Hilti HIT-HY 70 Injection Mortar For Masonry

Hilti HIT-HY 70Hilti HIT-HY 70 injection mortar for masonryInjection Mortar SystemBenefits Hilti HIT-HY 70330 ml foil pack(also available as 500 mland 1400 ml foil pack)MixerHIT-V (Zinc)HIT-V-F (Gal)HIT-V-R (A4-70)HAS-E (Zinc)HAS-E-F (Gal)HAS-E-R (A4-70)HIT-AC, HIT-ACR rodc hemical injection fasteningfor all type of base materials:– hollow and solid–c lay bricks, sand-lime bricks,normal and light weight concreteblocks, aerated light weightconcrete, natural stones t wo-component hybrid mortar r apid curing versatile and convenient handling f lexible setting depth andfastening thickness s mall edge distance and anchorspacing ortar filling control withmHIT-SC sleeves suitable for overhead fastenings i n-service temperatures:short time: max.120 Clong term: max 72 CHIT-IC internal threadedsleeveHIS-RN sleeveHIT-SC composite ti anchordesignsoftwareApprovals / certificatesDescriptionAuthority / LaboratoryNo. / date of issueAllgemeine bauaufsichtliche Zulassung(national German approval)DIBt, BerlinZ-21.3-1830 / 2009-01-20Fiche technique SOCOTECSOCOTEC, ParisYX 0047 08.2006Fire test reportMFPA, LeipzigPB III/B-07-157 / 2007-06-04Assessment report (fire)warringtonfireWF 166402 / 2007-10-26page 252July 2014

Hilti HIT-HY 70Basic loading data for single anchor in masonry unitsAll data in this section applies to Load values valid for holes drilled with TE rotary hammers in hammering mode Correct anchor setting (see instruction for use, setting details) Steel quality of fastening elements: see data below Steel quality for screws for HIT-IG, HIT-IC and HIS-N: min. grade 5.8 / HIS-RN: A4-70 Threaded rods of appropriate size (diameter and length) and a minimum steel quality of 5.8 can be used B ase material temperature during installation and curing must be between -5 C through 40 CRecommended loads a) Frec for brick breakout and pull out in [kN]Hollow masonry: HIT-HY 70 with HIT-SC and HIT-AC / HIT-V, HAS, HAS-E and HIT-IG / HIT-ICHIT-AC, HIT-V, HAS, HAS-EAnchor sizeBase materialFire light brick Scoria Blendfuc b) 4 N/mm²L x H x B [mm] 230 x 110 x 119M6Settingdepth[mm]Hollow Blockfuc b) 10 N/mm²L x H x B [mm] 390 x 190 x 190Vrec[kN]Clay common (Standard)fuc b) 20 N/mm²L x H x B [mm] 230 x 110 x 76Vrec[kN]M8M10M12HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC12x 16x 16x 18x 22x 16x 18x c) 22x 22x Nrec [kN]0.50.50.50.80.8--Vrec [kN]1.01.51.51.52.0--Nrec [kN]1.81.81.81.81.81.8Towards freeedge cmin 2001.252.02.02.02.0No free edges1.252.52.83.0Nrec [kN]0.60.60.6Vrec [kN]1.01.5Nrec [kN]0.6Towards freeedge cmin 02.02.02.02.02.0No free edges1.252.52.83.03.02.52.82.83.0Nrec [kN]1.51.51.51.51.5----Vrec [kN]2.02.02.02.02.0----Nrec [kN]2.03.03.03.04.03.04.04.04.0Towards freeedge cmin 2002.02.02.02.02.02.02.02.02.0No free edges2.03.55.57.57.53.55.55.57.55080(Shell thickness 20 mm)AustraliaM125080(Shell thickness 30 mm)AustraliaM105080(Shell thickness 19 mm)AustraliaM8HIT-IG / HIT-ICVrec[kN]a) Recommended load values with consideration of a global safety factor γglobal 3.0: Frec FRk / γglobalb) fuc unconfined compressive strengthc) HIT-SC 18x with HIT-IC M10 only! HIT-IG M10 elements do not fit.July 2014page 253

