0-10V Drivers (D010) - Compatible Controls

0-10V drivers (D010) - Compatible controls: Linear controls (our EldoLED drivers are programmed to Linear dimming curve by default):o Lutron Diva DVSTV (Wallbox dimmer)o Lutron Nova T NTSTV (Wallbox dimmer)o Lutron Maestro MS-Z101/MS-Z101-V (Wallbox dimmer/sensor)o Lutron PowPak 0-10V RMJ-5T-DV-B (Energi Tripak)o Lutron GRX-TVI (0-10V interface for Grafik QS and some commercial dimming panels)o Lutron TVI-LMF-2A (EcoSystem to 0-10V interface)o Lutron QSN-4T16-S (Energi Savr Node 0-10V)o Lutron TVM2 module (HomeWorks and commercial dimming panels)o Sensor Switch nIO-EZ Logarithmic controls (PLEASE NOTE: if programming the Eldoled drivers to a logarithmic dimmingcurve is required, consult factory before ordering, and add the MOD LOG suffix to theappropriate driver part #):o Leviton IllumaTech IP710-DLXo Lightolier ZP600FAM120o Pass & Seymour CD4FB-W (Requires a PWP120277 Power Pack)o Synergy ISD BCo Crestron GLX-DIMFLV8, GLXP-DIMFLV8o Crestron GLPAC-DIMFLV4-x, GLPAC-DIMFLV8-xo Crestron GLPP-DIMFLVEX-PMo Crestron GLPP-1DIMFLV2EX-PMo Crestron GLPP-1DIMFLV3EX-PM, DIN-AO8o Crestron DIN-4DIMFLV4, CLS-EXP-DIMFLVo Crestron CLCI-1DIMFLV2EXMaximum Lead Length (Constant Current)*Wire GaugeMaximum Lead Length1872 ft (22 m)16118 ft (36 m)14150 ft (46 m)12200 ft (61 m)Maximum Lead Length (Constant Voltage 24V)*Wire gaugeLoad per driver 48W 72W 2AWG151'101'75'#10AWG241'160'120'*Actual distance must be calculated by installer.Must comply with NEC code.inter-lux.com1410.381.1497

Lutron EcoSystem drivers (DES/PEQ) - Compatible controls:Part NumberLutron EcoSystemCompatible Controls120 V PowPak Dimming ModulesEcoSystemLoops perControl277 V Drivers perEcoSystemLoopMaximumDrivers -SEnergi Savr NodeN/AQSN-2ECO-SGRAFIK Eye QS / HomeWorksQS control unitDrivers per ControlQSGRJ- E (wireless)QSGR- EN/AQP2- 2CQP2- 4CQuantum HubQP2- 6CN/AQP2- 8CHomeWorks QS /myRoom Plus power moduleLQSE-2ECO-DN/A1 All devices connected to one FCJ/FCJS-ECO will be controlled together. Devices will dim to the same level as the result of a control command.For more detail on adjusting low-end light level refer to Application Note #556 (048556) at www.lutron.comMaximum Lead Length (Constant Current)Wire Gauge150 mA to700 mA18 AWG (0.75 mm2)16 AWG (1.5 mm2)14 AWG (2.5 mm2)12 AWG (4.0 mm2)710 mA to1.50 A1.51 A to2.10 A30 ft (9 m)15 ft (4.5 m)10 ft (3 m)35 ft (10.5 m)25 ft (7.5 m)15 ft (4.5 m)50 ft (15 m)40 ft (12 m)25 ft (7.5 m)100 ft (30 m)60 ft (18 m)40 ft (12 m)Wire GaugeMaximum Lead Length (Constant Voltage 24V)18 AWG (0.75 mm2)16 AWG (1.0 mm2)40 ft (12.2 m)14 AWG (1.5 mm2)12 AWG (2.5 mm2)100 ft (30.5 m)10 AWG (4.0 mm2)Wire Gauge60 ft (18.3 m)150 ft (45.7 m)Digital EcoSystem Link Length (max)12 AWG2200 ft14 AWG1400 ft16 AWG900 ft18 AWG550 ftinter-lux.com25 ft (7.62 m)2410.381.1497

