1. Refer To Sycamore Creek 8'x12' Shed Roof Shed Plans For .

LP SHED ASSEMBLY INSTRUCTIONS SYCAMORE CREEK 8'x12' SHED ROOF SHED1. Refer to Sycamore Creek 8'x12' Shed Roof Shed plans for actual lumber dimensions and details.2. Refer to lpshed.com for additional application and installation details to help build your shed.Shed images are for illustrative purposes only.Louisiana-Pacific Corporation (LP) has provided the shed designs described as a general guide to those who are interested in building sheds or in having a shed built. We do not claim that the designs or that the materials we describe are correct or the only options you have. LP has prepared each design in an attempt to satisfygenerally accepted building rules and regulations. However, the designs were created without any knowledge of local conditions or geographic variables. Specific soil conditions, snow loads, wind loads, frost depth and materials will vary and may require modifications. LP cannot assure that the structures made using ourdesigns meet your local conditions or local building code requirements. Local laws may require a permit. You are responsible for verifying that the design you choose conforms to your local building code. We strongly recommend that you: (a) contact a licensed contractor for detailed plans and construction advice; (b) contact alocal building official to verify that the design meets your code requirements; and (c) check your neighborhood covenants before starting a shed project so that you can determine the appropriate size, location and approvals needed for a shed. LP is not responsible for changes made to a design. LP does not perform constructionsupervision and is not responsible for verifying that construction conforms to a design. LP is not responsible for how the construction work is performed including methods, sequences, techniques or procedures of construction. LP is not responsible for site safety.LP makes no representations or warranties of any kind, express or implied, relating to the completeness, accuracy, reliability, suitability or availability of the designs or materials shown here. Without limiting the prior sentence, we specifically disclaim the implied warranties of merchantability and fitness for a particular purposeto the extent allowed under applicable state laws. Any reliance you place on the information in this plan is at your own risk.You agree that LP will not be liable for any loss, damage or injury arising from the use of the designs and the materials described in this plan, whether such loss, damage or injury is claimed to be directly, indirectly, consequentially or incidentally caused by LP. You agree and acknowledge that the sole and exclusive remedy of anysuch claim, including attorneys’ fees and costs, shall not exceed 100.00.

BEFORE YOU STARTMATERIALS LISTHARDWARE IPTION68x8x16 cmu blocks8Angle brackets for 6x6 platform beams302x4x8' wall studs150Screws for platform flooring44x4x8' corner posts400Nails for wood stud wall framing162x6x8' roof rafters400Nails for wall panel siding and trim12x10x8' ridge beam200Nails for roof panels122x4x8' studs for horizontal/vertical blocking122x4x10' studs for top & bottom plates122x6x8' floor joists22x6x12' rim joists for floor joist members26x6x12' platform beams82x4x4' studs for vertical gable end wall studs50 lfMetal flashing32'–0"x3'–0" windows (by Owner)1 pair2'–0"x6'–8" doors (by Owner)96 sfLP ProStruct floor panels*230 sfLP SmartSide siding panels210 sfLP ProStruct Roof Sheathing with SilverTech **230 lf1x4 LP SmartSide trim boards210 sfRoofing material (by Owner)*If this product is unavailable, you can substitute LP TopNotch Sub-Flooring.**If this product is unavailable, you can substitute LP TechShield Radiant Barrier Sheathing or LP OSB sheathing.Door and window hardware by Owner2

