Isokern Brochure - Almondsbury Forge - Almondsbury Forge
PUMICESYSTEM CHIMNEYS & LINERS.naturally betterDOC/CP3/64 SAP Issue 6 940002642 February 2017Part of the BRAAS MONIER BUILDING GROUP
Pumice - naturally betterPumice is a natural insulator. This is the unique property that separates pumice from all otherchimney materials.The insulating properties of Pumice allow the flue gases in the chimney to quickly reach their optimumtemperature enabling the heating appliance to reach its optimum performance shortly after lighting.It also keeps the chimney warmer longer as the heat output of the appliance decreases- once again aiding performance and reducing the likelihood of condensation and soot build-up.The natural properties of pumiceResistant to temperature changePumice has very little expansion and contraction withtemperature change. This reduces the possibility of crackingand structural damage that can occur with other products.High Insulation PropertiesPumice is a natural insulator, able to maintain the temperatureof flue gases when other products have allowed thetemperature to fall below the dew point.LightweightPumice is strong yet lightweight allowing one person to lift andbuild the chimney units.Pumice is a naturalmaterial sourced from theHekla Volcano in Iceland.Pumice is an excellent insulator,keeping flue gases warm while nottransmitting heat to the outside.Product DescriptionSchiedel Isokern products can be used for new chimneys and for the refurbishment of existingchimneys. The Isokern chimney systems provide a lightweight, easily installed and versatile chimneywhich can be used internally or externally.The systems are suitable for use with burning appliances innew and refurbished projects.They are ideal for Masonry,Timber Frame and Steel Frame construction.Isokern chimneys have been installed in Europe for over 60 years.2DM (DOUBLE MODULE)FLUE LINERSSchiedel Isokern DM block system is a highquality System Chimney. The double wallsystem maintains flue gas temperatureswhile preventing heat transference to theouter casing. The separation of the innerand outer components also allows forthermal movement, reducing the risk ofcracking and subsequent leaking or staining.It is simple and quick to build. The DM isavailable in 3 outer casing sizes - DM36,DM44 & DM54.The Schiedel Isokern flue liner rangeconsists of over 15 different sizes. Theycan be used for newbuild, extensions andrelining existing chimneys.FIRECHESTSISOKOAT FLUE SEALING SYSTEMThe Schiedel Isokern range of firechestsare supplied as flat packs.They can be easilyand quickly constructed to produce a neatand pre-formed fire opening ready forfinishing. The Magnum Firechest providesthe opportunity to create fire openings upto 1.2m wide.The Schiedel Isokoat system is an efficientand cost effective method of re-sealinga defective chimney shaft. The Isokoatmaterial is applied to the chimney underpressure and forced into the crackssealing them, re-pointing the joints andstrengthening the walls. For further detailssee the separate Isokoat leaflet.
DM Double Module Chimney SystemWhen the ease of construction and maximum insulation matter then the Double Module Systemcomes into its own. The system is designed to be quick and easy to install.The lightweight blocks are easy to handle. The outer and inner blocks are laid at the same time butwith staggered joints for safety and stability. The double layer of pumice blocks separated by an airgap maximises the chimney insulation.The Pumice Systems are suitable for wood burning, solid fuel, oil and gas (not condensing appliances).There are 3 systems covering a range of different internal diametersto meet the requirements of different appliances and uses:DM 36150mm internal diameter for smaller outputinserts, stoves and solid fuel/oil cookersDM 44180mm and 200mm internal diameters forinserts, stoves and open firesDM 54300mm and 345mm internal diameters forMagnum firechests and larger appliances,inserts and open firesUnique features of theIsokern DM Chimney