Snapnrack - Ozark Mountain Power
Mounting StructuresSnapNrackRoof Mounting SystemSnapNrack was developed by a team of veteran solar engineers working with installers inthe field, dedicated to overcoming the limitations of conventional racking and ensuring aquick, efficient installation. It simplifies and reduces the cost of the solar installation process.SnapNrack is a top-down roof mounting solution, load tested and engineered for up to 150mph wind speeds and 100 psf snow loads. See www.snapnrack.com for full details.SnapNrack is compatible with modules from virtually any manufacturer. Snap-in slidingchannel nuts ensure quick and easy installation and precise alignment. Mid-clamps are ahalf-inch wide to keep the math simple. Every bolt in the system uses the same size wrench,ensuring efficient installation and reducing man-hours on the roof during installation. Andthere’s no need to drill any holes in the rails to connect standoffs and L-feet. The channelsin the rail profiles can house running module leads, providing better aesthetics and improvedconductor protection.SnapNrack is engineered for durability and structural integrity in all environments, withexcellent seismic, wind, and snow loading protection. Its compact and efficient rail designreduces material requirements and ensures a low profile installation on your roof.Weather-tight flashing and standoffsfor tilt applicationsSnapNrack standoffs are height-adjustable to ensure a clean, level installation on even themost uneven roof surface. Tilt-up can be achieved with pieces of cut rail and L-feet.Rails and components have a 10-year warranty.Roof MountsYou can order complete kits below, or bulk components on the following pages.SnapNrack Tilt Leg KitsTilt angles from 0 to 15 degrees can be configured without legs by simply using SnapNrackstandoffs. Use a 5-1/2 inch standoff for the lower rail and a 7-inch standoff for the upperrail. This allows adjustability for shallow tilts.Tilt angles from 10 to 45 degrees can be configured by using standoffs for both upper andlower rails and adding an extension to the standoff supporting the upper rail using a scrapof rail cut to the appropriate length and drilled with two holes. Calculate the length of theupper rail standoff extension to provide the desired module tilt angle. Tilt leg rails can becut and drilled in advance to save time on the job site. A simple drill guide will help withlocating the holes in the tilt leg.If the length of the cut rail exceeds 4 feet, consult a structural engineer before proceeding.Order one tilt-leg hardware kit for each tilt leg required. It contains all the front and rearrail hardware needed for each leg, but does not include standoffs and rail needed to makethe legs. Order those items separately.SnapNrack Universal Roof Mount KitsSnapNrack universal roof mount kits include black anodized rail,Universal End Clamps (UEC), black mid clamps and black railend caps so they are suitable for use with black and clear framedmodules. The unique universal end clamp is not dependent onmodule frame depth like typical end clamps because they clamp thebottom of the module frame to the rail. This provides a very strongconnection and give a finished look to the end of the mounting rails.These kits will work for the number of modules listed in the tableon the next page for all of the 200 to 235 watt modules listed inthis catalog and any other brand of modules with a width of 39.5"or less. Cutting of aluminum rail may be required.The roof attachment parts are sold separately and depend on thetype of roof that the mounting structure is being attached to. Seepage 30 for SnapNrack roof attachment components.28Universal End Clampallows rails to be cut flushwith the end of the modulesSnapNrack Universal Roof Mount KitsModule Package dimensionsQuantityL" x W" x D"Item codePrice3126 x 4 x 4015-09950 2154166 x 4 x 4015-09951 2805126 x 4 x 4015-09952 3696126 x 4 x 8015-09953 4357166 x 4 x 8015-09954 5008166 x 4 x 8015-09955 5659166 x 4 x 8015-09956 65510166 x 4 x 8015-09957 719Suggested retail prices are subject to change; check with us for latest pricing.
