Pressure Washer Operator’s Manual - Lowes Holiday

WARNING The high pressure stream of waterthat this equipment produces could cutthrough skin and its underlying tissues,resulting in serious injury and possibleamputation.Spray gun traps high water pressure, even whenengine is stopped and water is disconnected, whichcould result in serious injury. If cut by fluid, call physician immediately. DO NOT treatas a simple cut. DO NOT allow CHILDREN to operate pressure washer. NEVER repair high pressure hose. Replace it. NEVER repair leaking connections with sealant of anykind. Replace o-ring or seal. NEVER connect high pressure hose to nozzle extension. Keep high pressure hose connected to pump and spraygun while system is pressurized. ALWAYS point spray gun in safe direction, press redbutton and squeeze spray gun trigger to release highpressure, every time you stop engine. NEVER aim spray gun at people, animals, or plants. DO NOT secure spray gun in open position. DO NOT leave spray gun unattended while machine isrunning. NEVER use a spray gun which does not have a triggerlock or trigger guard in place and in working order. Always be certain spray gun, nozzles and accessoriesare correctly attached.WARNING Unintentional sparking could causefire or electric shock resulting in deathor serious injury.WHEN ADJUSTING OR MAKING REPAIRS TO YOURPRESSURE WASHER Disconnect the spark plug wire from the spark plug andplace the wire where it cannot contact spark plug.WHEN TESTING FOR ENGINE SPARK Use approved spark plug tester. DO NOT check for spark with spark plug removed.WARNING Starter and other rotating partscould entangle hands, hair, clothing, oraccessories resulting in serious injury. NEVER operate pressure washer without protectivehousing or covers. DO NOT wear loose clothing, jewelry or anything thatcould be caught in the starter or other rotating parts. Tie up long hair and remove jewelry.WARNING Risk of eye or bodily injury.Spray could splash back or propelobjects resulting in serious injury. Always wear indirect vented (chemical splash) safetygoggles marked to comply with ANSI Z87.1 when usingor in vicinity of this equipment. NEVER substitute safety glasses or dry-conditiongoggles for indirect vented safety goggles. Always wear protective clothing such as a long-sleevedshirt, long pants and close-toed shoes. NEVER operate pressure washer when barefoot orwearing sandals or shorts.CAUTION Excessively high operating speedscould result in minor injury.Excessively low speeds impose a heavy load. DO NOT tamper with governor spring, links or otherparts to increase engine speed. Pressure washersupplies correct rated pressure and flow when running atgoverned speed. DO NOT modify pressure washer in any way.NOTICE High pressure spray could damage fragileitems including glass. DO NOT point spray gun at glass when using red (0 ) spray tip. NEVER aim spray gun at plants.NOTICE Improper treatment of pressure washercould damage it and shorten its life. If you have questions about intended use, ask dealer orcontact qualified service center. NEVER operate units with broken or missing parts, orwithout protective housing or covers. DO NOT by-pass any safety device on this machine. DO NOT tamper with governed speed. DO NOT operate pressure washer above rated pressure. DO NOT modify pressure washer in any way. Before starting pressure washer in cold weather, check allparts of the equipment to be sure ice has not formed there. NEVER move machine by pulling on hoses. Use handleprovided on unit. This equipment is designed to be used with Briggs &Stratton Power Products authorized parts ONLY. Ifequipment is used with parts that DO NOT comply withminimum specifications, user assumes all risks andliabilities.5

