How To Change Serpentine Belt On Fiat Punto 199 .
How to change serpentine belt onFiat Punto 199 – replacement guideVIDEO TUTORIALImportant!This replacement procedure can be used for:FIAT 500L (351 , 352 ) 1.3 D Multijet (199LXY1A, 199LXY11), FIAT GRANDEPUNTO (199 ) 1.3 D MultijetThe steps may slightly vary depending on the car design.WWW.AUTODOC.CO.UK1–14
REPLACEMENT: SERPENTINE BELT – FIAT PUNTO 199.TOOLS YOU'LL NEED:Combination spanner #15WWW.AUTODOC.CO.UKFender cover2–14
Replacement: serpentine belt – Fiat Punto 199. Professionalsrecommend:All work should be done with the engine stopped.REPLACEMENT: SERPENTINE BELT – FIAT PUNTO 199. TAKETHE FOLLOWING STEPS:1Open the hood.WWW.AUTODOC.CO.UK3–14
2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.3Lift the car using a jack or place it over an inspection pit.WWW.AUTODOC.CO.UK4–14
4Pull aside the V-ribbed belt tensioner pulley. Use a combination spanner #15.5Remove the V-ribbed belt.6Return the tensioner pulley to its initial position. Use a combination spanner #15.WWW.AUTODOC.CO.UK5–14
Replacement: serpentine belt – Fiat Punto 199. AUTODOCrecommends:Check the condition of the tensioner pulley and idler pulley. Replacethem if necessary.7Pull aside the V-ribbed belt tensioner pulley. Use a combination spanner #15.8Install the V-ribbed belt.Replacement: serpentine belt – Fiat Punto 199. AUTODOCexperts recommend:Make sure that the V-ribbed belt fits all pulleys snugly.WWW.AUTODOC.CO.UK6–14
9Place the V-ribbed belt on the tensioner pulley.10Return the tensioner pulley to its initial position. Use a combination spanner #15.WWW.AUTODOC.CO.UK7–14
11Run the engine for a few minutes. This is necessary in order to make sure that the componentoperates properly.12Shut off the engine.13Lower the car.WWW.AUTODOC.CO.UK8–14
14Remove the fender protection cover.15Close the hood.WWW.AUTODOC.CO.UK9–14
DID YOU FIND THESE INSTRUCTIONSHELPFUL?YESNOBECOME A MEMBER OF AUTODOC CLUB!WWW.AUTODOC.CO.UK10–14
AUTODOC — TOP QUALITY AND AFFORDABLE CARPARTS ONLINEAUTODOC MOBILE APP: GREAT DEALS AND CONVENIENTSHOPPINGA GREAT SELECTION OF SPARE PARTS FOR YOUR CARWWW.AUTODOC.CO.UK11–14
BUY SPARE PARTS FOR FIATSERPENTINE BELT: A WIDE SELECTIONWWW.AUTODOC.CO.UK12–14
CHOOSE CAR PARTS FOR FIAT PUNTO 199SERPENTINE BELT FOR FIAT: BUY NOWWWW.AUTODOC.CO.UK13–14
SERPENTINE BELT FOR FIAT PUNTO 199: THE BEST DEALS &OFFERSDisclaimer:The document contains only general recommendations that may be useful for you when you perform repair or replacement work. AutoDoc shallnot be liable for any loss, injury, damage of property occurring in the repair or replacement process due to incorrect use or misinterpretation ofthe provided information.AutoDoc shall not be liable for any possible mistakes and uncertainties in this guide. The information provided is for information purposes onlyand cannot replace advice from specialists.AutoDoc shall not be liable for incorrect or hazardous usage of equipment, tools and car parts. AutoDoc strongly recommends to be carefuland observe the safety rules when performing repair or replacement works. Remember: usage of low quality auto parts does not guaranteeyou the appropriate level of road safety. Copyright 2018 – All the contents of this website, in particular texts, photographs and graphics, are protected by copyright. All rights,including reproduction, publication, editing and translation rights, are reserved by Autodoc GmbH.WWW.AUTODOC.CO.UK14–14
Fiat Punto 199 – replacement guide VIDEO TUTORIAL This replacement procedure can be used for: FIAT 500L (351_, 352_) 1.3 D Multijet (199LXY1A, 199LXY11), FIAT GRANDE PUNTO (199_) 1.3 D Multijet The steps may slightly vary depending on the car design. WWW.AUTODOC.CO.UK 1–14 Important!
Drive Belt Tensioner Drive Belt Tensioner Damper M/T Air Cleaner Duct Oil Filler Cap No.3 Timing Belt Cover Gasket No.2 Timing Belt Cover No.5 Air Hose Water Pump Pulley Drive Belt Camshaft Timing Pulley Drive Belt Tensioner Hold-Down Clamp Idler Pulley Battery Insulator Battery Tray Battery Timing Belt Gasket No.1 Timing Belt Cover Crankshaft .
Serpentine Cemetery Reserve Management Plan November 2016 version 1a 1.4 Report Structure . The Serpentine Cemetery Management Plan has been prepared to provide a clear direction for the future management and enhancement of the values of the Serpentine Cemetery. This management plan has been written in accordance with the Reserves Planning and
Conveyor belt Hole / rip FIX'N GO screws LEGEND 50 cm 50 cm 50 cm 50 cm BELT 1 BELT 2 Longitudinal rip Crosswise rips under 50% of the belt width On each side, you must have 20% of the belt width Belt edge damage under 20% of the belt width Hole up to 10 cm wide in the edge of the belt (more than 3 cm : the hole before with a piece of used .
Dayco Poly Rib serpentine belt, a Dayco automatic belt tensioner, and a Dayco idler/tensioner pulley. One part number one complete solution. Serpentine Belt Kit Dayco demanding drive kits provide all the required components to ensure a quiet, problem-free belt drive system. These kits have been designed to address the most demanding drives .
belt whip and turnover on conventional drives. 11 Super II V-Belt (A, B, C) The revolutionary raw-edge belt that blows the cover off conventional wrapped belts with its unique construction. Made of EPDM.* 12 Double-Angle Belt (AA, BB, CC) Designed for use on serpentine type drive applications. 13 Durapower ll FHP V-Belt (2L, 3L, 4L, 5L)
Remove the V-ribbed belt. Replacement: serpentine belt - Ford Focus MK2. Tip from AUTODOC: 6 Return the tensioner pulley to its initial position. Use a combination spanner #15. WWW.AUTODOC.CO.UK 5-13 Check the condition of the tensioner pulley and idler pulley. Replace them if necessary.
To place an order please use the Conveyor Request Form (page 37) or visit the online Belt Conveyor Confi guration Tool at www.robotunits.com Description Frame Width F max. 3) Belt Conveyor 40 40 mm 300 N Belt Conveyor 40 80 mm 700 N Belt Conveyor 40 120 mm 1100 N Belt Conveyor 40 160 mm 1500 N Belt Conveyor 40 200 mm 1900 N Belt Conveyor 40 .
alternator, A/C compressor and belt that are not included with a Chevrolet Performance LT1 Crate engine. This package is designed to provide you a complete serpentine belt accessory drive package for your Chevrolet Performance LT1 Crate engine. This kit is based on the accessory drive system from the 2014 Corvette.