FOUNDATION1. M ost buildings of less than 120 square feet do not require a building permitfrom the local building department, but be sure to check with your localauthorities before starting construction.2x6 RAFTER/FASCIA W/RAFTERTAILOWNER-SUPPLIED ROOFINGMATERIALS3'-5"2. C ontact your local building department to locate existing undergroundutility lines for you. You don’t want to disturb or hit any lines while preparingyour foundation.1LP PROSTRUCT ROOFSHEATHING WITH SILVERTECH2WINDOW ASSEMBLY BY OWNER1241'-0"FLASHING ABOVE ALL HORIZONTALLP SMARTSIDE TRIM BOARDSLP SMARTSIDE PANEL SIDING3'-0"Scale: 1 1/2" 1'-0"2x4 TOP PLATELP SMARTSIDE PANEL SIDING4. T he shed floor also needs to sit at least 6" above the surrounding ground,for proper rainwater drainage and to prevent the shed from absorbing anystanding rainwater.Detail3LP SMARTSIDE TRIM BOARDSFLASHING ABOVE ALL HORIZONTALLP SMARTSIDE TRIM BOARDS1'-6 1/4"3. R efer to the LP website lpshed.com/advice/buildshedfoundation for more1x4 LP SMARTSIDE TRIM BOARDdetailed instruction on how to prep and ready your site for the shed foundation.(2)2x4 SILLImportant:Theshed needs to sit on a stable/levelsurface, enabling the doorsLP SMARTSIDE PANELSIDINGto work properly.RIPPED 2x6 BLOCKING BETWEENRAFTERS32x4 STUDS @ 16" O.C.2x4 WINDOW FRAMINGLP PROSTRUCT FLOOR PANEL2x4 BOTTOM PLATE5 1/2"FLASHING3'-0"LP SMARTSIDE PANEL SIDINGLP SMARTSIDE PANEL SIDING2x4 FRAMING STUDS @ 16" O.C.2x6 FLOOR JOISTS41x4 LP SMARTSIDE TRIM BOARD5 1/2"Z-FLASHINGFINISHED FLOORLP PROSTRUCT FLOOR PANEL2x6 TREATED FLOOR JOISTS @ 16" O.C.FLASHING ABOVE ALL HORIZONTALLP SMARTSIDE TRIM BOARDS6x6 TREATED PLATFORM BEAMTREATED 6x6 PLATFORMFINISHED GRADEFINISHED GRADEFOUNDATION BY OWNERCross-Section8x8x16 CMU FOOTINGDetailScale: 1 1/2" 1'-0"NOTE: Refer to "LPSHED.com/advice/buildshedfoundation" for all site prep information.For exclusive use with all LP SMARTSIDE , LP PROSTRUCT , and LP SILVERTECH building materials.2 1/2"3 1/2"1"2"511 1/2"1/8"35 1/2"1"4Scale: 1/2" 1'-0"5"Roof Rafter CutsScale: 3/4" 1'-0"Please refer to "lpshed.com" for additional application andinstallation details to help build your shed.Sycamore Creek8'x12' Shed RoofA63

SHED PLATFORM/FLOORING8'-0"3'-0"1. L ay out the perimeter of the shed, either with a stringline or with stakesmarking the corners.2'-0" EST.3'-0"3" 5 1/2" 3/4"5 1/2"3. I nstall (6) 8"x8"x16" concrete masonry units (cmu’s) at the corners andmid-span of the 12' length of 6x6 platform. Be sure the cmu’s are leveland straight in line with the overall dimensions of this 8'x12' shed.4x4 CORNER POSTS1'-4 3/8"1'-1 1/8"3"2'-0"3"3 1/2"3 1/2"1'-1"8x8x16 CMU FOUNDATIONBLOCK1'-4 1/8" 3"2'-0"2'-0" EST.2'-0"x3'-0" WINDOWBY OWNER12'-0"6. I nstall sheets of LP ProStruct floor panels following the LP ProStruct Flooringinstallation instructions found at lpcorp.com/resources/product-literature.DetailBe sure to staggerthe seams between floor panels so 4 corners of 4 panels do3not meet. Scale: 1 1/2" 1'-0"1'-4 3/8"(2)2x4 WINDOW BLOCKING3"1x4 LP SMARTSIDE TRIM BOARD5. C ut and install the 2x6 floor joists at 16" on center, attach to the 6x6’s with lag(2)2x4 SILLboltsandPANELwashersLP SMARTSIDESIDING or with joist hangers. Adjust the diagonal measurementsuntil they are equal. The platform framing will then be square.1'-1 1/8"2'-4"5'-0"4. L ay the 6x6’s across the 3 cmu’s on each side of the shed. Test and adjustas needed for levelness and squareness. To achieve squareness, measurediagonally from corner to opposite corner of the 6x6’s. You can adjust thisWINDOW ASSEMBLY BY OWNERas you build the platform.LP SMARTSIDE TRIM BOARDS1'-0 1/2"2. This shed will rest on an assembly of 6x6 and 2x6 wood framing members.3 1/2"ENDWALL 2x4 STUD2'-0"x3'-0" WINDOWLP SMARTSIDE PANEL SIDING1'-1 7/8"2x4 STUDS @ 16" O.C.2'-0"x3'-0" WINDOW2x4 BOTTOM PLATE1'-1 7/8"5'-0"LP PROSTRUCT FLOOR PANEL8x8x16 CMU FOUNDATIONBLOCKLP SMARTSIDE PANEL SIDING1'-0 1/2"5 1/2"FLASHING2x6 FLOOR JOISTS2x4 STUDS @ 16" O.C. (MIN.)(2)2x4 DOOR BLOCKING1x4 LP SMARTSIDE TRIM BOARD3 1/2"5 1/2"Z-FLASHING6x6 TREATED PLATFORM BEAMFINISHED GRADE(2)2'-0"x6'-8" DOORS & FRAMEBY OWNER8x8x16 CMU FOOTING41'-11 1/4"DetailFloor PlanScale: 1 1/2" 1'-0"Scale: 1/2" 1'-0"4'-1 1/2" ESTIMATED1'-11 1/4"8'-0"2 1/2"2"1/3 1/2"35 1/2"1"NOTE: Refer to "LPSHED.com/advice/buildshedfoundation" for all site prep information.For exclusive use with all LP SMARTSIDE , LP PROSTRUCT , and LP SILVERTECH building materials.Please refer to "lpshed.com" for additional application andinstallation details to help build your shed.Sycamore Creek8'x12' Shed Roof4A1

