MODEL DJ-3 DRAFT INDUCER TJERNLUND PRODUCTS, INC .
TJERNLUND PRODUCTS, INC.1601 Ninth Street White Bear Lake, MN 55110-6794PHONE (800) 255-4208 (651) 426-2993 FAX (651) 426-9547Visit our web site www.tjernlund.comMODEL DJ-3 DRAFT INDUCERSPECIFICATIONSMODELNO.GAS FIRINGWITHDRAFT HOODHEATERBTUINPUTFLUE GASS.P.DJ-3CFMOIL FIRINGWITHBAR. DRAFTCONTROLGAS FIRINGWITHBAR. DRAFTCONTROLHEATERBTUINPUTFLUE GASS.P.CFMHEATERBTUINPUTFLUE GASS.P.CFMoPIPESIZEIN.Static pressure inches H20 (70 F Air)Static pressures shown are “negative” and apply only on inlet sidePerformance Curves1. Inputs shown are believed to bemaximum capacities for inducers whenmounted on pipe sizes shown forordinary jobs where a moderate amountof mechanical induced draft is required.2. Consideration is given to typicallyhigher static pressure requirements forlarger installations, for the type of fuelburned and for the type of draft controlinstalled.3. Where pressure requirements areunknown or believed to be unusuallysevere, ask for complete performancecurves or consult factory.4. All ratings have been developed in ourtesting and research department andhave been approved by a nationallyknown independent testing laboratory.Certification is available upon request.5. Heating capacities shown are for 1000BTU per cubic foot natural gas and for139,000 BTU per gallon No. 2 fuel oil.Consult factory for capacities with otherfuels. Heating capacities are based ontypical combustion efficiencies andallow for approximately 5 percentambient air drawn into inducer tocool motor and drives.6. Draft Inducers should be installedin single wall vent pipe in orderto insure proper performance.Note: Tjernlund Products, Inc. reserves theright to make changes to specifications withoutnotification.MOTOR SPECIFICATIONSELECTRICAL DATAVoltsHertzRPMWattsAmpsTherm. Prot.11560155035.43Imp. Prot.P/N 8506000REV. C 11/05
TJERNLUND PRODUCTS, INC.1601 Ninth Street White Bear Lake, MN 55110-6794PHONE (800) 255-4208 (651) 426-2993 FAX (651) 426-9547Visit our web site www.tjernlund.comMODEL D-3 DRAFT INDUCERSPECIFICATIONSMODELNO.GAS FIRINGWITHDRAFT HOODHEATERBTUINPUTFLUE GASS.P. CFMD-3GAS FIRINGWITHBAR. DRAFTCONTROLHEATERBTUINPUTFLUE GASS.P. CFMOIL FIRINGWITHBAR. DRAFTCONTROLHEATERBTUINPUT2. Consideration is given to typicallyhigher static pressure requirements forlarger installations, for the type of fuelburned and for the type of draft controlinstalled.3. Where pressure requirements areunknown or believed to be unusuallysevere, ask for complete performancecurves or consult factory.oPIPESIZEIN.Static pressure inches H20 (70 F Air)Static pressures shown are “negative” and apply only on inlet sidePerformance curves1. Inputs shown are believed to bemaximum capacities for inducers whenmounted on pipe sizes shown forordinary jobs where a moderate amountof mechanical induced draft is required.FLUE GASS.P. CFM4. All ratings have been developed in ourtesting and research department andhave been approved by a nationallyknown independent testing laboratory.Certification is available upon request.5. Heating capacities shown are for 1000BTU per cubic foot natural gas and for139,000 BTU per gallon No. 2 fuel oil.Consult factory for capacities with otherfuels. Heating capacities are based ontypical combustion efficiencies andallow for approximately 5 percentambient air drawn into inducer tocool motor and drives.6. Draft Inducers should be installedin single wall vent pipe in orderto insure proper performance.Note: Tjernlund Products, Inc. reserves theright to make changes to specifications withoutnotification.MOTOR SPECIFICATIONSELECTRICAL DATAVoltsHertzRPMWattsAmpsTherm. Prot.11560155074.96Yes
TJERNLUND PRODUCTS, INC.1601 Ninth Street White Bear Lake, MN 55110-6794PHONE (800) 255-4208 (651) 426-2993 FAX (651) 426-9547Visit our web site www.tjernlund.comMODEL I DRAFT INDUCERSPECIFICATIONSMODELNO.GAS FIRINGWITHDRAFT HOODHEATERBTUINPUTFLUE GASS.P. CFMIGAS FIRINGWITHBAR. DRAFTCONTROLOIL FIRINGWITHBAR. DRAFTCONTROL2. Consideration is given to typicallyhigher static pressure requirements forlarger installations, for the type of fuelburned and for the type of draft controlinstalled.3. Where pressure requirements areunknown or believed to be unusuallysevere, ask for complete performancecurves or consult factory.oPIPESIZEIN.Static pressure inches H20 (70 F Air)Static pressures shown are “negative” and apply only on inlet sidePerformance curves1. Inputs shown are believed to bemaximum capacities for inducers