SystemZero distance to combustibles on straight renderedchimneysQuick and easy to assembleLightweight materials, easy to handleHighly insulating pumice for better draw andminimum heat lossStaggered joints for maximum safety and stabilityAir gaps between outer casing and flue preventssurface stainingGood resistance to temperature variations givesthe maximum performance for your applianceApprovalsIsokern Pumice Double Module DM is CE Certified to EN1858 TÜV Cert no. 0036 CPR 90219 001Isokern Pumice Chimney Liner is CE certified to EN1857 TÜV Cert no. 0036 CPR 90219 002Isokern Magnum Firechest has been tested at the Fraunhofer Institut, Stuttgart, Cert no. P8-094/2006CE DesignationDouble Module DM System Chimney*T450 N1 D 3 G(00)Pumice Chimney LinerT450 N2 D 3 G* Zero distance to combustibles on straight chimney systems with ventilated terminal.38mm distance to combustibles on offset systems. and non ventilated systems.3
DM 36 for smaller output inserts, stoves and cookersAvailable in Ø150mm internal diameter only.RaincapTop RingCapping for renderedchimney stackCasings renderedabove roofLead flashingAll joints sealedwith lip glueDM casings can befinished with plasterChimney potSupport block andadaptor for connectionto flue pipeGlass frontedinset fireSand/cementflaunchingCapping for brickchimney stackWeep holesabove trayLead tray andflashingRaincapTop RingCapping for renderedchimney stackCasing renderedabove roofLead flashingCorbel forbrick stackFlue blocks installedwith socket uppermostStaggered jointsbetween casingand flue block2 x casingties at maximumintervals of1.5 metresINSET FIREOuter casings drylined or plasteredFlue pipe fitted intoaccess casing at 45 Support blockand adaptorfor connectionto stove pipeFREE STANDING STOVE IN A RECESS.System includes a Stainless Steel adaptor for ease ofconnection between the stove and the DM Chimney.Downloadable drawings available from our web sitewww.schiedel.co.uk4FREE STANDING STOVEWITH EXTERNAL CHIMNEY ANDPREFORMED FLUE ENTRY KIT
DM 36 for smaller output inserts, stoves and cookersDescriptionDM 36SAP CodeWeight (kg)All dimensions are external unless otherwise stated130714360mm square casing 250mm high15130712360mm square access casing 250mm high(150mm i/d access hole)13130713360mm square casing & soot door 250mm high18130709DM36 45º flue entry kit (four parts) 500mm high42126363150mm i/d 255 x 255 starter flue block 125mm high4126369150mm i/d 255x255 flue block 250mm high8126368150mm i/d 255x255 access flue block 500mm high(177mm i/d access hole)16130715570mm square corbel for brickwork 75mm high32130710130711490mm square capping - render690mm square capping - brickwork1331126378150mm i/d 360 x 435 offset block (86mm, 30 offset) 150mm high(allow 38mm distance to combustibles on offset chimneys)25130716150mm i/d 360 square support block 100mm high15126373150mm i/d (205mm o/d) stainless steel adaptor126357125-150mm i/d (205mm o/d) stainless steel decreaser adaptor130732Raincap (with fixing rods for top ring)135070Top Ring (for ventilation)5
DM 44 for inserts, stoves and small open firesAvailable in internal diameters Ø180mm and Ø200mm.Both inner liners fit into the same external block size.RaincapTop RingChimney potCapping for brickchimney stackSand/cementflaunchingCapping for brickchimney stackLead tray andflashingLip glue to seal joints40115 corbel tocomplete brick stackWeep holesabove trayCorbel for brickchimney stackInner flue blocks withsocket uppermostStaggered joints betweencasing and flue blockInner flue blocks withsocket uppermostStaggered jointsbetween casingand flue blockDM44 casings builtinto inner leaf ofcavity wallDM44 gatherOuter casings drylined or plastered38mm clearancefrom structural timberSupport block andadaptor for connectionto flue pipeStandard firechest(finished fireplaceopening size 590 x 550mm)Suitable foundationOPEN FIRE USINGSTANDARD FIRECHESTGlass fronted inset fireINSET FIREDownloadable drawings available from our web sitewww.schiedel.co.uk6
