Vecoax Ultra RF Series Modulator Manual

2y ago
13 Views
2 Downloads
1.52 MB
47 Pages
Last View : 18d ago
Last Download : 2m ago
Upload by : Ophelia Arruda
Transcription

VECOAX ULTRA RF SERIES MODULATORMANUALUSER MANUAL

Pro Video InstrumentsNOTE: BEFORE INSTALLATIONPlease test each unit UNMOUNTED ON A TEST BENCH with your TestTV before installing your units to ensure you are receiving the TestPattern signal. Then Program your unit.This makes troubleshooting easier.This can be done simply by connecting your TV with a short piece ofCoax cable to the RF out of the Unit. No HDMI needs to be connectedfor this test.This will display our test pattern on your TV.By default our unit is set to QAM(J.83B Cable) mode.This can be changed by refering to our QUICK GUIDE below.Depending on your supported TV standards, scan for digital channels.Please refer below for our QUICK GUIDE to setting up your device foryour application and needs.Vecoax Ultra RF series modulator Manual1

Pro Video InstrumentsPRODUCT SPECSPower - 120v/AC. Environment Ambient Temp Max/Min 0 to 70 C 30-65% humidityAll Major TV Encoder standards built-in. No need to reprogram or flash the unit to adifferent Format.QAM (J.83B Digital Cable), ATSC (Digital Over the Air Channels), ISDBTb, DVBT, DVBC,DMBT Set via Color DisplayModulator Design allows for Future upgradesUniversal HDMI inputs works with any HDMI video sources and closed captionInjects directly on the existing TV Cables with other channels (This depends on theAvailable Frequencies for your Coax Network.)Customize channel names & numbersIntegrates with any TV Control AutomationDelivers perfect Full HD up to Signal at any distance (depend on video source quality)Ultra-Low latency provides the ability to use menus on your HDMI source with ease.Works with many different TV brands including Samsung, Sony, Vizio, LG, and More.Easy Plug and Play Setup with customization options available in the easy to use menuvia a Color Display.Works With any HD Video HDMI EDID compatible source.*(720P or 1080P/I FixedResolution 59.94 Frames)Can be mixed with other HDTV signals such as Digital Cable or Over the Air Channels*(depending on Frequencies available for you to use)Vecoax Ultra RF series modulator Manual2

Pro Video InstrumentsModular – Expandable – Reliable - 5 Year Warranty - AffordablePOWERING THE DEVICE. – QUICK GUIDE – USA/CANADA1. It is recommended to test the device first on a test bench for yourapplication before making it a permanent installation to your system sotroubleshooting is easier.2. Connect your included Power Cord to the unit.3. Once the unit is powered on you will see the main menu.Vecoax Ultra RF series modulator Manual3

Pro Video Instruments4. First, Connect a short piece of coax cable to your TV’s tuner and the otherend to the unit’s TV out RF connector.Vecoax Ultra RF series modulator Manual4

Pro Video Instruments5. On the unit press the enter button to enter the menu of that ChannelHighlighted. Once you press enter you be on the main screen of the channelyou have selected. Press enter again to go into the menu system for thatchannel to change the options. In the menu system of your selected channelthe second option would be TV Standard.ChannelSelectionMenuSelectedChannelMain nceMenuVecoax Ultra RF series modulator Manual5

Pro Video InstrumentsSet your standard you require to use. If you are unsure most newer TV’s 3 years andabove accept both ATSC(over the air channel) and QAM(J.83B Digital Cable). PleaseRefer to your TV owner’s manual6. By default, the unit is set to QAM (J.83B Digital Cable) Mode Preset 1 with a Frequency of 303.000 MHz which is Channel 37 for the first channelinput. The TV will Scan for the Frequency and pick up the channels on Cable.Depend on your model will determine the channels picked up.7. Auto Scan for Channels on your TV. Depending on your Location andSupported TV standards for your TV such as QAM (J.83B Digital Cable) orATSC (Digital over the Air) will determine the Standard you need to set onthe unit. Please Refer to CUSTOMIZATION below to change these settings.8. Once the channel is found it will display our Test Pattern when no HDMI isconnected to the unit.Vecoax Ultra RF series modulator Manual6