AssemblyRead entire operator’s manual before youattempt to assemble or operate your newpressure washer.Your pressure washer requires some assembly and isready for use after it has been properly serviced withthe recommended oil and fuel.If you have any problems with the assembly of yourpressure washer, please call the pressure washerhelpline at (888) 611-6708. If calling for assistance,please have the model, revision, and serial numberfrom the identification label available.Unpack Pressure Washer1. Remove the parts bag, accessories, and insertsincluded with pressure washer.2. Open carton completely by cutting each cornerfrom top to bottom.3. Ensure you have all included items prior toassembly.Items in the carton include: Main Unit with Cleaning Tank Handle High Pressure Hose Spray Gun Nozzle Extension with Quick Connect Fitting Plastic Accessory Tray Oil Pouch Engine Operator’s Manual Parts Bag (which includes the following): Operator’s Manual Bag of 5 Multi–Colored Quick Connect SprayTips Handle/Accessory Tray Fastening Hardware Kit(which includes): Carriage Bolts (2) Plastic Knobs (2) Tree Clips (4)To prepare your pressure washer for operation,you will need to perform these tasks:1. Attach handle and accessory tray to main unit.2. Add oil to engine crankcase.3. Add fuel to fuel tank.4. Connect high pressure hose to spray gun andpump.5. Connect water supply to pump.6. Attach nozzle extension to spray gun.7. Select/attach quick connect spray tip to nozzleextension.6Attach Handle and Accessory Tray1. Place handle (A) onto handle supports connectedto main unit. Make sure holes in handle align withholes on handle supports.BCA2. Insert handle carriage bolts (B) through holes frominside of unit and attach a plastic knob (C) fromoutside of unit. Tighten by hand.NOTICE By loosening both knobs to the unthreadedmiddle section of the attachment bolt, the upper handlecan fold forward to store flat atop the cold engine.DO NOT fold the handle down while the engine is hot.3. Place accessory tray (D) over holes (E) on handle(viewing from front of unit). Push the tree clips(F) into the holes until they sit flat against theaccessory tray.DFE Add Engine Oil and Fuel Place pressure washer on a level surface. Refer to engine operator’s manual and follow oiland fuel recommendations and instructions.NOTICE Any attempt to crank or start theengine before it has been properly filled with therecommended oil will result in equipment failure. Refer to engine manual for oil and fuel fill information. Damage to equipment resulting from failure to follow thisinstruction will void warranty.NOTICE Check oil often during engine break–in. Referto engine operator’s manual for recommendations.www.troybilt.com

Lubricate O-RingsLubrication of o-rings is extremely important forinstallation and operation. The use of a lubricant(petroleum or synthetic grease) during assembly helpsseat o-rings properly and provides an improved seal. Italso helps protect the o-ring from damage by abrasion,pinching or cutting and extends the life of the o-ring.NOTICE ALWAYS apply a small amount of lubricanton o-rings prior to assembling the garden hose to thepump (A), high pressure hose (B), spray gun (C), andnozzle extension (D).CLubricate all connections shown below, followingthese instructions:1. Inspect and clean connecting surfaces prior tolubrication and assembly.2. Use lubricants sparingly during assembly; a lightfilm is all that is required.3. Use a small brush or cotton swab to apply greasedirectly to o-rings where they are not accessible(QC fitting, M22 fitting).DBA7

Connect Hose and Water Supply to PumpNOTICE DO NOT run the pump without the watersupply connected and turned on. Damage to equipment resulting from failure to follow thisinstruction will void warranty.NOTICE Remove and discard the shipping caps fromthe pump’s high pressure outlet and water inlet beforeattaching hoses.1. Uncoil high pressure hose and attach one end ofhose to base of spray gun. Tighten by hand.WARNING The high pressure stream of waterthat this equipment produces could cutthrough skin and its underlying tissues,resulting in serious injury and possibleamputation. NEVER connect high pressure hose to nozzle extension. Keep high pressure hose connected to pump and spraygun while system is pressurized. Always be certain spray gun, nozzles and accessoriesare correctly attached.2. Attach other end of high pressure hose to highpressure outlet on pump. Tighten by hand.3. Before connecting garden hose to water inlet,inspect inlet screen (A). Clean screen if it containsdebris or have it replaced if damaged. DO NOTrun pressure washer if inlet screen is damaged.ANOTICE Using a One Way Valve (vacuum breakeror check valve) at pump inlet could cause pump orinlet connector damage. There MUST be at least 10 ft. (3 m) of unrestricted gardenhose between the pressure washer inlet and any device,such as a vacuum breaker or check valve. Damage to equipment resulting from failure to follow thisinstruction will void warranty.5. Connect the garden hose (not to exceed50 ft. (15 m) in length) to the water inlet. Tightenby hand.WARNING Risk of eye injury.Spray could splash back or propel objectsresulting in serious injury. Always wear indirect vented (chemical splash) safetygoggles marked to comply with ANSI Z87.1 when usingor in vicinity of this equipment. NEVER substitute safety glasses or dry-conditiongoggles for indirect vented safety goggles.6. Turn ON the water, press red button (B) on thegun and squeeze the trigger to purge the pumpsystem of air and impurities.BChecklist Before Starting EngineReview the unit’s assembly to ensure you haveperformed all of the following.1. Be sure to read Operator Safety and Operationbefore using pressure washer.2. Make sure handle is in place and secure.3. Check that oil has been added to proper level inthe engine crankcase.4. Add proper fuel to fuel tank.5. Check for properly tightened hose connections.6. Check to make sure there are no kinks, cuts, ordamage to high pressure hose.7. Provide a proper water supply at an adequateflow.4. Run water through your garden hose for30 seconds to clean out any debris.NOTICE DO NOT siphon standing water for the watersupply. Use ONLY cold water (less than 100 F (38 C)).8www.troybilt.com