Mounting StructuresSnapNrack Bulk PartsRails, clamp sets and roof attachment parts are sold separately below, and on the next page.Rail SetsRails are sold in pairs, as rail sets, offered in two lengths to simplify ordering. The 122-inch railset accommodates a single row of 3 modules in the 200-watt range. The 162-inch rail set willaccommodate four modules in the 200 watt range. The chart below shows which rails and howmany splice kits to use based on the number of modules to be installed in a single row. All ofthe 200 watt modules in this catalog are 39.5 inches wide or less. If you are installing 5 modulerows, each row will use one 122 inch rail set and half of a 162 inch rail set. For other modulewidths, calculate rail length for your installation and remember to add 1/2" between modules formid clamp spacing. These light-weight aluminum rails can be cut with a chop saw or circularsaw with a carbide blade, a saber saw with a metal cutting blade, or a hack saw.Item codeRail sets and splice kits to orderNumber of modules in a rowClearBlack345-678910No. of 122-inch rail sets to order015-09814015-098161021032No. of 162-inch rail sets to order015-09817015-098180101201Splice kits to order015-09961n/a0022244Standard Rail Set PricesClear aluminumFits quantity of modulesItem codePriceItem codePriceSnapNrack standard rail set 122" - clear3 module015-09814 132015-09816 163SnapNrack standard rail set 162" - clear4 module015-09817 176015-09818 217Rail cut fee includes splice kit (for UPS shipping)015-09829 30015-09829 30Splice kit - single bar with hardware015-09961 9015-09963 13Standard Top-Mount Clamp sets for fastening the PV modules to the railFor each row of modules we suggest you buy a 3-module clamp set plus two additional mid clamps for each additional module inthe row. Choose your clamps based, first, on the module frame thickness and then on the quantity of modules to install. SnapNrackclamps are available individually, in bulk packs, and in a 3-module clamp set. You can also buy bulk end clamps and mid clamps onthe next page. See the examples below.Example 1: Evergreen ES-A-200 modules have a 1.8-inch thick frame. Eight (8) ES-A-200 modules require a 1.8-inch 3-module set(item code 015-09929) and 10 mid clamps (item code 015-09903, or one 12-pack item code 015-09904).Example 2: REC 210-230 AE-US modules have a 1.69-inch thick frame. Seven (7) REC 215 AE-US modules require a 1.69-inch3-module set and 8 mid clamps.3- Module Clamp Sets w/ bolts & nutsClear aluminumFrame depthModulesItem codeBlack anodizedPriceItem codePrice1.34"SolarWorld SW230015-09910 22015-09911 271.4"Kyocera GX-LP015-09916 22015-09917 271.5"REC - PE015-09951 22015-09952 271.6"Evergreen ES-C 80/120015-09920 22015-09953 271.69"REC-AE-US015-09925 22015-09925 271.8"Evergreen ES-A & Mitsubishi015-09929 22015-09931 271.97"SCHOTT POLY015-09934 22015-09937 27Please call us with any questions! Our contact information is on the cover.29Roof MountsDescriptionBlack anodized
Mounting StructuresSnapNrack Bulk SnapNrack Module Top ClampsOrder bulk clamps from the table below. For each rowof modules, you will need 2 mid-clamps for each spacebetween two modules in the row, and 4 end-clamps. Forexample, a four-module row would need 6 mid clamps.Use end clamps that match the module frame thickness oruse Universal End Clamps for any module with a typicalinternal L-frame.Bulk Module Clamps w/ bolts & nutsClear aluminumDescriptionSingle piecesFramedepthModulesItem codeBlack anodized12 packPriceItem codeSingle piecePriceItem code12 packPriceItem codePriceMid clamp 2"015-09903 4 015-09904 29 015-09906 6 015-09907 37Mid clamp2" 015-09905 4 015-09902 29 015-09871 6 015-09872 37Universal end clampAllAll brands015-09943 7 015-09944 751.34SolarWorld015-09909 4 015-09913 35 015-09912 7 015-09914 47End clampRoof MountsEnd clamp1.4AEE Series HE015-09915 4 015-09873 35 015-09918 7 015-09874 47End clamp1.5REC - PE015-09875 4 015-09876 35 015-09877 7 015-09878 47End clamp1.6Evergreen ES-C015-09921 4 015-09879 35 015-09924 7 015-09880 47End clamp1.69REC AE-US015-09923 4 015-09938 35 015-09922 7 015-09935 47End clamp1.8Evergreen