Hilti HIT-HY 70Recommended loads a) Frec for brick breakout and pull out in [kN]Solid masonry: HIT-HY 70 with HIT-AC / HIT-V, HAS, HAS-E and HIT-IG / HIT-ICHIT-AC, HIT-V, HAS, HAS-EHIT-IG / HIT-ICAnchor sizeSettingdepth[mm]Base materialClay common (Dry pressed)fuc b) 14 N/mm²L x H x B [mm] 230 x 110 x 76Australia80Vrec [kN]M6M8M10M12M8M10M12Nrec [kN]-2.53.04.02.53.04.0Towards freeedge cmin 200-2.02.02.02.02.02.0No free edges-3.55.57.53.55.57.5a) Recommended load values with consideration of a global safety factor γglobal 3.0: Frec FRk / γglobalb) fuc unconfined compressive strengthpage 254July 2014

Hilti HIT-HY 70DesignInfluence of joints:If the joints of the masonry are not visible the recommended load Nrec has to be reduced with the factor αj 0.75.If the joints of the masonry are visible (e.g. unplastered wall) following has to be taken into account: T he recommended load Nrec may be used only, if the wall is designed such that the joints are to be filled with mortar. I f the wall is designed such that the joints are not to be filled with mortar then the recommended load Nrec may be usedonly, if the minimum edge distance cmin to the vertical joints is observed. If this minimum edge distance cmin can not beobserved then the recommended load Nrec has to be reduced with the factor αj 0.75.The decisive resistance to tension loads is the lower value of Nrec (brick breakout, pull out) and Nmax,pb(pull out of one brick).Pull out of one brick:The allowable load of an anchor or a group of anchors in case of pull out of one brick, Nmax,pb [kN], is given in thefollowing tables:Clay bricks:All other brick types:brick breadth bbrick [mm]Nmax,pb[kN]bricklengthlbrick[mm]brick breadth bbrick x,pb resistance for pull out of one bricklbrick length of the brickbbrick breadth of the brickFor all applications outside of the above mentioned base materials and / or setting conditions site tests have to bemade for the determination of load values.July 2014page 255

Hilti HIT-HY 70MaterialsMaterial quality HASPartMaterialThreaded rodHAS-(E), HAS-(E)-(F)Strength class 5.8, EN ISO 898-1, A5 8% ductile steel galvanized 5 µm,EN ISO 4042 (F) hot dipped galvanized 45 µm, EN ISO 10684Threaded rodHAS-(E)RStainless steel grade A4, A5 8% ductile strength class 70,EN ISO 35061, EN 10088: 1.4401WasherISO 7089Steel galvanized, EN ISO 4042;Stainless steel, EN 10088: 1.4401Strength class 8, ISO 898-2steel galvanized 5 µm, EN ISO 4042NutEN ISO 4032Strength class 70, EN ISO 3506-2, stainless steel grade A4,EN 10088: 1.4401Strength class 70, EN ISO 3506-2, high corrosion resistant steel,EN 10088: 1.4529; 1.4565Material quality HIT-APartMaterialHIT-AC rodCarbon steel grade 5.8; galvanized tomin. 5 µmHIT-ACR rodStainless steel, grade A4-70; 1.4401HIT-AN rodCarbon steel grade 3.6; galvanized to min. 5 µmMaterial quality sleevesPartMaterialHIT-IG sleeveCarbon steel 1.0718; galvanized to min. 5 µmHIT-IC sleeveCarbon steel; galvanized to min. 5 µmHIT-SC sleevePA/PPSettingInstallation equipmentAnchor sizeRotary hammerOther toolspage 256M6M8M10M12TE2 – TE16blow out pump, set of cleaning brushes, dispenserJuly 2014

Hilti HIT-HY 70Setting instructions in solid base materialsJuly 2014page 257

Hilti HIT-HY 70Setting details: hole depth h0 and effective anchorage depth in solid base materialsSetting details HIT-AC, HIT-V, HIT-V, HAS-E, HAS-E-F, HAS-E-RHIT-AC, HIT-VAnchor sizeHIT-V, HAS-E, HAS-E-F, HAS-E-R c)M8M10M12M8M10M12M16Nominal diameter of drill bitd0[mm]10121410121418Effective anchorage depthhef[mm]8080808090110125Hole depthh0[mm]8585858595115130Minimum base material thicknesshmin[mm]110110110110120140170Diameter of clearance hole in the fixturedf[mm]912149121418Minimum spacing a), b)smin[mm]100100100100100100100Minimum edge distance a)cmin[mm]100100100100100100100Torque momentTinst[Nm]5810581010[ml]457461015Filling volumea) In case of shear loads towards a free edge: cmin 200 mmA distance from the edge of a broken brick of cmin 200 mm is recommended, e.g. around window or door frames.b) Recommend to place one anchor per brick, in the middle of the brick face.c) Refer the Recommended loads table for the required setting depth.page 258July 2014

