscreen.12 2003 Schneider Electric All Rights Reserved
3OperationSet Up the Power MeterSet Up the Date1. Press ###: until DATE is visible.2. Press DATE.DATE SETUP3. Enter the MONTH number.012320024. Press OK.5. Enter the DATE number.6. Press OK.7. Enter the YEAR number.8. Press OK.9. Select how the date is displayed:M/D/Y, D/M/Y, or Y/M/D.10. Press 1; to return to the SETUPscreen.01-23-021; - MONTHDATEYEARM/D/YOKSet Up the Time1. Press ###: until TIME is visible.2. Press TIME.TIME SETUP3. Enter the HOUR.2334584. Press OK.5. Enter the MIN (minutes).6. Press OK.7. Enter the SEC (seconds).8. Press OK.9. Select how the time is displayed:24H or AM/PM.10. Press 1; to return to the SETUPscreen. 2003 Schneider Electric All Rights ReservedHourMINSec24H1; - OK13
3OperationSet Up the Power MeterSet Up the Language1. Press ###: until LANG is visible.2. Press LANG (language).LANGUAGE3. Select the language: ENGL(English), SPAN (Spanish),FREN (French).ENGL.4. Press 1; to return to the SETUPscreen.1; - Set Up CTs1. Press ###: until METER isvisible.CT RATIO2. Press METER.3. Press CT.4. Enter the PRIM CT (primary CT)number.5. Press OK.6. Enter the SECON. CT(secondary CT) number.8005C TC TPRIMSECON.7. Press OK.8. Press 1; to return to the METERSETUP screen.1; - OK9. Press 1; to return to the SETUPscreen.14 2003 Schneider Electric All Rights Reserved
3OperationSet Up the Power MeterSet Up PTs1. Press ###: until METER isvisible.PT RATIO2. Press METER.3. Press PT.4. Enter the SCALE value: x1, x10,x100, NO PT (for direct connect).12015. Press OK.6. Enter the PRIM (primary) value.X1207. Press OK.8. Enter the SEC. (secondary)value.1; -NO PTPRIMSCALESEC. OK9. Press OK.10. Press 1; to return to the METERSETUP screen.11. Press 1; to return to the SETUPscreen.12. Press 1; to save the changes.Set Up the Meter System Type1. Press ###: until METERis visible.&METER Frequency2. Press METER.3. Press SYS.4. Select the SYS (system type).60605. Press OK.6. Select the FREQ (frequency).7. Press OK.8. Press 1; to return to the METERSETUP screen.9. Press 1; to return to the SETUPscreen. 2003 Schneider Electric All Rights Reserved1; - HzFREQ.OK15
3OperationSet Up the Power MeterSet Up Alarms1. Press ###: until ALARMis visible.&OVER V A-N2. Press ALARM.3. Press - or - to select thealarm you want to edit.4. Press EDIT.5. Select to enable or disable thealarm: ENABL (enable) or DISAB(disable).6. Press OK.7. Select the PR (priority): NONE,HIGH, MED, or LOW.ENABL.P R150P UP U1; - HIGH0VALUEDELAYOK8. Press OK.9. Enter the PU VALUE (pick-upvalue).10. Press OK.11. Enter the PU DELAY (pick-updelay).12. Press OK.13. Enter the DO VALUE (drop-outvalue).14. Press OK.15. Enter the DO DELAY (drop-outdelay).16. Press OK.17. Press 1; to return to the alarmsummary screen.18. Press 1; to return to the SETUPscreen.16 2003 Schneider Electric All Rights Reserved
3OperationSet Up the Power MeterSet Up I/Os1. Press ###: until I/O is visible.2. Press I/O.3. Press - or - to select theI/O.4. Press EDIT.M D005. Select the I/O mode based on theI/O type and the user selectedmode: NORM., LATCH, TIMED,PULSE, or END OF6. Depending on the modeselected, the power meter willprompt you to enter the pulseweight, timer, and control.&KY OUTPUTNORM.PULSETIMEREXT.1; - OK7. Press OK.8. Press 1; to return to the I/Oscreen.9. Press 1; to return to the SETUPscreen. 2003 Schneider Electric All Rights Reserved17
3OperationSet Up the Power MeterSet Up the Passwords1. Press ###: until PASSW(password) is visible.&PASSWORD SETUP2. Press PASSW.0000000000000003. Enter the SETUP password.4. Press OK.5. Enter the DIAG (diagnostics)password.6. Press OK.000007. Enter the ENERG (energy reset)password.1;8. Press OK. -SETUPDIAG.ENERG.MIN.MX OK9. Enter the MINMX(minimum/maximum reset)password.10. Press OK.11. Press 1; to return to the SETUPscreen.Set Up the Alarm Backlight1. Press ###: until BLINK is visible.2. Press BLINK.&3. Enter ON or OFF.4. Press 1; to return to the SETUPscreen.011;18 - ONOK 2003 Schneider Electric All Rights Reserved