Pro Video InstrumentsQUICK GUIDE – USA/CANADA – CONT.9. We can use the Major/Minor channels on the unit’s settings to force changethe channel number that is displayed & stored/referred to on your TV. Bydefault, this is 1.1: Major 1, Minor 1. You may change this if you like to 38.1:Major 38, Minor 1. This will display and be stored as channel 38.1 on yourTV.10.Once we see our Test Pattern on the Channel found on your TV, you mayinsert your HDMI source. Please ensure that your HDMI source such as aDVD player or DirecTV STB is set to a Fixed Resolution of 1080P/I or 720P.11.Once you have inserted a valid HDMI Video Signal into the HDMI port TheBlue On-air LED on the front will Stay steady lit.12.You should now see the video playing on you Channel.13.If you wish to change the name of the channel that is displayed, you may doso under the Short name settings of the unit. 4-6 Characters max is alloweddepending on your TV.14.More detail information can be found below if more customization isrequired.Vecoax Ultra RF series modulator Manual7

Pro Video InstrumentsNOTE: If the above is not working, please check the following1.2.3.4.All connections are correctUnits settings are correct for your applicationCorrect TV standard is set for your TV such as ATSC, QAM, DVB-TEnsure your video source is valid or set to a correct fixed resolution. Please refer toyour HDMI source owner’s manual on how to set a fixed resolution.5. Try with another TV with no HDMI connected to ensure you are getting a signal.6. Try lowering the RF level of the channels which can be found under the Advance Menu RF Level (digital attenuation)To reset the unit’s settings to default, Please go to the in the advance menu of the unit called“RESET.” Press enter to reset that channel to default.You may Also Recall the default PRESETS by hitting ESC until you are on the Main Page of theunits screen with the Word PRESET. Press enter on the selected Preset to make the unitautomatically adjust the settings of all the channels to its defined settings.If the “ON-AIR,” LED does not stay steady, please ensure your HDMI source is set to a fixedresolution of 1080P or 720P 59.94 Frames and connected directly to the Unit.Ensure your Device is passing EDID correctly If you are using a Splitter, some splitters don’tsupport EDID pass-through (Extended Display Identification Data used to tell the source or TVwhat video resolution is supported) Test your HDMI source without the Splitter connected.For SDI to HDMI EDID is a MUST! SDI does not carry EDID information so a converter withEDID injection is a MUST!Vecoax Ultra RF series modulator Manual8

Pro Video InstrumentsCUSTOMIZATION AND PARAMETERSEach unit is ready to work plug n play by default. After connecting the unit using ourQUICK GUIDE above you may customize the unit to your liking such as Frequency,Major and Minor channel numbers, Short name, or TV standard. You can also use ourPresets built into the unit which will set the unit up for you.These units come with Presets to make Plug and Play setup a Breeze. Simply Select thePreset number you wish and it enter. The unit will default it to the set Settingsprogrammed into the unit. This is useful for multiple units on the same Coax Network.Further Tweaking can be made afterwards.PRESET MENUPreset menu can be found by pressing esc button when at the Channel selection menuas shown belowVecoax Ultra RF series modulator Manual9

Pro Video InstrumentsQAM (J.83B DIGITAL CABLE)These are the Defaults andGood starting point for PLUGN PLAY setup.If you have more than oneunit please ensure you changethe FREQUENCY,MAJOR/MINOR, and SHORTNAME so they don’t overlapand create issues. SOURCE – Set your Video Source HDMI,CVBS, or SDI depending on your model STANDARD – Set your TV standarddepending on your needs, location, andsupport format of your TV. FREQ – Set your Frequency using ourFrequency chart listed at the end of themanual. TV’s will scan for the Frequency andthe Frequency Channel it relates to firstbefore being stored using the Major/MinorChannel you have set on the Unit. This iscalled the VCT(Virtual Channel Table) VID QUALITY – Set the Latency Mode ofyour Video. MOD – Modulation Mode you wish to use.QAM64 is the default and works with 99% ofTV’sQAM256 is used in applications that requireit such as with other coax systems that useQAM 256 or only support QAM 256 mode.QAM 256 also allows more bandwidth whichresults in smoother and Sharper picture. Ifyou’re TV does not work in QAM 256 Pleaserevert back to QAM 64 mode.Main Screen – this displays ashort version of the currentsettings the unit isbroadcasting onVecoax Ultra RF series modulator Manual10