Features and ControlsRead this Operator’s Manual and safety rules before operating your pressure washer.Compare the illustrations with your pressure washer, to familiarize yourself with the locations of variouscontrols and adjustments. Save this manual for future reference.AB , CTSRPNDMLEJ , KFG , HA - Spray Gun — Controls the application of wateronto cleaning surface with trigger device. Includestrigger lock.B - Recoil Starter — Used for starting the enginemanually.C - Oil Fill/Dipstick — Check and fill with oil here.D - Engine Identification — Provides model, typeand code of engine. Please have these readilyavailable if calling for assistance.E - High Pressure Outlet — Connection for highpressure hose.F - Water Inlet — Connection for garden hose.G - Pump — Develops high pressure.H - Automatic Cool Down System — Cycles waterthrough pump when water reaches 125 -155 F(51 C-68 C). Warm water will discharge frompump onto ground. This system prevents internalpump damage.J - Cleaning Tank — Use to hold up to 0.5 gallons(1.9 liters) of pressure washer detergent.K - Identification Label — Provides model and serialnumber of pressure washer. Please have thesereadily available if calling for assistance.L - Air Filter — Protects engine by filtering dust anddebris out of intake air.M - Warning/Operating Instructions Tag —Identifies hazards and proper procedure to start/stop pressure washer.N - Fuel Tank — Fill tank with regular unleaded fuel.Always leave room for fuel expansion.P - Nozzle Extension with Quick Connect — Allowsyou to switch between five different spray tips.R - High Pressure Hose — Connect one end to waterpump and the other end to spray gun.S - Accessory Tray — Provides convenient storagefor standard and optional accessories, such asbrushes, turbo wands, etc.T - Spray Tips — Jet soap, Jet flush, 0 , 25 and 40 :for various high pressure cleaning applications.Items Not Shown:Engine Controls — See engine manual for details onengine controls.9

OperationIf you have any problems operating your pressurewasher, please call the pressure washer helpline at(888) 611-6708.Pressure Washer LocationCarbon Monoxide PoisoningWARNING POISONOUS GAS HAZARD.Engine exhaust contains carbon monoxide,a poisonous gas that could kill you inminutes. You CANNOT smell it, see it, ortaste it. Even if you do not smell exhaust fumes, youcould still be exposed to carbon monoxide gas. Operate this product ONLY outside far away fromwindows, doors and vents to reduce the risk of carbonmonoxide gas from accumulating and potentially beingdrawn towards occupied spaces. Install battery-operated carbon monoxide alarms orplug-in carbon monoxide alarms with battery back-upaccording to the manufacturer’s instructions. Smokealarms cannot detect carbon monoxide gas. DO NOT run this product inside homes, garages,basements, crawlspaces, sheds, or other partiallyenclosed spaces even if using fans or opening doorsand windows for ventilation. Carbon monoxide canquickly build up in these spaces and can linger for hours,even after this product has shut off. ALWAYS place this product downwind and point theengine exhaust away from occupied spaces.If you start to feel sick, dizzy, or weak while using thisproduct, get to fresh air RIGHT AWAY. See a doctor. Youmay have carbon monoxide poisoning.How to Start Your Pressure WasherTo start your pressure washer for the first time,follow these instructions step-by-step. This startinginformation also applies if you have let the pressurewasher sit idle for at least a day.1. Place pressure washer near an outside watersource capable of supplying water at a flow rategreater than 3.7 gallons (14.0 liter) per minute andno less than 20 PSI (1.4 BAR) at pressure washerend of garden hose. DO NOT siphon supplywater.2. Check that high pressure hose is tightlyconnected to spray gun and pump. See Assemblysection.3. Make sure unit is in a level position.4. Connect garden hose to water inlet on pressurewasher pump.NOTICE DO NOT run the pump without the watersupply connected and turned on. Damage to equipment resulting from failure to follow thisinstruction will void warranty.5. Turn ON water, point gun in a safe direction, pressred button and squeeze trigger to purge pumpsystem of air and impurities.6. Attach nozzle extension to spray gun. Tighten byhand.7. Choose spray tip you want to use, pull back oncollar of nozzle extension, insert spray tip andrelease collar. Tug on spray tip to make sure it issecurely in place. See .NOTICE Before starting the pressure washer, be sureyou are wearing safety goggles as described below.Risk of Fire ClearancesWARNING Exhaust heat /gases could ignitecombustibles, structures or damage fueltank causing a fire, resulting in death orserious injury. Keep at least 5 ft. (1.5 m) clearance on all sides ofpressure washer including overhead.10WARNING Risk of eye injury.Spray could splash back or propel objectsresulting in serious injury. Always wear indirect vented (chemical splash) safetygoggles marked to comply with ANSI Z87.1 when usingor in vicinity of this equipment. NEVER substitute safety glasses or dry-conditiongoggles for indirect vented safety goggles.www.troybilt.com

