DRS Compression Connectors - Cableandwireshop

2y ago
14 Views
2 Downloads
5.20 MB
11 Pages
Last View : 21d ago
Last Download : 3m ago
Upload by : Ronnie Bonney
Transcription

TRS Compression ConnectorsInstallation Guide 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Products for Installation TrainingCompression ConnectorPCT-TRS-6¼” x ¼” Prepared Coaxial CableCompression ToolCombination Compression ToolPCT-TRS-CTPCT-TRS-CT-AS2PagePage2 2 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Preparing the Coaxial Cable Prepare coaxial cable with a ¼” x ¼” cable trimming tool.Remove trimmed jacket from cable.For trishield cable: Remove the outer layer of foil (Figure 1).For quad cable: Fold back the first layer of braid, remove the outerlayer of foil, and fold back the second layer of braid.To reduce cable insertion force: Evenly flare and separate the wirebraid (Figure 2).Figure 1Figure 23PagePage3 3 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Installing Prepared Cable on PCT’s TRS Push the connector straight on so that the cable dielectric is properlyaligned inside the connector mandrel.A slight back and forth twist can be used to ease the cable insertion.Avoid excessive twisting.The cable dielectric should be flush with the bottom of the nut(Figures 1 & 2).Figure 1Figure 2Cable Dielectric4PagePage4 4 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Tips for Difficult Installations The compression tool can be used to add leverage when pushing theconnector onto cable (Figure 1).For cable that is hard to insert, be sure to evenly spread and flare thebraid material.Remember that twisting the connector can make installation moredifficult. Push the connector straight on to the cable.Figure 15PagePage5 5 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Using the Compression Tool(PCT-TRS-CT) With the handle in the open position and the cable gate flipped open,place the cable and connector into the tool against the plunger tip(Figure 1).Close the cable gate.The cable and connector will now be in the proper position (Figure 2).CableGatePlungerFigure 1Figure 26PagePage6 6 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Compressing the Connector¾ To compress the connector, close the tool handle completely,ensuring the connector sleeve is fully compressed.7PagePage7 7 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Using the Combination Tool(PCT-TRS-CT-AS)SERIES 59/6: With the handle in the open position and the cable gate flipped open, place the cableand connector into the tool against the plunger tip (Figure 1).Close the cable gate (Figure 2).Figure 1Figure 28PagePage8 8 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

Using the Combination Tool(PCT-TRS-CT-AS)SERIES 7/11/320QR: Swing the front gate out completely until magnet engages (Figure 1).Flip open the cable gate and place the cable and connector into the tool (Figure 2).Close cable gate (Figure 3).Figure 1Figure 2Figure 39PagePage9 9 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

DRS 7 & 11 As cable is inserted, the pin will extend forward“Pop-out” center pin confirms proper center conductor contactUniversal cable application (60% through quad)Pin extends past thenut once the cable isfully inserted10PagePage1010 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

TRS/DRS Connector GuidePart T-TRS-CTPCT-TRS-CT-ASSeries 6 PlenumPCT-TRS-6PPCT-TRS-CTPCT-TRS-CT-ASSeries 7, 60% thru CT-DRS-320QRPCT-TRS-CT-ASCable TypeSeries 59, 60% thru QuadSeries 59 HeadendSeries 6, 60% thru QuadSeries 11, 60% thru QuadSeries QR320Universal Seal RingPCT-TRS-CTPCT-TRS-CT-ASPCT-SR11PagePage1111 3-Aug-09 PCT International, Inc. All rights reserved. Proprietary. Restricted use per company permission.

PCT-DRS-11. PCT-TRS-CT-AS: Universal Seal Ring. PCT-SR: PCT-TRS-CT PCT-TRS-CT-AS. Title: DRS Compression Connectors Aut

Related Documents:

SSMA Connectors End Launch Connectors 2.40 mm Connectors Adapters 2.92 mm Connectors TNC Connectors Super SMA Connectors N Series Connectors 54 End Launch Connectors Dimensions End Launch Connector Dimensions Field Replaceable .375" Square Flange Connectors are Available in Male or Female Configurations. Standard Profile Connectors Low .

SSMA Connectors End Launch Connectors 2.40 mm Connectors Adapters 2.92 mm Connectors TNC Connectors Super SMA Connectors N Series Connectors 54 End Launch Connectors Dimensions End Launch Connector Dimensions Field Replaceable .375" Square Flange Connectors are Available in Male or Female Configurations. Standard Profile Connectors Low .

DRS PCT-DRS-6 Series 6, 60% - Trishield Black PCT-DRS-6P Series 6, Plenum Cable White PCT-DRS-6Q Series 6, Quad Violet PCT-DRS-59 Series 59, 60% - Trishield Orange PCT-DRS-59Q Series 59, Quad Green PCT-DRS-59P Series 59, Plenum Cable White PCT-DRSHE-59 Series 59, Headend Cable Yellow PCT PCT PCT PCT PCT PCT PCT SERIES 6 & 59 BNC PART NO .File Size: 445KB

Each panel will hold up to six connectors each. The box has a capacity of 24 dual SC connectors, single SC connectors, dual LC connectors, ST connectors, M-series type copper connectors, BNC connectors, F-type connectors, or any combination thereof. Connector types can be mixed and matched within the box by using two different panels.

DRS Power & Control Technologies with the products and capabilities of DRS Marlo Coil, DRS Pivotal Power and DRS Power Technology. In addition to expanding the offerings found in this catalog, you will find full color photos of our products, and site specific contact informa

DRS-PCT. Any changes to this quality management system must be submitted to DRS-PCT for review and approval prior to implementation in accordance with this purchase order. Unless otherwise noted on the purchase order, all verification of purchased products will be conducted upon receipt at DRS-PCT per DRS

Understanding DRS' Equations. DRS is like a table that sits atop a single leg at its center. Each side of that table represents a host in your cluster. That leg can only support the table when all sides are balanced. DRS' job is to relocate VMs to ensure the table stays balanced. Every five minutes a DRS interval is invoked.

Abrasive jet Machining consists of 1. Gas propulsion system 2. Abrasive feeder 3. Machining Chamber 4. AJM Nozzle 5. Abrasives Gas Propulsion System Supplies clean and dry air. Air, Nitrogen and carbon dioxide to propel the abrasive particles. Gas may be supplied either from a compressor or a cylinder. In case of a compressor, air filter cum drier should be used to avoid water or oil .