Pro Video InstrumentsQAM (J.83B DIGITAL CABLE) –CONT.Short Name – you will see thismenu when changing theshort name of your channel MAJOR CHANNEL – This is the number thatwill be displayed and stored into the TV Ifyou wish to display a different number thanwhat the ACUTAL Channel is per FrequencyChart. EXAMPLE: 783MHZ is channel 122. Wecan have it Stored as Channel 1.1 on the TVso when we use the TV Remote and press 1It will know to go to Frequency 783MHZ todisplay your PVI Channel. MINOR CHANNEL – This is your Sub channelNumber. By default 1 is fine. If you wish tohave many channels with the same Majornumber ex. 10 you would use the Minor tocreate Sub channels ex. 10.1 10.2 10.3 10.4etc. SHORT NAME – Name of the Channel youwish to use. 4-6 Characters max dependingon TV. AUDIO FORMAT – Set your desired AudioFormat. AC3 is the Default Standard for ATSCand QAM mode. ADVANCE – Advance options for users whorequire Specific PID’s or Fixed EDIDinformation. Please don’t change theseunless you understand your required PID’s orEDID per Cable Provider instructions or PVITech Support request.Vecoax Ultra RF series modulator Manual11

Pro Video InstrumentsADVANCE MENU – ADVANCE USERS ONLYThese are the DefaultsPlease don’t change theseunless you have anunderstanding of PID’s orrequire a specific PID set byyour Service provider for CoaxSTB injection.Changing these numbers cancreated unwanted effects toyour channel. DEFAULT – used tofactory reset the unit todefault. SERVICE ID – Used to ID the TransportStream PMT PID - Program Map Table used toprovide information on each programpresent in the transport stream, includingthe program number, and list theelementary streams VIDEO PID – Video ID uses in the TransportStream to Identify the video inside thepacket identifier AUDIO PID - Audio ID uses in the TransportStream to Identify the video inside thepacket identifier 1080P CONVERSION – Used to Downscale1080P (Progressive) signals to 1080i(Interlace) to Support older TV’s that don’tsupport 1080P signals through the Tuner. Ifyou know your TV supports 1080P throughthe tuner you may switch this to 1080P toreceive the full 1080P signal from your 1080PVideo Source. RF ATTENUATION – Default is 0DB which isthe full strength 40 DBmv from the unit. Ifyou require it to be lower set the RFattenuation higher. The higher the numberthe lower the signal strength will be. Ex RFattenuation 10 would be 30 /- DBmv signal. FIXED EDID – This will force the unit to onlysupport a specific resolution so your HDMIsource is forced to only output at thatresolution set. Usual for HDMI sources thatchange resolution on the fly ex DirecTV GeneBoxes or other Cable provider STB’s.Vecoax Ultra RF series modulator Manual12