DM 44 for inserts, stoves and small open firesDescriptionDM 44SAP CodeWeight (kg)All dimensions are external unless otherwise stated130727440mm square casing 300mm high30130725440mm square access casing 300mm high(220mm i/d access hole)29130726440mm square casing & soot door 300mm high36130719130722440mm 180mm i/d 45 flue pipe entry kit (4 parts) 600mm high440mm 200mm i/d 45 flue pipe entry kit (4 parts) 600mm high8684130720127684180mm i/d 310 x 310 starter flue block 150mm high200mm i/d 310 x 310 starter flue block 150mm high87127068127683180mm i/d 310 x 310 flue block 300mm high200mm i/d 310 x 310 flue block 300mm high1514130717127682180mm i/d flue 310 x 310 access block 600mm high200mm i/d flue 310 x 310 access block 600mm high2826130728130235650mm square corbel for brickwork 75mm high650 x 560mm offset corbel for brickwork 75mm high4034130818740mm T corbel for external brickwork 75mm high47130723130724570mm square capping for render820mm square capping for brickwork1844131810130718127686127687180mm i/d 440 x 500 offset block (56mm, 30 offset) 100mm high180mm i/d 440 x 500 offset block (86mm, 30 offset) 150mm high200mm i/d 440 x 500 offset block (56mm, 30 offset) 100mm high200mm i/d 440 x 500 offset block (86mm, 30 offset) 150mm high(Allow 38mm distance to combustibles on offset chimneys)22222030130721130730180mm i/d 440mm square support block 100mm high200mm i/d 440mm square support block 100mm high2220127691200mm i/d (255mm o/d) stainless steel adaptor127671127672150-200mm i/d (255mm o/d) stainless steel decreaser adaptor175-200mm i/d (255mm o/d) stainless steel decreaser adaptor130732Raincap (with fixing rods for top ring)130675Top Ring (for ventilation)7
DM 54 for larger open fires and appliancesAvailable in internal diameters Ø300mm and Ø345mm.Both inner liners fit into the same external block size.Chimney potCapping for renderedchimney stackCasings renderedabove roofLead flashingDM casings can befinished with plasterJoints sealed with lip glueStaggered jointsbetween casingand flue blockMagnum firechestcomplete withdamperFiirebrick lininginside firechestLARGE FIRE OPENINGCREATED WITH MAGNUM FIRECHESTDownloadable drawings available from our web sitewww.schiedel.co.uk8
DM 54 for larger open fires and appliancesDescriptionDM 54SAP CodeWeight (kg)All dimensions are external unless otherwise stated130708545mm square casing 300mm high40129031129093300mm i/d 420 x 420 starter flue block 150mm high345mm i/d 420 x 420 starter flue block 150mm high1111129033129094300mm i/d 420 x 420 flue block 300mm high345mm i/d 420 x 420 flue block 300mm high2222130735800mm square corbel for brickwork 75mm high57130733130734670mm square capping for render950mm square capping for brickwork2046129038129092300mm i/d 545 x 635 offset block (86mm, 30 offset) 150mm high345mm i/d 545 x 635 offset block (86mm, 30 offset) 150mm high(allow 38mm distance to combustibles on offset chimneys)4440129043300mm i/d 545mm square support block 100mm high30129039300mm i/d (365mm o/d) stainless steel adaptor130732Raincap (with fixing rods for top ring)135093Top Ring (for ventilation)DM AccessoriesDescriptionACCESSORIESSAP CodeWeight (kg)All dimensions are external unless otherwise stated1464321500 x 215 x 70mm support lintel Max load (per pair) 1650kg130689Stainless steel casing wall tie130771Lip glue (5kg)51026291m reinforcement rod 12mm diameter1519
Typical DM Installation DetailFOUNDATIONSConstruction begins by providing a suitable foundationand constructional hearth in accordance with BuildingRegulations and site requirements.OPEN FIRE OPTIONBed the base plate of the firechest onto a suitablefoundation/constructional hearth in accordance withBuilding Regulations and at the level required on site usingIsokern lip glue.Install the firechest using lip glue making sure all elementsare level. 