3OperationAdvanced Power Meter Setup OptionsAdvanced Power Meter Setup OptionsTo setup the advanced power meter options, do thefollowing:1. Scroll through the Level 1 menu list until you seeSETUP.2. Press SETUP.3. Enter your password.NOTE: The default password is 0000.4. Press ###: until ADVAN (advanced setup) isvisible.5. Press ADVAN.Follow the directions in the following sections to setup the meter.Set Up the Phase Rotation1. Press ###: until ROT (phaserotation) is visible.6000000000003. Select the phase rotation: ABC orCBA.4. Press 1; to return to the SETUPscreen.000001; 2003 Schneider Electric All Rights Reserved&PHASE Rotation2. Press ROT. - ABCDIAG.ENERG.MIN.MXOK19
3OperationAdvanced Power Meter Setup OptionsSet Up the Incremental Energy Interval1. Press ###: until E-INC is visible.2. Press E-INC (inc
versions 3.3 and higher support the PM800 device type.This power meter instruction bulletin describes these advanced features, but does not tell how to set them up. For instructions on using SMS, refer to the SMS online help and the SMS-3000 Setup G
École Centrale Group CentraleSupélec leads the École Centrale Group. Together with École Centrale Lyon, École Centrale Lille, École Centrale Nantes and École Centrale Marseille, all located in France. CentraleSupélec develops international research and academic partnerships and exchanges, mostly in Europe, South-America and Asia.
1 Rappels de th eorie de la mesure Comme son nom l’indique, une mesure mesure des ensembles. Des exemples typiques de mesure sont le cardinal (d’un ensemble discret), la longueur (d’une courbe), l’aire d’une surface, la probabilit e (d’un ev enement). En g en eral, une mesure ne peut pas mesurer n’importe quel objet mais seulement certains objets adapt es a la nature de la mesure .
-Sanitair installateur (Martelaarslaan) -Stukadoor -Installateur centrale verwarming (Martelaarslaan) -Monteur centrale verwarming loodgieter (Martelaarslaan) -Monteur centrale verwarming technieker centrale -verwarming (Martelaarslaan) -Monteur centrale verwarming installateur individuele gasverwarming (Martelaarslaan)
Centrales de mesure 7KM PAC Centrale de mesure 7KM PAC3100 Bloc d'alimentation étendue CA/CC, bornes à vis 11/10 Appareil pour montage en tableau avec affi-cheur graphique, entrées et sorties TOR intégrées et interface RS 485 pour la trans-mission des valeurs de mesure et la confi-guration. A
4w00-mm postage meter rentals meter for connect green 1000/2000 & sendpro p1000/2000 76.00 59.28 22% 4w00-mh postage meter rentals meter for connect green 3000 & sendpro p3000 100.00 78.00 22% 1r0t postage meter rentals 1r0t postage meter 137.00 106.86 22% 1h00-mh postage meter rentals meter for sendpro c400 385.00 300.00 22%
BOX , LTCT METER, HT METER, GRID METER, PRODIGY METER & ABT METER. The bidder must qualify the technical requirements as specified in clause 2.0 stated below.The sealed envelopes shall be duly superscribed as v RATE CONTRACT FOR SUPPLY OF 3 PHASE METER WITH BOX & WITHOUT BOX , LTCT
CENTRALE MARSEILLE Plan stratégique 2014-2022 — 5 1. Objectif 2022 et axes stratégiques D’ici 2022, Centrale Marseille intégrera le Top 14 des écoles d’ingénieurs en France Pour cela, l’école Centrale de Marseille se fixe cinq objectifs chiffrés (indicateurs) qu’elle cherchera à
BC Hydro Meter Choices Program 10 The following test procedure was utilized: 1. Smart meter was installed in meter base with AC power connection 2. Smart meter was configured using local programming port to set the test meter's RFLAN and HAN radios to active state 3. Smart meter confirmed to be communicating with the collector through the RFLAN