Pro Video InstrumentsATSC (OVER THE AIR CHANNEL)These are the Defaults andGood starting point for PLUGN PLAY setup.If you have more than oneunit please ensure you changethe FREQUENCY,MAJOR/MINOR, and SHORTNAME so they don’t overlapand create issues. ADVANCE – Advanceoptions for users whorequire Specific PID’s orFixed EDID information.Please don’t changethese unless youunderstand yourrequired PID’s or EDIDper Cable Providerinstructions or PVI TechSupport request. SOURCE – Set your Video Source HDMI,CVBS, or SDI depending on your model STANDARD – Set your TV standarddepending on your needs, location, andsupport format of your TV. FREQ – Set your Frequency using ourFrequency chart listed at the end of themanual. TV’s will scan for the Frequency andthe Frequency Channel it relates to firstbefore being stored using the Major/MinorChannel you have set on the Unit. This iscalled the VCT(Virtual Channel Table) VID QUALITY – Set the Latency Mode ofyour Video. MAJOR CHANNEL – This is the number thatwill be displayed and stored into the TV Ifyou wish to display a different number thanwhat the ACUTAL Channel is per FrequencyChart. EXAMPLE: 473MHZ is channel 14. Wecan have it Stored as Channel 1.1 on the TVso when we use the TV Remote and press 1It will know to go tune to Frequency 473MHZto display your PVI Channel. MINOR CHANNEL – This is your Sub channelNumber. By default 1 is fine. If you wish tohave many channels with the same Majornumber ex. 10 you would use the Minor tocreate Sub channels with the same Major ex.10.1 10.2 10.3 10.4 etc. SHORT NAME – Name of the Channel youwish to use. 4-6 Characters max dependingon TV. AUDIO FORMAT – Set your desired AudioFormat. AC3 is the Default Standard for ATSCand QAM mode. Vecoax Ultra RF series modulator Manual13

Pro Video InstrumentsDVB-T GENERIC – PLEASE REFER TO YOUR LOCATION NEEDSThese are the Defaults andGood starting point for PLUGN PLAY setup.If you have more than oneunit please ensure you changethe FREQUENCY and LCN sothey don’t overlap and createissues. ADVANCE – Advanceoptions for users whorequire Specific PID’s orFixed EDID information.Please don’t changethese unless youunderstand yourrequired PID’s or EDIDper Cable Providerinstructions or PVI TechSupport request. SOURCE – Set your Video Source HDMI,CVBS, or SDI depending on your model STANDARD – Set your TV standarddepending on your needs, location, andsupport format of your TV. FREQ – Set your Frequency using ourFrequency chart listed at the end of themanual. TV’s will scan for the Frequency andthe Frequency Channel it relates to firstbefore being stored using the LCN BW – Bandwidth can be changed for yourregions requirements.EU/NEW ZEALAND 8 MHzAUSTRALIA 7 MHzCOLOMBIA\PANAMA 6 MHz VID QUALITY – Set the Latency Mode ofyour Video. MOD – Modulation Mode which you can setto match your region’s needs. FTT – Fast Fourier Transform can be set heredepending on your needs and region. Thiscontrols number of carriers per a givenbandwidth GI – Guard interval can be set here CR – code rate which controls carrier tonoise ratio LCN – logical channel number can be sethere. This is the channel number that will bestored and displayed on the TV AUDIO – Default is MPEGVecoax Ultra RF series modulator Manual14

Pro Video InstrumentsDVB-CThese are the Defaults andGood starting point for PLUGN PLAY setup.If you have more than oneunit please ensure you changethe FREQUENCY, LCN, andSERVICE NAME so they don’toverlap and create issues. SOURCE – Set your Video Source HDMI,CVBS, or SDI depending on your model STANDARD – Set your TV standarddepending on your needs, location, andsupport format of your TV. FREQ – Set your Frequency using ourFrequency chart listed at the end of themanual. TV’s will scan for the Frequency andthe Frequency Channel it relates to firstbefore being stored using the Major/MinorChannel you have set on the Unit. This iscalled the VCT(Virtual Channel Table) VID QUALITY – Set the Latency Mode ofyour Video. MOD – Modulation mode can be set heredepending on your needs for your regionfrom 16- to 256-QAM LCN – logical channel number can be sethere. This is the channel number that will bestored and displayed on the TV SERVICE NAME – Name of the Channel youwish to use. 4-6 Characters max dependingon TV. AUDIO FORMAT – Set your desired AudioFormat. AC3 is the Default Standard for ATSCand QAM mode. ADVANCE – Advance options for users whorequire Specific PID’s or Fixed EDIDinformation. Please don’t change theseunless you understand your required PID’s orEDID per Cable Provider instructions or PVITech Support request.Vecoax Ultra RF series modulator Manual15