100mm of brick/blockwork must be built aroundthe sides and back of the firechest to comply with BuildingRegulations. The inside of the firechest must be finishedwith a suitable fireback or firebrick slips.Install the gather using lip glue making sure all the elementsare level. The front face of the gather can be finished withplasterboard, rendered or clad in masonry. Lintels maybe required above the gather to help carry the brick orblockwork.The maximum loading capacity of the ISOKERNfirechest and gather is 2500kg.STOVE IN RECESS OPTIONPre-stressed lintels or a suitable cast-in-situ concrete slabmust be provided above the stove recess, please make surethey are strong enough to carry the load (see appropriateIsokern DM drawing for aperture size). It is recommendedto have a minimum of 600mm of stove flue pipe beforeconnecting to the support block.The support block is bedded onto the lintels using a weakmix mortar. A stainless steel adaptor is used to create apositive connection from the support block to the stoveflue pipe (fibre rope should be used to create a seal).LintelsSupportblockStainless steeladaptorGather elementsMagnum firechestFirebrick slipsSuitable foundationOPEN FIRE OPTIONTIMBER FRAME SOLUTIONFor timber framed solutionrefer to pages 21 - 22STOVE IN RECESS OPTIONFREE STANDING STOVE OPTIONA soot door casing and access flue block must be usedbelow the flue pipe entry. The DM 45 access kit is thenused for the connecting flue pipe. A suitable wall sleevemust be used to seal the cavity wall. Any combustibleinsulation within the wall must then be kept away fromthe single wall connecting flue pipe by at least 1.5 x itsdiameter. Fibre rope is used to seal between the flue pipeand wall sleeve, a suitable trim collar can be used to finishthe inner wall surface.Flue entry kitWall sleeve andfibre rope sealPrima flue pipeSoot door casingFREE STANDING STOVE OPTIONIGNIS-PROTECT 45 VERSION10
Typical DM Installation DetailCHIMNEY CONSTRUCTIONBed the first outer casing using lip glue making sure therebate (raised lip) is uppermost. The starter flue block isthen put inside the casing bedded with lip glue. The socketon the starter flue block must be uppermost and the airgap between the starter flue and the casing should be keptclear. The finished lip glue joints should be 2-3mm thick, aspecial bag is provided for ease of application and the lipglue should be applied in 12-15 mm beads.Lip glueOn a rendered stack with a top ring fitted (see p.12 forexample), where a straight chimney passes through a flooror roof, zero mm distance to combustibles can be applied.A sliding joint is made using mineral wool or similar noncombustible material. In all other cases, 38mm clearancemust be maintained between the outer face of thechimney and any structural timber or loose combustiblematerial. Floor boards, skirting boards, dado rails and othernon-structural components may, however, be in contactwith the chimney.Inner flue blocksLip glueVoid to bekept clearNon combustiblematerial38mm clearance fromstructural timberHOW TO USE LIP GLUEOffset blocks ‘if required’ must be used immediatelyabove the support block or firechest gather. (They cannotbe used higher up the chimney.) They must be gluedtogether with lip glue and be fully supported. Please notea chimney should be built straight wherever possible. Astarter flue block will be required above the offset blocksto stagger the joints between the outer casing and innerflue blocks.External chimneys must be tied to the structure atmaximum intervals of 1.5m and at the point where itdeparts from the roof using 2 x suitable stainless steel wallties. These are fitted into the outer casing joints. They arenot always required for internal chimneys. Please consultthe Isokern technical office.Stainless steel tiesStarter flue blockOffset blocks mustbe fully supportedand bedded withlip glueDM outer casingsLoad bearingsupportCasings and flue blocks are added using lip glue for alljoints. Ensure the air gap between the inner flue and outercasing remains clear.The outer surface of the casings to befinished with plasterboard on dabs or plaster. The side thatfaces the wall does not need an external finish.High tensile steel reinforcement rods will be required for allchimneys with a height that exceeds 1.4m above the roofline, 1.1m if the wind speed exceeds 44ms. These rods areavailable from Isokern and must be grouted (1:3 cement/sand) into the holes provided in the outer casings.You muststart the rods at least the same height below the roof aswhat’s above, please check with our technical department.Reinforcement rodsPlasterboardDM outer casing11