8. When starting engine, position yourself asrecommended and start engine according toinstructions given in engine operator’s manual.Also see operating instructions tag located on thepressure washer.9. Return starter grip handle slowly. DO NOT letrope “snap back” against starter.WARNING The high pressure stream of waterthat this equipment produces could cutthrough skin and its underlying tissues,resulting in serious injury and possibleamputation.Spray gun traps high water pressure, even whenengine is stopped and water is disconnected, whichcould result in serious injury. DO NOT allow CHILDREN to operate pressure washer. Keep high pressure hose connected to pump and spraygun while system is pressurized. NEVER aim spray gun at people, animals, or plants. DO NOT secure spray gun in open position. DO NOT leave spray gun unattended while machine isrunning. NEVER use a spray gun which does not have a triggerlock or trigger guard in place and in working order. Always be certain spray gun, nozzles and accessoriesare correctly attached.WARNING Starter cord kickback (rapidretraction) will pull hand and arm towardengine faster than you can let go whichcould cause broken bones, fractures,bruises, or sprains resulting in serious injury. NEVER pull starter cord without first relieving spray gunpressure. When starting engine, pull cord slowly until resistance isfelt and then pull rapidly to avoid kickback. After each starting attempt, where engine fails to run,always point spray gun in safe direction, press red buttonand squeeze spray gun trigger to release high pressure. Firmly grasp spray gun with both hands when using highpressure spray to avoid injury when spray gun kicksback.WARNING Exhaust heat /gases could ignitecombustibles, structures or damagefuel tank causing a fire, resulting indeath or serious injury.Contact with muffler area could cause burnsresulting in serious injury. DO NOT touch hot parts and AVOID hot exhaust gases. Allow equipment to cool before touching. Keep at least 5 ft. (1.5 m) of clearance on all sides ofpressure washer including overhead. It is a violation of California Public Resource Code,Section 4442, to use or operate the engine on any forestcovered, brush-covered, or grass-covered land unlessthe exhaust system is equipped with a spark arrester, asdefined in Section 4442, maintained in effective workingorder. Other states or federal jurisdictions may havesimilar laws.Contact the original equipment manufacturer, retailer,or dealer to obtain a spark arrester designed for theexhaust system installed on this engine. Replacement parts must be the same and installed in thesame position as the original parts.11

How to Stop Your Pressure Washer1. Release spray gun trigger and let engine idle fortwo minutes.2. Turn engine off according to instructions given inengine operator’s manual.3. ALWAYS point gun in a safe direction and pressred button and squeeze spray gun trigger torelease retained high water pressure.WARNING The high pressure stream of water thatthis equipment produces could cut throughskin and its underlying tissues, resulting inserious injury and possible amputation.Spray gun traps high water pressure, even whenengine is stopped and water is disconnected, whichcould result in serious injury. Keep high pressure hose connected to pump and spraygun while system is pressurized. ALWAYS point spray gun in safe direction, press redbutton and squeeze spray gun trigger to release highpressure, every time you stop engine.How to Use Accessory TrayThe unit is equipped with an accessory tray withplaces to store your spray gun, nozzle extension, highpressure hose and quick connect spray tips.1. Place nozzle extension in slots on left side ofaccessory tray (viewing from rear of unit) and snap in.2. Place spray gun through grooves on right side ofaccessory tray.3. Insert multi-colored spray tips in holes provided onfront of accessory tray.How to Use Spray TipsThe quick–connect on the nozzle extension allows youto switch between five different quick connect spraytips. Spray tips can be changed while pressure washeris running once spray gun trigger lock is engaged. Thespray tips vary the spray pattern as shown.Follow these instructions to change spray tips:1. Pull bac

always point spray gun in safe direction, press red button and squeeze spray gun trigger to release high pressure. Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks Back. WARNING Exhaust heat/gases could ignite combustibles, st