Pro Video InstrumentsISDBTThese are the Defaults andGood starting point for PLUGN PLAY setup.If you have more than oneunit please ensure you changethe FREQUENCY, KEY ID, andSERVICE NAME so they don’toverlap and create issues. SOURCE – Set your Video Source HDMI,CVBS, or SDI depending on your model STANDARD – Set your TV standarddepending on your needs, location, andsupport format of your TV. FREQ – Set your Frequency using ourFrequency chart listed at the end of themanual. VID QUALITY – Set the Latency Mode ofyour Video. KEY ID – This is the number that will bedisplayed and stored into the TV SERVICE NAME – Name of the Channel youwish to use. 4-6 Characters max dependingon TV. AUDIO FORMAT – Set your desired AudioFormat. AC3 is the Default Standard for ATSCand QAM mode. ADVANCE – Advance options for users whorequire Specific PID’s or Fixed EDIDinformation. Please don’t change theseunless you understand your required PID’s orEDID per Cable Provider instructions or PVITech Support request.Vecoax Ultra RF series modulator Manual16

Pro Video InstrumentsDTMBThese are the Defaults andGood starting point for PLUGN PLAY setup.If you have more than oneunit please ensure you changethe FREQUENCY, LCN, andSERVICE NAME so they don’toverlap and create issues. SOURCE – Set your Video Source HDMI,CVBS, or SDI depending on your model STANDARD – Set your TV standarddepending on your needs, location, andsupport format of your TV. FREQ – Set your Frequency here. Because ofthe wide range that DTMB coversdetermines the Frequencies available. Pleasesearch for these online for you region. VID QUALITY – Set the Latency Mode ofyour Video. MODE – Modulation mode can be set heredepending on your needs for your region LCN – logical channel number can be sethere. This is the channel number that will bestored and displayed on the TV SERVICE NAME – Name of the Channel youwish to use. 4-6 Characters max dependingon TV. AUDIO FORMAT – Set your desired AudioFormat. AC3 is the Default Standard for ATSCand QAM mode. ADVANCE – Advance options for users whorequire Specific PID’s or Fixed EDIDinformation. Please don’t change theseunless you understand your required PID’s orEDID per Cable Provider instructions or PVITech Support request.Vecoax Ultra RF series modulator Manual17

Pro Video InstrumentsINSTALLING MULTIPLE UNITSTo install multiple units on the same coax network, make sure to CHANGE theFrequencies, Major/Minor, and Short Name of each Channel BEFORE you connectthem to the same coax network, so there will be no Channel Conflicts. By default eachunit will be set the same. This can easily be done using the Preset Menu option on theMain Menu of the unit or changing them manually.Please Test each unit directly connected to a Test TV first with a short piece of coaxBEFORE making it a permanent installation such as a Rack mount to maketroubleshooting easier. Once you have all your units’ setup test again with a test TVfirst before combining the units with your coax network.If you have other modulators or Digital signals you must find a harmony between theRF levels and Frequency’s that are available such as ATSC (Over the Air Antenna)signal. Please refer to your other modulators settings to find the frequencies thepopulated and set your unit to a different set. Please see combining ATSC/QAMsignals in our manual below for more information about combining with other DigitalSignals from ProvidersTo change the Frequencies of each module, press enter button the unit to enter themenu. Navigate using the keys to FREQ. Press enter and use the navigation keys tochange the numbers. The frequency is in Kilohertz. So 783Mhzs would be 783000 kHzon the unit. Once you have set the Frequency press enter and then move on tochanging the Major/Minor channel as well as the short name if you wish. Once youhave set all your settings press ESCAPE. This will prompt you to save your changes.Use the navigation keys to Highlight Yes and press Enter. The unit will now go back tothe main screen and restart the encoder. Once the unit saves the settings you will see“transmitting,” and a Solid Blue LED on the “ON-AIR.”Write down these values or channel numbers, or put a sticker on each unit with thenew assigned frequency and channel Number so it will be easy to troubleshoot theunit in future without the need to reset it or dismantle everything. Depending on yoursetup it’s suggested to use an active splitter or combiner with more than 6 units, 40 TV’s or using multiple splitters(each splitter will lower the DB level 5-10dbs dependingon the quality) to ensure you get a clear signal to all your TV’s no matter the distance.Vecoax Ultra RF series modulator Manual18