ES-A , Mitsubishi,Kyocera GX-LPU & GX-LB,SANYO N Series015-09927 4 015-09928 35 015-09930 7 015-09940 47End clamp1.97SCHOTT POLY015-09933 4 015-09942 35 015-09936 7 015-09941 47015-09961 9 015-09962 86 015-09963 13 015-09964 136015-09994 13SnapNrack splice kit - single bar with hardwareSnapNrack rail end cap 12 piece - black rubberSnapNrack rail cover clear - two 48" pieces015-09995 17Tilt leg hardware kit - clear (2 L-foot with hardware)015-09972 10015-09993SnapNrack channel nut 12 pack 9SnapNrack Roof Attachment ComponentsWe offer a variety of roof attachment components. Some may be used individually and othersrequire a combination of components. For simple flush mount to a roof with composition shingleswe recommend the Flashed L-foot. If the roof has tile or thick roofing material then you probablyneed a stand-off. The Standing Seam Clamp is designed to be used to attach rails to a standingseem metal roof and is to be used in conjunction with the SnapNrack rail mounting system. TheCorrugated Roof Block is for use with standard corrugated metal roofing. It spans across a ridgeand provides a flat mounting surface for an L-foot.Roof Attachment PartsClear aluminumSingle piecesDescriptionSnapNrack L-foot - clearItem code015-09978Black anodized12 packPriceItem codeSingle piecesPrice Item code Price12 packItem codePrice 5 015-09977 45 015-09979 6 015-09980 54015-09975 164 015-09985 17 015-09981 173SnapNrack Flashed L-foot015-09983 20SnapNrack standoff - 5.5"015-09973 17 015-09986 176SnapNrack standoff - 7"015-09974 19 015-09988 182015-09989 83 104SnapNrack standoff spacer 1"Corrugated Roof Block for metal roofsOatey flashing #11830 12.5" x 8.75"015-00162 10 014-00629Oatey flashing #11831 18" x 18" galv015-00163 20Commercial Standing Seam Metal Roof ClampStanding Seam Metal Roof Clamp30015-09945 9 015-09946 94Suggested retail prices are subject to change; check with us for latest pricing.
NEW! CLICKSYS Mounting systemEngineered for flush roof mounting applications, CLICKSYS is easily installed onmost roofing types, including barrel and Spanish tiles. The unique I-beam design ofCLICKSYS optimizes strength, eliminates excess material found in other systems,and offers a cost effective solution. With no drilling required and "click and secure"connections eliminating the need for nuts and bolts, CLICKSYS gets installers offthe roof in less time when compared to other competitive products. 10-year warranty.The 100-series aluminum support beams come in a mill finish, 144 inches long.Flange connections snap on to support beams without the need of hardware or tools. The 1-flange connection is for use in conjunctionwith standoffs, Quick Mount PV, or when directly installing on composite shingles using a lag bolt. The 2-flange connections comewith or without the integrated butyl backing and are designed to be secure beams to the roof using 3" Concealor screws. Concealorscrews can be driven into the structure with a cordless drill with no need for pilot holes.Mounting StructuresUniracCLICKSYS Standoffs offer more elevation for greater airflow under a finished array. They are accompanied with all hardware neededincluding a 1 flange connection and lag bolts.Quick Mount PV flashing is custom designed for CLICKSYS. Each flashing comes with 1 Flange Connection and lag hardware. Thisflashing provides a clear advantage over standard flashing techniques by increasing the height ¾" and providing a faster installation.Sliders and Top Mounting ClampsSliders hold hex bolts in place while top mounting clamps securely grip any point of the module frame, freeing you from the constraints of module mounting holes. See page 34 for module frame sizes designated by letters A-K.Unirac part #CLICKSYS parts descriptionQuantityItem codePrice010144M-0050Beam 100 Series 144"50014-04200 1,895003020C-0048Beam splice kit, clear48014-04230 97003021C-0048Beam splice kit, clear w/ grounding48014-04231 194004000M-0048Two flange connection w/ 3" screws48014-04210 419004001M-0048Two flange connection w/ 3" screws & butyl48014-04211 429004010M-0048One flange connection w/ lag bolt48014-04212 387005003C-00243" standoff