whenmounted on pipe sizes shown forordinary jobs where a moderate amountof mechanical induced draft is required.HEATERBTUINPUTFLUE GASS.P. CFMHEATERBTUINPUTFLUE GASS.P. CFM4. All ratings have been developed in ourtesting and research department andhave been approved by a nationallyknown independent testing laboratory.Certification is available upon request.5. Heating capacities shown are for 1000BTU per cubic foot natural gas and for139,000 BTU per gallon No. 2 fuel oil.Consult factory for capacities with otherfuels. Heating capacities are based ontypical combustion efficiencies andallow for approximately 5 percentambient air drawn into inducer tocool motor and drives.6. Draft Inducers should be installedin single wall vent pipe in orderto insure proper performance.Note: Tjernlund Products, Inc. reserves theright to make changes to specifications withoutnotification.MOTOR SPECIFICATIONSELECTRICAL DATAVoltsHertzRPMWattsAmpsTherm. Prot.1156017251/4 HP5.4Yes
TJERNLUND PRODUCTS, INC.1601 Ninth Street White Bear Lake, MN 55110-6794PHONE (800) 255-4208 (651) 426-2993 FAX (651) 426-9547Visit our web site www.tjernlund.comMODEL IL DRAFT INDUCERSPECIFICATIONSMODELNO.GAS FIRINGWITHDRAFT HOODHEATERBTUINPUTFLUE GASS.P. CFMILGAS FIRINGWITHBAR. DRAFTCONTROLHEATERBTUINPUTFLUE GASS.P. CFMOIL FIRINGWITHBAR. DRAFTCONTROLHEATERBTUINPUT2. Consideration is given to typicallyhigher static pressure requirements forlarger installations, for the type of fuelburned and for the type of draft controlinstalled.3. Where pressure requirements areunknown or believed to be unusuallysevere, ask for complete performancecurves or consult factory.oPIPESIZEIN.Static pressure inches H20 (70 F Air)Static pressures shown are “negative” and apply only on inlet sidePerformance curves1. Inputs shown are believed to bemaximum capacities for inducers whenmounted on pipe sizes shown forordinary jobs where a moderate amountof mechanical induced draft is required.FLUE GASS.P. CFM4. All ratings have been developed in ourtesting and research department andhave been approved by a nationallyknown independent testing laboratory.Certification is available upon request.5. Heating capacities shown are for 1000BTU per cubic foot natural gas and for139,000 BTU per gallon No. 2 fuel oil.Consult factory for capacities with otherfuels. Heating capacities are based ontypical combustion efficiencies andallow for approximately 5 percentambient air drawn into inducer tocool motor and drives.6. Draft Inducers should be installedin single wall vent pipe in orderto insure proper performance.Note: Tjernlund Products, Inc. reserves theright to make changes to specifications withoutnotification.MOTOR SPECIFICATIONSELECTRICAL DATAVoltsHertzRPMWattsAmpsTherm. Prot.1156017251/4 HP5.4Yes
TJERNLUND PRODUCTS, INC.1601 Ninth Street White Bear Lake, MN 55110-6794PHONE (800) 255-4208 (651) 426-2993 FAX (651) 426-9547Visit our web site www.tjernlund.comMODEL XL DRAFT INDUCERSPECIFICATIONSMODELNO.GAS FIRINGWITHDRAFT HOODHEATERBTUINPUTFLUE GASS.P. CFMXLGAS FIRINGWITHBAR. DRAFTCONTROLOIL FIRINGWITHBAR. DRAFTCONTROL2. Consideration is given to typicallyhigher static pressure requirements forlarger installations, for the type of fuelburned and for the type of draft controlinstalled.3. Where pressure requirements areunknown or believed to be unusuallysevere, ask for complete performancecurves or consult factory.oPIPESIZEIN.Static pressure inches H20 (70 F Air)Static pressures shown are “negative” and apply only on inlet sidePerformance curves1. Inputs shown are believed to bemaximum capacities for inducers whenmounted on pipe sizes shown forordinary jobs where a moderate amountof mechanical induced draft is required.HEATERBTUINPUTFLUE GASS.P. CFMHEATERBTUINPUTFLUE GASS.P. CFM4. All ratings have been developed in ourtesting and research department andhave been approved by a nationallyknown independent testing laboratory.Certification is available upon request.5. Heating capacities shown are for 1000BTU per cubic foot natural gas and for139,000 BTU per gallon No. 2 fuel oil.Consult factory for capacities with otherfuels. Heating capacities are based ontypical combustion efficiencies andallow for approximately 5 percentambient air drawn into inducer tocool motor and drives.6. Draft Inducers should be installedin single wall vent pipe in orderto insure proper performance.Note: Tjernlund Products, Inc. reserves theright to make changes to specifications withoutnotification.MOTOR SPECIFICATIONSELECTRICAL DATAVoltsHertzRPMWattsAmps115, 208-2306017253/4 HP11 @ 1155.4 @ 2085.3 @ 230Therm. Prot. Yes