Typical DM Installation DetailRENDERED STACK OPTIONCode 4 lead flashing to be fitted at roof level as per BuildingRegulations. We recommend that you scorch a 5-10mmdeep channel into the outer surface of the casings and foldin the top edge of the flashing.Finish the outer surface of the casings above the roofwith 2 part waterproof render. The recommended mixis 1:2:5-6 cement:lime:sand for the undercoats. 1:2:8-9cement:lime:sand for the final coat. The number of coatsrequired will depend upon the degree of exposure,generally a two coat mix is acceptable. The mix may varydue to climate conditions, the thickness of any one coatshould not exceed 15mm, and each subsequent coatshould be reduced by approximately 3mm.Isokern concrete capping for render to be lip glued ontothe last casing.10mm gapfor ventilationunder Top RingCapping for renderWaterproof renderCode 4lead flashing(not supplied)RENDERED STACKBRICK STACK OPTIONTo take brick or stonework externally a corbel is fitted justbelow the roof. Use trusses and trimmers to brace thecladding as it passes through the roof.Code 4 lead tray with 50mm upstands and stepped flashingto be fitted in accordance with Building Regulations. A50mm upstand should be fitted tight to the outside of theflue block and where possible turned in by approx 10mm.Lead trays should be coated with bituminous paint whereit is in contact with mortar. The D.P.C. tray should be fittedat least 150mm above the lowest point of intersectionwith the roof. Weep holes should be provided at the frontof the stack above the tray for water drainage.Casings can be deleted above the corbel if stack height isless than 1.4m above the roof.12Flue block orchimney potLead trayand flashingWeep holesabove trayCorbel for brick stackBRICKWORK STACKTERMINATIONRaincap - Ventilated Option - (Installation with 0 distanceto combustibles for straight rendered chimneys only).Take the last flue block up through the capping, do not fillthe gap between the flue block and capping. Push fit thealuminium top ring onto the flue block and make sure thereis a 10mm air gap between the outer edge of the ring andthe capping. The flue block may need cutting to suit.Chimney Pot Option - This option always requires a 38mmdistance to combustibles from the outside of the block. Fita chimney pot at least 75mm down into the capping andflaunch with 1:3 cement and sharp sand to seal around. Thisoption is not possible if 0 distance to combustibles is required.AFTER COMPLETIONAfter installation is complete tests and checks should becarried out in accordance with document J of the BuildingRegulations. A chimney notice plate must be completedand permanently fixed in the dwelling, ideally near theelectrical consumer unit. The checklist and notice plate areavailable from Schiedel Isokern.USE AND MAINTENANCEThe chimney should be left for at least 72 hours beforeuse, then start only with small fires for the first week andgently increase thereafter.The chimney should be swept at least twice a year, oncebefore the heating season and once after the heatingseason. You may need to sweep during the heating seasondepending upon use. The brush should be a mediumdensity polypropylene bristle type and should be the samediameter as the flue. Steel brushes must not be used tosweep the Isokern pumice flues.Always follow the appliance manufacturer’s operatinginstructions. Always burn approved fuels or dry seasonedwood. Avoid burning unseasoned wood and slow burningof solid fuels as this can produce excessive soot andcondensation which in turn cause soot fires and damage. Ifcorrectly installed, operated and maintained these systemscould last the life of the dwelling.