w/ one flange connection24014-04215 345005004C-00244" standoff w/ one flange connection24014-04216 362005006C-00246" standoff w/ one flange connection24014-04217 395005007C-00247"standoff w/ one flange connection24014-04218 411005020S-0018QM flashing 9.5" x 12.5", SS, w/ one flange18014-04214 569002001C-0048End clamp A with slider48014-04240 133002002C-0048End clamp B with slider48014-04241 133002003C-0048End clamp C with slider48014-04242 133002004C-0048End clamp D with slider48014-04243 133002005C-0048End clamp E with slider48014-04244 133002006C-0048End clamp F with slider48014-04245 133002009C-0048End clamp J with slider48014-04246 133002010C-0048End clamp K with slider48014-04247 133002026C-0048Mid clamp A with slider48014-04250 133002027C-0048Mid clamp B-C with slider48014-04251 133002028C-0048Mid clamp D with slider48014-04252 133002030C-0048Mid clamp E-F-J - K with slider48014-04253 133008000S-0050UGC-2 grounding clip, SS, qty 5050014-04232 115Please call us with any questions! Our contact information is on the cover.Roof MountsAll components are sold in bulk quantities. See table below for quantities and pricing.31
Mounting StructuresUniracSolarMountUnirac’s SolarMount is a fast, easy, safe way to install a PV array in virtually any roof or ground installation. Bottom mounting clipsand tilt legs supplement traditional top mounting clamps. As a result, the system accommodates the widest variety of installations andassembly preferences – on the roof and on the ground. Any framed module sold in North America can be mounted using SolarMount.Once you’ve selected the PV modules and planned your installation layout, you’re ready to choose SolarMount components. Thetable on the following page shows what components to use if you are bottom-mounting the modules. The table on page 34 showswhat parts to use if you are top-mounting the modules. If you need tilt legs for the mounts, see the explanation on page 36. Rail andparts to complete your mounting system can be found on pages 35 to 37.When sizing is complete, rails, splices, and L-feet may be ordered in two ways: In kits or in bulk. 2- and 4-rail kits on page 35 containjust the right quantities of each component for a given installation.The 8-piece bulk rail bundles on page 35 require the addition of L-feet, and splices when necessary, along with top-mount clamps(either bulk or in pre-packaged sets) or back mount clips.Roof MountsUnirac SolarMount rails can bemounted vertically or horizontally.Choose a Top-Mounting or Bottom-Mounting SystemOn pitched roofs, mount rails either parallel or perpendicularto the rafters Assembly sequence is a common determiningfactor. Select top-mounting clamps if you prefer to installmodules last – after you’ve attached rails to installed footings.This sequence is especially convenient with modules that haveMulti-Connect cables. Select bottom mounting clips if youplan to attach modules to rails prior to final installation. Thissequence is well suited for modules that must be pre-wired.Bottom-mounting clips use space more efficiently becausethey do not require the 1" space between modules needed bytop clamps.The use of top-mounting clamps is generally easier whenflush-mounting to a roof. Always use top-mounting clamps32when flush mounting to standoffs. If using bottom-mountingclamps with L-feet, follow the installation manual carefully tomake sure footing slots are accessible during final installation.In roof mounts, when using top-mounting clamps, no extra roofbracing is needed since rails or mounting feet can be adjustedto match rafter spacing. With bottom-mounting clamps, spacingbetween the rails depends on spacing between the mountingholes of your particular PV module, and it is unlikely that theywill match rafter spacing if rails are mounted parallels to rafters.In that case, place a stringer over the roof or mounting blocksbeneath it. Never attach footings to the sheathing alone – suchan arrangement will not meet code and will leave the installationand roof vulnerable to severe damage from wind.Suggested retail prices are subject to change; check with us for latest pricing.