Hilti HIT-HY 70HIT-IG, HIT-ICHIS-N/RNSetting details HIT-IG, HIT-ICHIT-IGAnchor sizeHIT-ICHIS-N/RN c)M8M10M12M8M10M12M8M10M12Nominal diameter of drill bitd0[mm]141818141618141822Effective anchorage depthhef[mm]80808080808090110125Hole depthh0[mm]85858585858595115130Minimum base material er of clearance hole in the fixturedf[mm]912149121491214Length of bolt engagemenths[mm]min. 10 – max. 75min. 10 – max. 75Minimum spacing a), b)smin[mm]100100100100100100100100100Minimum edge distance a)cmin[mm]100100100100100100100100100Torque momentTinst[Nm]581058105810[ml]66666661016Filling volumemin. 8 min. 10 min. 12max.20 max.25 max.30a) In case of shear loads towards a free edge: cmin 200 mmA distance from the edge of a broken brick of cmin 200 mm is recommended, e.g. around window or door frames.b) Recommend to place one anchor per brick, in the middle of the brick face.c) Refer the Recommended loads table for the required setting depth.July 2014page 259

Hilti HIT-HY 70Setting instruction in hollow base material – using 330 ml foil packpage 260July 2014

Hilti HIT-HY 70Setting details: hole depth h0 and effective anchorage depth in hollow base materialsHAS-E / HIT-AC with HIT-SCHIT-AC, HIT-V, HAS-ESetting details HIT-V / HAS-E / HIT-A with sieve sleeveAnchor sizeM6Sieve sleeve HIT SCM8M10M1212x50 12x85 16x50 16x85 16x50 16x85 18x50 18x85 22x50 22x85Nominal diameter of drill bitd0[mm]12121616161618182222Effective anchorage depthhef[mm]50805080508050805080Hole depthh0[mm]60956095609560956095Minimum base material thicknesshmin [mm]8011080110801108011080110Diameter of clearance hole in the fixturedf7799121214141414Minimum spacing a), b)smin [mm]100100100100100100100100100100Minimum edge distance a)cmin [mm]100100100100100100100100100100Torque momentTinst [Nm]333344666612241830183018363055Filling volume[mm][ml]a) In case of shear loads towards a free edge: cmin 200 mmA distance from the edge of a broken brick of cmin 200 mm is recommended, e.g. around window or door frames.b) R ecommended one anchor per brick in the middle of the brick face. In the case of hollow concrete blocks one anchor percavity in the middle of each cavity face.July 2014page 261

Hilti HIT-HY 70Setting details: hole depth h0 and effective anchorage depth in hollow base materialsHIT-IG / HIT-IC with HIT-SCHIT-IG / HIT-ICSetting details HIT-IG / HIT-IC with sieve sleeveHIT-IGAnchor sizeSieve sleeve HIT 2x85Nominal diameter of drill bitd0[mm]162222161822Effective anchorage depthhef[mm]808080808080Hole depthh0[mm]959595959595Minimum base material thicknesshmin [mm]110110110110110110Diameter of clearance hole in the fixturedf[mm]9121491214Length of bolt engagemenths[mm]Minimum spacing a), b)smin [mm]100100100100100100Minimum edge distance a)cmin [mm]100100100100100100Torque momentTinst [Nm]346346304545303645Filling volume[ml]min. 10 – max. 75min. 10 – max. 75a) In case of shear loads towards a free edge: cmin 200 mmA distance from the edge of a broken brick of cmin 200 mm is recommended, e.g. around window or door frames.b) R ecommended one anchor per brick in the middle of the brick face. In the case of hollow concrete blocks one anchor percavity in the middle of each cavity face.page 262July 2014

Hilti H-H 70 page 252 July 2014 Injection Mortar System Hilti anchor design software Concrete Hilti HIT-HY 70 injection mortar for masonry Benefits chemical injection fastening for all type of base materials: – hollow and solid – clay bricks, sand-lime bricks, normal and light weight concrete blocks, aerated light weight concrete, natural .