Quick Start Guide - Corning Inc.

p/n 003-877-QSG, Issue 1 1.Visit http://www.corning.com/cablesystems for the in-depth installation manual. Search for partnumber 003-877.Components731 Sliding cover2 Label card3 Mounting bracket4 Door latch5 Blank adapter panel678910Slack management clipInternal strain-relief bracket4Transitional strain-relief holderExternal strain-relief bracketJumper guide2.86952310124TPA-3902Mounting the Housing2a Press button and remove2c Slide mounting bracket notchexternal strain-relief bracket.over screw heads.2d Install next two screws inInstall two #12-24 x 0.5Press Button2a2b Phillips-head screwsanother notch of mountingbracket; tighten all screws.at desired height for the lowestpoint on mounting bracket.Leave gap behind head.2d2b2cTPA-3903STANDARD RECOMMENDED PROCEDURE 003-877-QSG ISSUE 1 September 2011 PAGE 1 OF 6 PRETERMINATED SYSTEMS CABLES CONNECTORS CABLE ASSEMBLIES HARDWARE TOOL KITS AND ACCESSORIES TEST EQUIPMENT SPLICE EQUIPMENT FAN-OUT KITS TRAINING4U Closet ConnectorHousing (CCH)

3.Accessing the Housing3a Open rear door.3c Slide housing out of frame and move to a work surface.3b Press button on inside wallon each side of the housingand pull outwards.3c3b3a3d Press up on tab underneatheach side of the cover.3e Slide cover off theback of the housing.Tab3d3eTPA-39044.Installing Adapter PanelsPress tabs on blank panels to remove.Install adapter panel. Press plungers tosecure in place.TPA-3909STANDARD RECOMMENDED PROCEDURE 003-877-QSG ISSUE 1 September 2011 PAGE 2 OF 6

5.Installing Cable for Field TerminationWARNING: Never look directly into the end of a fiber that may be carrying laser light.Laser light can be invisible and can damage your eyes. Viewing it directly does not cause pain.The iris of the eye will not close involuntarily as when viewing a bright light. Consequently,serious damage to the retina of the eye is possible. Should accidental eye exposure to laserlight be suspected, arrange for an eye examination immediately.5.1. Accessing the Cable for Field TerminationStrip Lengths for 4U HousingsCABLEDirect TerminationStrain-reliefPointLoose Tube(e.g., OSP, FREEDM )Tight-buffered(e.g., MIC , UMIC Cableor Subunit)TransitionalStrain-reliefPoint36 inchesFan-out body legs availablein 25 - 48 inches lengths36 inchesStrip to 48 inchesTPA-39055.2. Sheath RetentionRemove internal strain-relief bracketby lifting plunger (a), sliding bracket to releasetabs (b), and lifting up (c).5.2a5.2dSlide cable tie under flange.5.2b5.2c5.2ePlace cable on the strain-reliefbracket with cable tie aroundjacket as shown.5.2fReverse removal steps5.2a through 5.2c to reinstallbracket into housing withcable(s) attached.Secure cable tiearound the cable.TPA-3906STANDARD RECOMMENDED PROCEDURE 003-877-QSG ISSUE 1 September 2011 PAGE 3 OF 6

5.3. Strain-relieving to the Transitional Strain-Relief Holder5.3aOR5.3bAttach cables to transitionalholder using one of themethods in 5.3a or 5.3b.5.3aPress buffer tubefan-out bodies intotransitional holder.5.3c5.3bOR Secure tight buffercable to the transitionalholder with cable ties.You may stack the transitionalholder to accommodate morefan-out bodies or cables.TPA-39075.4. Cable Routing5.4aRoute 900 micron fibers as shown.NOTE: Reverse fiber routing if cableenters from other side of the housing.5.4b Secure fibers in slack managementclips.5.4c Clean and mate adapters andconnectors.5.4d Store buffer tube or sub-unit slackon rear door. Loosely secure withcable ties or hook-and-loop strapsthrough the lances.TPA-3910STANDARD RECOMMENDED PROCEDURE 003-877-QSG ISSUE 1 September 2011 PAGE 4 OF 6

6.Completing Installation6aReinstall cover.6b Slide housing into frame. Ensure latch engages oneach side inside the housing.6cRecord connections on label card using label provided. (Oruse Avery label 5162 [1 1/3” x 4”].) Store card on front dooror in slot in the base of the housing.TPA-3908Corning Cable Systems LLC PO Box 489 Hickory, NC 28603-0489 USA1-800-743-2671 FAX 1-828-325-5060 International 1-828-901-5000 http://www.corning.com/cablesystemsCorning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems’ products without prior notification.ClearCurve is a registered trademark of Corning Incorporated. All trademarks are the properties of their respective owners. Corning Cable Systems is ISO 9001 certified. 2011 Corning Cable Systems. All rights reserved. Published in Mexico.STANDARD RECOMMENDED PROCEDURE 003-877-QSG ISSUE 1 September 2011 PAGE 5 OF 6

TPA-3911STANDARD RECOMMENDED PROCEDURE 003-877-QSG ISSUE 1 September 2011 PAGE 6 OF 6

Cable Routing TPA-3907 Attach cables to transitional holder using one of the methods in 5.3a or 5.3b. 5.3a 5.3b 5.3a Press buffer tube 5.3b fan-out bodies into transitional holder. OR Secure tight buffer cable to the transitional holder with cable ties. 5.3c You may stack the transitiona