Liner System - for new and existing chimneysThe pumice liner system comes in a range of 15 diameters from 150mm to 1000mm with T Liners,Liner Support Blocks, and Adaptors for ease of connection to the appliance.The insulated flue linerfor traditional buildSuitable for use with inserts, stoves, open fires andsolid fuel/oil cookers.Lightweight materials, easy to handleHighly insulating pumice for better draw andminimum heat loss600mm and 1000mm lengths mean fewerjoints and fast to install15 flue sizes availableGood resistance to temperature variations givesthe maximum performance for your applianceSand/cement flaunchingaround flue liner orchimney potLead tray and flashingStructural timber40mm from outsideof chimney or 200mmfrom inside of flue linerJoints sealed with lip glueStandard flue liners withsocket uppermostVoid filled with Lecainsulation mixSupport block and adaptorfor connection to flue pipeCast in situ slab tosupport chimneyGlass fronted inset fire7N blockworkSupport block forstove connection100 x 65mm lintelsSupport plateINSET FIREDownloadable drawings available from our web site140 x 140mm lintelsFREE STANDING STOVEwww.schiedel.co.uk13
LINERS AND ACCESSORIESLiners and AccessoriesSAP CodeDescriptionWeight (kg)All dimensions are external unless otherwise statedRound 9567129738129927130142150mm i/d 600mm high rebated liner (200mm o/d)175mm i/d 600mm high rebated liner (235mm o/d)200mm i/d 600mm high rebated liner (250mm o/d)225mm i/d 600mm high rebated liner (285mm o/d)250mm i/d 600mm high rebated liner (310mm o/d)300mm i/d 600mm high rebated liner (360mm o/d)350mm i/d 600mm high rebated liner (416mm o/d)400mm i/d 1000mm high rebated liner (470mm o/d)450mm i/d 1000mm high rebated liner (530mm o/d)500mm i/d 1000mm high rebated liner (590mm o/d)600mm i/d 1000mm high rebated liner (706mm 356150mm steel collar175mm steel collar200mm steel collar225mm steel collar250mm steel collar300mm steel collar350mm steel collarSupport Lintel1464311500 x 140 x 140mm support lintels Max load (per pair) 3250kgSupport Plates (for supporting liners and support blocks)127694210mm i/d 340mm square 4mm thick(fits 150mm support blocks)128549255mm i/d 360mm square 4mm thick(fits 175mm and 200mm support blocks)1481112141619275060701007133Liner Support Blocks (for connection to appliances)126366150mm i/d 310mm square 75mm high126483175mm i/d 350mm square 75mm high127340200mm i/d 350mm square 75mm high130731225mm i/d 440mm square 100mm high128548250mm i/d 440mm square 100mm high129043300mm i/d 545mm square 100mm high788202030T Liners126376126500127695126375150mm i/d 45 rebated T liner 600mm high175mm i/d 45 rebated T liner 600mm high200mm i/d 45 rebated T liner 600mm high150mm i/d 90 rebated T liner 600mm high15202215Leca13076950 litre Leca (0.05m3)Lip Glue130771Lip glue (5kg)approx. 195
Liners and AccessoriesDescriptionLINERS AND ACCESSORIESSAP CodeWeight (kg)All dimensions are external unless otherwise statedLiner Bends126364126365126367150mm i/d 15 rebated bend150mm i/d 30 rebated bend150mm i/d 45 rebated bend456126495126496126497175mm i/d 15 rebated bend175mm i/d 30 rebated bend175mm i/d 45 rebated bend568127679127680127681200mm i/d 15 rebated bend200mm i/d 30 rebated bend200mm i/d 45 rebated bend568127706127707127708225mm i/d 15 rebated bend225mm i/d 30 rebated bend225mm i/d 45 rebated bend7811128542128531128532250mm i/d 15 rebated bend250mm i/d 30 rebated bend250mm i/d 45 rebated bend899129015129016131819300mm i/d 15 rebated bend300mm i/d 30 rebated bend300mm i/d 45 rebated bend101112129354129355131820350mm i/d 15 rebated bend350mm i/d 30 rebated bend350mm i/d 45 rebated bend131417Larger diameter bends available on request.Stainless Steel Adaptors with Sealing Rope (for connection to support block)126373150mm i/d (205mm o/d)126499175mm i/d (235mm o/d)127691200mm i/d (255mm o/d)127719225mm i/d (290mm o/d)128547250mm i/d (315mm o/d)129039300mm i/d (365mm o/d)Stainless Steel Increaser Adaptors with Sealing Rope (for connection to support block)126357125-150mm i/d (205mm o/d)126493150-175mm i/d (235mm o/d)127671150-200mm i/d (255mm o/d)127672175-200mm i/d (255mm o/d)127704200-225mm i/d (290mm o/d)Stainless Steel Adaptors with Sealing Rope (for connection to T liners)125453125-150mm i/d (210mm o/d)126358150mm i/d (210mm o/d)146412150-175mm i/d (240mm o/d)146413175mm i/d (240mm o/d)15