Mounting StructuresSolarMount Bottom-Mounting SizingRail set lengthsThis table lists the length of the rails required for many common modules. Ifyou need rail sizing for a module not listed below, please contact us.Order bulk bottom mount clips below.Rail Length Sizing - Bottom Mount ClipsRail length (inches) by number of modules per rowModule brand and 40264BP380, 4168192216240276300324BP3160, BP4160, BP41707296132156192226252288312348384ES-A 40264288312KD180GX-LP, KD205-210, 300336372408UJ6 series 212 to 23584120168204240276324360396432AE & PE series84120168204240276324372408SANYOHIT-205N, 210N,215N7296132168192240264288324360SCHOTTPOLY 217 to 2156168192216240252ND-L3EJE (123 watt)6084106132168192216240264288324Sharp Solar ND-167U1, ND-167U384120168204240288324360396NE-165U1, NE-170U172106132168204240264300336360396ND-U216 to ND-U23084120168204240276324360396432SolarWorld SW220 to 23584120168204240288324360396STP110 to 17572106132168204226264300324STP190 to 210 & STP260 to 28084120168204240276324360396SPR200, 210. 215. 22072106132168204240264300336AEEBP SolarEvergreenKyoceraMitsubishiREC SolarSuntechSunPowerUnirac part #321002Description20 ea. clipsBottommounting clipWeight (lbs) Item code5384360396360396Cable TiesBottom-Mount ClipsOrder 4 clips for each module in yourarray. Clips are packed with stainlesssteel bolts and flange nuts. For use withall modules with mounting holes on thebacks of their frames.Roof Mounts2014-00875Price 39Cable ties fit into 1/4-inchholes drilled along mounting rails.Unirac #Description990104 100 ea. push mount cable tiesPlease call us with any questions! Our contact information is on the cover.Quantity Item code1014-00895Price 1233
Mounting StructuresUniracSolarMount Top-Mounting SizingClamp sizes & rail set lengthsUse this table to determine the size of top mounting clampsfor your modules and the length of the rails requiredfor your array. When sizing is complete, rails, clamps,splices, and L-feet may be ordered in kits that containjust the right quantities for a given installation or in bulkpackaging (Pro-Paks). See pages 35 to 37 for pricing. AllUnirac components have a 10-year product warranty anda 5-year finish warranty.Rail Length Sizing - Top MountsModule brand and modelRail length in inches, by number of modules per 6252264AEE SolarAE-80HEBP380, BP485E487296120144156180192216240252BP SolarBP3125E6096120144168204226252288312336BP3150, 3160, 4160, 4170, 4175,E72106132168204240264300324360396Roof MountsEvergreenKyoceraMitsubishiREC SolarES-A-200 to KD180-230 GX-LPU, 44168192216240276300324MF165EB4, 106144180216240276312348384420360396UJ6 series 212 to 235F84132168204252288324372408AE seriesJ84132168204252288324372408PE seriesD84132168204252288324372408SANYOHIT-205N, 210N, 215NF72106144168204240276312336SCHOTTPOLY 217 to 156180204226252276ND-L3EJE (123 2168216252288336372408372408Sharp SolarSolarWorldSunPowerSuntechNE-175UC1, NE-170U1, NE-185UC1F72106144180204240276312348ND-200U1 to ND224UC1 & NDU230CF84132168216252288336372408SW220 to SW245C84132168204252288324372408SPR200, 210. 215. 220F72106132168204240264300336360396STP110-24Ab, 0 to 210 & STP260 to 280E84132168204252288324372408SolarMount Standard Rail KitsEach kit mounts a single row of modules and consists of rails plusL-feet and hardware to attach feet to rails. Splice bars are alsoincluded in four-rail kits. To determine row lengths required foryour installation, see the sizing table on this page for arrays withtop mounting clamps, or the table on page 33 for arrays with bottom mounting clips. Rails, L-feet, and splices are clear-anodized.Mount rails parallel or perpendicular to rafters.34Where foot spacing must exceed 48 inches, Standard Rail provides the extra strength needed. Install an array flush to a roof orother mounting surface in high profile (rails parallel to rafters)or low profile.With Standard Rail, there are accessories to handle special circumstances, such as Spanish tile or an uneven roof.Suggested retail prices are subject to change; check with us for latest pricing.