Lutron Forward Phase 2-wire drivers (DFPN) - Compatible controls:Controls Requiring NeutralCompatible Controls: Lutron Neutral-wire DimmersABBBCBDrivers per ControlB: End of Gang C: Middle of GangLow-End Setting /Load-Type Setting 1A: Not GangedRadioRA 2RRD-6NAadaptive dimmer *RA2 Select / RadioRA 2 600 W RRD-6NDdimmerHi-lume 1% 2-Wire LTE LED 21 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxHi-lume 1% 2-Wire LTE LED 21 – 8, 350 W max1 – 8, 350 W max1 – 8, 350 W maxRadioRA 21000 W dimmer *RRD-10ND-Set Device type to “INC/MLVNeutral Dimmer”; Set High-End Trimto 99%; Set Low-End Trim to 35%1 – 131 – 131 – 13RadioRA 2 Architectural RFGRAFIK T phase selectabledimmer 3RRT-G5NEW-3Trim low-end per APM App Note(Lutron P/N 048534)1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxRadioRA 2 Architectural RFGRAFIK T dimmerRRT-G25LW-Trim low-end per APM App Note(Lutron P/N 048534)1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxRadioRA 2 C L hybridseeTouch keypadRRD-HNHi-lume 1% 2-Wire LTE LED1 – 10, 200 W max1 – 10, 200 W max1 – 10, 200 W maxRadioRA 2 GRAFIK T C Lhybrid keypadRRT-GHHi-lume 1% 2-Wire LTE LED1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxHomeWorks QS adaptivedimmer *HQRD-6NA-Hi-lume 1% 2-Wire LTE LED 21 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxHomeWorks QS600 W dimmer *HQRD-6ND-Hi-lume 1% 2-Wire LTE LED 21 – 8, 350 W max1 – 8, 350 W max1 – 8, 350 W maxHomeWorks QS1000 W dimmer *HQRD-10ND-Hi-lume 1% 2-Wire LTE LED 21 – 131 – 131 – 13Maestro Wireless 600 Wdimmer *MRF2-6ND-120-Trim low-end per APM App Note(Lutron P/N 048370)1 – 8, 350 W max1 – 8, 350 W max1 – 8, 350 W maxVive Maestro Wireless 600 W MRF2S-6ND-120- Trim low-end per APM App Notedimmer *(Lutron P/N 048370)1 – 8, 350 W max1 – 8, 350 W max1 – 8, 350 W maxHomeWorks QS GRAFIK Thybrid keypadHi-lume 1% 2-Wire LTE LED1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxHomeWorks QS Architectural HQRT-G25LWGRAFIK T dimmerHi-lume 1% 2-Wire LTE LED1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxHomeWorks QS ArchitecturalGRAFIK T phase selectableHQRT-G5NEW-3dimmer 3Hi-lume 1% 2-Wire LTE LED1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxHomeWorks QS designerC L hybrid seeTouch keypad HQRD-HNHi-lume 1% 2-Wire LTE LED1 – 10, 200 W max1 – 10, 200 W max1 – 10, 200 W max1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxProductPart NumberHQRT-GHGRAFIK T C)L250 W dimmer *GT-250M-,GTJ-250M-Set low-end trim per dimmerinstallation instructionsCaséta Wireless Pro1000 W dimmer *PD-10NXD-Trim low-end per instructions atwww.casetawireless.com/lowend1 – 131 – 131 – 13Caséta Wireless phaseselectable dimmer 3PD-5NE-3Trim low-end per instructions atwww.casetawireless.com/lowend1 – 20, 400 W max1 – 20, 400 W max1 – 20, 400 W maxMaestro PRO phaseselectable dimmerMA-PRO3Trim low-end per APM App Note(Lutron P/N 048703)1 – 20, 400 W max1 – 20, 400 W max1 – 20, 400 W max1Note: All wattages are in terms of input wattage to the LED driver.Setting the low-end trim and load type is necessary to ensure optimal performance and 1% dimming capability.23Note: For information about Legacy Product use in existing control application, contact LEDs@lutron.comAlso listed as “LED Lutron A-Series 2-Wire” or “Hi-lume A-Series LTE LED Driver 2-Wire” in previous software releases.Not compatible in default mode (reverse-phase). Dimmer must be changed to forward-phase.inter-lux.com1410.381.1497