LINERS AND ACCESSORIESLiners and AccessoriesSAP CodeDescriptionWeight (kg)All dimensions are external unless otherwise statedAccess Blocks126362150mm i/d 215mm square 205mm highrebated access block200mm i/d (also for 175mm) 280mm square 280mm highrebated access block5Soot Door142837Double soot door 265 x 395mm2Insulated Plug142599Insulated plug (glue to access blocks)4127678Chimney 73713073813073916Terracotta150mm i/d roll top terracotta 450mm high200mm i/d roll top terracotta 450mm high225mm i/d roll top terracotta 300mm high225mm i/d roll top terracotta 450mm high250mm i/d roll top terracotta 450mm high300mm i/d roll top terracotta 450mm high350mm i/d roll top terracotta 450mm highBuff150mm i/d roll top buff 450mm high200mm i/d roll top buff 450mm high225mm i/d roll top buff 300mm high225mm i/d roll top buff 450mm high250mm i/d roll top buff 450mm high300mm i/d roll top buff 450mm high350mm i/d roll top buff 450mm high130742130740130741TerracottaTopguard terracotta 150-250mm i/dTopguard terracotta 300mm i/dTopguard terracotta 350mm i/dBuffTopguard buff 150-250mm i/dTopguard buff 300mm i/dTopguard buff 350mm i/dNotice Plate130696Chimney notice plateSmoke Pellets130817Smoke pellets (6 per tube)121416121819263214161218192632222222
Typical Liner Installation DetailConstruction begins by providing a suitable foundationand constructional hearth in accordance with BuildingRegulations and site requirements.45 T linerSTOVE IN RECESS OPTIONOur pre stressed lintels must be installed above thefireplace recess , for this method a support plate is requiredunder the support block.45 Wall sleeveSoot doorAlternatively a suitable cast-in-situ concrete slab lintelcan be created above the fireplace recess. (See Isokernstandard drawings for hole size depending on diameter ofchosen flue).The support block is bedded ontothe slab lintel using weak mix mortar.A stainless steel adaptor is used toconnect from the support block tothe stove flue pipe. This adaptor ispushed up onto the support blockspigot (fibre rope should be used tocreate a seal). It is recommended tohave a minimum of 600mm lengthof flue pipe before connecting tothe chimney.FREE STANDING STOVE OPTIONOPEN FIRE OPTIONInstall the firechest onto the constructional hearth using lipglue making sure all elements are level. 100mm of brick orblockwork must be built around the sides and back of thefirechest to comply with Building Regulations. The inside ofthe firechest must be finished with a suitable fireback orfirebrick slips.7N blockworkSupport block forstove connection100 x 65mm lintelsSupport plate140 x 140mm lintelsSTOVE IN RECESS OPTIONInstall the gather using lip glue making sure all elementsare level. The front face of the gather can be finished withplasterboard, rendered or clad in masonry. Lintels maybe required above the gather to help carry the brick orblockwork. The maximum loading capacity of the Isokernfirechest and gather is 2500kg.Voids filled withLeca mixSuitable lintelFREE STANDING STOVE OPTIONA soot door must be provided below the flue pipeentry to allow for inspection and removal of soot anddebris. A suitable wall sleeve is to be used to seal thecavity wall. Any combustible insulation within the wallmust be kept away from the single skin connecting fluepipe by at least 1.5 x its diameter.A stainless steel adaptor is fittedto the Isokern T Liner with thefibre tape supplied. The flue pipe isa push fit over the spigot on theadaptor. Seal off the gap betweenthe flue pipe and wall sleeve withfire proof rope and closing plate.Magnum firechestFirebrick liningOPEN FIRE OPTION17