Two-Rail Unirac SolarMount Kits – L-feet IncludedRaillengthUnirac part # # of L-ft Weight (lbs)Item codePrice48300201413014-01020 11060300202414014-01024 12772300203416014-01028 14584300204417014-01032 16296300205419014-01036 179106300206420014-01040 196120300207622014-01044 217132300208624014-01048 234144300209625014-01052Bulk Rail BundlesUse Unirac Pro-Pak components for large installations or whenregularly using SolarMount Standard Rail on multiple installations.Bulk bundles of Standard Rail consist of 8 rails and do not includeL-feet or hardware. See the bottom mount sizing table and/or thetop mount sizing table to determine rail length appropriate foryour installation. If desired rail length exceeds 240 inches, ordera splice and two segments. Spliced segments should be equal oras close to equal as possible.Pro-Pak Standard Rail Bundles – 8 railsRail LengthUnirac part #Ship wt. (lbs)Item codePrice4830010132014-00810 2587230010348014-00812 3478430010454014-00813 3929630010562014-00814 43710630010668014-00815 48112030010780014-00820 533 25013230010888014-00821 58330010995014-00822 633300110102014-00823 683300210627014-01056 267168300211628014-01060 284156180300212630014-01064 307168300111109014-00824 734300112116014-00825 785192300213831014-01068 323180204300214833014-01072 340192300113123014-00826 835216300215834014-01076 357204300114130014-00827 856216300115137014-00828 936228300116144014-00831 975240300117152014-00829 1,0264-rail kits for long rowsEach kit contains four rail segments; two splices; L-feet; and hardware to join L-feet to rails. Rail segments and splices assemble intotwo spliced rails equal to the row length. Ship via truck freight only.Four-Rail Unirac SolarMount Kit - L-feet IncludedRaillengthSegmentlengthUniracpart ## of Ship wt.L-ft(lbs)Item code226106/12030022410014-0100040Splice Bars and PlatesPrice 391240120/1203002251042014-01001 408252132/1203002261044014-01002 425264132/1323002271046014-01003 436276144/1323002281047014-01004 453288144/1443002291048014-01005 470300156/1443002301250014-01006 492312156/1563002311252014-01007 509324168/1563002321253014-01008 525336168/1683002331254014-01009 542348180/1683002341456014-01010 559360180/1803002351458014-01011 571372192/1803002361459014-01012 587Splice bars are used to join together lengths of SolarMount Rail orSunFrame. Splice plates are also structural and may be used onlywith SolarMount Standard Rail. Expansion joints allow for thermalexpansion and may be necessary when rails exceed 30 feet. Onlysplice bars may be used for thermal expansion joint. To create anexpansion joint, slide the splice bar into the footing slots of bothrail lengths. Leave a half inch between the segments. Secure thesplice bar with two screws on one side only. Footings (such asL-feet or standoffs) should be secured normally on both sides ofthe splice. No PV module should straddle the expansion joint.384192/1923002371460014-01013 604396204/1923002381462014-01014 621408204/ 2043002391464014-01015 637Unirac part #420216/ 2043002401665014-01016 661310216432216/ 2163002411666014-01017 671310229Splices for Standard Rail with HardwareDescriptionWt. (lbs)Item code20 ea splice plates14014-00888 27120 ea splice bars10014-01267 112Please call us with any questions! Our contact information is on the cover.Price35Roof Mounts156144Mounting Structures2-rail kits in lengths up to 216 inchesEach kit contains: two rail segments equal to the row length;L-feet; and hardware to join L-feet to rails. Rail kits 106 inchesand shorter ship by UPS. Longer rail sets ship by truck freight. Tomake up long rail kits that are UPS shippable, use two rail kits of106 inches or less and splices to connect them together.