Pro Video InstrumentsIf your system works without one then it is not necessary. Again this is a Suggestionand not required for operation of your devices.COMBINING SERIVCE PROVIDERS SIGNALS OR ATSC WITH YOUR DEVICEFor Combining ATSC (Over the Air channels) you must find the frequencies that areused by your local stations. This information can usual be found online by searchingfor, “(insert your local area) ATSC frequency chart.” This will give you a nice table thatshows all the Frequencies used in your area. Find the ones that are not used and writethose down. Set your device(s) to those unused frequencies. Test using your Test TV.Note: For installers it is recommend but not required to use a Spectrum analyzer tosee the spectrum available to you to make the installation easier. This does notrequire an expensive unit to do this. Any Spectrum tester to view the availablefrequencies will help you in the process.For combining with cable Service provider the same rules apply. You can contact yourlocal service provider of your basic cable to find the frequencies that they use and findthe ones that are available for you to use. If you wish to inject into a Digital CableConverter box or STB (set-top box) most of the time the service provider will include achannel you may broadcast onto or some providers require a specific PID’s to be setwhich can be set in the ADVANCE MENU in order for the Set to box to be able to readthe channel.Vecoax Ultra RF series modulator Manual19

Pro Video InstrumentsAUDIO ENCODING SETTINGSThe unit has three standards of Audio Encoding. Depending on your local and supportedformat per TV you can set the following: AC3 – 2.1 Dolby Digital Audio US/Canada Standard for Broadcasting MPEG – MPEG 2 Layer II used in DVB-T EU Standard. ACC - Advanced Audio Coding or MPEG-4. Used in some ATSC broadcastsand ISDBT format. Supported by Most TV’s worldwide.If your HDMI source has Compressed Audio or Dolby Digital Enabled it isrecommended to set your HDMI source to Stereo PCM or Uncompressed Audioto ensure you get a clean audio signal to your TV. Double compression can causea lot of audio skipping issues.Vecoax Ultra RF series modulator Manual20

Pro Video InstrumentsVID QUAILTY MODESThe Vid Quality modes on the unit determine the speed and size of information sentto your TV’s tuner decoder. Default is LOW LATENCY. Only if you experience anyimage issue on the TV should you change this setting. Using the other optionsavailable such as HIGH or Average will only changes the speed the information is givento the TV to be able to decode the picture properly ( For slower Television tuners andmodels )LOW LATENCY - This mode is the fastest in terms of information sent to the TV. Itsends frame by frame which will give you the best picture and ultra-low delay forapplications that require constant use of the HDMI Source menu system such as Cableprovider boxes or DVD players.AVERAGE – This is a good balance between lower latency and speed of informationsent to your TV’s tuner. This mode sends the Information in smaller chunks ratherthan instant refresh rate which helps with slower TV tuners that have slower/smallerdecoder memory. This form of chucks can help give a very slight increase in imagequality due to the Tuner having time to decode each picture at its own pace.HIGH - This mode sends the Information in Lager chunks than Average mode whichagain can help with slower TV tuners that have slower/smaller decoder memory. Thisform of chucks can help give a very slight increase in image quality due to the Tunerhaving more time to decode each picture at its own pace before the next set of chunksare received.Note: A higher delay will occur with these modes due to the delivery of theinformation to the tuner in form of chucks rather than picture by picture.Vecoax Ultra RF series modulator Manual21

Pro Video InstrumentsFUTURE CONTENT HEREVecoax Ultra RF series modulator Manual22