WALLS1. L ay out the (2) 4x4 corner posts and 2x4 studs (at 16" on center) on the shedfloor. Use the shed floor as a guide to constructing your walls, since the floor islevel and square.3. S ecure the ends of the posts and studs with 2x4 top and bottom stud plates ateach end. Drive screws through these top and bottom plates into the posts andstuds to hold them in place. We will be adding a second top plate member afterall walls are erected.4. I nstall the horizontal cross bracing/blocking between the studs with 2x4’s cutto length.2x6 RAFTER/FASCIA W/RAFTERTAIL3'-5"OWNER-SUPPLIED ROOFINGMATERIALSLP PROSTRUCT ROOFSHEATHING WITH SILVERTECH2RIPPED 2x6 BLOCKING BETWEENRAFTERS1241'-0"FLASHING ABOVE ALL HORIZONTALLP SMARTSIDE TRIM BOARDS3'-0"LP SMARTSIDE PANEL SIDING32x4 WINDOW FRAMINGLP SMARTSIDE PANEL SIDING3'-0"7. C onstruct the remaining 3 walls in a similar fashion, making sure to frameproperly for all appropriate openings in the walls. Allow the shorter 8' endwalls to rest within the corner posts. Temporarily hold these walls in placewith diagonal bracing.2x4 FRAMING STUDS @ 16" O.C.4FINISHED FLOORLP PROSTRUCT FLOOR PANEL2x6 TREATED FLOOR JOISTS @ 16" O.C.FLASHING ABOVE ALL HORIZONTALLP SMARTSIDE TRIM BOARDS8. B efore continuing, re-measure all corners and walls, making sure all are leveland plumb as needed.9. A ttach 2x4 top plates to the tops of the wall assembly. Overlap the jointswhere the walls come together with the top plates. Continue installation ofthese top plates all around the perimeter of the walls.2x4 TOP PLATELP SMARTSIDE PANEL SIDING5. Continuously measure the wall to be sure it is square.6. A fter the studs and corner posts are secured to the top and bottom plates,raise the wall into place on the shed floor. Attach 2x4 diagonal bracing to thetop of the wall at each end. Use a level to determine that the corner posts areperfectly plumb and vertically square. Once square, screw the diagonal braceto the outside face of the platform to hold the wall in place.LP SMARTSIDE TRIM BOARDSFLASHING ABOVE ALL HORIZONTALLP SMARTSIDE TRIM BOARDS1'-6 1/4"2. W hen framing window and door openings, use 2 2x4 studs on each side ofthe openings.1TREATED 6x6 PLATFORMFINISHED GRADEFOUNDATION BY OWNERCross-SectionScale: 1/2" 1'-0"NOTE: Refer to "LPSHED.com/advice/buildshedfoundation" for all site prep information.For exclusive use with all LP SMARTSIDE , LP PROSTRUCT , and LP SILVERTECH building materials.Please refer to "lpshed.com" for additional application andinstallation details to help build your shed.Sycamore Creek8'x12' Shed RoofA65