Mounting StructuresUniracHigh-Profile Adjustable Tilt LegsIn high-profile arrays, tilt angle depends on the length of the legsand the rails. To determine the length of your rails, consult this topmounting arrays sizing table and/or this bottom mounting arrayssizing table. Quantity of tilt legs required: Order one high profiletilt leg kit for each rail kit.Low-Profile Tilt LegsLow-profile orientation minimizesthe vertical height of your array tohide an array behind a parapet orminimize wind loading. You can alsooptimize tilt angle on a pitched roofto maximize system performance. Inlow profile arrays, tilt angle dependson leg length and the location of themodule mounting holes. Each lowprofile tilt leg kit contains one squaretube and one strut.Rails 120 inches and longer require leg kits with 4 legs per kit –one long leg and one short leg per rail.Quantity of LegsRequiredRail length(inches)No. of legsrequired48 to 1062120 to 1803192 to 2164226 to 2885300 to 3366348 to 4087420 to 4328Tilt angles for low-profile legsChoose (a) the correct maximumleg extension for your desired tiltangle from the table below and (b)the number of kits required from thetable at right. Item codes in tablebelow.If ordering bulk rail packs, order one high-profile tilt leg kit foreach pair of rails required in your installation. Do not use highprofile legs with rails longer than 180 inches. Never use splicedrails with this configuration.Roof MountsQuantity of tilt legs requiredThe number of tilt legs in a low-profile array depends on the lengthSizing Table for Unirac Low-Profile Tilt Legs(Tilt angle range given in degrees from horizontal.)of the mounting rails.Low profile leg length:Unirac part #12-inch30-inch44-inch310121310122310123Item code 014-01185 014-01189 014-01193PriceModule make and model 36 45 52Sizing Table for High-Profile Tilt Legs(Tilt angle range is in degrees from horizontal.)One Leg Per Rail (2 legs per kit) – for Rails 48" to 106"Maximum leg lengthUnirac part #Item codeTilt angle range (degrees)PriceAEE Solar AE80HE, AE90HE15-1931-4945-60Evergreen ES-A-20016-2034-5348-60KC65, 85, /LPU7-1422-4033-60HIT205N, 210N, 0-60165, 175, 18512-1525-3936-59ND200, 20813-1627-4239-60Unirac part #SW23014-1830-4743-60Item codeKyoceraSANYOSharpSolarWorldREC12 "44 "72 "310107310108310109014-01160014-01164014-01168 51 78 103Rail LengthTilt angle range (degrees)489 - 2130 - 60N/A607 - 1724 - 6037 - 60726 - 1419 - 5431 - 60845 - 1217 - 4626 - 60964 - 1014 - 4023 - 601064-913 - 3621 - 60Two Legs per Rail (4 legs per kit) – for Rails 120" to 180"Maximum leg length18 inch64 inch104 inch310111310112310110014-01172014-01176014-01180 96 161 217SW165/17512-1525-3936-60AE-US and PE14-1830-4743-60Rail length17-2237-5853-601205 - 1017 - 3826 - 60SunPower SPR200, 210, 215, 220PriceTilt angle range (degrees)SCHOTTPOLY 217 - 23014-1830-4743-601326 - 1017 - 3724 - 60SuntechSTP110-24b, STP1759-1219-3028-451446-916 - 3322 - 43UE12515-1931-5045-601565 - 1014 - 3020 - 4912-1525-3936-601685-713 - 2818 - 4613-1627-4239-601803-712 - 2617 - 43Mitsubishi UD190/185UJ23036Suggested retail prices are subject to change; check with us for latest pricing.