Pro Video InstrumentsTROUBLESHOOTINGNOT RECEIVING SIGNAL TO MY TV. WHY?Please check your settings of the unit and ensure the correct standard is set. Check allyour connections and scan for the standard you have set on the unit. Example QAM –Scan for Digital Cable on your TVI plugged my unit up and it’s not working? – Please follow our Quick Guide for settingup the unit. Double check your connections as well. Ensure the Signal is not too Strongfor your TV tuner.“ON-AIR” LED IS BLINKINGCheck the HDMI source Resolution and please ensure you have a FIXED resolution set.Please refer to your HDMI source Owner’s Manual on setting a Fixed Resolution andnot auto. The unit see’s your video but cannot accept the resolution to encode it forcoax usage your TV tuner can understand.UNIT WON’T POWER ON?Check your included power adapter. Ensure that you have a solid connection and theDC jack is screwed on correctly.I SEE THE TEST PATTERN BUT NO VIDEO IS PLAYING!? WHY?Check your HDMI connection. Check the HDMI source Resolution and please ensureyou have a FIXED resolution set. Please refer to your HDMI source Owner’s Manual onsetting a Fixed Resolution and not auto. Test with a different Video source such as aDVD player or FireTV stick.Vecoax Ultra RF series modulator Manual23

Pro Video InstrumentsI HAVE 2 UNITS HOW DO I SET THEM UP TO WORK TOGETHER?Please refer to our “Installing Multiple Units,” guide above or use the Preset MenuWHAT ARE THE BEST SETTINGS FOR THE BEST QUALITY VIDEO?Depending on your Region will determine your settings that need to be set. The unitalready outputs a great quality video.For people who want the best we recommend for USA/Canada to use QAM(J.83B)when available as this will give you the highest bitrate possible as well as using MOD QAM256 set on you unit which will increase the bandwidth of the signal allowingmore information to flow.Set your HDMI source to 1080pSet your Unit to 1080P Mode - Advance options - 1080P Conversion - AutoThis will allow the 1080P signal to pass. If your TV tuner does not support 1080Pthrough the tuner you will not receive any signal or video. If this happens switch itback to “Interlacing.”Depending on if you care about the low latency mode or not you can change the VidQuality to “HIGH.” A very slight change in image quality will happen as well as anincrease in delay between menus GUI’s due to the information handling sent to yourTV. Please refer to Vid Quality settings in the manual above for more information.Vecoax Ultra RF series modulator Manual24

Pro Video InstrumentsMY PICTURE LOOKS GREAT UNTIL THERE IS FAST MOTION –This could be an “interlacing,” issue with 1080i mode. This happens a lot with sports.Some TV’s don’t like Interlacing trough the tuner causing “Ghosting.” Change yourHDMI source to 1080P (progressive) or 720P as well as on the unit 1080P Mode - Advance options - 1080P Conversion - AutoThis will allow the 1080P signal to pass. If your TV tuner does not support 1080Pthrough the tuner you will not receive any signal or video. If this happens switch itback to “Interlacing,” and use 720PTry changing the VID QUALITY settings as well to help with slower Tuners or if usingQAM (J.83B) switch your MOD from QAM64 to QAM256 if supported by your TV.HOW DO I MIXED MY UNIT WITH OTHER DIGITAL SIGNALSPlease refer to the, “MIXING SIGNALS WITH OTHERS,” in our manual aboveMY VIDEO IS STRETCHED OUT ON THE TVOur unit has a passive HDMI meaning it only encodes what the video is being sent tothe unit. It does not change the color or Aspect ratio of the video to your TV. Pleasecheck your HDMI source or TV aspect Settings.HOW DO I REPLACE AN OLD MODULATOR WITH THIS ONEDepending on how your old modulator was set up will determine how you will setyour new unit up. Please refer to your settings of the modulator you are replacing andcopy the settings as best as possible such as Frequencies, Channel Number, Name, etc.Please refer to the, “CUSTOMIZATION SETTINGS,” above.Vecoax Ultra RF series modulator Manual25