Typical Liner Installation DetailALL OPTIONSThe flue liners are installed socket uppermost andsealed with Isokern lip glue. Finished lip glue jointsshould be 2-3mm thick. A special bag is provided forease of application and the lip glue should be applied in12-15mm beads. Remove any excess glue to maintain asmooth surface. Clad the liners with a minimum of 100mmthick brickwork or medium density (7kN) blockwork.A minimum thickness of 15mm leca insulation must beinstalled between the liners and masonry. Mix 20 partsleca to 1 part opc cement and a small amount of water.Make sure it is well mixed before using.ueGlLipFit appropriate lead dpc’s and flashings in accordance withthe relevant regulations. Isokern recommend that the leadtray should be dressed up the outside of the flue liners toavoid a weak joint. Weep holes should be provided abovethe tray for moisture drainage.Terminate the chimney to the correct height in accordancewith document J of the Building Regulations. The chimneycan be finished by flaunching (1:3 cement/sharp sand)either around the Isokern flue liner or a suitable chimneypot. Approved rain caps can be used to help prevent waterentering the flue.Liner orchimney potFlaunchingLiners with socketuppermostJoints sealedwith lip glueDirection offlue gasesWeep holesabove trayLead trayand flashingLeca insulationIf bends are required in the chimney make sure adequatesupport is provided and always backfill with leca insulationmix. Liners can be cut between bends to achieve a requiredoffset distance. A steel collar as well as lip glue must beused for any cut joints. A maximum of 2 complete offsets(4 bends) are allowed
Isokern Pumice Double Module DM is CE Certified to EN1858 TÜV Cert no. 0036 CPR 90219 001 Isokern Pumice Chimney Liner is CE certified to EN1857 TÜV Cert no. 0036 CPR 90219 002 Isokern Magnum Firechest has been tested at the Fraunhofer Institut, Stuttgart, Cert no. P8-094/2006
Forge 300 Dell PowerEdge R610 Dell PowerEdge R620 RAID 1 Forge 500 Dell PowerEdge R710 Dell PowerEdge R720 RAID 5 Forge 700 Dell PowerEdge R720 Dell PowerEdge R730xd RAID 6 A Forge Field Rebuild Kit, containing: Forge OVF template files forge-esx5- kit-version .xxx-provider.iso This Field Rebuild gu
THE ISOKERN MAGNUM SERIES (ALL FUEL) Fan the flames of innovation and take your fireplace to new heights. The Isokern Magnum Series Fireplace System product line offers the largest openings available in the market, with finished width openings of 36”, 42”, 48”, 60” & 72”.
Isokern Pumice Double Module DM is CE Certified to EN1858 TÜV Cert no. 0036 CPD 90219 001 Isokern Pumice Chimney Liner is CE certified to EN1857 TÜV Cert no. 0036 CPD 90219 002 Isokern Magnum Firechest has been tested at the Fraunhofer Institut, Stuttgart, Cert no. P8-094/2006
Valley Forge Military Academy & College PARENTS HANDBOOK 2018-2019 Opening Day The Ring Ceremony Graduation! 2. 3 VALLEY FORGE MILITARY ACADEMY & COLLEGE 1001 Eagle Road, Wayne, PA 19087-3695 / 610-989-1200 / FAX: 610-975-9642 OFFICE OF THE PRESIDENT Dear Valley Forge Parents,
Valley Forge National Park Service U.S. Department of the Interior Valley Forge National Historical Park "officers and men are chiefly in Hutts, which they say is tolarable comfortable," Martha Washington to Mercy Otis Warren, Camp Valley Forge, 7 March 1778. By Marc A. Brier August 1, 2004 Tolerably Comfortable: A Field Trial of a Recreated
Old Forge Council, Borough of Old Forge Police Department, and Borough of Old Forge Civil Service Commission; and (4) the claim for punitive damages against the Borough of Old Forge. Judge Munley denied the motions to dismiss in all other respects. (Doc. 38).
Operation WARRIOR FORGE Supplemental Training Guide This guide is designed to augment Warrior Forge training and is based on input and experience gathered from previous years. Supplemental training addresses skills Cadets will require to successfully execute Warrior Forge. The intent is for Cadre to review this material
Peter Norvig Prentice Hall, 2003 This is the book that ties in most closely with the module Artificial Intelligence (2nd ed.) Elaine Rich & Kevin Knight McGraw Hill, 1991 Quite old now, but still a good second book Artificial Intelligence: A New Synthesis Nils Nilsson Morgan Kaufmann, 1998 A good modern book Artificial Intelligence (3rd ed.) Patrick Winston Addison Wesley, 1992 A classic, but .
