Back Saver Auger Mover Installation - Norwood Sales

2y ago
23 Views
2 Downloads
410.66 KB
5 Pages
Last View : 20d ago
Last Download : 2m ago
Upload by : Grady Mosby
Transcription

BACK‐SAVERAUGER MOVER INSTALLATIONBACK SAVERNorwood Sales Inc11202 38th Street SouthHorace, ND 58047PHONE: 701‐588‐4000FAX: 701‐588‐4004Toll Free: 800‐446‐0316Part No. 35‐5‐00002 – Back‐Saver Auger Mover InstallationRev. A, June 2011

Back‐SaverINSTALLATIONAssembly InstructionsYour Back‐Saver Auger Mover Kit should include the following:1. (1) Wheel and Tire Assembly2. (1) 3rd Wheel Hub3. (1) 3rd Wheel Mount Bracket4. (1) Auger Mover A‐Frame5. (2) Tube Clamp Top6. (1) Jack Mount Clamp Half7. (1) Mover Pivot Clamp Half8. (1) Mover Steering Handle9. (1) Jack Mount Pin10. (1) Mover Pivot Pin11. (1) Ball Coupler Hardware Kit12. (1) 1‐7/8” Hitch Ball13. (1) Bolt Bag1Auger Mover

Back‐SaverINSTALLATIONAuger MoverThe following instructions are for changing your Back‐Saver Swing Mover to an Auger Mover.Please refer to the Swing Mover Manual for base unit assembly along with Safety andMaintenance information.Step 1:Remove the Back‐Saver Base unit from the Swing Auger clamps. You can leave the Swing Augerclamps on the Swing Auger to make converting back quick and easy. At this time you will alsoremove the Jack Assembly from the Base Unit saving the 3/8” X 2‐1/2” bolt and nut for theAuger Mover installation.Step 2:Install the 1‐7/8” Ball Hitch in the top of the 3rd Wheel Bracket. Position the Base unit so thatyou are looking at it from the back side (gear motor side). Remove the bolts from the left sideof the gear motor and chain guard. Install the 3rd Wheel Bracket with the axle toward you,using the 3/8” X 1‐1/2” bolts in the bottom and the 3/8” X 1‐1/4” bolt in the upper (guard)location.Step 3:Bolt the Wheel and Tire Assembly to the 3rd Wheel Hub using the 1/2” X 1” bolts and WheelNuts. Slide the 3rd Wheel Hub and Wheel Assembly of the Axle on the 3rd Wheel Bracket andlock in place using the provided Linch Pin.Step 4:Mount the Steering Handle to the top of the Base Unit using the Pivot Pin and Linch Pins fromthe Original Swing Auger.Step 5:With the Auger sitting on the ground, loosely attach the lower Pivot Clamp about 4 feet up theauger. Install the ball coupler hardware to the Mover A‐Frame and attach to the Pivot Clampusing the Pivot Pin. Position the 3 Wheel Base Unit under the auger and connect to the A‐Frame using the Ball Coupler. Attach the Jack Mount Clamp to the auger just above the baseunit. The location will vary depending on bracket locations of the auger. Mount the Jackassembly between the Clamp and A‐Frame using the Jack Pin and the 3/8” X 2‐1/2” bolt thatwas removed earlier. Adjust the clamps so that the auger is on the ground when the jack is inthe retracted position, then tighten the bolts on the clamps.2

Back‐SaverINSTALLATIONAuger MoverStep 6:Mount the Receiver/Control Box (with the toggle switch up) to the Auger using the attachedmagnet. Ensure that the wire harness hangs down from the box to insure that water will notwick into the control box. Connect the 10 foot cord to the electric motor. Connect the 3 footcord to the light and mount the light facing the hopper.3

Back‐SaverOPERATIONAuger MoverOperationConnect the battery clips to your 12 volt battery source. The BLACK clip connects to thenegative terminal and the RED clip connects to the positive battery terminal.Once the power is connected the manual toggle switch on top of the control box will operatethe system at any time. To use the key‐fobs, press either arrow button to activate the motorand move the hopper. Pressing the light bulb button will turn on the work light for ten minuteIt is recommended that you remove the base unit and electronic controls before towing yourauger. The base unit can be quickly removed by releasing the ball coupler and retracting thejack.4

Back‐Saver INSTALLATION Auger Mover 1 Assembly Instructions Your Back‐Saver Auger Mover Kit should include the following: 1. (1) Wheel and Tire Assembly 2. (1) 3rd Wheel Hub 3. (1) 3rd Wheel Mount Bracket 4. (1) Auger Mover A‐Fr

Related Documents:

The toilet enters the energy saver mode from 9:00 to 15:00. Energy saver light is on Energy saver Setting energy saver time Press "ENERGY SAVER" button, LCD screen shows energy saver and figures. It shows three options of energy saver period as 3-6-9-off, which can be selected accordingly. For example, user can set from 9:00 to 15:00 as .

Hydraulic winch and hopper mover (std on 16" models) 8 BACKSAVER AUGER BACKSAVER AUGER 10", 13" AND 16" MODELS SELF-LEVELING The self-leveling hopper on the swing-away auger will remain level regardless of auger height. The unique design allows the intake hopper to be loaded on uneven

2 Electra-Saver II Models The 50 HP Electra-Saver II has the largest, most efficient airend in its class. The 150 HP Electra-Saver II is a gearless, direct drive compressor built to provide results. The 15–30 HP Electra-Saver II is shown tank-mounted.

Safety - 13" Backsaver Auger 15 SAFETY INSTRUCTIONS (CONT’D) Operation Safety † Ensure bystanders are clear of the area before operating. † The auger must be attached to the drawbar of the tractor at all times during operation. † Never stand under the auger while raising or low

sensors distributed about the piling rig as shown in Figure 2. 3.1.1 Concrete Pressure A pressure sensor at the top of the auger, attached to what is referred to as the swan-neck, is used to measure the pressure of concrete pumped through the auger during the concreting phase of piling. 3.1.2 Depth Two sensors on the rotary table or at the cat-

auger features to meet the demands of expanding farms. A hydraulic hopper mover and hydraulic winch system were made available on the Backsaver Auger to make it easier to prepare the auger for transport and for positioning the swing-away hopper. conventional grain augers are now available with a new

1 Lecture 16: Earth-Mover Distance COMS E6998-9 F15. Administrivia, Plan Administrivia: -NO CLASS next Tuesday 11/3 (holiday) Plan: -Earth-Mover Distance Scriber? 2. Earth-Mover Distance Definition: -Given two sets , of points in a metric space . -Can be plane, ℓ2,ℓ1 .

the American Board of Radiology (ABR) Core and Certifying examinations administered between January 1 – December 31, 2018. The guide has undergone a few minor changes compared to the 2018 version, which was significantly revised com- pared to earlier versions, reflecting changes in NIS content on the examinations. The primary change in this study guide is the addition of Core Concepts of .