Pro Video InstrumentsI AM LOOSING OTHER CHANNELS IN MY COAX NETWORK WHEN I TURN ON THEPVI UNITCheck to ensure you are not broadcasting on the same frequency as other signals.Please refer to our, “MIXING SIGNALS WITH OTHERS,” guide above. It could be thatour unit is oversaturating the other signals as well because of the strength of thesignal. Try lowering the RF level under the, “ADVANCE MENU.” Using attenuatorsworks as well or amplification of the other signal such as antenna signal coming inbefore combining it in your coax network.WHAT ARE ALL THE STANDARDS ON THE UNIT AND WHAT DO THEY MEANEach region in the world uses its own Standard that they have adopted. You can checkthe standards that are uses in your area online. At the moment this is the currentstandards used according to our Sources. You can refer to each Standard and how toset your unit to these standards above.USA TV CABLE J83B modeUSA TV AIR ATSC modeEU/CO/NZ/AU DVBTLATIN AMERICA ISDBCHINA DTMBEU DVB-CI AM FEEDING A 1080P SIGNAL BUT MY TV SAYS ITS 1080ISet your Unit t

Works with many different TV brands including Samsung, Sony, Vizio, LG, and More. Easy Plug and Play Setup with customization options available in the easy to use menu via a Color Display. Works With any HD Video HDMI EDID compatibl

Related Documents:

behringer ultra-curve pro dsp 24 a/d- d/a dsp ultra-curve pro ultra- curve pro 1.1 behringer ultra-curve pro 24 ad/da 24 dsp ultra-curve pro dsp8024 smd (surface mounted device) iso9000 ultra-curve pro 1.2 ultra-curve pro ultra-curve pro 19 2u 10 ultra-curve pro ultra-curve pro iec . 7 ultra-curve pro dsp8024 .

MODULATORS AND 1-F AMPLIFIERS . Mobile Modulator-25-Watt Modulator-60-MC 1-F Amplifier-25-Watt Modulator-100-Watt Modulator-I2.5-MC 1-F Amplifier -5.5-MC 1-F Amplifier-JO-MC 1-F Amplifier SECTION 5 MISCELLANEOUS CIRCUITS Signaling System-Mobile Public-Address System-5-Watt 150-MC Amplifier-Squelch Amplifier-I60-MC Power Amplifier-Auto

Hummer’s Meritor Wabco ABS Modulator The code 2-6 gives a shuttle valve switch failure as the cause and the fix is to replace the entire modulator assembly. Following the service manual it is not too difficult to remove the modulator: Unplug battery, Remove drivers side splash shield, 3 bolts. Remove horn bracket/disconnect horns, 2 bolts.

47 117493 SCREW, mach, hex washer hd 2 48 BOX, control 276868 Ultra 395/495 1 15D313 Ultra 595 1 49 CONTROL, board, 110V 1 246379 Ultra 395/495 1 248179 Ultra 595 1 50 276882 COVER, control 1 51 15K393 LABEL, control, Graco 1 56 CORD, power 1 15J743 Ultra 395/495, Stand 1 15D029 Ultra 595, L

TABLE OF CONTENTS: XPRESS ULTRA FIELD TERMINATION CONNECTORS SC Xpress Ultra Fiber Connectors Page 2 LC Xpress Ultra Fiber Connectors Page 3 ST Xpress Ultra Fiber Connectors Page 3 CLEANING & INSPECTION Optical Connector Contamination Pages 5 - 6 Xpress Ultra Cleaner Pages 7 - 8 Xpress Ultra Cleaner Replaceable Cartridge Page 8 Xpress Ultra

Frequency chart starting on page 22. TVs will scan for the Frequency, then store the channel as the Major/Minor channel number you have set on the Unit. VID QUALITY – Set the Latency Mode of your Video. MOD – Modulation Mode you wish to use. QAM64 is the default and works with 99% of TVs

Subject: Solid-State Modulator Testing In this note is reported the testing of the pre-production version of a solid-state adder type modulator. In this configuration, the adder consists of transformers that are driven by an array of MOSFET switches that are connected in parallel but not in series; i.e. the inputCited by: 1Publish Year: 2000Author: E. G. Cook

AMERICAN BOARD OF RADIOLOGY, ) ) CLASS ACTION ) Trial by Jury Demanded Defendant. ) CLASS ACTION COMPLAINT Plaintiff Sadhish K. Siva, (“Plaintiff”), for his Complaint against Defendant American Board of Radiology (“ABR” or “Defendant”) hereby alleges as follows: INTRODUCTION 1. This case is about ABR’s illegal and anti-competitive conduct in the market for initial board .