TJERNLUND PRODUCTS, INC.1601 Ninth Street White Bear Lake, MN 55110-6794PHONE (800) 255-4208 (651) 426-2993 FAX (651) 426-9547Visit our web site www.tjernlund.comMODEL HD DRAFT INDUCERSPECIFICATIONSPIPESIZEIN.GAS FIRINGWITHDRAFT HOODGAS FIRINGWITHBAR. DRAFTCONTROLOIL FIRINGWITHBAR. DRAFTCONTROLoMODELHEATERBTUINPUTFLUE GASS.P. CFMHDStatic pressure inches H20 (70 F Air)Static pressures shown are “negative” and apply only on inlet sidePerformance curvesHEATERBTUINPUTFLUE GASS.P. CFMHEATERBTUINPUTFLUE GASS.P. CFM1. Inputs shown are believed to bemaximum capacities for inducers whenmounted on pipe sizes shown forordinary jobs where a moderate amountof mechanical induced draft is required.2. Consideration is given to typicallyhigher static pressure requirements forlarger installations, for the type of fuelburned and for the type of draft controlinstalled.3. Where pressure requirements areunknown or believed to be unusuallysevere, ask for complete performancecurves or consult factory.4. All ratings have been developed in ourtesting and research department andhave been approved by a nationallyknown independent testing laboratory.Certification is available upon request.5. Heating capacities shown are for 1000BTU per cubic foot natural gas and for139,000 BTU per gallon No. 2 fuel oil.Consult factory for capacities with otherfuels. Heating capacities are based ontypical combustion efficiencies andallow for approximately 5 percentambient air drawn into inducer tocool motor and drives.6. Draft Inducers should be installedin single wall vent pipe in orderto insure proper performance.Note: Tjernlund Products, Inc. reserves theright to make changes to specifications withoutnotification.MOTOR SPECIFICATIONSELECTRICAL DATAVoltsHertzRPMWattsAmps208-230, 4606017252 HP6.3 @ 2086.4 @ 2303.2 @ 460Therm. Prot. No
model d-3 draft inducer specifications performance curves d-3 model no. pipe gas firing with with control bar. draft draft hood with in. size control bar. draft gas firing oil firing input flue gas flue gas heater btu input btu input flue gas btu s.p. cfm s.p. cfm s.p. cfm tjernlund products, inc. 1601 ninth street white bear lake, mn 55110 .File Size: 221KB
NOTE: The models DJ-3 & D-3 do not require bands, use mounting screws provided. 3. Select a position between draft hood, draft diverter or barometric damper and chimney, locating the inducer as near the chimney as possible. The motor shaft must be le
VH-180 440-767-000 Inducer assembly complete VH-150 440-766-000 Inducer assembly complete VH-120 440-765-000 DESCRIPTION PART # DESCRIPTION PART # VICTO
Resume the dose that was used prior to initiating the strong CYP3A4 inducer 2 to 3 days after discontinuation of the strong inducer. Do not exceed a daily dose of 80 mg [see . Drug Interactions (7.1), Clinical Pharmacology (12.3)]. 2.7 Dosage Mo
1 - Installation Instructions ELECTRICAL SPECIFICATIONS Specification Value Unit Input Voltage 18-30 VAC Input Current Max 800 mA Line Frequency 50/60 Hz Inducer Relay at 120V 3.0/6.0 FLA/LRA Inducer Relay at 240V 1.5/3.0 FLA/LRA Main Gas Valve Relay Max (Direct Spark System Only) 4.0 Amp Main Gas Valve Relay Max (Inter-mittent Pilot .
Final Date for TC First Draft Meeting 6/14/2018 3/15/2018 Posting of First Draft and TC Ballot 8/02/2018 4/26/2018 Final date for Receipt of TC First Draft ballot 8/23/2018 5/17/2018 Final date for Receipt of TC First Draft ballot - recirc 8/30/2018 5/24/2018 Posting of First Draft for CC Meeting 5/31/2018 Final date for CC First Draft Meeting .
DRAFT DOCUMENT FOR PUBLIC COMMENTS DRAFT DOCUMENT DRAFT DOCUMENT FOR PUBLIC COMMENTS DRAFT DOCUMENT . means a quantity standard for determining throughput of game carcasses in a . The Scheme is applicable throughout the Republic of South
to conditions that resulted from austerity following the financial crisis of 2008. . Broadly speaking three ‘waves’ of feminism have occurred in the EU . organisations that have appeared in the five-year period up to 2015 and that e
An introduction to the digital agenda and plans for implementation Authors Matthew Honeyman Phoebe Dunn Helen McKenna September 2016. A digital NHS? Key messages 1 Key messages Digital technology has the potential to transform the way patients engage with services, improve the efficiency and co-ordination of care, and support people to manage their health and wellbeing. Previous .