Standoffs are sold in packs of 12 and come with stainless-steelhardware and 2 lag bolts. Use flat-top standoffs with L-feet toattach solarmount or SunFrame railsHeight(inch)Wt.(lbs)Uniracpart #Item codePriceFlat-top 2-piece, Clear-anodized1-5/8" OD Aluminum Standoffs39310553014-00789 153410310554014-00791 165612310556014-00793 189713310557014-00795 202Flat-top 2-piece, Bronze-anodized1-5/8" OD Aluminum Standoffs39310653014-00797 160410310654014-00799 173612310656014-00801 197713310657014-00803 209Flat-top One Piece Zinc-PlatedSteel 1-5/8" O.D. Standoffs16310051014-00661 214418310052014-00662 224622310053014-00664 23324310054014-01233 2557Raised-Flange Zinc-Plated Steel1-5/8" O.D. Standoffs316310047014-01237 221418310048014-01241 245622310049014-01245 262725310050014-01249 275ShimsThe end clamps and mid clamps come with stainless steel T-boltsand flange nuts. The H clamps, which can be used as mid and endclamps, come with hex bolts.Uniracpart #Wt.(lbs) Item codeDescriptionPriceEnd Clamps with Stainless Steel T-Bolts and Flange Nuts320012 20 ea. A clamps320013 20 ea. B clamps66014-00840014-00841 44 4432001432008132001532018520 ea. C clamps20 ea. C clamps; dark bronze20 ea. D clamps20 ea. D clamps dark bronze6666014-00842014-00861014-00843014-00863 44 57 44 5732001632001732012332008320 ea. E clamps20 ea. F clamps20 ea. F clamps dark bronze20 ea. G clamps dark bronze6666014-00844014-00845014-00846014-00847 44 44 57 576014-00849 44320079 20 ea. J clamps320221 20 ea. K clamps3014-00860 44Mid Clamps with Stainless Steel T-Bolts and Flange Nuts320020 20 ea. A-B-C mid clamps6014-00867 49320084 20 ea. A-B-C mid clamp
Clear aluminum Black anodized Item code Price Item code Price 1.34" SolarWorld SW230 015-09910 22 015-09911 27 1.4" Kyocera GX-LP 015-09916 22 015-09917 27 1.5" REC - PE 015-09951 22 015-09952 27 1.6" Evergreen ES-C 80/120 015-09920 22 015-09953 27 1.69" REC-AE-US 015-09925 22 015-09925 27
The Water & Sewer Board - Water Works & S 150 Jennifer Lane Oxford AL 36203 (256) 831-0160 Ozark Utilities BD Meter 400 Peacock Parkway Ozark AL 36360 (334) 445-4595 Ozark Utilities BD Waste Water 2872 S
Missouri Valley Chapter Volume XII Number 2A Summer 2006 News Letter OZARK ROCK MASONRY IN SPRINGFIELD, CA 1910-1955 by Debbie Sheals Ozark rock masonry is arguable the most distinctive genre of 20th century vernacular architecture found in Missouri. In its use of local materials and simple forms, Ozark rock
Harness Wiring Diagram. Se lect the snowmobile from the chart to determine the correct diagram. Snowmobile Models Ignition Harness Bearcat W/T B Mountain Cat 500 H Mountain Cat 570 A Mountain Cat 600 EFI/600 EFI LE G Mountain Cat 800/800 LE I Mountain Cat 800 EFI/800 EFI LE K Mountain Cat 1000 E Pantera 550 B Pantera 600 EFI G Pantera 800 EFI K
Hunter Mountain at 4,040 feet, Southwest Hunter at 3,740 feet, Rusk Mountain at 3,680 feet, Evergreen Mountain at 3,360 feet, Pine Island Mountain at 3,140 feet and Packsaddle Mountain at 3,100 feet. The peaks form. an east-west ridge from the Devil's Tombstone Campground along Route 214 to the Hamlets of Lexington and Spruceton along Route 42 .
lion ecology. This document presents information about mountain lion biology, physiology, and behavior; explains how to determine the gender of a mountain lion; and details some of South Dakota's laws and regulations pertaining to mountain lion hunting. Mountain Lions in South Dakota Mountain lions are native to the Black Hills of South Dakota.
1972:295). A 227 pound male mountain lion killed by President Theodore Roosevelt in 1901 near Meeker, Coloradoremains among the heaviest mountain lions recorded from Nonh America (Young 1946: Anderson 1983). Statewide, mountain lion numbers were believed to have declined since the early 1900's(Armstrong 1972). In 1967. the mountain lion .
Greene County has the highest market share and retail sales in the Ozark region. The map above shows the retail market area for Greene County from which retail customers and stores purchase apparel, furniture, general merchandise and miscellaneous retail goods.
Automotive EMC : Numerical Simulation for Early EMC Design of Cars Flavio CANAVERO 1, Jean-Claude KEDZIA 2, Philippe RAVIER 3 and Bernhard SCHOLL 4 1 Politecnico di Torino - Corso Duca degli .