Lutron Forward Phase 2-wire drivers (DFPN) - Compatible controls:Controls Requiring Neutral (continued)Note: Colors shown correspond to terminals on driver.Wiring DiagramLutronDimmingModule/PanelLineDimmed Line (Black)Hi-lume1% 2-WireLED DriverNeutralNeutral V (Red)2Ground1Neutral (White)–V (Black)2Ground1Ground (Green)112LEDLightEngineGround wire connection available on K case models only. Fixture and driver case must be grounded in accordance with local and national electrical codes.For maximum driver-to-LED light engine wire length, see charts in Driver Leads section at the end of the document.Compatible Controls: Lutron Dimming Modules/PanelsGuaranteed performance specifications with the controls listed in the chart below.For assistance selecting controls, contact our LED Center of Excellence at 1.877.DIM.LED8 or LEDs@lutron.comProductPart NumberDrivers per Control Low-End Setting/Load-Type Setting 11 – 6 (per output); 1 Amaximum driver inputcurrent1 – 6 (per output); 1 Amaximum driver inputcurrent1 – 6 (per output); 2 Amaximum driver inputcurrentmyRoom DIN power module *MQSE-4A1-DHi-lume 1% 2-Wire LTE LED 2HomeWorks QS DIN power module *LQSE-4A1-DHomeWorks QS Phase AdaptiveDIN power module 3LQSE-4A-120-D 3HomeWorks QS wallbox power module *HQRJ-WPM-6D-1201 – 10 (per output); 26total per moduleHi-lume 1% 2-Wire LTE LED 2HomeWorks wallbox power module *HWI-WPM-6D-1201 – 10 (per output); 26total per moduleSet load type to “GRX‑FDBI” or “GRX-TVI”GRAFIK Eye QS control unit *QSGR-,QSGRJ-1 – 10 (per output); 26total per unitSet load type to “Fluorescent Module”GRAFIK Eye 3000 control unit *GRX-3100-,GRX-3500-1 – 10 (per output); 26total per moduleSet load type to “GRX‑FDBI” or “GRX-TVI”RPM-4U module (LCP, HomeWorks QS,GRAFIK Systems, Quantum) *HW-RPM-4U-120,LP-RPM-4U-1201 – 26 (per output); 26total per moduleHi-lume 1% 2-Wire LTE LED 2RPM-4A module (LCP, HomeWorks QS,GRAFIK Systems, Quantum) *HW-RPM-4A-120,LP-RPM-4A-1201 – 13 (per output); 26total per moduleHi-lume 1% 2-Wire LTE LED 2GP dimming panels *Various1 – 26Set load type to “2-1”Hi-lume 1% 2-Wire LTE LED 2Hi-lume 1% 2-Wire LTE LED 2Set load type to “2-1”Set load type to “2-1”12Setting the low-end trim and load type is necessary to ensure optimal performance and 1% dimming capability.Also listed as “LED Lutron A-Series 2-Wire” or “Hi-lume A-Series LTE LED Driver 2-Wire” in previous software releases. 3Not compatible in default mode (reverse-phase). Additional configuration is necessary in forward-phase.inter-lux.com1410.381.1497

Lutron Forward Phase 2-wire drivers (DFPN) - Compatible controls:Controls Not Requiring NeutralNote: Colors shown correspond to terminals on driver.Wiring ral V (Red)2Dimmed Line (Black)Ground1Neutral (White)Hi-lume1% 2-WireLED DriverLEDLightEngine–V (Black)2Ground1Ground (Green)1Ground wire connection available on K case models only. Fixture and driver case must be grounded in accordance with local and nationalelectrical codes.2For maximum driver-to-LED light engine wire length, see charts in Driver Leads section at the end of the document.1Compatible Controls: Lutron Non-Neutral DimmersGuaranteed performance specifications with the controls listedin the chart below.AFor assistance selecting controls, contact our LED Center of Excellenceat 1.877.DIM.LED8 or LEDs@lutron.comBBBCBDrivers per ControlB: End of Gang C: Middle of GangProductPart Number Low-End Setting/Load-Type Setting 1Ariadni C L250 W dimmer *AYCL-253P-Set low-end trim dial to 1 o’clock. Adjustslightly if needed. See dimmer installationinstructions on how to adjust low-end trim.1 – 8, 350 W max1 – 8, 350 W max1 – 8, 350 W maxAriadni C L150 W dimmerTGCL-153P-,AYCL-153P-Set low-end trim dial to 1 o’clock. Adjustslightly if needed. See dimmer installationinstructions on how to adjust low-end trim.1 – 6, 250 W max1 – 6, 250 W max1 – 6, 250 W maxDiva C L250 W dimmer *Set low-end trim dial to 10 o’clock. AdjustDVCL-253Pslightly if needed. See dimmer installationDVSCCL-253P- instructions on how to adjust low-end trim.1 – 8, 350 W max1 – 8, 350 W max1 – 8, 350 W maxDiva C L150 W dimmerSet low-end trim dial to 10 o’clock. AdjustDVCL-153P-,slightly if needed. See dimmer installationDVSCCL-153P- instructions on how to adjust low-end trim.1 – 6, 250 W max1 – 6, 250 W max1 – 6, 250 W maxNova T* C L250 W dimmer *NTCL-250-Set low-end trim dial to 10 o’clock. Adjustslightly if needed. See dimmer installationinstructions on how to adjust low-end trim.1 – 10, 400 W max1 – 10, 400 W max1 – 10, 400 W maxLumea C L150 W dimmerLECL-153P-Set low-end trim dial to 10 o’clock. Adjustslightly if needed. See dimmer installationinstructions on how to adjust low-end trim.1 – 6, 250 W max1 – 6, 250 W max1 – 6, 250 W maxSkylark C L150 W dimmerSCL-153P-Set low-end trim dial to 10 o’clock. Adjustslightly if needed. See dimmer installationinstructions on how to adjust low-end trim.1 – 6, 250 W max1 – 6, 250 W max1 – 6, 250 W maxContour C L150 W dimmerCTCL-153P-Set low-end trim dial to 10 o’clock. Adjustslightly if needed. See dimmer installationinstructions on how to adjust low-end trim.1 – 6, 250 W max1 – 6, 250 W max1 – 6, 250 W maxA: Not GangedNote: All wattages are in terms of input wattage to the LED driver.1Setting the low-end trim and load type is necessary to ensure optimal performance and 1% dimming capability.Note: For information about Legacy Product use in existing control application, contact LEDs@lutron.cominter-lux.com1410.381.1497